Predação, eutrofização e respostas metabólicas em comunidades incrustantes de substratos artificiais na Baía da Ilha Grande, RJ

As comunidades marinhas são afetadas por diversos fatores, que dentro do contexto de estrutura trófica, podem ser divididos em forças bottom-up (forças ascendentes), como por exemplo, a disponibilidade de nutrientes, e forças top-down (forças descendentes), como por exemplo, a predação. Além de modificações na estrutura das comunidades e populações de organismos, essas forças podem influenciar a produção de metabólitos secundários pelos organismos. O presente trabalho teve como objetivo avaliar o efeito das perturbações ambientais geradas pelas manipulações separadas e interativas de exclusão de macropredadores e enriquecimento com nutrientes sobre a estrutura e sobre as respostas metabólicas de comunidades marinhas incrustantes de substratos artificiais no costão rochoso de Biscaia, Baía da Ilha Grande, RJ. O desenho experimental utilizou blocos de concreto como substrato artificial, os quais foram espalhados aleatoriamente na região de infralitoral do costão rochoso. O experimento compreendeu o uso de blocos Controle (ausência de manipulação) e quatro tratamentos, todos com cinco réplicas cada. Os tratamentos foram: tratamento Exclusão de predação (gaiola contra a ação de macropredadores), tratamento Nutriente (sacos de fertilizante de liberação lenta), tratamento Nutriente + exclusão de predação (gaiola contra ação de macropredadores e sacos de fertilizante de liberação lenta) e o tratamento Controle de artefatos (gaiola semifechada para avaliar geração de artefatos). Uma área de 15 x 15 cm do bloco foi monitorada a cada 20 dias, totalizando dez medições. Foram utilizados métodos de monitoramento visual e digital de porcentagem de cobertura por espécie. O enriquecimento com nutrientes foi avaliado através de medições da concentração dos nutrientes Ortofosfato, Nitrato, Nitrito e Amônio na água do entorno do bloco. Para analisar os possíveis artefatos foi realizado experimento de fluxo de água (método Clod card) e a luminosidade dentro das gaiolas foi medida. Os dados demonstraram modificações na estrutura das comunidades bentônicas incrustantes dos substratos artificiais devido às manipulações realizadas, ou seja, pelo enriquecimento com nutrientes, pela exclusão de predação e pela interação entre os dois fatores (Nutriente + exclusão de predação). Além disso, diferenças metabólicas foram detectadas nas substâncias extraídas dos organismos dos diferentes tratamentos do experimento. Esses resultados indicam a existência de controle top-down e bottom-up sobre a comunidade bentônica do local.

Modified sorting technique to mitigate the collateral mortality of trawled school prawns (Metapenaeus macleayi)

The potential for changes to onboard handling practices in order to improve the fate of juvenile school prawns (Metapenaeus macleayi) discarded during trawling were investigated in two Australian rivers (Clarence and Hunter) by comparing a purpose-built, water-filled sorting tray against a conventional dry tray across various conditions, including the range of typical delays before the start of sorting the catch (2 min vs. 15 min). Juvenile school prawns (n= 5760), caught during 32 and 16 deployments in each river, were caged and sacrificed at four times: immediately (T0), and at 24 (T24), 72 (T72), and 120 (T12 0) hours after having been discarded. In both rivers, most mortalities occurred between T0 and T24 and, after adjusting for control deaths (<12%), were greatest for the 15-min conventional treatment (up to 41% at T120). Mixed-effects logistic models revealed that in addition to the sampling time, method of sorting, and delay in sorting, the weight of the catch, salinity, and percentage cloud cover were significant predictors of mortality. Although trawling caused some mortalities and comparable stress (measured as L -lactate) in all school prawns, use of the water tray lessened the negative impacts of some of the above factors across both the 2-min and 15-min delays in sorting so that the overall discard mortality was reduced by more than a third. When used in conjunction with selective trawls, widespread application of the water tray should help to improve the sustainability of trawling for school prawns.

Sensitivity of wear rates in the micro-scale abrasion test to test conditions and material hardness

Micro-scale abrasion (ball cratering) tests were performed with different combinations of ball and bulk specimen materials, under different test conditions, such as load and abrasive slurry concentration. Wear modes were classified into two types: with rolling particle motion and with grooving particle motion. Wear rates observed with rolling particle motion were relatively insensitive to test conditions, whereas with grooving motion they varied much more. It is suggested that rolling abrasion is therefore a more appropriate mode if reproducible test results are desired. The motion of the abrasive particles can be reliably predicted from the knowledge of hardnesses and elastic properties of the ball and the specimen, and from the normal load and the abrasive slurry concentration. General trends in wear resistance measured in the micro-scale abrasion test with rolling particle motion are similar to those reported in tests with fixed abrasives with sliding particle motion, although the variation in wear resistance with hardness is significantly smaller. © 2004 Published by Elsevier B.V.

Sources of variability in the free-ball micro-scale abrasion test

In the 'free-ball' version of the micro-scale abrasion or ball-cratering test the rotating ball rests against a tilted sample and a grooved drive shaft. Tests under nominally identical conditions with different apparatus commonly show small but significant differences in measured wear rate. An indirect method has been developed and demonstrated for continuous on-line measurement of the coefficient of friction in the free-ball test. Experimental investigation of the effects of sample tilt angle and drive shaft groove width shows that both these factors influence the stability of the rotation of the ball, and the shape of the abrasive slurry pool, which in turn affect the coefficient of friction in the wear scar area and the measured wear rate. It is suggested that in order to improve the reproducibility of this method the geometry of the apparatus should be specified. For the apparatus used in this work with a steel ball of 25 mm diameter, a sample tilt angle of 60-75° and a shaft groove width of about 10mm provided the most stable ball motion and a wear rate which showed least variability. © 2004 Elsevier B.V. All rights reserved.

A Test of Computer-assisted Matching Using the North Pacific Humpback Whale, Megaptera novaeangliae, Tail Flukes Photograph Collection

Testing was conducted of a computer-assisted system for matching humpback whale tail flukes photographs. Trials with a 12,000-photographs database found no differences in match success between matching by computer and matching by comparing smaller catalogs ranging in size from 200 to 400 photographs. Tests with a 24,000-photographs database showed that, on average, the first match was found after examining about 130 photographs whether the photograph quality was excellent, good, or poor. Match success did not appear to be strongly related to whether the tail flukes had especially distinctive markings or pigment patterns (recognition quality). An advantage of computer-assisted matching is the ability to compare new photographs to the entire North Pacific collection, where no bias is introduced based on expectation of resightings within or between specific areas, or based on expectation of behavioral role (e.g. matching “known” females to “known” females).