低熔点间同1,2-聚丁二烯热塑性弹性体的研究

本论文对异辛酸铁(Fe)-亚磷酸二乙酯(P)-三异丁基铝/三乙基铝(Al)催化体系进行研究, 合成熔点低于130℃的间同1,2-聚丁二烯热塑性弹性体,并且发现三异丁基铝与三乙基铝比例对聚合活性有较大的影响。放大实验合成的间同1,2-聚丁二烯熔点为126℃ ,其1,2-结构含量为84%,间同度为81%；数均分子量13万,重均分子量40万,分子量分布为3.0；300%定伸应力为14.2MPa,拉伸强度20.5MPa,扯断伸长率420%,断裂强度20.4MPa,硬度为94邵尔A,热分解温度435℃,具有良好的力学性能和热稳定性。

Why [6,6]- and 1,2-Benzal-3-N-4-O-Cyclic Phenylimidate C-60 Undergo Electrochemically Induced Retro-Addition Reactions while 1,4-Dibenzyl-2,3-Cyclic Phenylimidate C-60 Does Not? C-H center dot center dot center dot X (X = N, O) Intramolecular Interactions in Organofullerenes

The electrochemical properties of a series of structurally related fullerooxazoles, [6,6] cyclic phenylimidate C-60 (1), 1,2-benzal-3-N-4-O-cyclic phenylimidate C-60 (2), and 1,4-dibenzyl-2,3-cyclic phenylimidate C-60 (3), are described, and the spectroscopic characterizations of their anionic species are reported. The results show that compounds I and 2 undergo retro-cycloaddition reactions that lead to the formation of C-60 and C61HPh, respectively, upon two-electron-transfer reduction. However, compound 3 demonstrates much more electrochemical stability as no retro-cycloaddition reaction occurs under similar conditions. Natural bond orbital (NBO) calculations on charge distribution show there is no significant difference among the dianions of 1, 2, and 3, indicating that the electrochemical stability of 3 is unlikely to be caused by the charge distribution difference of the dianions of three compounds. Examination on the crystal structure of compound 3 reveals close contacts of the C-H group with the heteroatoms (N and O) of cyclic phenylimidate, suggesting the existence of C-H center dot center dot center dot X (X = N, O) intramolecular hydrogen bonding among the addends, which is further confirmed by NBO analysis.

PP／间同1,2-聚丁二烯的物理力学性能

添加不同质量分数的间同1,2-聚丁二烯(sPB)热塑性弹性体对聚丙烯(PP)共混改性,研究了共混体系的物理力学性能。PP与sPB结构相似,有良好的相容性,随着w(sPB)从0增至40%,共混体系的屈服拉伸强度、弯曲模量及耐热性有所降低;悬臂梁冲击强度增加,且常温悬臂梁冲击强度增幅较大,但低温悬臂梁冲击强度增加较少;断裂伸长率和熔体流动速率先增加后减少。

Facilitated ion-transfer of sodium cation by (anthraquinone-1-yloxy) methane-15-crown-5 across the water/1,2-dichloroethane microinterface

The transfer of sodium cation facilitated by (anthraquinone-1-yloxy) methane-15-crown-5(L) has been investigated at the water/1,2-dichloroethane microinterface supported at the tip of a micropipette. The diffusion coefficient of (anthraquinone-1-yloxy) methane-15-crown-5 obtained was (3.42 +/- 0.20) x 10(-6) cm(2) s(-1). The steady-state voltammograms were observed for forward and backward scans due to sodium ion transfer facilitated by L with 1:1 stoichiometry. The mechanism corresponded to an interfacial complexation (TIC) and interfacial dissociation (TID) process. The association constant was calculated to be log beta(o) = 11.08 +/- 0.03 in the DCE phase. The association constant of other alkali metals (Li+, K+, Rb+) were also obtained.

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

成核剂1,3:2,4-二(亚苄基)-D山梨醇对PET/PEN共混体系结构和结晶形态影响

利用差示扫描量热仪、X射线衍射仪、正交偏光显微镜研究了成核剂 1,3 :2 ,4-二 (亚苄基 ) -D山梨醇(DBS)对聚对苯二甲酸乙二醇酯 (PET) /聚 2 ,6-萘二甲酸乙二醇酯 (PEN)共混体系的结构及结晶形态的影响。结果表明 :成核剂的加入 ,使PET/PEN共混体系熔融起始温度升高 10℃左右 ,结晶峰形变尖锐 ,说明加入成核剂后有效促进了PET/PEN共混体系的结晶。实验结果表明 :成核剂含量低于 1%时 ,PET/PEN共混体系晶体的球晶完整。成核剂含量大于 3 %时 ,PET/PEN /DBS共混体系晶体的球晶碎小。成核剂的加入 ,能够有效地减小球晶尺寸和降低球晶的完善性

catena-Poly[[[2-(2-furyl)-1H-imidazo[4,5-f][1,10]phenanthroline]zinc(II)]-mu-benzene-1,2-dicarboxylato]

In the title compound, [Zn(C8H4O4)(C17H10N4O)](n), the Zn-II atom is five-coordinated by two N atoms from the phenanthro-line-derived ligand and three O atoms from one bidentate and one monodentate benzene-1,2-dicarboxylate (1,2-BDC) dianions in a distorted trigonal-bipyramidal geometry. The Zn-II atoms are bridged by the 1,2-BDC ligands to form a single-chain structure. Neighboring chains interact through pi-pi interactions, leading to a two-dimensional network.

填充油的种类对Fe系1,2-聚丁二烯性能的影响

研究了芳烃油和环烷烃油对充油铁系1,2-聚丁二烯橡胶性能的影响。结果表明,基础胶充油后门尼粘度值下降,可塑性增加,混炼行为变佳;填充芳烃油比填充环烷烃油的橡胶在拉伸强度、撕裂强度、伸长率和生胶门尼值等方面均有所提高;充油后虽然硫化胶硬度降低,但是生热和耐磨性能提高。填充芳烃油可适当提高硫化胶的抗湿滑性,但滚动阻力也升高。环烷烃油可降低硫化胶的滚动阻力。充油可适当改善胶料的抗老化性能。

间同立构1,2-聚丁二烯的合成和形态结构研究

间同立构1,2-聚丁二烯自1955年问世以来 ,引起人们的广泛关注 ,但绝大多数研究工作集中在聚合物的合成方面[1～3] ,对其形态结构方面的研究却很少报道[4] ,原因是该聚合物分子侧链含有大量双链 ,在较高温度下 (>150℃ )很容易产生热交联 ,这给结构研究造成了很大困难 .间同立构1,2-聚丁二烯的性能取决于间规度 ,低间规度聚合物呈现弹性体特征 ,而高间规度聚合物则是一种半结晶性塑料 ,其结晶为平面锯齿链正交堆砌 ,Pacm空间群[4] .本文采用一种新的催化体系 ,使合成的1,2-聚丁二烯间规度可以调控.同时首次报道了结晶性间规1,2-聚丁二烯稀溶液浇铸薄膜形成具有单晶取向的板条状片层结构,并应用电子显微学和电子衍射技术确定其晶体结构.1.实验部分1.1样品及试剂　乙酰基丙酮铁 [(Fe(acac) 3)纯度为 99.9% ],使用时配成0.2mol/ L的甲苯溶液 ;三异丁基铝 [Al(i-Bu) 3]由 Aldrich公司提供 ;氢化亚磷酸二乙酯 (DEP)及丁二烯由锦州化学公司提供 ;丁二烯通过蒸馏进行纯化 ;己烷使用前在 Na/ K合金...

结晶性间同立构1,2-聚丁二烯的单晶结构

近十几年来,结晶性间同立构1,2-聚丁二烯引起人们的广泛关注,但绝大多数研究工作集中在聚合物的制备、物理性质和应用方面[1～3],对于其结晶行为和晶体结构则未见报道 .原因是间同立构1,2-聚丁二烯分子侧链含有大量的双键,在较高温度下很容易交联 ,特别是高间规度的聚合物 ,由于其熔融温度高 (>200℃ )则更易产生交联,这给结晶行为和结构研究带来很大困难.结晶性间同立构1,2-聚丁二烯的晶体结构为平面锯齿链正交堆砌,Pacm空间群[4].我们曾报道了结晶性间同立构1,2-聚丁二烯的合成和溶液浇铸膜的板条状结构[5],本文采用薄膜熔体结晶的方法第一次成功地获得了间同立构1,2-聚丁二烯的单晶,并通过电子显微学和电子衍射技术确定了其晶体结构.1 实验部分1.1间同立构1,2-聚丁二烯的制备采用乙酰基丙酮铁 [Fe(acac) ]3、三异丁基铝 [Al(i-Bu)3]和氢化亚磷酸二乙酯 (DEP)的新催化体系制备间同立构1,2-聚丁二烯,具体合成路线参见文献 [5].本文所选用聚合物的1,2单元含量为 89.3 % ,间规度为 ...

Novel two-dimensional sodium molybdenum phosphates containing {M(enMe)(2)}(2+) bridging groups (M = Ni, Cu; enMe=1,2-diaminopropane)

Two novel organic-inorganic hybrid compounds, (H(2)enMe)(4)(H3O)[Ni(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (1) and (H(2)enMe)(4)(H3O)[Cu(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (2) (enMe = 1,2-diaminopropane), have been hydrothermally synthesized and characterized by elemental analyses, IR, EPR, XPS, UV-Vis spectra and TG analyses. Single crystal X-ray diffraction shows that 1 and 2 are isostructural compounds. Both the compounds exhibit an unusual two-dimensional (2-D) window-like network consisting of one-dimensional (1-D) chains of sodium molybdenum phosphate anions connected by transition metal coordination complexes cations. Compound 1 and 2 represent the first 2-D molybdenum phosphate skeleton pillared by transition metal complex fragments.

Novel hydrogen-bonded three-dimensional networks encapsulating one-dimensional covalent chains: [M(4,4 '-bipy)(H2O)4](4-abs)2 center dot nH(2)O (4,4 '-bipy=4,4 '-Bipyridine; 4-abs=4-aminobenzenesulfonate) (M=Co, n=1; M=Mn, n=2)

Two novel compounds, [Co(4,4'-bipy)(H2O)(4)](4-abS)(2).H2O (1) and [Mn(4,4'-bipy)(H2O)(4)](4-abs)(2).2H(2)O (2) (4,4'-bipy = 4,4'-bipyridine; 4-abs = 4-aminobenzenesulfonate), have been synthesized in aqueous solution and characterized by single-crystal X-ray diffraction, elemental analyses, UV-vis and IR spectra, and TG analysis. X-ray structural analysis revealed that 1 and 2 both possess unusual hydrogen-bonded three-dimensional (3-D) networks encapsulating one-dimensional (1-D) covalently bonded infinite [M(4,4'-bipy)(H2O)(4)](2+) (M = Co, Mn) chains. The 4-abs anions in 1 form 1-D zigzag chains through hydrogen bonds. These chains are further extended through crystallization water molecules into 3-D hydrogen-bonded networks with 1-D channels, in which the [Co(4,4'-bipy)(H2O)(4)](2+) linear covalently bonded chains are located. Crystal data for 1: C22H30CoN4O11S2, monoclinic P2(1), a = 11.380(2) Angstrom, b = 8.0274(16) Angstrom, c = 15.670(3) Angstrom, alpha = gamma = 90degrees, beta = 92.82(3)degrees, Z = 2. Compound 2 contains interesting two-dimensional (2-D) honeycomb-like networks formed by 4-abs anions and lattice water molecules via hydrogen bonding, which are extended through other crystallization water molecules into three dimensions with 1-D hexagonal channels. The [Mn(4,4'-bipy)(H2O)(4)](2+) linear covalent chains exist in these channels. Crystal data for 2: C22H32WN4O12S2, monoclinic P2(1)/c, a = 15.0833(14) Angstrom, b = 8.2887(4) Angstrom, c = 23.2228(15) Angstrom, alpha = gamma = 90degrees, beta = 95.186(3)degrees, Z = 4.

Alkali metal ions transfer across a water/1,2-dichloroethane interface facilitated by a novel monoaza-B15C5 derivative

In this paper, a novel monoaza-B15C5 derivative, N-(2-tosylamino)-isopentyl-monoaza-15-crown-5 (L), is used as an ionophore to facilitate alkali metal cations transfer across a water/1,2-dichloroethane (W/DCE) interface. Well-defined voltammetric behaviors are observed at the polarized W/DCE interfaces supported at micro- and nano-pipets except Cs+. The diffusion coefficient of this ionophore in the DCE phase is calculated to be equal to (3.3+/-0.2) x 10(-6) cm(2) s(-1). The experimental results indicate that a 1:1 (metal: ionophore) complex is formed at the interface with a TIC/TID mechanism. The selectivity of this ionophore towards alkali ions follows the sequence Na+ > Li+ > K+ > Rb+ > Cs+. The logarithm of the association constants (log beta(1)(0)) of the LiL+, NaL+, KL+ and RbL+ complexes in the DCE phase are calculated to be 10.6, 11.6, 9.0 and 7.1, respectively. The kinetic parameters are determined by steady-state voltammograms using nanopipets. The standard rate constants (k(0)) for Li+, Na+, K+ and Rb+ transfers facilitated by L are 0.54+/-0.05, 0.63+/-0.09, 0.51+/-0.04 and 0.46+/-0.06 cm s(-1), respectively. The pH values of aqueous solution have little effect on the electrochemical behaviors of these facilitated processes. The results predicate that this new type of ionophore might be useful to fabricate electrochemical sensor of sodium ion.

Dinuclear half-sandwich complexes containing bridging 1,2-dicarba-closo-dodecaborane-1,2-dichalcogenolato ligands. Molecular structures of Cp2Fe2(CO)(3)[mu-Se2C2(B10H10)], Cp2Ru2[mu-S2C2(B10H10)](2), and CP*Ru-2(2)(mu-Se)[mu-Se2C2(B10H10)].

Three prototypes of dinuclear complexes were obtained from the reactions of dilithium 1,2-dicarbacloso-dodecaborane-1,2-dichalcogenolates, (B10H10)C-2-(ELi)(2) (E = S, Se), with CpFe(CO)(2)Cl (1), CpRu(PPh3)(2)Cl (2), or [Cp*RuCl2](2) (3), respectively, and their structures have been determined by X-ray crystallography.

Hydrothermal synthesis and characterization of bimetallic cluster complex [{Mn(phen)(2)}(2)V4O12]center dot 1/2 H2O

A new bimetallic cluster complex with the formula [(Mn(phen)(2))(2)V4O12].1/2 H2O has been synthesized through hydrothermal reaction of vanadate staring material with manganese cation in the presence of nitrogen donor chelating ligand and characterized by single-crystal X-ray diffraction, elemental analysis, IR UV-vis, ESR spectrum and thermal analysis. The compound crystallize in the monoclinic space group P2(1)/c with a = 18.475(4) Angstrom, b = 11.473(2) Angstrom, c = 23.667(5) Angstrom, beta = 97.76(3)degrees, V = 4971(2) Angstrom(3) and Z = 4. The structure of [{Mn(phen)(2)}(2)V4O12].1/2 H2O is composed of a discrete V4O124- cluster covalently attached to two [Mn(phen)(2)](2+) fragments.