Iluminação de exteriores utilizando tecnologia LED: estudo de caso

This Graduate Work aims to exhibit the analyze of the applicability of LED technology in a real outdoor lighting situation, and this project’s illumination solution is compared with the initial proposal, the sodium vapor lamps. What is studied is an outdoor area, like the roads and parking lots of a plant. A light planning software is used for this comparison, and the results are displayed instantly, allowing rapid analysis of the project through a simulation. The medium illuminance is the same in both solutions for this case study and minimum rates set as standard were observed then the analysis are appropriate in this project. Various aspects are considered in order to obtain a comprehensive analysis of this project, such as economic, environmental and quality of lighting. LED technology in outdoor lighting is presented in its infancy, but promising. Solid state lamps show great advantages when compared with other technologies, such as discharge lamps, however there are some disadvantages tied to new products that are expected to be overcome with technological development and increased production

Plano de iluminação externa da UNESP Campus Itapeva com base em LED e energia solar

This work presents the development of the External Lighting Plan UNESP in the Itapeva Campus based LED and Solar Energy. Firstly it was made a collection of data from measurements of the local transit through the Google Earth 6 software and divide the local in sectors, and then perform an analysis of characteristics and age of the site. With these data it was possible to determine the average luminance the place, in30 lux. After these procedures was possible to determine the type of sets that would perform the role of bridge lighting the kit chosen was the 20/20 Sun LED manufacturer, since it contains the luminaire with the solar panel to the pole. Therefore we determined the number of poles for each sector, whichwas72in total and. After the determination of the location of each point lighting

Análise da influência da iluminação de rodovias federais com a redução do número de acidentes

The increasing rate of traffic accidents, followed by the high rate of mortality due to these occurrences, favored to the classification of traffic accidents as a public health problem in Brazil. These accidents consume a significant portion of Gross Domestic Product (GDP), especially related to the victims. Considering this scenery with many tragedies and resources being spent only in the end, this paper seeks to examine the influence of federal highways lighting by reducing the number of accidents. Federal Highways sections that received lighting were taken up for study, therefore a survey of statistical data has been raised considering the accidents before and after the route had been illuminated. Taking advantage of the results obtained, an economic analysis has been made considering the amounts consumed by traffic accidents versus the values required for the installation of lighting on highways

Estudo sobre iluminação e banco de capacitores de uma típica indústria metalúrgica

The use of electricity for obtaining light has been quite an issue currently discussed, either through new technologies that are emerging, the quest for greater efficiency, reduced waste and rational use. This work comprises a lighting design applied to a metallurgical based Brazilian Standard 5413 which mentions levels of luminance for interior and, in the case of this work, for a sandblasting booth. Ways to improve the workplace and luminosity presented before the project and also after its implementation are discussed. Technologies are chosen guided by technical calculations according to the illuminance values they want to reach for the environment studied. All pertinent design features are critically analyzed and discussed, and at the end proposals are presented, relating to each other in a comparative framework, so the best solution is applied in a practical way in the enclosure. Results are also presented concerning the maintenance of a bank of capacitors to correct the power factor for the metals studied company

Desenvolvimento de um conversor estático PWM para o acionamento de LED’S para iluminação publica

This work deals with the development of a switched-mode power supply circuit based on a Buck topology converter with a Boost Rectifier One-Cycle Control with Power Factor Correction developing, thus, a source of direct current for a module of 50 power LEDs that will be used in a lamp for public street lightning. It is presented, at first, some aspects about the most common technologies used in lamps of public street lightning in Brazil and a comparison with the White LED high power, which is the one that presents itself as the most promising among the existing market. Then it is presented the detailed development of the static converter switched PWM, consisting of a Boost rectifier with power factor correction and methodology of control One-Cycle Control associated with a Buck converter controlled by a PI method that operates as a direct current source . At the end of the simulation results of the circuit through the PSIM software are presented to verify the design behavior

Ergonomia de tablets em uso ocupacional: atividade visual e biomecânica postural sob a influência de ofuscamentos reflexivos causados pela iluminação

Pós-graduação em Design - FAAC

Reconhecimento de faces sob diferentes condições de iluminação utilizando PCA e a transformada census

Os seres humanos identificam naturalmente outros seres humanos utilizando suas características físicas, fisiológicas ou comportamentais. Dentre essas características, destacam-se os traços faciais. O avanço tecnológico na área de Biometria tem promovido o desenvolvimento de inúmeras técnicas para o reconhecimento automático de faces por meio de computadores, entretanto, existem ainda vários fatores que dificultam esta aplicação, como por exemplo, a variação das condições de iluminação. O objetivo deste artigo é analisar os efeitos da aplicação de um filtro de processamento de imagens, denominado Transformada Census, em uma base de dados com imagens da face em diferentes condições de iluminação. Assim, experimentos foram realizados utilizando a técnica PCA com imagens da base de dados AR antes e depois da aplicação da Transformada Census. Os resultados desses experimentos mostraram que a aplicação da Transformada Census melhorou o resultado do reconhecimento das faces, reduzindo a taxa de erro.

Inclusão digital no ensino de iluminação natural

The teaching/learning activities of the daylighting built environment require from the Architecture and Urbanism undergraduate student the ability to abstract the effects of daylight distributed in three-dimensional space that is being designed. Several tools and techniques can be used to facilitate the understanding of the involved phenomena, among which the computational simulation. This paper reports the digital inclusion of the daylighting teaching in the Architecture and Urbanism undergraduate course at the School of Architecture, Arts and Social Communication of Bauru (FAAC) of UNESP – Sao Paulo State University, that began in 2010. The inclusion process involved free software use, specifically the programs DIALux and SketchUp+Radiance, both with graphical output for the illuminated scenes visualization and for result analysis. The graphic model is converted from SketchUp to Radiance by a plugin and a user-friendly interface for Windows was developed to simulate the lighting. The process of digital inclusion is consolidated, with wide acceptance by students, for which computational simulation facilitates understanding of relation between daylight and built environment and helps the design process of elements for daylighting control.

Impacto da redução do nível de tensão na iluminação residencial em uma rede inteligente

In this paper, we will present an overview of the smart grid defining the three main systems that compose it: smart infrastructure system, smart management system and smart protection system. We will conceptualize a functionality of smart management system, the conservative voltage reduction, citing its benefits and its history of application. And, finally, we'll cover a test in which we reduce the nominal voltages on incandescent bulbs, CFL and LED, in the context of residential lighting, and on LED and HPS, in the context of public lighting. The test aims to check whether the voltage reduction adversely affects sources of lighting by measuring the temperature manually with a thermal imaging camera FLIR and illuminance with a LUX meter. The set of power factor, total harmonic distortion, and input power values will be collected automatically through the power quality Analyzer Fluke 345 with a probe Fluke Hall Effect Current. For residential lighting, it was found that both CFL and LED had good performance with the smallest variations in illuminance. Between both, the LED source had the lowest harmonics and the lowest power consumption, on the other hand incandescent bulbs had a bad performance as expected. Public light sources also had a good performance and obtained power factors within the standards, as opposed to the CFL and LED residential sources. The data collected clearly shows the feasibility for nominal voltage reductions. Even with small reductions, there are possibilities of savings which can be passed on to the utilities and consumers

Sistema autônomo de iluminação utilizando energia solar

This work presents a self-sustainable lighting system using ultracapacitor as a storage device, replacing the conventional battery, using solar energy as the only energy supplier. A detailed study of solar panels, switched mode converters and ultracapacitors was made, in order to design a circuit capable of capturing solar energy and transfer it efficiently to a bank of ultracapacitors. Later, at nighttime, this energy is used for lighting in LED luminaires which have high luminous efficiency and high reliability index. This work presents the design of the solar panel, ultracapacitors bank, the development of the voltage converter circuit and charger working at the maximum power point of the solar panel. All subsystems were simulated and it was shown that the use of ultracapacitors is feasible to feed a LED lamp with enough brightness for a person to walk at night, for two night shifts, using a capacitive bank with twenty-four ultracapacitors. Replacing the battery by an ultracapacitor allows a faster recharge, with low maintenance costs, since ultracapacitors have a lifetime bigger than batteries; beyond reducing the environmental impact, as they don't use potentially toxic chemical compounds

Impacto da redução do nível de tensão na iluminação residencial em uma rede inteligente

In this paper, we will present an overview of the smart grid defining the three main systems that compose it: smart infrastructure system, smart management system and smart protection system. We will conceptualize a functionality of smart management system, the conservative voltage reduction, citing its benefits and its history of application. And, finally, we'll cover a test in which we reduce the nominal voltages on incandescent bulbs, CFL and LED, in the context of residential lighting, and on LED and HPS, in the context of public lighting. The test aims to check whether the voltage reduction adversely affects sources of lighting by measuring the temperature manually with a thermal imaging camera FLIR and illuminance with a LUX meter. The set of power factor, total harmonic distortion, and input power values will be collected automatically through the power quality Analyzer Fluke 345 with a probe Fluke Hall Effect Current. For residential lighting, it was found that both CFL and LED had good performance with the smallest variations in illuminance. Between both, the LED source had the lowest harmonics and the lowest power consumption, on the other hand incandescent bulbs had a bad performance as expected. Public light sources also had a good performance and obtained power factors within the standards, as opposed to the CFL and LED residential sources. The data collected clearly shows the feasibility for nominal voltage reductions. Even with small reductions, there are possibilities of savings which can be passed on to the utilities and consumers

Sistema autônomo de iluminação utilizando energia solar

This work presents a self-sustainable lighting system using ultracapacitor as a storage device, replacing the conventional battery, using solar energy as the only energy supplier. A detailed study of solar panels, switched mode converters and ultracapacitors was made, in order to design a circuit capable of capturing solar energy and transfer it efficiently to a bank of ultracapacitors. Later, at nighttime, this energy is used for lighting in LED luminaires which have high luminous efficiency and high reliability index. This work presents the design of the solar panel, ultracapacitors bank, the development of the voltage converter circuit and charger working at the maximum power point of the solar panel. All subsystems were simulated and it was shown that the use of ultracapacitors is feasible to feed a LED lamp with enough brightness for a person to walk at night, for two night shifts, using a capacitive bank with twenty-four ultracapacitors. Replacing the battery by an ultracapacitor allows a faster recharge, with low maintenance costs, since ultracapacitors have a lifetime bigger than batteries; beyond reducing the environmental impact, as they don't use potentially toxic chemical compounds

Controlo de estufagem do Vinho Madeira em escala piloto

Um dos processos de envelhecimento do Vinho Madeira é a “Estufagem” realizada através da circulação de água aquecida a uma determinada temperatura por um sistema de serpentina existente no interior de cada estufa. De modo a tornar o processo de estufagem eficiente e preservar a qualidade do Vinho Madeira, a monitorização, registo e controlo da temperatura reveste-se da maior importância sendo, atualmente, todo esse processo realizado, por norma, manualmente, quer no sistema de dez estufas de aço inox existente no laboratório de enologia da Universidade da Madeira (UMa), quer nos sistemas das cooperativas de Vinho Madeira. Existem, no mercado, alguns sistemas que solucionam, com menor ou maior limitação, este problema. Porém, nenhum desses sistemas implementa um sistema de controlo “inteligente” capaz de se adaptar automaticamente a diferentes períodos de temperaturas predefinidos e manter o aquecimento das estufas de acordo com essas temperaturas com uma margem de erro inferior a ±0,5℃, bem como o custo associado aos mesmos é elevado o que dificulta a sua implementação neste setor. O sistema implementado, nesta tese, consiste em duas aplicações: uma aplicação web e uma Windows Forms Application. A aplicação web foi desenvolvida em C# com recurso à framework ASP.NET Web Pages e implementa toda a lógica necessária à monitorização gráfica e à gestão do sistema, nomeadamente a definição do setpoint para cada estufa. A Windows Forms Application, também desenvolvida em C# devido à necessidade de interligação com a biblioteca fornecida pela CAREL para conexão aos controladores de temperatura IR32, efetua o registo e controlo automático da temperatura, de acordo com o setpoint definido para cada estufa através da aplicação web. O controlo de temperatura realiza-se com recurso às redes neuronais, nomeadamente através dum controlador DIC (Direct Inverse Controller) que obteve, de entre os vários controladores testados, o melhor Erro Quadrático Médio (MSE) e o melhor Coeficiente de Correlação (R). Através da utilização do sistema implementado conseguiu-se eliminar a limitação física de erro com ± 1℃ em torno do setpoint tendo-se conseguido, para o melhor caso, uma margem de erro de ± 0,1℃ relativamente ao setpoint reduzindo-se, assim, a margem de variação de temperatura até um máximo de 1,8ºC e, consequentemente, o erro associado.

Ação civil pública : taxa de manutenção da iluminação pública; suspensão da cobrança; ilegitimidade ad causum do ministério público ; lei municipal

Inclui jurisprudência

Desenvolvimento e aplicação do índice de desempenho energético da iluminação pública utilizando lógica nebulosa: estudo de caso da Cidade Universitária \"Armando de Salles Oliveira\" da Universidade de São Paulo.

A eficiência e a racionalidade energética da iluminação pública têm relevante importância no sistema elétrico, porque contribui para diminuir a necessidade de investimentos na construção de novas fontes geradoras de energia elétrica e nos desperdícios energéticos. Apresenta-se como objetivo deste trabalho de pesquisa o desenvolvimento e aplicação do IDE (índice de desempenho energético), fundamentado no sistema de inferência nebulosa e indicadores de eficiência e racionalidade de uso da energia elétrica. A opção em utilizar a inferência nebulosa deve-se aos fatos de sua capacidade de reproduzir parte do raciocínio humano, e estabelecer relação entre a diversidade de indicadores envolvidos. Para a consecução do sistema de inferência nebulosa, foram definidas como variáveis de entrada: os indicadores de eficiência e racionalidade; o método de inferência foi baseado em regras produzidas por especialista em iluminação pública, e como saída um número real que caracteriza o IDE. Os indicadores de eficiência e racionalidade são divididos em duas classes: globais e específicos. Os indicadores globais são: FP (fator de potência), FC (fator de carga) e FD (fator de demanda). Os indicadores específicos são: FU (fator de utilização), ICA (consumo de energia por área iluminada), IE (intensidade energética) e IL (intensidade de iluminação natural). Para a aplicação deste trabalho, foi selecionada e caracterizada a iluminação pública da Cidade Universitária \"Armando de Salles Oliveira\" da Universidade de São Paulo. Sendo assim, o gestor do sistema de iluminação, a partir do índice desenvolvido neste trabalho, dispõe de condições para avaliar o uso da energia elétrica e, desta forma, elaborar e simular estratégias com o objetivo de economizá-la.