Mineralogy of selected geological deposits from the United Kingdom and the Republic of Ireland as possible capping materials for low-level radioactive waste disposal facilities

Solid low-level radioactive waste (LLW) is currently being disposed at a number of facilities in the United Kingdom (UK). The safety of these facilities relies to some extent on the use of engineered barriers, such as a cap, to isolate the waste and protect the environment. Generally, the material used as the barrier layer within such a cap should be of low permeability and it should retain this property over long timescales (beyond a few decades normally required for facilities containing non-radioactive wastes). The objective of this research is to determine the mineralogy of selected geological deposits from the UK and Ireland as part of a larger project to examine their suitability as a capping material, particularly on LLW sites. Mineral transformations, as a result of future climate change, may impact on the long-term performance of the cap and even the disposal facility. X-ray diffraction (XRD) was carried-out on the sand, silt and clay fractions of the London Clay, Belfast Upper Boulder Clay, Irish Glacial Till, Belfast Sleech, and Ampthill Clay geological deposits. Minerals were present that could pose both positive and negative effects on the long-term performance of the cap. Smectite, which has a high shrink swell potential, may produce cracks in London Clay, Belfast Upper Boulder Clay and Ampthill Clay capping material during dry, hotter periods as a possible consequence of future climate change; thus, resulting in higher permeability. Ampthill Clay and Belfast Sleech had elevated amounts of organic matter (OM) at 5.93% and 5.88%, respectively, which may also contribute to cracking. Over time, this OM may decompose and result in increased permeability. Gypsum (CaSO4) in the silt and sand fractions of Ampthill Clay may reduce the impact of erosion during wetter periods if it is incorporated into the upper portion of the cap. There are potential negative effects from the acidity created by the weathering of pyrite (FeS2) present in the silt and sand fractions of Belfast Sleech and Ampthill Clay that could impede the growth of grasses used to stabilize the surface of the capping material if this material is used as part of the vegetative soil layer. Additionally, acidic waters generated from pyrite weathering could negatively impact the lower lying capping layers and the disposal facility in general. However, the calcium carbonate (CaCO3) present in the silt and sand fractions of these deposits, and dolomite (CaMg(CO3)2) in Belfast Sleech, may counter act the acidity.

The effect of osteogenic growth factors on bone growth into a ceramic filled defect around an implant

Currently available synthetic bone substitutes perform poorly compared to autograft. It is hoped that by adding osteogenic growth factors to the materials, new bone formation could be increased and the clinical outcome improved. In this study, IGF-1, bFGF and TGFbeta1, alone and in combination, were absorbed onto a carrier of P-tricalcium phosphate (PTCP) and implanted into a defect around a hydroxyapatite-coated, stainless steel implant in the proximal tibia of rat in a model of revision arthroplasty. Animals were sacrificed at 6 and 26 weeks for routine histology and histomorphometry and mechanical push out tests. The results show that only bFGF had a significant effect on ceramic resorption. The groups that received bFGF and bFGF in combination with TGFbeta1 had smaller and fewer betaTCP particles remaining in the defect at 6 and 26 weeks. No growth factor combination significantly enhanced new bone formation or the mechanical strength of the implant. These results indicate that, of the growth factors tested, only bFGF had any beneficial effect on the host response to the implant, perhaps by delaying osteoblast differentiation and thereby prolonging osteoclast access to the ceramic. (C) 2004 Orthopaedic Research Society. Published by Elsevier Ltd. All rights reserved.

Nonlinear propagation of electromagnetic waves in negative-refraction-index composite materials

We investigate the nonlinear propagation of electromagnetic waves in left-handed materials. For this purpose, we consider a set of coupled nonlinear Schrodinger (CNLS) equations, which govern the dynamics of coupled electric and magnetic field envelopes. The CNLS equations are used to obtain a nonlinear dispersion, which depicts the modulational stability profile of the coupled plane-wave solutions in left-handed materials. An exact (in)stability criterion for modulational interactions is derived, and analytical expressions for the instability growth rate are obtained.

Force-induced activation of covalent bonds in mechanoresponsive polymeric materials

Mechanochemical transduction enables an extraordinary range of physiological processes such as the sense of touch, hearing, balance, muscle contraction, and the growth and remodelling of tissue and
bone1–6. Although biology is replete with materials systems that actively and functionally respond to mechanical stimuli, the default mechanochemical reaction of bulk polymers to large external stress is the unselective scission of covalent bonds, resulting in damage or failure7. An alternative to this degradation process is the rational molecular design of synthetic materials such that mechanical stress
favourably altersmaterial properties. A few mechanosensitive polymers with this property have been developed8–14; but their active response is mediated through non-covalent processes, which may
limit the extent to which properties can be modified and the longterm stability in structural materials. Previously, we have shown with dissolved polymer strands incorporating mechanically sensitive chemical groups—so-called mechanophores—that the directional nature of mechanical forces can selectively break and re-form covalent bonds15,16. We now demonstrate that such forceinduced covalent-bond activation can also be realized with mechanophore-linked elastomeric and glassy polymers, by using a mechanophore that changes colour as it undergoes a reversible electrocyclic ring-opening reaction under tensile stress and thus allows us to directly and locally visualize the mechanochemical reaction. We find that pronounced changes in colour and fluorescence emerge with the accumulation of plastic deformation, indicating that in these polymeric materials the transduction of mechanical force into the ring-opening reaction is an activated process. We anticipate that force activation of covalent bonds can serve as a general strategy for the development of new mechanophore building blocks that impart polymeric materials with desirable functionalities ranging from damage sensing to fully regenerative self-healing.

Single crystal CVD diamond growth strategy by the use of a 3D geometrical model: Growth on (113) oriented substrates

The quality of single crystal diamond obtained by microwave CVD processes has been drastically improved in the last 5 years thanks to surface pretreatment of the substrates [A. Tallaire, J. Achard, F. Silva, R.S. Sussmann, A. Gicquel, E. Rzepka, Physica Status Solidi (A) 201, 2419-2424 (2004); G. Bogdan, M. Nesladek, J. D'Haen, J. Maes, V.V. Moshchalkov, K. Haenen, M. D'Olieslaeger, Physica Status Solidi (A) 202, 2066-2072 (2005); M. Yamamoto, T. Teraji, T. Ito, Journal of Crystal Growth 285, 130-136 (2005)]. Additionally, recent results have unambiguously shown the occurrence of (110) faces on crystal edges and (113) faces on crystal corners [F. Silva, J. Achard, X. Bonnin, A. Michau, A. Tallaire, O. Brinza, A. Gicquel, Physica Status Solidi (A) 203, 3049-3055 (2006)]. We have developed a 3D geometrical growth model to account for the final crystal morphology. The basic parameters of this growth model are the relative displacement speeds of (111), (110) and (113) faces normalized to that of the (100) faces, respectively alpha, beta, and gamma. This model predicts both the final equilibrium shape of the crystal (i.e. after infinite growth time) and the crystal morphology as a function of alpha, beta, gamma, and deposition time.

An optimized operating point, deduced from the model, has been validated experimentally by measuring the growth rate in (100), (111), (110), and (113) orientations. Furthermore, the evolution of alpha, beta, gamma as a function of methane concentration in the gas discharge has been established. From these results, crystal growth strategies can be proposed in order, for example, to enlarge the deposition area. In particular, we will show, using the growth model, that the only possibility to significantly increase the deposition area is, for our growth conditions, to use a (113) oriented substrate. A comparison between the grown crystal and the model results will be discussed and characterizations of the grown film (Photoluminescence spectroscopy, EPR, SEM) will be presented. (C) 2008 Elsevier B.V. All rights reserved.

Thermo-Mechanical Properties of Poly ε-Caprolactone/Poly L-Lactic Acid Blends: Addition of Nalidixic Acid and Polyethylene Glycol Additives Journal of the Mechanical Behavior of Biomedical Materials

The search for ideal biomaterials is still on-going for tissue regeneration. In this study, blends of Poly ε-caprolactone (PCL) with Poly l-lactic acid (PLLA), Nalidixic Acid (NA) and Polyethylene glycol (PEG) were prepared. Mechanical and thermal properties of the blends were investigated by tensile and flexural analysis, DSC, TGA, WXRD, MFI, BET, SEM and hot stage optical microscopy. Results showed that the loading of PLLA caused a significant decrease in tensile strength and almost total eradication of the elongation at break of PCL matrix, especially after PEG and NA addition. Increased stiffness was also noted with additional NA, PEG and PLLA, resulting in an increase in the flexural modulus of the blends.
Isothermal degradation indicated that bulk PCL, PLLA and the blends were thermally stable at 200°C for the duration of 2h making extrusion of the blends at this temperature viable. Morphological study showed that increasing the PLLA content and addition of the very low viscosity PEG and powder NA decreased the Melt Flow Indexer and increased the viscosity.
At the higher temperature the PLLA begins to soften and eventually melts allowing for increased flow and, coupling this with, the natural increase in MFI caused by temperature is enhanced further. The PEG and NA addition increased dramatically the pore volume which is important for cell growth and flow transport of nutrients and metabolic waste.

Epitaxial growth of non-c-oriented ferroelectric SrBi2Ta2O9 thin films on Si(100) substrates

Epitaxial SrBi2Ta2O9 (SBT) thin films with well-defined (116) orientation have been grown by pulsed laser deposition on Si(100) substrates covered with an yttria-stabilized ZrO2 (YSZ) buffer layer and an epitaxial layer of electrically conductive SrRuO3. Studies on the in-plane crystallographic relations between SrRuO3 and YSZ revealed a rectangle-on-cube epitaxy with respect to the substrate. X-ray diffraction pole figure measurements revealed well defined orientation relations, viz. SBT(116)\\ SrRuO3(110)\\ YSZ(100)\\ Si(100), SBT[110]\\ SrRuO3[001], and SrRuO3[111]\\ YSZ[110]\\ Si[110].

Initial growth stages of epitaxial BaTiO3 films on vicinal SrTiO3 : Nb (001) substrates

The growth mechanism of epitaxial BaTiO3 films on vicinal Nb-doped SrTiO3 (srTiO(3):Nb) (001) substrate surfaces was studied in terms of surface morphology, crystalline orientation, microstructure, and film/substrate interface. Well-oriented BaTiO3 thin films were grown on SrTiO3 substrates with well-defined terraces by pulsed laser deposition. The regularly terraced TiO2-terminated surfaces of vicinal SrTiO3:Nb (001) substrates were prepared by a definite chemical and thermal treatment. Under our conditions, BaTiO3 seems to grow with a layer-then-island (Stranski-Krastanov) growth mechanism. In order to investigate the orientation and crystallinity of the BaTiO3 films, x-ray diffraction and high-resolution transmission election microscopy were performed. Ferroelectricity of the BaTiO3 films was proved by electrical measurements performed on Pt/BaTiO3/SrTiO3:Nb heterostructures.

An Investigation into the Role of Polymeric Carriers on Crystal Growth within Amorphous Solid Dispersion Systems

Using phase diagrams derived from Flory–Huggins theory, we defined the thermodynamic state of amorphous felodipine within three different polymeric carriers. Variation in the solubility and miscibility of felodipine within different polymeric materials (using F–H theory) has been identified and used to select the most suitable polymeric carriers for the production of amorphous drug–polymer solid dispersions. With this information, amorphous felodipine solid dispersions were manufactured using three different polymeric materials (HPMCAS-HF, Soluplus, and PVPK15) at predefined drug loadings, and the crystal growth rates of felodipine from these solid dispersions were investigated. Crystallization of amorphous felodipine was studied using Raman spectral imaging and polarized light microscopy. Using this data, we examined the correlation among several characteristics of solid dispersions to the crystal growth rate of felodipine. An exponential relationship was found to exist between drug loading and crystal growth rate. Moreover, crystal growth within all selected amorphous drug–polymer solid dispersion systems were viscosity dependent (η–ξ). The exponent, ξ, was estimated to be 1.36 at a temperature of 80 °C. Values of ξ exceeding 1 may indicate strong viscosity dependent crystal growth in the amorphous drug–polymer solid dispersion systems. We argue that the elevated exponent value (ξ > 1) is a result of drug–polymer mixing which leads to a less fragile amorphous drug–polymer solid dispersion system. All systems investigated displayed an upper critical solution temperature, and the solid–liquid boundary was always higher than the spinodal decomposition curve. Furthermore, for PVP–FD amorphous dispersions at drug loadings exceeding 0.6 volume ratio, the mechanism of phase separation within the metastable zone was found to be driven by nucleation and growth rather than liquid–liquid separation.

Chalcogenide thin films for solar cells: growth and properties

Thin film solar cells have in recent years gained market quota against traditional silicon photovoltaic panels. These developments were in a large part due to CdTe solar panels on whose development started earlier than their competitors. Panels based on Cu(In,Ga)Se2 (CIGS), despite being more efficient in a laboratory and industrial scale than the CdTe ones, still need a growth technology cheaper and easier to apply in industry. Although usually presented as a good candidate to make cheap panels, CIGS uses rare and expensive materials as In and Ga. The price evolution of these materials might jeopardize CIGS future. This thesis presents three different studies. The first is the study of different processes for the incorporation of Ga in a hybrid CIGS growth system. This system is based on sputtering and thermal evaporation. This technology is, in principle, easier to be applied in the industry and solar cells with efficiencies around to 7% were fully made in Aveiro. In the second part of this thesis, a new material to replace CIGS in thin film solar cells is studied. The growth conditions and fundamental properties of Cu2ZnSnSe4 (CZTSe) were studied in depth. Suitable conditions of temperature and pressure for the growth of this material are reported. Its band gap energy was estimated at 1.05 eV and the Raman scattering peaks were identified. Solar cells made with this material showed efficiencies lower than 0.1%. Finally, preliminary work regarding the incorporation of selenium in Cu2ZnSnS4 (CZTS) thin films was carried out. The structural and morphological properties of thin films of Cu2ZnSn(S,Se)4 have been studied and the results show that the incorporation of selenium is higher in films with precursors rather with already formed Cu2SnS3 or Cu2ZnSnS4 thin films. A solar cell with 0.9 % of efficiency was prepared.

Novel furan polymer materials based on the reversible Diels-Alder reaction

A futura e inevitável escassez dos recursos fósseis, juntamente com o aumento imprevisível dos seus preços, levou, nas últimas décadas, a um aumento impressionante de iniciativas dedicadas não só à procura de fontes alternativas de fornecedores de energia, mas também de produtos químicos e polímeros a partir de fontes renováveis, em particular da biomassa vegetal. Entre estes, os polímeros derivados de monómeros furânicos constituem uma classe única de materiais cujas estruturas podem, em princípio, simular virtualmente os seus homólogos actualmente derivados de recursos fósseis. O anel furânico é uma estrutura heterocíclica com um carácter diénico pronunciado, o que torna-o um dieno particularmente apropriado para a reacção de Diels-Alder (DA) com dienófilos como a maleimida. Um dos aspectos mais relevantes da reacção de DA é a sua reversibilidade em função da temperatura, a qual permite que os aductos sejam facilmente revertidos nos seus precursores por aumento da temperatura (reacção de retro-DA). No caso específico da combinação furano-maleimida, a formação do aducto predomina até cerca de 60ºC, enquanto a reacção inversa é dominante acima de 100ºC. A combinação desta característica da reacção de DA com a química de compostos furânicos pode abrir um novo caminho para a preparação de materiais macromoleculares funcionais com base em fontes renováveis e com aplicações promissoras como auto-reparação e reciclabilidade. O principal objectivo desta Tese, é a síntese e caracterização de novos materiais poliméricos termo-reversíveis, aplicando a reacção de DA a monómeros complementares com estruturas dos tipos furânico (o dieno, designado por A) e de maleimida (o dienófilo, designado por B). A primeira etapa neste trabalho envolveu a síntese, purificação e caracterização de novos monómeros furânicos e de maleimida do tipo AA, A3, BB, B3, AB, AB2, cada um com diferentes grupos separadores das funções reactivas. Posteriormente, estes monómeros foram polimerizados e despolimerizados por ciclos de DA/retro-DA utilizando diferentes combinações. A formação e dissociação de todos os aductos de DA foram seguidas por ambas espectroscopias de UV e RMN de 1H. O primeiro sistema de DA estudado foi uma combinação modelo entre reagentes mono-funcionais (-A+-B), nomeadamente o acetato furfurílico (FA) e a N-metilmaleimida (MM), ambos comercialmente disponíveis. O objectivo desta abordagem foi estudar a cinética e o equilíbrio da formação/dissociação dos aductos de DA e obter indicações sobre as condições mais adequadas a serem usadas na preparação dos correspondentes novos materiais macromoleculares. Além disso, pretendia-se verificar a presença ou ausência de reacções secundárias que poderiam intervir em ambas as vias directa e inversa das reacções, mesmo após vários ciclos. A espectroscopia de UV forneceu informação quantitativa sobre a cinética de formação do aducto através da diminuição progressiva da absorvência máxima a 293 nm correspondente ao grupo maleimida, a diferentes temperaturas (35, 50, 65 ºC) Reciprocamente, a correspondente reacção de retro-DA foi seguida a 90 ºC através do aumento do mesmo pico. A reversibilidade destes sistemas foi verificada com sucesso após uma sequência de ciclos de DA/retro-DA. Adicionalmente, verificou-se que os espectros originaram um ponto isosbéstico, provando que estes sistemas não envolvem quaisquer reacções secundárias. Uma vez que foi usado um excesso de FA, as reacções de DA modelo apresentaram um comportamento cinético de pseudo-primeira ordem, com a constante de velocidade k mais alta (2.1x10-5 dm3mol-1s-1) para T=65 ºC. A correspondente energia de activação foi de 39.0 kJ.mol-1. A reacção de retro-DA seguiu um comportamento de primeira ordem, com constante de velocidade de 1.6x10-6 s-1. A evolução deste sistema por RMN de 1H a 65ºC deu-nos informações mais detalhadas sobre a sua evolução estrutural, ou seja, à medida que a intensidade dos picos atribuídos à formação do aducto aumentaram progressivamente ao longo do tempo, os pertencentes aos reagentes iniciais diminuiram proporcionalmente. O “rendimento final”, calculado após 20 dias à temperatura ambiente, foi de aproximadamente 70%. A reacção de retro-DA foi depois seguida a 90ºC, observando-se tal como na espectroscopia de UV, o deslocamento da reacção no sentido da regeneração dos reagentes de partida. A viabilidade de múltiplos ciclos de DA/retro-DA estabelecidos pela espectroscopia de UV foi igualmente confirmada por RMN de 1H. O passo seguinte envolveu o estudo de um sistema de policondensação linear baseado no crescimento gradual por reacção de DA entre um monómero bisfurânico A-A e um do tipo bismaleimida B-B, seguindo a mesma abordagem que no sistema modelo. O poliaducto linear foi obtido a partir de soluções equimolares dos monómeros, por reacção de DA a 65ºC. O progresso desta polimerização foi seguido por espectroscopia de UV e RMN de 1H e, mais qualitativamente, pelo aumento da viscosidade do meio. A reacção seguiu um comportamento de segunda ordem, com uma constante de velocidade de 9.4x10-6 dm3mol-1s-1, e observou-se novamente um ponto isosbéstico nos dados de UV. Os espectros de RMN apresentaram o padrão esperado, nomeadamente o aumento progressivo dos sinais associados ao aducto e a correspondente diminuição dos grupos furano e maleimida livres. A despolimerização do poliaducto através da reacção de retro-DA foi seguida a 110ºC usando as mesmas técnicas. Os dados de UV mostraram o retorno progressivo da absorção dos grupos de maleimida, seguindo um comportamento cinético de primeira ordem, com constante de velocidade de 2.5x10-6 s-1, até à completa regeneração de ambos os monómeros. Os espectros de RMN providenciaram mais uma vez informação estrutural sobre o progresso da despolimerização, a qual foi acompanhada por uma diminuição progressiva da viscosidade. Adicionalmente, para seguir a retro- DA, adicionou-se um excesso de composto furânico monofuncional, nomeadamente o 2,5-dimetilfurano (DMFu), ao sistema de modo a bloquear as funções maleimida complementares, evitando assim a repolimerização após arrefecimento. Os productos isolados foram então o monómero bisfurânico AA, DMFu que não reagiu e o bisaducto não-polimerizável de BB com DMFu. Este resultado indicou claramente que o polímero foi de facto revertido nos seus monómeros durante a reacção de retro-DA. O terceiro sistema estudado foi outra polimerização linear, seguindo as mesmas condições experimentais que os anteriores, mas com uma estratégia diferente de modo a contornar o problema clássico de assegurar a estequiometria exacta dos monómeros. As estruturas dos monómeros utilizados incorporam ambos os grupos reactivos, i.e, moléculas do tipo A-B. A polimerização prematura destes monómeros intrinsecamente reactivos foi evitada com a protecção do grupo maleimida na forma de um aducto de DA com furano, até a incorporação do substituinte furânico na outra extremidade. Portanto, a policondensação destes monómeros foi iniciada após a desprotecção in situ deste composto mediante aquecimento, seguido de arrefecimento até à temperatura adequada para polimerizar. Os resultados obtidos por UV e RMN sugerem que de facto o uso de monómeros do tipo A-B oferece um melhor sistema linear. Em seguida, foram estudados sistemas de policondensação não-linear por reacção de DA, entre monómeros (um ou ambos) com funcionalidade superior a dois, nomeadamente sistemas do tipo A3+B-B ou A-A+B3, seguindo mais uma vez as mesmas condições experimentais. Uma vez que utilizam monómeros complementares contendo, em média, mais de duas funcionalidades, estes sistemas conduzem a materiais reticulados. Nestes estudos, foram usadas três razões molares de [maleimida]/[furano], nomeadamente 1.0, 0.75 e 0.5, de modo a estudar ambas as situações de não-gelificação e reticulação. Ambos sistemas apresentaram um comportamento regular e boa reciclabilidade quer para gerar situações que possam conduzir à formação de redes a diferentes graus de conversão, ou que possam parar antes da sua obtenção, conforme previsto pela equação de Flory-Stockmayer. Como esperado, a utilização de grupos complementares em quantidades estequiométricas produziu o espessamento mais rápido e a reticulação quase completa; à medida que a quantidade relativa de monómero trifuncional decresceu, as reacções pararam antes da reticulação, ou seja, originaram meios altamente viscosos contendo polímeros solúveis altamente ramificados. As reacções de retro-DA a 110 ºC conduziram à gradual dissolução das partículas de gel (quando presentes), tendo sido comprovado pelos espectros de UV e de RMN de 1H, evidenciado a regeneração dos monómeros. Tal como no sistema do tipo A-A+B-B, a reacção de retro-DA foi seguida adicionando um excesso de DMFu ao sistema reaccional. Como esperado, os produtos finais foram os monómeros furânicos, o DMFu em excesso e o trisaducto ou o bisaducto maleimida-DMFu, o que confirma a eficiência da despolimerização com regeneração dos monómeros iniciais. O último sistema de policondensação por reacção de DA envolveu um monómero assimetricamente substituído do tipo AB2, capaz de originar estruturas macromoleculares hiper-ramificadas que não reticulam. Este estudo preliminar deste sistema foi seguido nas mesmas condições experimentais que os anteriores, apresentando um comportamento com as características esperadas.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).