An efficient and robust case sorting for algorithm for transient stability assessment

An efficient and robust case sorting algorithm based on Extended Equal Area Criterion (EEAC) is proposed in this paper for power system transient stability assessment (TSA). The time-varying degree of an equivalent image system can be deduced by comparing the analysis results of Static EEAC (SEEAC) and Dynamic EEAC (DEEAC), the former of which neglects all time-varying factors while the latter partially considers the time-varying factors. Case sorting rules according to their transient stability severity are set combining the time-varying degree and fault messages. Then a case sorting algorithm is designed with the “OR” logic among multiple rules, based on which each case can be identified into one of the following five categories, namely stable, suspected stable, marginal, suspected unstable and unstable. The performance of this algorithm is verified by studying 1652 contingency cases from 9 real Chinese provincial power systems under various operating conditions. It is shown that desirable classification accuracy can be achieved for all the contingency cases at the cost of very little extra computational burden and only 9.81% of the whole cases need to carry out further detailed calculation in rigorous on-line TSA conditions.

The high-energy environment in the super-Earth system CoRoT-7

High-energy irradiation of exoplanets has been identified to be a key influence on the stability of these planets' atmospheres. So far, irradiation-driven mass-loss has been observed only in two Hot Jupiters, and the observational data remain even more sparse in the super-Earth regime. We present an investigation of the high-energy emission in the CoRoT-7 system, which hosts the first known transiting super-Earth. To characterize the high-energy XUV radiation field into which the rocky planets CoRoT-7b and CoRoT-7c are immersed, we analyzed a 25 ks XMM-Newton observation of the host star. Our analysis yields the first clear (3.5σ) X-ray detection of CoRoT-7. We determine a coronal temperature of ≈ 3 MK and an X-ray luminosity of 3 × 1028 erg s-1. The level of XUV irradiation on CoRoT-7b amounts to ≈37 000 erg cm-2 s-1. Current theories for planetary evaporation can only provide an order-of-magnitude estimate for the planetary mass loss; assuming that CoRoT-7b has formed as a rocky planet, we estimate that CoRoT-7b evaporates at a rate of about 1.3 × 1011 g s-1 and has lost ≈4-10 earth masses in total.

Global Systemic Risk and International Regulatory Coordination: Squaring Sovereignty and Financial Stability

In recent years much attention has been given to systemic risk and maintaining financial stability. Much of the focus, rightly, has been on market failures and the role of regulation in addressing them. This article looks at the role of domestic policies and government actions as sources of global instability. The global financial system is built upon global markets controlled by national financial and macroeconomic policies. In this context, regulatory asymmetries, diverging policy preferences, and government failures add a further dimension to global systemic risk not present at the national level.
Systemic risk is a result of the interplay between two independent variables: an underlying trigger event, in this analysis a domestic policy measure, and a transmission channel. The solution to systemic risk requires tackling one of these variables. In a domestic setting, the centralization of regulatory power into one single authority makes it easier to balance the delicate equilibrium between enhancing efficiency and reducing instability. However, in a global financial system in which national financial policies serve to maximize economic welfare, regulators will be confronted with difficult policy and legal tradeoffs.
We investigate the role that financial regulation plays in addressing domestic policy failures and in controlling the danger of global financial interdependence. To do so we analyse global financial interconnectedness, and explain its role in transmitting instability; we investigate the political economy dynamics at the origin of regulatory asymmetries and government failures; and we discuss the limits of regulation.

Co-operative tensegrity-based formation control algorithm for a multi-aircraft system

This paper presents a tensegrity-based co-operative control algorithm for an aircraft formation. The 6 degrees-of-freedom model of the well-known Aerosonde unmanned aerial vehicle (UAV), is integrated with the model of the tensegrity structure and a decentralised control scheme is proposed. The strategy is shown to be scalable for 2n number of UAVs and is able to maintain a firm geometry whilst allowing flexible shape transformations. Simulation results demonstrate the effectiveness and stability of the proposed tensegrity-based formation control algorithm in 3D.

Dynamic adaptation of stability periods for service level agreements

A QoS adaptation to dynamically changing system conditions that takes into consideration the user’s constraints on the stability of service provisioning is presented. The goal is to allow the system to make QoS adaptation decisions in response to fluctuations in task traffic flow, under the control of the user. We pay special attention to the case where monitoring the stability period and resource load variation of Service Level Agreements for different types of services is used to dynamically adapt future stability periods, according to a feedback control scheme. System’s adaptation behaviour can be configured according to a desired confidence level on future resource usage. The viability of the proposed approach is validated by preliminary experiments.

An Extension of Estimation of Domain of Attraction for Fractional Order Linear System Subject to Saturation Control

This paper employs the Lyapunov direct method for the stability analysis of fractional order linear systems subject to input saturation. A new stability condition based on saturation function is adopted for estimating the domain of attraction via ellipsoid approach. To further improve this estimation, the auxiliary feedback is also supported by the concept of stability region. The advantages of the proposed method are twofold: (1) it is straightforward to handle the problem both in analysis and design because of using Lyapunov method, (2) the estimation leads to less conservative results. A numerical example illustrates the feasibility of the proposed method.

Therapeutics bioconjugates: evaluation of iminoboronates as payload delivery system for cancer

The advent of bioconjugation impacted deeply the world of sciences and technology. New biomolecules were found, biological processes were understood, and novel methodologies were formed due to the fast expansion of this area. The possibility of creating new effective therapies for diseases like cancer is one of big applications of this now big area of study. Off target toxicity was always the problem of potent small molecules with high activity towards specific tumour targets. However, chemotherapy is now selective due to powerful linkers that connect targeting molecules with affinity to interesting biological receptors and cytotoxic drugs. This linkers must have very specific properties, such as high stability in plasma, no toxicity, no interference with ligand affinity nor drug potency, and at the same time, be able to lyse once inside the target molecule to release the therapeutic warhead. Bipolar environments between tumour intracellular and extracellular medias are usually exploited by this linkers in order to complete this goal. The work done in this thesis explores a new model for that same task, specific cancer drug delivery. Iminoboronates were studied due to its remarkable selective stability towards a wide pH range and endogenous molecules. A fluorescence probe was design to validate this model by creating an Off/On system and determine the payload release location in situ. A process was optimized to synthetize the probe 8-(1-aminoethyl)-7-hydroxy-coumarin (1) through a reductive amination reaction in a microwave reactor with 61 % yield. A method to conjugate this probe to ABBA was also optimized, obtaining the iminoboronate in good yields in mild conditions. The iminoboronate model was studied regarding its stability in several simulated biological environments and each half-life time was determined, showing the conjugate is stable most of the cases except in tumour intracellular systems. The construction of folate-ABBA-coumarin bioconjugate have been made to complete this evaluation. The ability to be uptaken by a cancer cell through endocytosis process and the conjugation delivery of coumarin fluorescence payload are two features to hope for in this construct.

Importance of the HSP90 molecular chaperoning pathway for antibody diversification by determining AID stability

La protéine AID (déaminase induite par l’activation) joue un rôle central dans la réponse immunitaire adaptative. En désaminant des désoxycytidines en désoxyuridines au niveau des gènes immunoglobulines, elle initie l’hypermutation somatique (SHM), la conversion génique (iGC) et la commutation isotypique (CSR). Elle est essentielle à une réponse humorale efficace en contribuant à la maturation de l’affinité des anticorps et au changement de classe isotypique. Cependant, son activité mutagénique peut être oncogénique et causer une instabilité génomique propice au développement de cancers et de maladies autoimmunes. Il est donc critique de réguler AID, en particulier ses niveaux protéiques, pour générer une réponse immunitaire efficace tout en minimisant les risques de cancer et d’autoimmunité. Un élément de régulation est le fait qu’AID transite du cytoplasme vers le noyau mais reste majoritairement cytoplasmique à l’équilibre. AID est par ailleurs plus stable dans le cytoplasme que dans le noyau, ce qui contribue à réduire sa présence à proximité de l’ADN. Le but de cette thèse était d’identifier de nouveaux partenaires et déterminants d’AID régulant sa stabilité et ses fonctions biologiques. Dans un premier temps, nous avons identifié AID comme une nouvelle protéine cliente d’HSP90. Nous avons montré qu’HSP90 interagit avec AID dans le cytoplasme, ce qui empêche la poly-ubiquitination d’AID et sa dégradation par le protéasome. En conséquence, l’inhibition d’HSP90 résulte en une diminution significative des niveaux endogènes d’AID et corrèle avec une réduction proportionnelle de ses fonctions biologiques dans la diversification des anticorps mais aussi dans l’introduction de mutations aberrantes. Dans un second temps, nous avons montré que l’étape initiale dans la stabilisation d’AID par la voie de chaperonnage d’HSP90 dépend d’HSP40 et d’HSP70. En particulier, la protéine DnaJa1, qui fait partie de la famille des protéines HSP40s, limite la stabilisation d’AID dans le cytoplasme. La farnésylation de DnaJa1 est importante pour l’interaction entre DnaJa1 et AID et moduler les niveaux de DnaJa1 ou son état de farnésylation impacte à la fois les niveaux endogènes d’AID mais aussi la diversification des anticorps. Les souris DNAJA1-/- présentent une réponse immunitaire compromise en cas d’immunisation, qui est dûe à des niveaux réduits d’AID et un défaut de commutation de classe. Dans un troisième temps, nous avons montré que la protéine AID est intrinsèquement plus instable que sesprotéines paralogues APOBEC. Nous avons identifié l’acide aspartique en seconde position d’AID ainsi qu’un motif semblable au PEST comme des modulateurs de la stabilité d’AID. La modification de ces motifs augmente la stabilité d’AID et résulte en une diversification des anticorps plus efficace. En conclusion, l’instabilité intrinsèque d’AID est un élément de régulation de la diversification des anticorps. Cette instabilité est en partie compensée dans le cytoplasme par l’action protective de la voie de chaperonnage DnaJa1-HSP90. Par ailleurs, l’utilisation d’inhibiteurs d’HSP90 ou de farnésyltransférases pourrait être un outil intéressant pour la modulation indirecte des niveaux d’AID et le traitement de lymphomes/leucémies et de maladies auto-immunes causés par AID.

Targeted Public Distribution System in Food Grains:Extent of Utlization by the Tribal Population in Kerala

In India, Food Security meant supply of food grains and the medium was Public Distribution System. Public Distribution System (PDS) is a rationing mechanism that entitles households to specified quantities of selected commodities at subsidized prices. The Objectives of PDS are maintaining Price Stability, rationing during times of scarcity, welfare of the poor, and keeping a check on private trade. Kerala has registered remarkable improvement in poverty reduction in general over the years among all social sections, including scheduled caste and scheduled tribe population. As part of the structural adjustment intended to reduce public expenditure, PDS has been modified as Revamped PDS (RPDS) during 1992 and later on as Targeted PDS (TPDS) in 1997, intended to target households on the basis of income criterion, classifying people as Below Poverty Line (BPL) and Above Poverty Line (APL). TPDS provides 25Kg. of food gra.ins through the Fair Price Shops per month @ Rs.3/- per Kg. of rice/ wheat to the BPL category and @Rs.8.90 and Rs.6.7O for rice and wheat respectively to the APL category of people. Since TPDS is intended to target the poor people, the subsidy spent by the government for the scheme should be beneficial to the poor people and naturally they should utilize the benefits by purchasing the food grains allotted under the scheme. Several studies have shown that there is underutilization of the allotments under TPDS. Therefore, the extent of utilization of TPDS in food grains, how and why remains as a major hurdle, in improving the structure and system of PDS. Livelihood of the tribal population being under threat due to increasing degradation of the resources, the targeting system ought to be effective among the tribal population. Therefore, performance of the TPDS in food grains, in terms of the utilization by the tribal population in Kerala, impact thereof and the factors, if any, affecting proper utilization were considered as the research problem in this study. The study concentrated on the pattern of consumption of food grains by the tribal people, whether their hunger needs are met by distribution of food grains through the TPDS, extent to which TPDS in food grains reduce their share of expenditure on food in the total household expenditure, and the factors affecting the utilization of the TPDS in food grains by the tribal population. Going through the literature, it has been noted that only few studies concentrated on the utilization of TPDS in food grains among the tribal population in Kerala.The Research Design used in this study is descriptive in nature, but exploratory in some aspects. Idukki, Palakkad and Wayanad have more than 60% of the population of the tribals in the state. Within the three districts mentioned above, 14 villages with scheduled tribe concentration were selected for the study. 95 tribal colonies were selected from among the various tribal settlements. Collection of primary data was made from 1231 households with in the above tribal colonies. Analysis of data on the socio-economic factors of the tribal people, pattern of food consumption, extent of reduction in the share of expenditure on food among the household expenditure of the tribal people and the impact of TPDS on the tribal families etc. and testing of hypotheses to find out the relation/association of each of the six variables, using the data on BPL and APL categories of households separately have resulted in findings such as six percent of the tribal families do not have Ration Cards, average per capita consumption of food grains by the tribal people utilizing TPDS meets 62% of their minimum requirement, whereas the per capita consumption of food grains by the tribal people is higher than the national average per capita consumption, 63% deficiency in food grains may be felt by tribal people in general, if TPDS is withdrawn, and the deficit for BPL tribal people may be 82%, TPDS facilitates a reduction of 9.71% in the food expenditure among the total household expenditure of the tribal people in general, share of food to non-food among BPL category of tribals is 55:45 and 40:60 among the APL, Variables, viz. household income, number of members in the family and distance of FPS from tribal settlements etc. have influence on the quantity of rice being purchased by the tribal people from the Fair Price Shops, and there is influence of household income and distance of FPS from tribal settlements on the quantity of rice being purchased by the tribal people from the open market. Rationing with differential pricing on phased allotments, rectification of errors in targeting, anomalies in norms and procedures for classifying tribal people as BPL/APL, exclusive Income Generation for tribal population, paddy cultivation in the landholdings possessed by the tribal people, special drive for allotment of Ration Cards to the tribal people, especially those belonging to the BPL category, Mobile Fair Price Shops in tribal settlements, ensure quality of the food grains distributed through the TPDS, distribution of wheat flour in packed condition instead of wheat through the Fair Price Shops are recommended to address the shortcomings and weaknesses of the TPDS vis-avis the tribal population in Kerala.

An Alternative Approach To Computer System Security Monitoring And Enhancement Through System Call Sequence Analysis

Modern computer systems are plagued with stability and security problems: applications lose data, web servers are hacked, and systems crash under heavy load. Many of these problems or anomalies arise from rare program behavior caused by attacks or errors. A substantial percentage of the web-based attacks are due to buffer overflows. Many methods have been devised to detect and prevent anomalous situations that arise from buffer overflows. The current state-of-art of anomaly detection systems is relatively primitive and mainly depend on static code checking to take care of buffer overflow attacks. For protection, Stack Guards and I-leap Guards are also used in wide varieties.This dissertation proposes an anomaly detection system, based on frequencies of system calls in the system call trace. System call traces represented as frequency sequences are profiled using sequence sets. A sequence set is identified by the starting sequence and frequencies of specific system calls. The deviations of the current input sequence from the corresponding normal profile in the frequency pattern of system calls is computed and expressed as an anomaly score. A simple Bayesian model is used for an accurate detection.Experimental results are reported which show that frequency of system calls represented using sequence sets, captures the normal behavior of programs under normal conditions of usage. This captured behavior allows the system to detect anomalies with a low rate of false positives. Data are presented which show that Bayesian Network on frequency variations responds effectively to induced buffer overflows. It can also help administrators to detect deviations in program flow introduced due to errors.

Studies of stability of fluid flowa using variational methods

The study of stability problems is relevant to the study of structure of a physical system. It 1S particularly important when it is not possible to probe into its interior and obtain information on its structure by a direct method. The thesis states about stability theory that has become of dominant importance in the study of dynamical systems. and has many applications in basic fields like meteorology, oceanography, astrophysics and geophysics- to mention few of them. The definition of stability was found useful 1n many situations, but inadequate in many others so that a host of other important concepts have been introduced in past many years which are more or less related to the first definition and to the common sense meaning of stability. In recent years the theoretical developments in the studies of instabilities and turbulence have been as profound as the developments in experimental methods. The study here Points to a new direction for stability studies based on Lagrangian formulation instead of the Hamiltonian formulation used by other authors.

Assessment of Convective Activity Using Stability Indices as Inferred from Radiosonde and MODIS Data

The combined use of both radiosonde data and three-dimensional satellite derived data over ocean and land is useful for a better understanding of atmospheric thermodynamics. Here, an attempt is made to study the ther-modynamic structure of convective atmosphere during pre-monsoon season over southwest peninsular India utilizing satellite derived data and radiosonde data. The stability indices were computed for the selected stations over southwest peninsular India viz: Thiruvananthapuram and Cochin, using the radiosonde data for five pre- monsoon seasons. The stability indices studied for the region are Showalter Index (SI), K Index (KI), Lifted In-dex (LI), Total Totals Index (TTI), Humidity Index (HI), Deep Convective Index (DCI) and thermodynamic pa-rameters such as Convective Available Potential Energy (CAPE) and Convective Inhibition Energy (CINE). The traditional Showalter Index has been modified to incorporate the thermodynamics over tropical region. MODIS data over South Peninsular India is also used for the study. When there is a convective system over south penin-sular India, the value of LI over the region is less than −4. On the other hand, the region where LI is more than 2 is comparatively stable without any convection. Similarly, when KI values are in the range 35 to 40, there is a possibility for convection. The threshold value for TTI is found to be between 50 and 55. Further, we found that prior to convection, dry bulb temperature at 1000, 850, 700 and 500 hPa is minimum and the dew point tem-perature is a maximum, which leads to increase in relative humidity. The total column water vapor is maximum in the convective region and minimum in the stable region. The threshold values for the different stability indices are found to be agreeing with that reported in literature.

Nitrification in a packed bed bioreactor integrated into amarine recirculating maturation system under different substrate concentrations and flow rates

BACKGROUND: A packed bed bioreactor (PBBR) activated with an indigenous nitrifying bacterial consortia was developed and commercialized for rapid establishment of nitrification in brackish water and marine hatchery systems in the tropics. The present study evaluated nitrification in PBBR integrated into a Penaeus monodon recirculating maturation system under different substrate concentrations and flow rates. RESULTS:Instantnitrificationwasobservedafter integration ofPBBRinto thematuration system.TANandNO2-Nconcentrations were always maintained below0.5 mg L−1 during operation. The TANandNO2-N removalwas significant (P < 0.001) in all the six reactor compartments of the PBBR having the substrates at initial concentrations of 2, 5 and 10 mg L−1. The average volumetric TAN removal rates increased with flow rates from 43.51 (250 L h−1) to 130.44 (2500 L h−1) gTAN m−3 day−1 (P < 0.05). FISH analysis of the biofilms after 70 days of operation gave positive results with probes NSO 190 ((β ammonia oxidizers), NsV 443 (Nitrosospira spp.) NEU (halophilic Nitrosomonas), Ntspa 712 (Phylum Nitrospira) indicating stability of the consortia. CONCLUSION: The PBBR integrated into the P. monodon maturation system exhibited significant nitrification upon operation for 70 days as well as at different substrate concentrations and flow rates. This system can easily be integrated into marine and brackish water aquaculture systems, to establish instantaneous nitrification

Sequential interactions of Silver-silica nanocomposite (Ag-SiO2NC) with cell wall, metabolism and genetic stability of Psedomonas aeruginosa, a multiple antibiotic resistant bacterium

The study was carried out to understand the effect of silver-silica nanocomposite (Ag-SiO2NC) on the cell wall integrity, metabolism and genetic stability of Pseudomonas aeruginosa, a multiple drugresistant bacterium. Bacterial sensitivity towards antibiotics and Ag-SiO2NC was studied using standard disc diffusion and death rate assay, respectively. The effect of Ag-SiO2NC on cell wall integrity was monitored using SDS assay and fatty acid profile analysis while the effect on metabolism and genetic stability was assayed microscopically, using CTC viability staining and comet assay, respectively. P. aeruginosa was found to be resistant to β-lactamase, glycopeptidase, sulfonamide, quinolones, nitrofurantoin and macrolides classes of antibiotics. Complete mortality of the bacterium was achieved with 80 μgml-1 concentration of Ag-SiO2NC. The cell wall integrity reduced with increasing time and reached a plateau of 70 % in 110 min. Changes were also noticed in the proportion of fatty acids after the treatment. Inside the cytoplasm, a complete inhibition of electron transport system was achieved with 100 μgml-1 Ag-SiO2NC, followed by DNA breakage. The study thus demonstrates that Ag-SiO2NC invades the cytoplasm of the multiple drug-resistant P. aeruginosa by impinging upon the cell wall integrity and kills the cells by interfering with electron transport chain and the genetic stability

FEM based Virtual Prototyping and Design of Third Harmonic Excitation System for Low Voltage Brushless Alternators

Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.