Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.

Varasto- ja hankintamodulin kehittäminen toiminnanohjausjärjestelmään

Tässä diplomityössä tarkoituksena on kerätä yhteen toiminnanohjausjärjestelmän varasto- ja hankintamodulin kehittämisessä tarvittavaa teoriatietoa, sekä Nestix Oy:n asiakkaiden ja joidenkin muiden yritysten tarpeita kyseiselle ohjelmistolle. Teoria ja tarpeet yhdistetään karkeaksi ohjelmiston tarvemäärittelyksi, jonka perusteella Nestix Oy toteuttaa uudet modulit toiminnanohjausjärjestelmäänsä. Tutkimuksissa havaittiin, että yrityksillä on hyvin samankaltaisia tarpeita varastojen ja hankintojen hallintaan. Varastoinnin ja hankinnan prosessit poikkeavat hyvin vähän yritysten välillä. Samoja perinteisiä logistiikan perustyökaluja käytetään miltei kaikissa yrityksissä. Tulevaisuuden houkuttelevimpana kehitysalueena voidaan pitää ohjelmistojen internet-pohjaisuutta, joka mahdollistaa ohjelmiston käyttämisen mistäpäin maailmaa tahansa ilman erillisiä ohjelmistoasennuksia. Tutkimuksen jälkeen Nestix-ohjelmistoperheeseen toteutettiin integroidut hankinnan sekä varastoinnin modulit. Ohjelmaa on kehitetty tutkimuksen tekemisen jälkeen eteenpäin ja sitä on myyty useaan Euroopan maahan osana Nestix toiminnanohjausjärjestelmää.

The Present State and a Development Plan of Cost Accounting in Batch Production of Wind Turbine Gears

The aim of this master’s thesis was to document the present state and to create a development plan for Moventas Wind’s cost accounting. The current cost accounting system was evaluated and most fundamental problems were chosen as areas of focus in development work. The development plan includes both short- and long-term development proposals for problems identified. This report presents two alternative models for product costing. Benchmarking of cost accounting practices and modern cost accounting theories were used in development of cost accounting. It was found that the current cost accounting system functions quite well and the adjustments in unit cost rate calculation have only a minor influence on costs of goods sold. An OEE-based standard cycle concept was also developed and it was found that the implementation of this new system is worthwhile in the long-term.

Strategiset allianssit: motiivit ja muodostaminen

Strategiset allianssit ovat yhteistyömuotoja, joiden taustalla on pyrkimys pitkäntähtäimen strategisten tavoitteiden saavuttamiseen. Strategisissa alliansseissa voivat toimia niin suuret ja pienet yritykset kuin julkisen sektorin organisaatiotkin. Tässä työssä strategisista alliansseista esitetään kokonaisvaltainen ja selkeä kuva. Tämän myötä niitä käsitellään omana käsitteenään ominaispiirteineen. Lisäksi strategisten allianssien toteutusvaihtoehtoja tarkastellaan taloudelliseen ja ajalliseen ulottuvuuteen rinnastaen. Motivoituneet osapuolet ovat edellytyksenä strategisen allianssin syntymiselle ja menestymiselle. Keskeisimpiä motiiveja strategiseen allianssiin ryhtymisestä tarkastellaan arvonluonnin näkökulmasta. Motiivit ovat pohjana strategisen allianssin muodostusvaiheen käynnistymiselle. Muodostusprosessia tarkastellaan kolmivaiheisen prosessin näkökulmasta, mikä kattaa päätöksenteon, kumppanin etsinnän ja valinnan sekä neuvotteluvaiheen. Työ sisältää kaksi case-esimerkkiä, joiden tarkoituksena on luoda yhteys teorian ja käytännön välille. Ensimmäisessä esimerkissä tarkastellaan pääomasidonnaista Renault – Nissan -allianssia, joka ristiinomistukseen ja yhteisyrityksiin (joint venture) perustuen toimii monipuolisena esimerkkinä. Toisessa, Sonyn ja Philipsin allianssissa, tarkastellaan ei-pääomasidonnaisen strategisen allianssin erityispiirteitä.

Lääkintähuollon ja materiaalihallinnon yhtenäisen RFID-seurannan perusteita

Tässä diplomityössä tarkastellaan radiotaajuisen tunnistamisteknologian (RFID) seurannan yhtenäisiä perusteita puolustusvoimien lääkintähuollolle ja materiaalihallinnolle. Nykytilaa selvitettiin pääpainona lääkintähuollon ja materiaalihallinnon osa-alueet ja samalla tarkasteltiin koko puolustusvoimien RFIDtekniikan käyttöä. Puolustusvoimissa RFID-teknologiaa käytetään myös vaatehuollon ja kulunvalvonnan toiminnoissa. Tämän työn teoriaosuudessa tarkastellaan RFID-tekniikkaa ja sen komponentteja sekä niiden hyödyntämistä eri sektoreilla ja logistiikassa. Työn empiirisessä osuudessa selvitetään, mitkä ovat puolustusvoimien tarpeet RFID:n käytöllä ja vaatimuksia ensihoidon kiireellisyysluokittelulle (TRIAGE) sekä materiaalihallinnon ja niiden kautta saatavalle tilannekuvalle. Työn tuloksena saadaan perusteita puolustusvoimien RFID-ratkaisujen suunnittelun pohjaksi.

Determining risk potential through accidents and near-accidents: an empirical study in a steel factory

Fatal and permanently disabling accidents form only one per I cent of all occupational accidents but in many branches of industry they account for more than half the accident costs. Furthermore the human suffering of the victim and his family is greater in severe accidents than in slight ones. For both human and economic reasons the severe accident risks should be identified befor injuries occur. It is for this purpose that different safety analysis methods have been developed . This study shows two new possible approaches to the problem.. The first is the hypothesis that it is possible to estimate the potential severity of accidents independent of the actual severity. The second is the hypothesis that when workers are also asked to report near accidents, they are particularly prone to report potentially severe near accidents on the basis of their own subjective risk assessment. A field study was carried out in a steel factory. The results supported both the hypotheses. The reliability and the validity of post incident estimates of an accident's potential severity were reasonable. About 10 % of accidents were estimated to be potentially critical; they could have led to death or very severe permanent disability. Reported near accidents were significantly more severe, about 60 $ of them were estimated to be critical. Furthermore the validity of workers subjective risk assessment, manifested in the near accident reports, proved to be reasonable. The studied new methods require further development and testing. They could be used both in routine usage in work places and in research for identifying and setting the priorities of accident risks.

Merchandising Strategies and Retail Performance for Seasonal Fashion Products

This study presents mathematical methods for evaluation of retail performance with special regard to product sourcing strategies. Forecast accuracy, process lead time, offshore / local sourcing mix and up front / replenishment buying mix are defined as critical success factors in connection with sourcing seasonal products with a fashion content. As success measures, this research focuses on service level, lost sales, product substitute percentage, gross margin, gross margin return on inventory and mark down rate. The accuracy of demand forecast is found to be a fundamental success factor. Forecast accuracy depends on lead time. Lead times are traditionally long and buying decisions are made seven to eight months prior to the start of the selling season. Forecast errors cause stockouts and lost sales. Some of the products bought for the selling season will not be sold and have to be marked down and sold at clearance, causing loss of gross margin. Gross margin percentage is not the best tool for evaluating sourcing decisions and in the context of this study gross margin return on inventory, which combines profitability and assets management, is used. The findings of this research suggest that there are more profitable ways of sourcing products than buying them from low cost offshore sources. Mixing up front and inseason replenishment deliveries, especially when point of sale information is used for improving forecast accuracy, results in better retail performance. Quick Response and Vendor Managed Inventory strategies yield better results than traditional up front buying from offshore even if local purchase prices are higher. Increasing the number of selling seasons, slight over buying for the season in order to

Performance Improvement of Centrifugal Compressor Stage with Pinched Geometry or Vaned Diffuser

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.

Sinfonia piccola

Soitinnus: Ork.

Mestarin nuuskarasia

Digitoitu 21. 8. 2008.

Kaarle Kuninkaan metsästys

Digitoitu 29. 12. 2008

Hoffmannin kertomukset

Esityskieli: suomi.

Juha

Digitoitu 11. 10. 2007.

Jazz : Sibelius-Akatemian Jazzstudio

Digitoitu 15. 10 2008.