Patologias na formulação de um betão na ilha da Madeira

Existem diversos métodos de formular a composição de um betão, dos quais, este estudo realça a metodologia aplicada às curvas de referência, nomeadamente a de Faury. No âmbito desta dissertação, o estudo do betão foi focado nas propriedades da resistência à compressão e trabalhabilidade, e nos factores que as influenciam para a obtenção dos resultados pretendidos. A dificuldade deste estudo surgiu na obtenção da trabalhabilidade desejada, derivada do tipo de agregados existentes na empresa e incertezas na quantificação da água de amassadura. Esta foi analisada, com especial destaque, para os parâmetros de absorção e humidade, em que o ensaio normativo da obtenção da capacidade de absorção dos agregados, poderá não ser o mais indicado para quantificar o valor real deste parâmetro. Notou-se que o método de Faury para determinar a água de amassadura, não era o mais indicado, por não ter em conta os parâmetros anteriormente referidos. Foram realizados diversos ensaios de obtenção de parâmetros necessários para efectuar uma formulação acertada. Foram também realizadas diversas amassaduras, com composições distintas, de forma a analisar a sua influência nos resultados. Estes foram analisados através de critérios de conformidade, para classificação do betão em termos de resistência. Foi possível concluir que os resultados da formulação da composição do betão, dependem muito da qualidade dos agregados utilizados, como a sua forma, porosidade e homogeneidade do material pétreo. De acordo com os resultados experimentais, foi concluída a existência de uma insuficiência de finos nas composições criadas para o betão, sugerindo uma curva real granulometria de referência para potencializar a trabalhabilidade para o tipo de agregados utilizados neste estudo.

Medidas de concordância para variáveis categorizadas

Apesar desta tese se propor abordar exclusivamente variáveis categorizadas e medidas que descrevem a relação entre estas variáveis, consideramos extremamente relevante estender ao caso em que uma das variáveis em estudo de uma variável contínua. Tais medidas, quando usadas corretamente, fornecem uma descrição útil da estrutura implícita numa tabela de contingência. Ao longo dos anos, muitos cientistas deduziram medidas de associação de acordo com o que se propunham avaliar. Perante um conjunto tão variado de medidas, o nosso objetivo foi sumarizá-las, classificá-las em grupos mais gerais e estabelecer em que situações de que a sua utilização é indicada. Apesar de estarmos interessados em avaliar a concordância, realizámos que era essencial incluir nesta tese os testes de ajustamento e a análise de tabelas de contingência.

O golfe enquanto meio de compreensão e transformação do indivíduo

Cada vez mais, o fenómeno desportivo é suportado pelo conhecimento de um conjunto de disciplinas científicas que, quando devidamente articuladas sob um quadro de complexidade coerente, promovem um melhor entendimento acerca das mudanças que ocorrem no indivíduo. Neste sentido, através da realização do presente trabalho, procurámos perceber qual o enquadramento conferido ao golfe e se esse enquadramento é compatível com a ideia de o golfe servir de ferramenta para a compreensão e transformação do indivíduo. Para isso, através da literatura existente, procurámos conhecer quais as suas origens e evolução, de que forma está caracterizado (conceitos e opiniões dos diferentes agentes desportivos), qual a sua expressão (ao nível dos diferentes mercados) e que tipo de estudos e investigações existentes (focados no jogador) apoiam a sua evolução. De seguida, realizámos o enquadramento do golfe à luz da Taxonomia das Actividades Desportivas de Fernando Almada e analisámos o swing com base no Modelo Taxonómico dos Desportos Individuais. Como forma de testar a conjectura de que o golfe pode servir para a compreensão e transformação do indivíduo, realizámos uma situação experimental com um grupo de 14 jogadores (com handicaps compreendidos entre 5 e 32) de forma a perceber se existiam diferenças significativas no seu desempenho (p _ 0,05), quando expostos a diferentes condições (uma condição confortável e a uma condição de desconfortável). Os resultados globais (da amostra) não evidenciaram diferenças significativas, ao contrário de alguns dos resultados individuais, que por sua vez, permitiram estabelecer ligações com as diferentes variáveis funcionais inerentes à realização do swing,possibilitando-nos a formulação de um conjunto de hipóteses que poderão servir de orientação à compreensão de algumas das características mais marcantes do jogador.

Caracterização, simulação (à escala) e modelação do escoamento em canais artificiais: aplicação a caso de estudo

Os escoamentos no interior de zonas urbanas, apresentam grande heterogeneidade, pelo que a sua caracterização, requer uma formulação que incorpore explicitamente essa variabilidade espacial. A caracterização, simulação (à escala) e modelação do escoamento em canais artificiais e a aplicação a um caso de estudo, no Laboratório de Hidráulica da UMa, representa o cerne desta dissertação. Os objetivos principais desta dissertação são: a caracterização e desenvolvimento de ferramentas de simulação do comportamento do escoamento em canais artificiais, no caso de uma variação súbita dos caudais afluentes, mecanismos de prevenção de cheia; o desenvolvimento de um modelo de simulação hidrodinâmico, considerando os escoamentos variáveis em superfície livre no caso de situações de cheia, na simulação entre as condições variáveis das afluências, das condições hidromorfológicas do canal e da instalação e operação dos sistemas e regulação dos escoamentos; e ainda a análise da viabilidade da simulação (modelo) na gestão e prevenção de cheias em canais artificiais. Numa primeira instância, procede-se à recolha de toda a informação bibliográfica disponível. Com recurso aos modelos digitais do terreno e ao programa ArcGis, é efetuada toda uma exaustiva caracterização da bacia hidrográfica, relativa ao caso de estudo (canal artificial), a partir da qual foi possível obter os dados inerentes às características geométricas, características de relevo e características de drenagem. Segue-se a análise da precipitação com recurso a folhas de cálculo e dados fornecidos pelas instituições pertinentes, de forma a obter valores de precipitação média diária e anual para aplicação de fórmulas, tanto para calcular valores de tempo de concentração, bem como caudais. O próximo passo é selecionar os troços relevantes do canal em estudo e com recurso ao equipamento disponível no Laboratório de Hidráulica da UMa, à folha de cálculo programada e ao programa HEC-RAS procede-se à simulação/modelação/análise desses troços, comparando o resultado/comportamento simulado, com o expectável e entre os vários métodos. Por fim, são expostas as conclusões, bem como algumas considerações finais e uma listagem de objetivos a manter ou alcançar nos próximos anos, onde se incluem, ações prioritárias e recomendações visando, não só melhorar o processo de caracterização do escoamento em canais artificiais, bem como simplificar a prevenção e gestão de cheias.

Qualificação de edifícios residenciais verticais em Natal/RN à luz do regulamento técnico da qualidade para o nível de eficiência energética de edificações residenciais (RTQ-R)

The goal of the research was to investigate the energy performance of residential vertical buildings envelope in the hot and humid climate of Natal, capital of Rio Grande do Norte, based in the Technical Regulation of Quality for Energy Efficiency Level in Residential Buildings (RTQ -R), launched in 2010. The study pretends to contribute to the development of design strategies appropriate to the specific local climate and the increasing of energy efficiency level of the envelope. The methodological procedures included the survey in 22 (twenty two) residential buildings, the formulation of representative prototypes based on typological and constructives characters researched and the classification of the level of energy efficiency in the envelopment of these prototypes, using as a tool the prescriptive method of the RTQ-R and the parametric analyzes from assigning different values of the following variables: shape of the pavement type; distribution of housing compartments; orientation of the building; area and shading of openings; thermal transmittance, and solar absorptance of opaque materials of the frontage in order to evaluate the influence of these on the envelopment performance. The main results accomplished with this work includes the qualification of vertical residential buildings in Natal/RN; the verification of the adequacy of these buildings to local climate based from the diagnosis of the thermal energy of the envelopment performance, the identification of variables with more significant influence on the prescriptive methodology of RTQ-R and design solutions more favorable to obtain higher levels energy efficiency by this method. Finally, it was verified, that some of these solutions proved contradictory in relation to the recommendations contained in the theoretical approaches regarding environmental comfort in hot and humid weather, which indicates the need for improvement of the prescriptive method RTQ-R and further research on efficient design solutions

Influência de variáveis arquitetônicas no desempenho energético de hotéis no clima quente e úmido da cidade de Natal/RN

This master thesis aims to assess the influence of the design decisions on the energy building performance of hotels. The research is based on the integration of field study and computer simulation. Firstly, a detailed field study is carried out to identify the characteristics of hotels in Natal, Rio Grande do Norte. The items assessed are occupancies, light and equipment densities, types of air conditioning, total and monthly energy consumption, among others. A second and more comprehensive field study is carried out to identify the range of occurrence of architectural variables, with a larger number of buildings. A base case is modelled in VisualDOE, based on the first field study. Then, a first set of simulations are run to explore the sensitivity of the variables on the energy consumption. The results analyses were the base of a second set of simulations, which combined the most influential variables. The results of 384 models were assessed, and the impacts of design decisions were quantified. The study discusses tendencies and recommendations, as well as the methods advantages and disadvantages

Formulação e caracterização de matérias-primas para revestimento cerâmico Semi-Poroso com adição de chamote de telhas

The ceramics industry in Piauí is nowadays with 55 industries where 11 are in Teresina which is the mainstream of the state, producing 55 million shingles; in which 10 % is of this production is wasted being sometimes thrown on the margins of rivers, roads and highways provoking an environmental degradation. The main goal of this work is to verify the potential of producing semi porous ceramic using grog of shingles, on the first part of this work bodies-of-proof were produced from a basic formula of an industry, doping it with 5 %, 10 %, 15 % and 20 % in mass and in the second part of this work some bodies-of-proof were produced from a formula where one raw material was substituted by 50 % of grog and another substituting it all by grog, bodies-of-proof made of a basic formula previously announced was used for experiment control.The grog and the raw materials were characterized by: particle size analysis , thermal differential analysis, X ray diffraction , X ray fluorescence, an thermal gravimetric analysis and rational analyses. The bodies-of-proof were sintetisized in an industrial oven obeying the normal cycle adopted by an industry, with peak temperatures of 1135 oC and a fast burning cycle of 25 minutes having as energetic fuel liquefied petroleum gas . The pieces that were obtained by this were submersed in rehearsed physics of: water absorption of, apparent specific mass, apparent porosity, lineal retraction, rupture tension to the flexural and dilatometry; mineralogical analysis for X ray diffraction; and microstructural for electronic microscope of sweeping. For all the formulas with addition of grog, superior priorities to the requested by the requirements for semi porous and for the formula to F2-2,5 superior priorities to standard formulas which justifies the incorporation of the shingles in mass for the semi porous ceramic

Estudo da adição de argila expandida na formulação de concretos leves

Lightweight concrete has been the subject of several studies towards the development of new building materials. Emphasis has been given on the particle size effect and nature of aggregates used as raw materials. The present study includes an analysis of the materials that make this kind of concrete, analyzes of mechanical properties such as compressive and tensile strength, in addition to assessments of the interface concrete aggregate/matrix interface, porosity and absorption profile of chloride ions in lightweight concrete based on expanded clay. The experiments were carried out by molding cylindrical samples 100 mm in diameter and 200 mm in height. The dosage experiments were performed without additives or with the addition of minerals: (T1) 1: 2.01: 1.10: 0.78 (T2) 1: 2.00: 1.32 : 0.62 - (T3) 1 :1.93 :1.54: 0.47 (cement : sand : expanded clay 0500 : expanded clay 1506).The water to cement ratio was set to 0.43. Expanded clay minerals with different average particle sizes were used, i.e., 9.5 mm/0500 and 19 mm/1506. The larger aggregate was coated by a glassy layer, yielding lower water absorption characteristics to the concrete. The results showed that the use of light expanded clay aggregates is a technically interesting solution to the production of lightweight concrete for construction applications

Aproveitamento de resíduos minerais na formulação de argamassas para a construção civil

Current environmental concerns include the excessive consumption and inefficient use of non-renewable natural resources. The construction industry is considered one of the largest consumers of natural raw materials, significantly contributing to the environmental degradation of the planet. The use of calcareous quarry (RPPC) and porcelain tile polishing residues (RPP) as partial replacements of the cement in mortars is an interesting alternative to minimize the exploration of considerably large amounts of natural resources. The present study aimed at investigating the properties of fresh and hardened mortars produced using residues to replace cement. The residues used were fully characterized to determine their specific mass, unitary mass, particle size distribution and morphology, and composition. The performance of the mortars was compared to that of reference compositions, prepared without residues. A total of 18 compositions were prepared, 16 using residues and 2 reference ones. The mortars were prepared using Portland CP II F 32 cement, CH I hydrated lime, river sand and tap water. The compositions of the mortars were 1:1:6 and 1:0.5:4.5 (vol%), and water to cement ratios of 1.87 and 1.45 were used, respectively. The mortars in the fresh state were evaluated by consistency index, water retention, density of mass and incorporated air content tests. In their hardened state, the mortars were evaluated by apparent mass density, modulus of elasticity, flexural tensile strength, compressive strength and water absorption by capillarity. The mortars were also analyzed by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and fluorescence. Finally, they were classified according to NBR 13281 standards. The mortars prepared using residues partially replacing the cement exhibited lower modulus of elasticity compared to the reference compositions, thus improving the performance in their intended use. On the downside, the water absorption by capillarity was affected by the presence of residues and both the tensile and compressive strength were reduced. However, from the overall standpoint, the replacement of cement by calcareous quarry or porcelain tile polishing residues did not result in significant changes in the properties of the mortars. Therefore, compositions containing these residues can be used in the construction industry

Formulação de pastas cimentícias com adição de suspensões de quitosana para cimentação de poços de petróleo

Primary cementing is one of the main operations in well drilling responsible for the mechanical stability and zonal isolation during the production of oil. However, the cement sheath is constantly under mechanical stresses and temperature variations caused by the recovery of heavy oil. In order to minimize fracture and wear of the cement sheath, new admixtures are developed to improve the properties of Portland cement slurries and avoid environmental contamination caused by leaking gas and oil. Polymers with the ability to form polymeric films are candidates to improve the properties of hardened cement slurries, especially their fracture energy. The present study aimed at evaluating the effect of the addition of a chitosan suspension on cement slurries in order to improve the properties of the cement and increase its performance on heavy oil recovery. Chitosan was dissolved in acetic ac id (0.25 M and 2 M) and added to the formulation of the slurries in different concentrations. SEM analyses confirmed the formation of polymeric films in the cementitious matrix. Strength tests showed higher fracture energy compared to slurries without the addition of chitosan. The formation of the polymeric films also reduced the permeability of the slurry. Therefore, chitosan suspensions can be potentially used as cementing admixtures for heavy oil well applications

Formulação de grautes leves para a cimentação de poços de petróleo onshore

Grautes are dry mixes with hydraulic characteristics widely used in construction. This material comprises cement, mineral additives and dosed in accordance with the desired properties. The use of grautes in cementing oil wells potentially increases the precision in the composition of the mixture, since it is requires only the addition of the mixing water before its pumping. Such benefit may be availed in cementing wells since the formulations grautes meet the temperature and pressure characteristics typical of wells. The objective of this study is to evaluate the effect of adding different percentages of industrial minerals properties of light grautes for onshore oil wells. For the formulation of the employees were grautes light industrial minerals and waste minerals abundant in the Northeast, in addiction to Portland cement and chemical additives Special class. Grautes were formulated with densities between 1.55 g/cm3 (13.0 lb/gal) and 1.68 g/cm3 (14 lb/gal). Tests results showed that grautes with higher density in the range studied meet the specifications for cementation of shallow wells onshore. The compositions lighter can also be adjusted for applying the material in the cementation of oil wells

Efeito da adição de carbonatos em formulação de massa para revestimento cerâmico utilizando matérias-primas do Piauí

Piauí state is a major producer of traditional red ceramic burning as bricks, tiles and ceramic tiles, with its main production center located in the city of Teresina. The state has large reserves of raw materials that can be used in the ceramic coating as clays, quartz, talc and carbonates. However, in the preparation of ceramic bodies using only a mixture of clays with different characteristics. The study aims to evaluate the effect of adding two types of carbonates in the ceramic semiporous mass coating produced in Piauí and then to verify the potential use of these carbonates as supplementary raw material product manufactured or the feasibility of obtaining a ceramic plate that meets the specifications for the porous coating. For this, were characterized the ceramic Piauí coating mass, a calcitic carbonate and a dolomitic, were made in the levels of 2, 4, 8, 16, and 32%. The masses were formed by pressing and burneds in two environments: a laboratory furnace (1080°C, 1120°C, 1140°C, and 1160°C) and an industrial furnace (1140°C). Then, following tests of linear shrinkage water absorption, apparent porosity, bulk density and flexural strength. Furthermore, the fired specimens were tested for their macrostructure and microstructure. The results showed the possibility of using the carbonate in ceramic mass flooring produced in Piauí, as added in small proportions improved dimensional stability and increased mechanical strength of ceramics pieces. It also proved itself possible to produce porous coating when added in higher levels

Efeito das variáveis laboratoriais protéticas na adesão da porcelana com ligas de níquel-cromo

The metalceramic crowns are usually used in dentistry because they provide a resistant structure due to its metallic base and its aesthetics from the porcelain that recovers this structure. To manufacture these crowns, a series of stages should be accomplished in the prosthetic laboratories, and many variables can influence its success. Changes in these variables cause alterations in the metallic alloy and in the porcelain, so, as consequence, in the adhesion between them. The composition of the metal alloy can be modified by recasting alloys, a common practice in some prosthetic laboratories. The aim of this paper is to make a systematic study investigating metalceramic crowns as well as analyzing the effect of recasting Ni-Cr alloys. Another variable which can influence the mechanism of metalceramic union is the temperature used in firing porcelain procedure. Each porcelain has to be fired in a fixed temperature which is determined by the manufacturer and its change can cause serious damages. This research simulate situations that may occur on laboratory procedures and observe their consequences in the quality of the metalceramic union. A scanning eletron microscopy and an optic microscopy were accomplish to analyse the metal-ceramic interface. No differences have been found when remelting alloys were used. The microhardness were similar in Ni-Cr alloys casted once, twice and three times. A wettability test was accomplished using a software developed at the Laboratório de Processamento de Materiais por Plasma, on the Universidade Federal do Rio Grande do Norte. No differences were found in the contact angle between the solid surface (metallic substratum) and the tangencial plane to the liquid surface (opaque). To analyse if the temperature of porcelain firing procedure could influence the contact area between metal and porcelain, a variation in its final temperature was achieve from 980° to 955°C. Once more, no differences have been found

Estudo da adição de resíduo de scheelita em matriz cerâmica: formulação, propriedades físicas e microestrutura

Extractivism mineral is considered an activity highly degrading, due to the large volume of material that he moves in the form of ore and residues. The vast majority of mining companies do not show any technology or economically viable application that will allow the recycling of mineral residue, these being launched in areas receiving located the "open skies" degrade the environment. In Rio Grande do Norte to the production of ceramic red restricts their activities to the production of products such as: solid bricks, ceramic blocks, tiles, among others. Seeking to unite experiences and technical information that favor sustainable development, with important benefits to the construction sector and civil society in general, the present work studies the incorporation of the residue of scheelite in ceramic matrix kaolinitic, coming from the municipality of Boa Saúde - RN, in percentage of 5 %, 10 %, 20 %, 30% 40% and 50 %, by evaluating its microstructure, physical properties and formulation. The raw materials were characterized through the trials of X ray fluorescence, Diffraction of X rays, Differential Thermal Analysis and Termogravimetric Analysis. The samples were formed and fired at temperatures of 850o, 900o, 1000o, 1050o, 1100o, 1150o and 1200 oC, with isotherm of 1 hour and heating rate of 10 oC/min. Assays were performed technological of loss to fire, Water Absorption, Apparent Porosity, Apparent Density, Mass Loss in Fire and Bending Resistance; in addition to the Scanning Electron Microscopy, analyzing their physical and mechanical properties. The use of residue of scheelite in ceramic mass kaolinitic provided a final product with technological properties that meet the technical standards for the production of bricks and roofing tiles, with the percentage of 20% of waste that showed the best results