Three band-gap QW intermixing in InP/InGaAs/InGaAsP system for monolithically integrated optical switch

Quantum well intermixing is a key technique for photonic integration. The intermixing of InP/InGaAs/InGaAsP material involving the deposition of a layer of sputtered SiO2 on the semiconductor surface, followed by thermal annealing has allowed good control of the intermixing process and has been used to fabricate extended cavity lasers. This will be used for optimization of the performance of optical switches consisting of passive components, modulators and amplifiers.

High bandwidth optical links over multimode fibre

A Fabry-Perot laser source operating at 1300 nm was modulated at 2.5 Gb/s with a 27-1 pseudo-random bit sequence. Three techniques were examined for increasing the bandwidth of optical links using multimode fiber (MMF). With an offset launch of 14 μm, the eye remained open after the 2 km link of 50 μm core MMF containing seven connectors and three splices. An approximate four-fold bandwidth improvement was obtained using the offset launch with a bandwidth-length product of 7.5 Gb/s.km and a bit error rate below 10-10. The bandwidth enhancement was stable against environmental influences on the fiber link, such as mechanical agitation. Detailed simulations demonstrated that the technique allows enhanced operating bandwidths in over 99% of existing link.

Performance of single mode laser components using 2D photonic lattice reflectors

This paper will report studies of the placement of 2D photonic gratings on either side of the ridge in a Fabry Perot laser device in order to cause single mode emission. Using this approach, side mode suppression ratios of up to 30 dB are achieved, the emission remaining single mode even under 10 Gb/s large signal modulation. It is found that the use of the grating not only causes spectrally dependent reflection but in addition can lead to transverse mode fluctuations. The action of the grating has been studied not just in terms of its edge emission where conversion of the transverse modes is achieved, but also through measurement of the vertical emission from the structure where strong filtering action is observed.

Amorphous silicon display backplanes on plastic substrates

Amorphous silicon thin-film transistors and pixel driver circuits for organic light-emitting diode displays have been fabricated on plastic substrates. Pixel circuits demonstrate sufficient current delivery and long-term stable operation. © 2005 IEEE.

Structural and optical properties of III-V nanowires and nanowire heterostructures grown by metalorganic chemical vapour deposition

We have investigated the structural and optical properties of III-V nanowires grown by metalorganic chemical vapour deposition. Binary GaAs, InAs and InP nanowires, and ternary InGaAs and AlGaAs nanowires, have been fabricated and characterised. A variety of axial and radial heterostructures have also been fabricated, including GaAs/AlGaAs core-multishell and GaAs/InGaAs superlattice nanowires. GaAs/AlGaAs core-shell nanowires exhibit strong photoluminescence as the AlGaAs shell passivates the GaAs nanowire surface reducing the surface nonradiative recombination. © 2007 IEEE.

Growth of GaAs/InAs vertical nanowires on GaAs (111)B by metalorganic chemical vapor deposition

The growth mechanism and properties of GaAs/InAs nanowires prepared by metalorganic chemical vapor deposition are investigated. Vertical InAs nanowires on GaAs (111)B substrates are successfully grown despite the large lattice mismatch (-7.2%). The crystallographic perfection of InAs nanowires is confirmed by hexagonal or triangular cross section. An interesting L-shaping of GaAs/InAs heterostructure nanowire which could be useful for novel device application is observed. © 2005 IEEE.

Characteristics of triangle and square InP/InGaAsP microlasers

Directional emission triangle and square InGaAsP/InP lasers have been fabricated by standard photolithography, inductively coupled plasma etching technique combined with wet chemical etching process. In this article, the characteristics of the microcavity lasers are presented. For an equilateral triangle microcavity laser with the side length of 30 mu m, we got the laser spectra fitted very well with the mode wavelength formulate LIP to the 8(th) transverse mode at room temperature. But the laser spectra are usually more complex than the formulae for the lasers, especially for the lasers with a smaller side length. For a square microcavity laser with side length of 20 mu m, we observed the mode competition between the Fabry-Perot (FP) modes and Whispering-Gallery (WG) modes at 200K. The output spectra below the threshold have the mode interval of FP modes with a large mode interval, and the laser spectra agree very well with the WG modes, which have mode interval less than the FP modes. The output spectra are dominated by the FP modes below the threshold, because the FP modes have a higher output coupling efficiency than the WG modes.

Subretinal implantable micro photodetector array

A subretinal implant device, Micro Photo Diode Array, which can partly imitate the function of photoreceptor cells, was presented. Process to fabricate the MPDA and characteristics of the MPDA in vivo were described.

Investigation of vertical radiation loss for whispering-gallery modes in 3-D microresonators by FDTD simulation

The vertical radiation loss of three-dimensional (3-D) microresonators is investigated by 3-D finite-difference time-domain (FDTD) simulation. The simulation shows that the vertical radiation causes an important loss in the microresonators with weak waveguiding, and result in decrease of the quality factors (Q-factors) of whispering-gallery (WG) modes. Through the simulation, we find that TM-like modes have much weaker vertical radiation loss than TE-like modes. High Q-factor TM-like modes are observed in the 3-D microresonators with weak vertical waveguiding, but the Q-factors of TE-like modes decrease greatly.

Continuous-wave electrically injected InP/GaInAsP equilateral-triangle-resonator lasers

Equilateral-triangle-resonator (ETR) microlasers with an output waveguide connected to one of the vertices of the ETR are fabricated using standard photolithography and inductively-coupled-plasma etching techniques. Continuous-wave electrically injected 1550 nm ETR laser with side length ranged from 15 to 30 tm are realized at room temperature.

High-quality-factor EH modes in microcylinder resonators predicted by 3D FDTD simulation

The mode characteristis of a microcylinders with center layer thickness 0.2 mu m and radius 1 mu m are investigated by the three-dimensional (31)) finite-difference time-domain (FDTD) technique and the Pade approximation. The mode quality factor (Q-factor) of the EH71 mode obtained by 3D FDTD increase with the increase of the refractive index of the cladding layer n(2) as n(2) smaller than 3.17, and can be as large as 2.4 x 10(4) as the vertical refractive index distribution is 3.17/3.4/3.17, which is much larger than that of the HE71 mode with the same vertical refractive index distribution.

Growth mechanism of InGaAlAs waveguides by narrow stripe selective MOVPE

Growth mechanism of InGaAlAs waveguides by narrow stripe selective MOVPE has been studied. Both the InGaAlAs bulk waveguides and the InGaAlAs MQW waveguides were successful grown on the patterned substrates at optimized growth conditions. The mask stripe width varied from 0 to 40 mu m, while the window region width between a pair of mask stripes was fixed 2.5 mu m. These selectively grown waveguides were covered by specific InP layers, which can keep the InGaAlAs waveguides from being oxidized during the fabrication of devices. In particular, there exhibit strong dependences of the photoluminescence (PL) spectrum on the mask stripe width for the samples. The results were explained in considering both the migration effect from a masked region (MMR) and the lateral vapor diffusion effect (LVD).