Simplified design method for energy dissipating devices in retrofitting of seismically isolated bridges

Abstract: Highway bridges have great values in a country because in case of any natural disaster they may serve as lines to save people’s lives. Being vulnerable under significant seismic loads, different methods can be considered to design resistant highway bridges and rehabilitate the existing ones. In this study, base isolation has been considered as one efficient method in this regards which in some cases reduces significantly the seismic load effects on the structure. By reducing the ductility demand on the structure without a notable increase of strength, the structure is designed to remain elastic under seismic loads. The problem associated with the isolated bridges, especially with elastomeric bearings, can be their excessive displacements under service and seismic loads. This can defy the purpose of using elastomeric bearings for small to medium span typical bridges where expansion joints and clearances may result in significant increase of initial and maintenance cost. Thus, supplementing the structure with dampers with some stiffness can serve as a solution which in turn, however, may increase the structure base shear. The main objective of this thesis is to provide a simplified method for the evaluation of optimal parameters for dampers in isolated bridges. Firstly, performing a parametric study, some directions are given for the use of simple isolation devices such as elastomeric bearings to rehabilitate existing bridges with high importance. Parameters like geometry of the bridge, code provisions and the type of soil on which the structure is constructed have been introduced to a typical two span bridge. It is concluded that the stiffness of the substructure, soil type and special provisions in the code can determine the employment of base isolation for retrofitting of bridges. Secondly, based on the elastic response coefficient of isolated bridges, a simplified design method of dampers for seismically isolated regular highway bridges has been presented in this study. By setting objectives for reduction of displacement and base shear variation, the required stiffness and damping of a hysteretic damper can be determined. By modelling a typical two span bridge, numerical analyses have followed to verify the effectiveness of the method. The method has been used to identify equivalent linear parameters and subsequently, nonlinear parameters of hysteretic damper for various designated scenarios of displacement and base shear requirements. Comparison of the results of the nonlinear numerical model without damper and with damper has shown that the method is sufficiently accurate. Finally, an innovative and simple hysteretic steel damper was designed. Five specimens were fabricated from two steel grades and were tested accompanying a real scale elastomeric isolator in the structural laboratory of the Université de Sherbrooke. The test procedure was to characterize the specimens by cyclic displacement controlled tests and subsequently to test them by real-time dynamic substructuring (RTDS) method. The test results were then used to establish a numerical model of the system which went through nonlinear time history analyses under several earthquakes. The outcome of the experimental and numerical showed an acceptable conformity with the simplified method.

Auditoria e identificação de propostas de melhoria no SGA da Funfrap

O compromisso das organizações com as obrigações decretadas ao nível do ambiente, segurança e qualidade emancipa a implementação de Sistemas de Gestão e o processo de auditar. Neste trabalho, decorrente do estágio curricular no âmbito do Mestrado em Engenharia do Ambiente, está evidenciada a importância dos Sistemas de Gestão Ambiental e as razões preponderantes para que sejam auditados. O trabalho pretendeu auditar e avaliar a conformidade do sistema de gestão ambiental, de acordo com a NP EN ISO 14001:2004, de uma indústria de fundição de metais, Funfrap -. Fundição Portuguesa SA, a fim de identificar oportunidades de melhoria no desempenho ambiental da organização. No âmbito do estágio foram ainda realizadas outras atividades, incluindo campanhas de sensibilização, inventário de resíduos sólidos, ferramentas da metodologia World Class Manufacturing, formação sobre a separação de resíduos nos postos de trabalho, acompanhamento de um ensaio na estação de tratamento de águas residuais industriais e apoio para o desenvolvimento do relatório ambiental anual. Da auditoria interna identificaram-se e corrigiram-se nove não conformidades menores e cinco observações. Da auditoria externa foram identificadas apenas duas não conformidades, nenhuma delas relacionadas com as detetadas anteriormente. Além deste resultado foram sugeridas algumas medidas para alcançar um melhor desempenho ambiental da organização.

Influence of the perception of discrimination on women's work motivation

Nowadays, despite anti-discrimination policies, women suffer frequently from a lack of consideration from their male colleagues, altering their well-being and motivation to work. More precisely, perceived personal or groupal discrimination, could have a distinct influence on work motivation. Previous studies showed that the impact on women varies in function of the type of perceived discrimination (Bourguignon et al. 2006). Based on the self-categorization and the social identity theory, work motivation is differently structured as if employees categorized themselves as individuals or as part of a group. As a result, a different impact from personal and group discrimination on work motivation is expected. Moreover, it has been proved that typical men behavior is heavily associated with competence compared to women behavior (Marchand, Saint-Charles & Corbeil, 2007). Therefore, it is hypothesized that women with more masculine traits will suffer from less perceived discrimination, and work motivation. An online survey was created in order to collect data over work motivation, perceived personal and group discrimination. The respondents were also questioned on typical men and women behavior to determine their gender-conformity. To test our hypotheses, data were collected from 57 women stemming from the labour force, aged from 21 to 63 years old. Results indicate that perceived personal discrimination was negatively related to work motivation and that perceived group discrimination was negatively correlated with masculine behavior. Thereby, our study enhances the importance of work environment, and especially discrimination, on work motivation. This research also corroborates the self-categorization and the social identity theory framework to study these issues.

The Role of Feminine and Masculine Norms in College Women's Alcohol Use

Current literature suggests not only that men and women can conform to both feminine and masculine norms, but that women who adhere to certain masculine norms may be at greater risk for problematic alcohol use. This study examined conformity to both masculine and feminine norms, and how conformity to distinct norms influenced heavy episodic drinking and alcohol-related problems among a sample of underage college women (N= 645). Results demonstrated that the masculine norms risk-taking and emotional control were associated with increased HED, while the masculine norm power over women was associated with a decrease in HED. Traditional feminine norms, including modesty and sexual fidelity, were associated with a decrease in HED and alcohol-related problems. The feminine norm relational was associated with increased HED, while the norms thinness and appearance were associated with increased alcohol-related problems. The study’s theoretical and clinical implications are discussed.

Microbiological assessment of indoor air quality at different hospital sites

Poor hospital indoor air quality (IAQ) may lead to hospital-acquired infections, sick hospital syndrome and various occupational hazards. Air-control measures are crucial for reducing dissemination of airborne biological particles in hospitals. The objective of this study was to perform a survey of bioaerosol quality in different sites in a Portuguese Hospital, namely the operating theater (OT), the emergency service (ES) and the surgical ward (SW). Aerobic mesophilic bacterial counts (BCs) and fungal load (FL) were assessed by impaction directly onto tryptic soy agar and malt extract agar supplemented with antibiotic chloramphenicol (0.05%) plates, respectively using a MAS-100 air sampler. The ES revealed the highest airborne microbial concentrations (BC range 240-736 CFU/m(3) CFU/m(3); FL range 27-933 CFU/m(3)), exceeding, at several sampling sites, conformity criteria defined in national legislation [6]. Bacterial concentrations in the SW (BC range 99-495 CFU/m(3)) and the OT (BC range 12-170 CFU/m(3)) were under recommended criteria. While fungal levels were below 1 CFU/m(3) in the OT, in the SW (range 1-32 CFU/m(3)), there existed a site with fungal indoor concentrations higher than those detected outdoors. Airborne Gram-positive cocci were the most frequent phenotype (88%) detected from the measured bacterial population in all indoor environments. Staphylococcus (51%) and Micrococcus (37%) were dominant among the bacterial genera identified in the present study. Concerning indoor fungal characterization, the prevalent genera were Penicillium (41%) and Aspergillus (24%). Regular monitoring is essential for assessing air control efficiency and for detecting irregular introduction of airborne particles via clothing of visitors and medical staff or carriage by personal and medical materials. Furthermore, microbiological survey data should be used to clearly define specific air quality guidelines for controlled environments in hospital settings.

Women at Michigan : the "dangerous experiment," 1870s to the present /

Includes bibliographical references (p. 123-126) and index.

Construir frondoso :uma herança esquecida?

This dissertation of master degree was presented to Post-Graduation Program in Architecture and Planning at UFRN, Brazil. It evaluates 45 one-family housings in the Metropolitan Area of Recife, whose architects consider them to be in conformity with the recommendations contained in Armando de Holanda's book: A Guide to build in the Brazilian Northeast: Architecture as a pleasant place in the sunny tropics , published in 1976 by UFPE. For a long time, it used to be reference in many Architecture and Planning Schools of the Northern Region of Brazil. The research s methodological procedures are based on the Post- Occupancy Evaluation (P.O.E.) with emphasis on the users' thermal comfort of the houses that make part of the sample. Therefore, it has been done technical analyses of the projects, when possible; interviews with the architects; building s inspections; and form applications to the users. The collected data analysis was based on the project recommendations of Holanda s book, they can be synthesized in the principle of Building Leafy". It can not be affirmed that all the houses present the recommendations contained in the guide, but, in many different ways, they exist, sometimes more intensely and sometimes more shyly. However, it can be noticed that in the 45 projects, that the architects perceived the importance of "Building Leafy" on the climatic reality of the Metropolitan Region of Recife

Implementação de um Sistema de Gestão da Qualidade numa Estrutura Residencial para Idosos

Dissertação de Mestrado em Gestão Integrada da Qualidade, Ambiente e Segurança

Espectroscopia no infravermelho e método quimiométrico para a pesquisa de antimicrobianos em leite da microrregião de Pato Branco - PR

Considering the social and economic importance that the milk has, the objective of this study was to evaluate the incidence and quantifying antimicrobial residues in the food. The samples were collected in dairy industry of southwestern Paraná state and thus they were able to cover all ten municipalities in the region of Pato Branco. The work focused on the development of appropriate models for the identification and quantification of analytes: tetracycline, sulfamethazine, sulfadimethoxine, chloramphenicol and ampicillin, all antimicrobials with health interest. For the calibration procedure and validation of the models was used the Infrared Spectroscopy Fourier Transform associated with chemometric method based on Partial Least Squares regression (PLS - Partial Least Squares). To prepare a work solution antimicrobials, the five analytes of interest were used in increasing doses, namely tetracycline from 0 to 0.60 ppm, sulfamethazine 0 to 0.12 ppm, sulfadimethoxine 0 to 2.40 ppm chloramphenicol 0 1.20 ppm and ampicillin 0 to 1.80 ppm to perform the work with the interest in multiresidues analysis. The performance of the models constructed was evaluated through the figures of merit: mean square error of calibration and cross-validation, correlation coefficients and offset performance ratio. For the purposes of applicability in this work, it is considered that the models generated for Tetracycline, Sulfadimethoxine and Chloramphenicol were considered viable, with the greatest predictive power and efficiency, then were employed to evaluate the quality of raw milk from the region of Pato Branco . Among the analyzed samples by NIR, 70% were in conformity with sanitary legislation, and 5% of these samples had concentrations below the Maximum Residue permitted, and is also satisfactory. However 30% of the sample set showed unsatisfactory results when evaluating the contamination with antimicrobials residues, which is non conformity related to the presence of antimicrobial unauthorized use or concentrations above the permitted limits. With the development of this work can be said that laboratory tests in the food area, using infrared spectroscopy with multivariate calibration was also good, fast in analysis, reduced costs and with minimum generation of laboratory waste. Thus, the alternative method proposed meets the quality concerns and desired efficiency by industrial sectors and society in general.

Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants

Background: Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. Methods: A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. Results: The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. Conclusions: It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.

Efeito do revestimento nas propriedades das rolhas de cortiça

A utilização de revestimentos poliméricos em rolhas de cortiça natural é uma prática recorrente na indústria de produção de rolhas. A sua aplicação tem como principal objetivo a melhoria da qualidade visual das rolhas. Contudo, este tratamento altera também as suas caraterísticas de molhabilidade, pelo que é importante otimizar os processos de revestimento de superfície. O presente trabalho teve como objetivo principal a averiguação da influência de um revestimento colorido e de diferentes tratamentos de superfície no comportamento da rolha em garrafa. Foram utilizadas amostras, cedidas pela Cork Supply Portugal, provenientes de quatro branqueamentos distintos (LVL, CSP, CPI e SIL). Foram estudadas amostras com e sem revestimento colorido e, todas elas, tratadas superficialmente com quatro tipos de tratamento (TS1, TS2, TS3 e TS4), sendo as quantidades de parafina e silicone administradas todas diferentes. Para observar o efeito do revestimento colorido e dos tratamentos de superfície nas rolhas de cortiça, procedeu-se a testes para determinação de capilaridade, inserções e forças de extração, simulando as condições de engarrafamento/extração do cliente, de forma a verificar a conformidade dos resultados. Todos estes testes procederam-se nas instalações da CSP. Foram também efetuados testes de molhabilidade pela determinação de ângulos de contacto para três diferentes solventes, nomeadamente água, formamida e diiodometano, e obtidos os Wetting Envelopes, pelo método de OWRK, de forma a prever a molhabilidade das várias amostras. Os procedimentos experimentais descritos efetuaram-se nos laboratórios da Universidade de Aveiro. Aliando as análises aos vários testes efetuados, concluiu-se que o revestimento colorido tem um possível efeito favorecedor nas propriedades mecânicas das rolhas de cortiça, possui maior recetividade aos agentes lubrificantes e maior molhabilidade. Relativamente aos tratamentos de superfície, o melhor, tendo em conta os fatores de molhabilidade, foi o TS4, proporcionando melhor vedação ao vinho. Já a respeito da lubrificação, verificou-se melhores resultados para os tratamentos TS1 e TS2. A lavação SIL apresenta menor afinidade aos agentes vedantes e a CSP possui maior recetibilidade aos agentes lubrificantes.

Coastal zone oil spill modeling

This work presents the development and application of a three-dimensional oil spill model for predicting the movement of an oil slick in the coastal waters of Singapore. In the model, the oil slick is divided into a number of small elements for simulating of the oil processes of spreading, advection, turbulent diffusion. This model is capable of predicting the horizontal movement of surface oil slick. Satellite images and field observations of oil slicks on the surface in the Singapore Straits are used to validate the newly developed model. Compared with the observations, the numerical results of the oil spill model show good conformity. In this study, the 3d model was generated using the geometrical data of Singapore Straits waters by GAMBIT which is a pre-processor of FLUENT programmed.

Legal consideration on Convention for the Prevention of Dumping of Wastes and Other Matter (at sea) and assessment of its implementation in Iran (The London [dumping] Convention)

Making use of sea, as a place for dumping of wastes and other materials from human activities wasn’t forbidden before creation of the convention on the prevention of marine pollution by dumping of wastes and other matters (London Convention). Therefore, industrial countries, without any specific consideration, were dumping their wastes into the world’s seas. Many years and before the beginning of rapid development of industry, the great self- purification of seas were preventing some of discharging problems. But gradually, the increase of industrial development activities, exceeded the production of wastes and other matters, and this led to the misuse of world’s seas and oceans as a dump site. One of the most important consequences of 1972 Stockholm World Conference was to focusing world attention on threats have jeopardized marine environment balance. World countries` leaders committed in Stockholm to begin protecting the environment. Finally, this movement at marine environment section led to the creation of London Convention in the same year. London Convention was concluded for cooperating between countries at December 29, 1972 to promote effective control of all marine environment polluting resources and to prevent marine pollution by dumping wastes and other matters. Then it was opened for signature to other countries. At last, after 15 states signature, this convention was entered in to force at August 30.1975. Ratification and execution of London Convention resulted in coordinated performance of countries in marine waste management. Common actions with supports and cooperation of different international, regional, governmental and non-governmental organizations and agencies prevent marine pollution by dumping of wastes and other matters. Due to the importance of wastes in our marine and coastal areas, investigation of the performance of London Convention can identify the lack of regulations and lack of regulation supports about marine pollution prevention by dumping of wastes and other matters in Iran. Considering this issue, proper protection of seas will be achieved. London Convention has been studied here to achieve intended purposes. In first chapter, generalities about marine environment, including the importance and necessity of marine environment protection, with the focus on some internal and international resources of environmental law accompanying with marine pollution and its recourses, and finally, due to the study theme, dumping of wastes and other matters at seas with its impacts have been investigated .In the section of international measures, a brief history of marine pollution and marine environment international law with international law framework, exclusively for controlling of wastes and other material discharge at seas and oceans has been reviewed. In second chapter, obligations, amendments, and annexes of London Convention have been investigated and classified. The obligations have been categorized in to legal obligations and technical and organizational obligations. In former section, subject ,purpose, territory, exceptions, rights and duties of parties, convention amendments,… and in latter, special requirements for wastes assessment, determination of pollutants` permissible limit, site selection and type of discharge selection, design principles for marine environment quality monitoring program, and discharge license issuance mechanism have been studied. In third chapter, due to the examination of convention performance in Iran, the internal law system for marine environment conservation and its pollution has been mentioned in detail. Considering this, two issues have been compared .firstly, convention obligations with regional treaties that Iran as a party to them and secondly, Iranian internal law there of .Finally, common and different aspects of these issues have been determined. At last, recommendations and strategies for convention enforcement and conformity of its obligations with internal regulations have been presented. Furthermore, translation of convention English text has been reviewed and its protocol has been translated.

Avaliação da conformidade de blocos cerâmicos para alvenaria de vedação produzidas na Região Integrada de Desenvolvimento da Grande Teresina

This research presents an outlook of the industries of red ceramic in the region next to the city of Teresina and an analysis of the ceramic products producted in this pole. The microregion investigated possesses 13 boroughs where were identified 32 ceramic in operation, being that 24 are located in Teresina, the ceramic region more important of Piauí, 1 is located in the city of Miguel Leão and 7 is located in Timon city that belongs to the state of Maranhão. The majority of ceramics are pulverized in these two cities, Teresina and Timon , responsible by a largely production independent of distance between fabric and consumer market. Furthermore, there is an artisanal production realized in other boroughs, mainly manual conformation bricks, where are producted diverse types of handicraft and ceramics utilitarian. The objective of this research is to evalue the conformity of ceramic blocks for brick of obstruction made by red ceramic industry of microregion at studying, verifying their pontentialities and adequacy in terms of production. In this research universe made a search of ceramic industries related to the Foundation CEPRO (Foundation Center of Research Social and Economic of Piauí). For the analysis of the ceramic products , were colected 60 crude bricks sample in three industries for their characterization, and 39 burned bricks sample for the Evaluation of Conformity. The results of the characterization made reached a accetptable standard in all formulations and temperature studied. The burned samples were applied to the geometric, physical and mechanical assays according to the ABNT standards (Brazilian Association of Technical Standards). The results of the physical assays showed that all the samples are at the same band recommended by standard. However, through the geometric assays just two industries did not present results according to the standard, due to lack of control in their process such as in their equipments. Taking into account the mechanical properties, only one industry investigated was not according to the standard

Aplicación de residuos en la fabricación de morteros industriales

La presente Tesis Doctoral estudia el uso de la fracción fina de los residuos de construcción y demolición (RCD) en la fabricación de morteros de albañilería. El principal uso de los áridos reciclados de RCD es la construcción de rellenos o firmes de carreteras, aunque su uso como áridos para la fabricación de hormigones o morteros le daría un mayor valor añadido. A nivel internacional existen numerosos estudios sobre la utilización de la fracción gruesa de los áridos reciclados de RCD en la fabricación de hormigones. Sin embargo son escasos los trabajos llevados a cabo para valorizar la fracción fina. Actualmente en España la fracción fina de los áridos reciclados de RCD está infrautilizada y en la mayoría de los casos depositada sin uso en los vertederos de las Plantas de reciclaje. En este trabajo se han utilizado dos tipos de áridos reciclados, uno procedente de residuos de hormigón (FRCA) y otro de residuos mixtos de tabiquería con un alto porcentaje de ladrillo rojo cerámico (FMRA). Todos los materiales han sido caracterizados desde un punto de vista físico, químico y mineralógico para justificar el efecto de su incorporación a la fabricación de morteros industriales de albañilería. En una primera fase se estudiaron las propiedades del mortero fresco y endurecido fabricado con FRCA y cinco niveles de sustitución volumétrica de arena natural y FRCA: 0%, 5%, 10%, 20% y 40%.Se utilizó un cemento puzolánico tipo CEM-IV y se evaluaron las propiedades a corto y largo plazo de morteros de baja resistencia (M5) En una segunda fase, se utilizó un cemento tipo CEM-II y se fabricaron morteros de mayor resistencia (M-10) utilizando FRMA. En esta etapa se llevaron a cabo sustituciones de arena natural por arena reciclada de 0%, 25%, 50%, 75% y 100%. El residuo fue evaluado medioambientalmente mediante el test de conformidad antes y después de ser ligado con cemento (lixiviación). Los resultados fueron completados con estudios de durabilidad. Con el objetivo de completar los estudios anteriores, se llevó a cabo una tercera fase, donde se sustituyó hasta un 100% de arena natural por FRCA, utilizando un cemento tipo CEM-II para fabricar un mortero tipo M-10, dosificado de manera similar al empleado en la segunda fase de este trabajo. Como conclusión general de esta tesis, se puede decir que pueden admitirse tasas de sustitución de hasta un 50% de arena natural por árido reciclado en morteros industriales de albañilería para usos de interior sin que sus propiedades puedan verse afectadas significativamente. Los resultados obtenidos contribuyen a reducir la extracción de arena natural de canteras y ríos, minimizar el consumo de energía y emisiones de CO2, mitigar el calentamiento global y evitar el depósito en vertedero de la fracción fina de RCD.