A New Indirect Electroanalytical Method to Monitor the Contamination of Natural Waters with 4-Nitrophenol Using Multiwall Carbon Nanotubes

The electrochemical detection of the hazardous pollutant 4-nitrophenol (4-NP) at low potentials, in order to avoid matrix interferences, is an important research challenge. This study describes the development, electrochemical characterization and utilization of a multiwall carbon nanotube (MWCNT) film electrode for the quantitative determination of 4-NP in natural water. Electrochemical impedence spectroscopy measurements showed that the modified surface exhibits a decrease of ca. 13 times in the charge transfer resistance when compared with a bare glassy carbon (GC) surface. Voltammetric experiments showed the possibility to oxidize a hydroxylamine layer (produced by the electrochemical reduction of 4-NP on the GC/MWNCT surface) in a potential region which is approximately 700 mV less positive than that needed to oxidize 4-NP, thus minimizing the interference of matrix components. The limit of detection for 4-NP obtained using square-wave voltammetry (0.12 mu mol L(-1)) was lower than the value advised by EPA. A natural water sample from a dam located in Sao Carlos (Brazil) was spiked with 4-NP and analyzed by the standard addition method using thee GC/MWCNT electrode, without any further purification step. the recovery procedure yielded a value of 96.5% for such sample, thus confirming the suitability of the developed method to determine 4-NP in natural water samples. The electrochemical determination was compared with that obtained by HPLC with UV-vis detection.

Electrocombustion of humic acid and removal of algae from aqueous solutions

This paper reports experiments involving the electrochemical combustion of humic acid (HA) and removal of algae from pond water. An electrochemical flow reactor with a boron-doped diamond film anode was used and constant current experiments were conducted in batch recirculation mode. The mass transfer characteristics of the electrochemical device were determined by voltammetric experiments in the potential region of water stability, followed by a controlled current experiment in the potential region of oxygen evolution. The average mass transfer coefficient was 5.2 x 10(-5) m s(-1). The pond water was then processed to remove HA and algae in the conditions in which the reaction combustion occurred under mass transfer control. To this end, the mass transfer coefficient was used to estimate the initial limiting current density applied in the electrolytic experiments. As expected, all the parameters analyzed here-solution absorbance at 270 nm, total phenol concentration and total organic carbon concentration-decayed according to first-order kinetics. Since the diamond film anode successfully incinerated organic matter, the electrochemical system proved to be predictable and programmable.

The electrochemical effect of acid functionalisation of carbon nanotubes to be used in sensors development

The electrochemical behaviour of multi-walled carbon nanotubes was compared with that of glassy carbon, and the differences were investigated by cyclic voltammetry and electrochemical impedance spectroscopy before and after acid pre-treatment. The electrochemical techniques showed that acid functionalisation significantly improves the electrocatalytic properties of carbon nanotubes. These electrocatalytic properties enhance the analytical signal, shift the oxidation peak potential to a less positive value, and the charge-transfers rate increase of both dopamine and K(4)[Fe(CN)(6)]. The functionalisation step and the resulting appearance of edge planes covered with different chemical groups were confirmed by FTIR measurements. Carbon nanotubes after acid pre-treatment are a potentially powerful analytical tool for sensor development. (C) 2010 Elsevier B.V. All rights reserved.

Ethanol oxidation reaction on PtCeO(2)/C electrocatalysts prepared by the polymeric precursor method

This paper presents a study of the electrocatalysis of ethanol oxidation reactions in an acidic medium on Pt-CeO(2)/C (20 wt.% of Pt-CeO(2) on carbon XC-72R), prepared in different mass ratios by the polymeric precursor method. The mass ratios between Pt and CeO(2) (3:1, 2:1, 1:1, 1:2, 1:3) were confirmed by Energy Dispersive X-ray Analysis (EDAX). X-ray diffraction (XRD) structural characterization data shows that the Pt-CeO(2)/C catalysts are composed of nanosized polycrystalline non-alloyed deposits, from which reflections corresponding to the fcc (Pt) and fluorite (CeO(2)) structures were clearly observed. The mean crystallite sizes calculated from XRD data revealed that, independent of the mass ratio, a value close to 3 nm was obtained for the CeO(2) particles. For Pt, the mean crystallite sizes were dependent on the ratio of this metal in the catalysts. Low platinum ratios resulted in small crystallites. and high Pt proportions resulted in larger crystallites. The size distributions of the catalysts particles, determined by XRD, were confirmed by Transmission Electron Microscope (TEM) imaging. Cyclic voltammetry and chronoamperometic experiments were used to evaluate the electrocatalytic performance of the different materials. In all cases, except Pt-CeO(2)/C 1:1, the Pt-Ceo(2)/C catalysts exhibited improved performance when compared with Pt/C. The best result was obtained for the Pt-CeO(2)/C 1:3 catalyst, which gave better results than the Pt-Ru/C (Etek) catalyst. (C) 2009 Elsevier B.V. All rights reserved.

Electrochemical determination of the antioxidant capacity: The ceric reducing/antioxidant capacity (CRAC) assay

The CRAC assay is a direct electron transfer test of antioxidant capacity for several organic compounds. The ability of eight different compounds in reducing Cc 41 was studied by chronoamperometric measurements of the remaining Ce(3+) species. The following antioxidant classification was observed: tannic acid >> quercetin > rutin > gallic acid approximate to catechin > ascorbic acid > BHA > Trolox. These results agree with others already published and a good correlation (R(2) = 0.937) was found with the classical spectrophotometric FRAP assay. The CRAC assay is simple, fast, free from sample pretreatment and applicable to nontransparent samples.

Effect of the catalyst composition in the Pt-x(Ru-Ir)(1-x)/C system on the electro-oxidation of methanol in acid media

The effect of variations in the composition for ternary catalysts of the type Pt-x(Ru-Ir)(1-x)/C on the methanol oxidation reaction in acid media for x values of 0.25, 0.50 and 0.75 is reported. The catalysts were prepared by the sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic absorption spectroscopy (AAS) and energy dispersive X-ray (EDX) analyses. The nanometric character (2.8-3.2 nm) of the sol-gel deposits was demonstrated by XRD and TEM while EDX and AAS analyses showed that the metallic ratio in the compounds was very near to the expected one. Cyclic voltammograms for methanol oxidation revealed that the reaction onset occur at less positive potentials in all the ternary catalysts tested here when compared to a Pt-0.75-Ru-0.25/C (E-Tek) commercial composite. Steady-state polarization experiments (Tafel plots) showed that the Pt-0.25(Ru-Ir)(0.75)/C catalyst is the more active one for methanol oxidation as revealed by the shift of the reaction onset towards lower potentials. In addition, constant potential electrolyses suggest that the addition of Ru and Ir to Pt decreases the poisoning effect of the strongly adsorbed species generated during methanol oxidation. Consequently, the Pt-0.25 (Ru-Ir)(0.75)/C Composite catalyst is a very promising one for practical applications. (c) 2007 Elsevier B.V. All rights reserved.

Synthesis, Characterization, and Electrocatalytic Activity toward Methanol Oxidation of Carbon-Supported Pt(x)-(RuO(2)-M)(1-x) Composite Ternary Catalysts (M = CeO(2), MoO(3), or PbO(x))

Carbon-supported platinum is commonly used as an anode electrocatalyst in low-temperature fuel cells fueled with methanol. The cost of Pt and the limited world supply are significant barriers for the widespread use of this type of fuel cell. Moreover, Pt used as anode material is readily poisoned by carbon monoxide produced as a byproduct of the alcohol oxidation. Although improvements in the catalytic performance for methanol oxidation were attained using Pt-Ru alloys, the state-of-the-art Pt-Ru catalyst needs further improvement because of relatively low catalytic activity and the high cost of noble Pt and Ru. For these reasons, the development of highly efficient ternary platinum-based catalysts is an important challenge. Thus, various compositions of ternary Pt(x)-(RuO(2)-M)(1-x)/C composites (M = CeO(2), MoO(3), or PbO(x)) were developed and further investigated as catalysts for the methanol electro-oxidation reaction. The characterization carried out by X-ray diffraction, energy-dispersive X-ray analysis, transmission electron microscopy, X-ray photoelectron spectroscopy, and cyclic voltammetry point out that the different metallic oxides were successfully deposited on the Pt/C, producing small and well-controlled nanoparticles in the range of 2.8-4.2 nm. Electrochemical experiments demonstrated that the Pt(0.50)(RuO(2)-CeO(2))(0.50)/C composite displays the higher catalytic activity toward the methanol oxidation reaction (lowest onset potential of 207 mV and current densities taken at 450 mV, which are 140 times higher than those at commercial Pt/C), followed by the Pt(0.75)(RuO(2)-MoO(3))(0.25)/C composite. In addition, both of these composites produced low quantities of formic acid and formaldehyde when compared to a commercially available Pt(0.75)-Ru(0.25)/C composite (from E-Tek, Inc.), suggesting that the oxidation of methanol occurs mainly by a pathway that produces CO(2) forming the intermediary CO(ads).

Carbon supported electrocatalysts prepared by the sol-gel method and their utilization for the oxidation of methanol in acid media

One of the key objectives in fuel-cell technology is to improve the performance of the anode catalyst for the alcohol oxidation and reduce Pt loading. Here, we show the use of six different electrocatalysts synthesized by the sol -gel method on carbon powder to promote the oxidation of methanol in acid media. The catalysts Pt-PbO(x) and Pt-(RuO(2)-PbO(x)) with 10% of catalyst load exhibited significantly enhanced catalytic activity toward the methanol oxidation reaction as compared to Pt-(RuO(2))/C and Pt/C electrodes. Cyclic voltammetry studies showed that the electrocatalysts Pt-PbO(x)/C and Pt-(RuO(2)-PbO(x))/C started the oxidation process at extremely low potentials and that they represent a good novelty to oxidize methanol. Furthermore, quasi-stationary polarization experiments and cronoamperometry studies showed the good performance of the Pt-PbO(x), Pt-(RuO(2)-PbO(x))/C and Pt-(RuO(2)-IrO(2))/C catalysts during the oxidation process. Thus, the addition of metallic Pt and PbO(x) onto high-area carbon powder, by the sol -gel route, constitutes an interesting way to prepare anodes with high catalytic activity for further applications in direct methanol fuel cell systems.

Mechanical and tribological properties of PVD-coated cemented carbide as evaluated by a new multi-pass scratch testing method

A new test method based on multipass scratch testing has been developed for evaluating the mechanical and tribological properties of thin, hard coatings. The proposed test method uses a pin-on-disc tribometer and during testing a Rockwell C diamond stylus is used as the “pin” and loaded against the rotating coated sample. The influence of normal load on the number of cycles to coating damage is investigated and the resulting coating damage mechanisms are evaluated by posttest scanning electron microscopy. The present study presents the test method by evaluating the performance of Ti0.86Si0.14N, Ti0.34Al0.66N, and (Al0.7Cr0.3)2O3 coatings deposited by cathodic arc evaporation on cemented carbide inserts. The results show that the test method is quick, simple, and reproducible and can preferably be used to obtain relevant data concerning the fatigue, wear, chipping, and spalling characteristics of different coating-substrate composites. The test method can be used as a virtually nondestructive test and, for example, be used to evaluate the fatigue and wear resistance as well as the cohesive and adhesive interfacial strength of coated cemented carbide inserts prior to cutting tests.

Designing a Remote Navigation System

This project involves the design and implementation of a global electronic tracking system intended for use by trans-oceanic vessels, using the technology of the U.S. Government's Global Positioning System (GPS) and a wireless connection to a networked computer. Traditional navigation skills are being replaced with highly accurate electronics. GPS receivers, computers, and mobile communication are becoming common among both recreational and commercial boaters. With computers and advanced communication available throughout the maritime world, information can be shared instantaneously around the globe. This ability to monitor one's whereabouts from afar can provide an increased level of safety and efficiency. Current navigation software seldom includes the capability of providing upto-the-minute navigation information for remote display. Remote access to this data will allow boat owners to track the progress of their boats, land-based organizations to monitor weather patterns and suggest course changes, and school groups to track the progress of a vessel and learn about navigation and science. The software developed in this project allows navigation information from a vessel to be remotely transmitted to a land-based server, for interpretation and deployment to remote users over the Internet. This differs from current software in that it allows the tracking of one vessel by multiple users and provides a means for two-way text messaging between users and the vesseI. Beyond the coastal coverage provided by cellular telephones, mobile communication is advancing rapidly. Current tools such as satellite telephones and single-sideband radio enable worldwide communications, including the ability to connect to the Internet. If current trends continue, portable global communication will be available at a reasonable price and Internet connections on boats will become more common.

Estudo exploratório da deposição de filmes de diamante em alguns substratos cerâmicos

o presente trabalho é um estudo exploratório a respeito da síntese de filmes de diamante via deposiçãoquímica a vapor (CVD) sobre alguns substratos cerâmicos: diboreto de titânio (TiB2), ítria (Y20a), zircão (ZrSi04), zircônia parcialmente e totalmente estabilizada com ítria (Zr02), pirofilita ( Al2Si4OlO(OHh), .alumina (Al2Oa) e nitreto de boro hexagonal (h-BN). Estes substratos foram produzidos, em sua maioria, a partir da sinterização de pós micrométricos em altas temperaturas. Além do estudo em relação a possíveis candidatos alternativos ao tradicional silício para o crescimento de filmes auto-sustentáveis, procuramos encontrar substratos onde o filme aderisse bem e cujas propriedades tribológicas pudessem ser melhoradas com o recobrimento com filme de diamante.Dentre os materiais selecionados, constatamos que a topografia da superfície relacionada à densidade de contornos de grão, desempenha um papel relevante na nucleação do diamante. Além disso, os materiais que favorecem a formação de carbonetos conduziram a melhores resultados na nucleação e crescimento do filme, indicando que a ação da atmosfera reativa do CVD com o substrato também contribui decisivamente para o processo de nucleação. A partir dos resultados obtidos, concluímos que a aderência do filme de diamante ao zircão é excelente, assim como a qualidade do filme, o que pode serexplorado convenientemente caso as propriedades mecânicas do sinterizado de zircão sejam adequadas. No caso da zircônia parcialmente estabilizada, os resultados obtidos foram surpreendentes e este material poderia substituir o convencional substrato de silício para a deposição de filmes auto-sustentados de diamante, com inúmeras vantagens, dentre elas o fato de ser reutilizável e de não ser necessário ataque com ácidos para remoção do substrato, o que evita a geração de resíduos químicos.

Previdência social em três modelos novo-clássicos

propósito deste trabalho estudar as implicações econômicas da previdência social no contexto do mais amplamente difundido modelo de gerações superpostas (OLG), construído por Paul Samuelson (1958) complementado por Peter Diamond (1965) exemplifica-las mediante simulações. Para tanto, serão utilizadas três versões destes modelos, do próprio Diamond (1965), de Robert Barro (1974) de Marco Martins (1995), as quais se diferenciam pela maneira como cada uma delas incorpora demanda por capital dos agentes. Serão examinados em especial os efeitos da previdência sobre acumulação de capital sobre bem-estar da sociedade.

Enriching information to prevent bank runs

Sequential service in the banking sector, as modeled by Diamond and Dybvig (1983), is a barrier to full insurance and potential source of financial fragility against which deposit insurance is infeasible (Wallace, 1988). In this paper, we pursue a different perspective, viewing the sequence of contacts as opportunities to extract information through a larger message space with commitment to richer promises. As we show, if preferences satisfy a separating property then the desired elimination of dominated strategies (Green and Lin, 2003) occurs even when shocks are correlated. In this manner the sequential service promotes stability.

A assimetria funcional inter-hemisférica

A temática da assimetria funcional inter-hemisférica e analisada, neste trabalho, através de uma revisão crítica da literatura concernente aos estudos clínicos e experimentais (realizados tanto com pacientes neurológicos quanto com indivíduos normais) que se mostraram mais significativos para a configuração atual deste campo do saber. Inicialmente são analisados os estudos efetuados com pacientes neurológicos lesados unilateralmente, que forneceram as primeiras evidências sobre uma organização assimétrica dos hemisférios cerebrais. Na medida em que tal assimetria refere-se principalmente aos processos cognitivos, focalizou-se esta análise nos estudos mais significativos realizados sobre os quadros de afasias, apraxias, agnosias e amnésias, diretamente relacionados à problemática da assimetria cerebral. Os estudos empregando a técnica de Wada e com pacientes comissurotomizados foram abordados a seguir procurando-se evidenciar o grande avanço que propiciaram nos conhecimentos concernentes à assimetria funcional inter-hemisférica, quer em termos da caracterização funcional de cada hemisfério cerebral (o que acabou por levar a substituição da problemática de dominância cerebral pela de assimetria funcional inter-hemisférica) quer em termos da mobilização de interesse por esta área da pesquisa neuropsicológica. No que concerne aos estudos com indivíduos normais, procurou-se enfatizar a progressão de um enfoque centrado nas caracterizações hemisféricas para um enfoque centrado na análi¬se dos requerimentos cognitivos de uma determinada tarefa, com o objetivo de avaliar a participação relativa dos hemisférios cerebrais nas tarefas complexas. As diferenças individuais quanto ao padrão de lateralização funcional foram particularmente examinadas em relação aos estudos vinculados a variáveis comportamentais facilmente observáveis tais como a preferência manipulatória e sua história familiar, a preferência ocular e o sexo, dando-se ênfase a estudos correlacionais entre aquela primeira variável e a lateralização para a linguagem, que têm tido maior suporte empírico. Os principais modelos emergentes na literatura sobre a atuação conjunta dos hemisférios cerebrais, tentando explicar sua din5mica, foram objeto de um tópico ulterior. Dentre os diversos modelos propostos considerou-se mais consistente o de Dimond e Beaumont (Beaumont, 1974) que propõe uma atuação mais integrada entre os hemisférios cerebrais, embora não se revele totalmente satisfatório. Análises de questões filogenética, ontogenética e referentes aos diferentes processamentos cognitivos requeridos em tarefas complexas foram efetuadas já que constituem grande foco de interesse na literatura atual concernente à assimetria funcional inter-hemisférica.