Maailman ennen teknisen käyttöiän päättymistä pysäytetyt ydinvoimahankkeet

Tämän kandidaatintyön tarkoituksena on selvittää maailman tämän hetkinen tilanne ydinvoimalahankkeista, jotka on rakennettu ja olleet käytössä, mutta suljettu ennenaikaisesti. Mukaan otetaan reaktorit, joiden käyttöikää ei ole jatkettu vaikka se teknisesti olisi ollut mahdollista. Tarkasteluun otetaan vain kaupalliseen käyttöön tarkoitetut tehoreaktorit. Koereaktorit, prototyypit ja pienet esittelyreaktorit jätetään tarkastelun ulkopuolelle, koska niiden käyttöikä ja tarkoitus ei välttämättä ole määriteltävissä. Tarkastelun ulkopuolelle jätetään myös reaktorit, jotka ovat tuhoutuneet onnettomuuden takia.

Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Modelling of hydrogen stratification and gas mixing in containment using the APROS code

Hydrogen stratification and atmosphere mixing is a very important phenomenon in nuclear reactor containments when severe accidents are studied and simulated. Hydrogen generation, distribution and accumulation in certain parts of containment may pose a great risk to pressure increase induced by hydrogen combustion, and thus, challenge the integrity of NPP containment. The accurate prediction of hydrogen distribution is important with respect to the safety design of a NPP. Modelling methods typically used for containment analyses include both lumped parameter and field codes. The lumped parameter method is universally used in the containment codes, because its versatility, flexibility and simplicity. The lumped parameter method allows fast, full-scale simulations, where different containment geometries with relevant engineering safety features can be modelled. Lumped parameter gas stratification and mixing modelling methods are presented and discussed in this master’s thesis. Experimental research is widely used in containment analyses. The HM-2 experiment related to hydrogen stratification and mixing conducted at the THAI facility in Germany is calculated with the APROS lump parameter containment package and the APROS 6-equation thermal hydraulic model. The main purpose was to study, whether the convection term included in the momentum conservation equation of the 6-equation modelling gives some remarkable advantages compared to the simplified lumped parameter approach. Finally, a simple containment test case (high steam release to a narrow steam generator room inside a large dry containment) was calculated with both APROS models. In this case, the aim was to determine the extreme containment conditions, where the effect of convection term was supposed to be possibly high. Calculation results showed that both the APROS containment and the 6-equation model could model the hydrogen stratification in the THAI test well, if the vertical nodalisation was dense enough. However, in more complicated cases, the numerical diffusion may distort the results. Calculation of light gas stratification could be probably improved by applying the second order discretisation scheme for the modelling of gas flows. If the gas flows are relatively high, the convection term of the momentum equation is necessary to model the pressure differences between the adjacent nodes reasonably.

Target audience analysis in cyber domain

This thesis aims to find an effective way of conducting a target audience analysis (TAA) in cyber domain. There are two main focal points that are addressed; the nature of the cyber domain and the method of the TAA. Of the cyber domain the object is to find the opportunities, restrictions and caveats that result from its digital and temporal nature. This is the environment in which the TAA method is examined in this study. As the TAA is an important step of any psychological operation and critical to its success, the method used must cover all the main aspects affecting the choice of a proper target audience. The first part of the research was done by sending an open-ended questionnaire to operators in the field of information warfare both in Finland and abroad. As the results were inconclusive, the research was completed by assessing the applicability of United States Army Joint Publication FM 3-05.301 in the cyber domain via a theory-based content analysis. FM 3- 05.301 was chosen because it presents a complete method of the TAA process. The findings were tested against the results of the questionnaire and new scientific research in the field of psychology. The cyber domain was found to be “fast and vast”, volatile and uncontrollable. Although governed by laws to some extent, the cyber domain is unpredictable by nature and not controllable to reasonable amount. The anonymity and lack of verification often present in the digital channels mean that anyone can have an opinion, and any message sent may change or even be counterproductive to the original purpose. The TAA method of the FM 3-05.301 is applicable in the cyber domain, although some parts of the method are outdated and thus suggested to be updated if used in that environment. The target audience categories of step two of the process were replaced by new groups that exist in the digital environment. The accessibility assessment (step eight) was also redefined, as in the digital media the mere existence of a written text is typically not enough to convey the intended message to the target audience. The scientific studies made in computer sciences and both in psychology and sociology about the behavior of people in social media (and overall in cyber domain) call for a more extensive remake of the TAA process. This falls, however, out of the scope of this work. It is thus suggested that further research should be carried out in search of computer-assisted methods and a more thorough TAA process, utilizing the latest discoveries of human behavior. ---------------------------------------------------------------------------------------------------------------------------------- Tämän opinnäytetyön tavoitteena on löytää tehokas tapa kohdeyleisöanalyysin tekemiseksi kybertoimintaympäristössä. Työssä keskitytään kahteen ilmiöön: kybertoimintaympäristön luonteeseen ja kohdeyleisöanalyysin metodiin. Kybertoimintaympäristön osalta tavoitteena on löytää sen digitaalisesta ja ajallisesta luonteesta juontuvat mahdollisuudet, rajoitteet ja sudenkuopat. Tämä on se ympäristö jossa kohdeyleisöanalyysiä tarkastellaan tässä työssä. Koska kohdeyleisöanalyysi kuuluu olennaisena osana jokaiseen psykologiseen operaatioon ja on onnistumisen kannalta kriittinen tekijä, käytettävän metodin tulee pitää sisällään kaikki oikean kohdeyleisön valinnan kannalta merkittävät osa-alueet. Tutkimuksen ensimmäisessä vaiheessa lähetettiin avoin kysely informaatiosodankäynnin ammattilaisille Suomessa ja ulkomailla. Koska kyselyn tulokset eivät olleet riittäviä johtopäätösten tekemiseksi, tutkimusta jatkettiin tarkastelemalla Yhdysvaltojen armeijan kenttäohjesäännön FM 3-05.301 soveltuvuutta kybertoimintaympäristössä käytettäväksi teorialähtöisen sisällönanalyysin avulla. FM 3-05.301 valittiin koska se sisältää kokonaisvaltaisen kohdeyleisöanalyysiprosessin. Havaintoja verrattiin kyselytutkimuksen tuloksiin ja psykologian uusiin tutkimuksiin. Kybertoimintaympäristö on tulosten perusteella nopea ja valtava, jatkuvasti muuttuva ja kontrolloimaton. Vaikkakin lait hallitsevat kybertoimintaympäristöä jossakin määrin, on se silti luonteeltaan ennakoimaton eikä sitä voida luotettavasti hallita. Digitaalisilla kanavilla usein läsnäoleva nimettömyys ja tiedon tarkastamisen mahdottomuus tarkoittavat että kenellä tahansa voi olla mielipide asioista, ja mikä tahansa viesti voi muuttua, jopa alkuperäiseen tarkoitukseen nähden vastakkaiseksi. FM 3-05.301:n metodi toimii kybertoimintaympäristössä, vaikkakin jotkin osa-alueet ovat vanhentuneita ja siksi ne esitetään päivitettäväksi mikäli metodia käytetään kyseisessä ympäristössä. Kohdan kaksi kohdeyleisökategoriat korvattiin uusilla, digitaalisessa ympäristössä esiintyvillä ryhmillä. Lähestyttävyyden arviointi (kohta 8) muotoiltiin myös uudestaan, koska digitaalisessa mediassa pelkkä tekstin läsnäolo ei sellaisenaan tyypillisesti vielä riitä halutun viestin välittämiseen kohdeyleisölle. Tietotekniikan edistyminen ja psykologian sekä sosiologian aloilla tehty tieteellinen tutkimus ihmisten käyttäytymisestä sosiaalisessa mediassa (ja yleensä kybertoimintaympäristössä) mahdollistavat koko kohdeyleisöanalyysiprosessin uudelleenrakentamisen. Tässä työssä sitä kuitenkaan ei voida tehdä. Siksi esitetäänkin että lisätutkimusta tulisi tehdä sekä tietokoneavusteisten prosessien että vielä syvällisempien kohdeyleisöanalyysien osalta, käyttäen hyväksi viimeisimpiä ihmisen käyttäytymiseen liittyviä tutkimustuloksia.

Building Dynamic Data Centers for Fast Delivery of New Data and Data Updates

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Stock Market reaction to the CSR announcements of American fast food companies

The purpose of this study is to examine whether Corporate Social Responsibility (CSR) announcements of the three biggest American fast food companies (McDonald’s, YUM! Brands and Wendy’s) have any effect on their stock returns as well as on the returns of the industry index (Dow Jones Restaurants and Bars). The time period under consideration starts on 1st of May 2001 and ends on 17th of October 2013. The stock market reaction is tested with an event study utilizing CAPM. The research employs the daily stock returns of the companies, the index and the benchmarks (NASDAQ and NYSE). The test of combined announcements did not reveal any significant effect on the index and McDonald’s. However the stock returns of Wendy’s and YUM! Brands reacted negatively. Moreover, the company level analyses showed that to their own CSR releases McDonald’s stock returns respond positively, YUM! Brands reacts negatively and Wendy’s does not have any reaction. Plus, it was found that the competitors of the announcing company tend to react negatively to all the events. Furthermore, the division of the events into sustainability categories showed statistically significant negative reaction from the Index, McDonald’s and YUM! Brands towards social announcements. At the same time only the index was positively affected by to the economic and environmental CSR news releases.

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Let Go and Remember. How Finnish Communities Experienced and Memorialized School Shootings

This study examines the aftermath of mass violence in local communities. Two rampage school shootings that occurred in Finland are analyzed and compared to examine the ways in which communities experience, make sense of, and recover from sudden acts of mass violence. The studied cases took place at Jokela High School, in southern Finland, and at a polytechnic university in Kauhajoki, in western Finland, in 2007 and 2008 respectively. Including the perpetrators, 20 people lost their lives in these shootings. These incidents are part of the global school shooting phenomenon with increasing numbers of incidents occurring in the last two decades, mostly in North America and Europe. The dynamic of solidarity and conflict is one of the main themes of this study. It builds upon previous research on mass violence and disasters which suggests that solidarity increases after a crisis, and that this increase is often followed by conflict in the affected communities. This dissertation also draws from theoretical discussions on remembering, narrating, and commemorating traumatic incidents, as well as the idea of a cultural trauma process in which the origins and consequences of traumas are negotiated alongside collective identities. Memorialization practices and narratives about what happened are vital parts of the social memory of crises and disasters, and their inclusive and exclusive characteristics are discussed in this study. The data include two types of qualitative interviews; focused interviews with 11 crisis workers, and focused, narrative interviews with 21 residents of Jokela and 22 residents of Kauhajoki. A quantitative mail survey of the Jokela population (N=330) provided data used in one of the research articles. The results indicate that both communities experienced a process of simultaneous solidarity and conflict after the shootings. In Jokela, the community was constructed as a victim, and public expressions of solidarity and memorialization were promoted as part of the recovery process. In Kauhajoki, the community was portrayed as an incidental site of mass violence, and public expressions of solidarity by distant witnesses were labeled as unnecessary and often criticized. However, after the shooting, the community was somewhat united in its desire to avoid victimization and a prolonged liminal period. This can be understood as a more modest and invisible process of “silent solidarity”. The processes of enforced solidarity were partly made possible by exclusion. In some accounts, the family of the perpetrator in Jokela was excluded from the community. In Kauhajoki, the whole incident was externalized. In both communities, this exclusion included associating the shooting events, certain places, and certain individuals with the concept of evil, which helped to understand and explain the inconceivable incidents. Differences concerning appropriate emotional orientations, memorialization practices and the pace of the recovery created conflict in both communities. In Jokela, attitudes towards the perpetrator and his family were also a source of friction. Traditional gender roles regarding the expression of emotions remained fairly stable after the school shootings, but in an exceptional situation, conflicting interpretations arose concerning how men and women should express emotion. The results from the Jokela community also suggest that while increased solidarity was seen as important part of the recovery process, some negative effects such as collective guilt, group divisions, and stigmatization also emerged. Based on the results, two simultaneous strategies that took place after mass violence were identified; one was a process of fast-paced normalization, and the other was that of memorialization. Both strategies are ways to restore the feeling of security shattered by violent incidents. The Jokela community emphasized remembering while the Kauhajoki community turned more to the normalization strategy. Both strategies have positive and negative consequences. It is important to note that the tendency to memorialize is not the only way of expressing solidarity, as fast normalization includes its own kind of solidarity and helps prevent the negative consequences of intense solidarity.

Loistehon säätö ja kompensointi

Kantaverkkoyhtiö Fingrid Oy on tarkastellut kantaverkosta otettua tai tuotettua loistehoa alueittain Fingridin määrittelemällä maantieteellisellä tavalla. Alue koostuu liittymispisteistä, jotka ovat yksittäisten verkkoyhtiöiden liittymispisteitä. Yhden alueen sisällä voi siis olla monia eri verkkoyhtiöiden liittymispisteitä. Vuodesta 2016 alkaen loistehon tarkastelu vaihtuu aluetarkastelusta liittymispistetarkasteluun. Liittymispistetarkasteluun siirtymisen myötä tulee verkkoyhtiöiden investoida erinäisiin kompensointiratkaisuihin, jotta yksittäisten liittymispisteiden loistehot pysyvät Fingridin asettaman loistehon tarkasteluikkunan sisällä. Työssä perehdytään erinäisiin kompensointiratkaisuihin ja niiden kytkentöihin sekä kytkentöjen vaikutuksiin olemassa olevaan sähköverkkoon. Lisäksi työssä käsitellään tuulivoimaloiden hyödyntämistä loistehon säädössä. Esimerkkitapauksessa tarkastellaan erästä Caruna Oy:n verkkoa ja pohditaan teknistä ja mahdollisimman taloudellista kompensointiratkaisua kyseiseen verkkoon. Työn lopputulos on, että maakaapeloinnin määrän kasvaessa loistehon kompensoinnin tarve kasvaa. Näin ollen Fingrid Oy:ltä tarvitaan selkeitä linjauksia moneen ongelmakohtaan, kuten tuotanto-kulutuspisteen loistehon tarkasteluun. Lisäksi Energiavirastolta tarvitaan kannusteita loistehon kompensointiin, sillä verkkoyhtiöiden liiketoiminta perustuu regulaatiomalliin ja kompensointilaitteiston yksikköhinnasto on hyvin suppea.

Purification of Hydrocarbon Waste Streams

Purification of hydrocarbon waste streams is needed to recycle valuable hydrocarbon products, reduce hazardous impacts on environment, and save energy. To obtain these goals, research must be focused on the search of effective and feasible purification and re-refining technologies. Hydrocarbon waste streams can contain both deliberately added additives to original product and during operation cycle accumulated undesired contaminants. Compounds may have degenerated or cross-reacted. Thus, the presence of unknown species cause additional challenges for the purification process. Adsorption process is most suitable to reduce impurities to very low concentrations. Main advantages are availability of selective commercial adsorbents and the regeneration option to recycle used separation material. Used hydrocarbon fraction was purified with various separation materials in the experimental part. First screening of suitable materials was done. In the second stage, temperature dependence and adsorption kinetics were studied. Finally, one fixed bed experiment was done with the most suitable material. Additionally, FTIR-measurements of hydrocarbon samples were carried out to develop a model to monitor the concentrations of three target impurities based on spectral data. Adsorption capacities of the tested separation materials were observed to be low to achieve high enough removal efficiencies for target impurities. Based on the obtained data, batch process would be more suitable than a fixed bed process and operation at high temperatures is favorable. Additional pretreatment step is recommended to improve removal efficiency. The FTIR-measurement was proven to be a reliable and fast analysis method for challenging hydrocarbon samples.

Optimized Fast-FISH with a-satellite probes: acceleration by microwave activation

It has been shown for several DNA probes that the recently introduced Fast-FISH (fluorescence in situ hybridization) technique is well suited for quantitative microscopy. For highly repetitive DNA probes the hybridization (renaturation) time and the number of subsequent washing steps were reduced considerably by omitting denaturing chemical agents (e.g., formamide). The appropriate hybridization temperature and time allow a clear discrimination between major and minor binding sites by quantitative fluorescence microscopy. The well-defined physical conditions for hybridization permit automatization of the procedure, e.g., by a programmable thermal cycler. Here, we present optimized conditions for a commercially available X-specific a-satellite probe. Highly fluorescent major binding sites were obtained for 74oC hybridization temperature and 60 min hybridization time. They were clearly discriminated from some low fluorescent minor binding sites on metaphase chromosomes as well as in interphase cell nuclei. On average, a total of 3.43 ± 1.59 binding sites were measured in metaphase spreads, and 2.69 ± 1.00 in interphase nuclei. Microwave activation for denaturation and hybridization was tested to accelerate the procedure. The slides with the target material and the hybridization buffer were placed in a standard microwave oven. After denaturation for 20 s at 900 W, hybridization was performed for 4 min at 90 W. The suitability of a microwave oven for Fast-FISH was confirmed by the application to a chromosome 1-specific a-satellite probe. In this case, denaturation was performed at 630 W for 60 s and hybridization at 90 W for 5 min. In all cases, the results were analyzed quantitatively and compared to the results obtained by Fast-FISH. The major binding sites were clearly discriminated by their brightness

Volatile cardioplegia: fast normothermic cardiac arrest induction and recovery with halothane in isolated rat hearts

To study the effect of halothane as a cardioplegic agent, ten Wistar rats were anesthetized by ether inhalation and their hearts were perfused in a Langendorff system with Krebs-Henseleit solution (36oC; 90 cm H2O pressure). After a 15-min period for stabilization the control values for heart rate, force (T), dT/dt and coronary flow were recorded and a halothane-enriched solution (same temperature and pressure) was perfused until cardiac arrest was obtained. The same Krebs-Henseleit solution was reperfused again and the parameters studied were recorded after 1, 3, 5, 10, 20 and 30 min. Cardiac arrest occurred in all hearts during the first two min of perfusion with halothane-bubbled solution. One minute after reperfusion without halothane, the following parameters reported in terms of control values were obtained: 90.5% of control heart rate (266.9 ± 43.4 to 231.5 ± 71.0 bpm), 20.2% of the force (1.83 ± 0.28 to 0.37 ± 0.25 g), 19.8% of dT/dt (46.0 ± 7.0 to 9.3 ± 6.0 g/s) and 90.8% of coronary flow (9.9 ± 1.5 to 9.4 ± 1.5 ml/min). After 3 min of perfusion they changed to 99.0% heart rate (261.0 ± 48.2), 98.9% force (1.81 ± 0.33), 98.6 dT/dt (45.0 ± 8.2) and 94.8% coronary flow (9.3 ± 1.4). At 5 min 100.8% (267.0 ± 40.6) heart rate, 105.0% (1.92 ± 0.29) force and 104.4% (48.2 ± 7.2) dT/dt were recorded and maintained without significant differences (P>0.01) until the end of the experiment. These data demonstrate that volatile cardioplegia with halothane is an effective technique for fast induction of and prompt recovery from normothermic cardiac arrest of the rat heart

Fast and slow voltage modulation of apical Cl- permeability in toad skin at high [K+]

The influence of voltage on the conductance of toad skin was studied to identify the time course of the activation/deactivation dynamics of voltage-dependent Cl- channels located in the apical membrane of mitochondrion-rich cells in this tissue. Positive apical voltage induced an important conductance inhibition which took a few seconds to fully develop and was instantaneously released by pulse inversion to negative voltage, indicating a short-duration memory of the inhibiting factors. Sinusoidal stimulation at 23.4 mM [Cl-] showed hysteresis in the current versus voltage curves, even at very low frequency, suggesting that the rate of voltage application was also relevant for the inhibition/releasing effect to develop. We conclude that the voltage modulation of apical Cl- permeability is essentially a fast process and the apparent slow components of activation/deactivation obtained in the whole skin are a consequence of a gradual voltage build-up across the apical membrane due to voltage sharing between apical and basolateral membranes

An optically coupled power stimulus isolation unit with high voltage and fast rise time output

Recent technological developments have created new devices that could improve and simplify the construction of stimulus isolators. HEXFET transistors can switch large currents and hundreds of volts in nanoseconds. The newer opto-isolators can give a pulse rise time of a few nanoseconds, with output compatible with MOSFET devices, in which delays are reduced to nanoseconds. Integrated DC/DC converters are now available. Using these new resources we developed a new electrical stimulus isolator circuit with selectable constant-current and constant-voltage modes, which are precise and easy to construct. The circuit works like a regulated power supply in both modes with output switched to zero or to free mode through an opto-isolator device. The isolator analyses showed good practical performance. The output to ground resistance was 1011 ohms and capacitance 35 picofarads. The rise time and fall time were identical (5 µs) and constant. The selectable voltage or current output mode made it very convenient to use. The current mode, with higher output resistance values in low current ranges, permits intracellular stimulation even with tip resistances close to 100 megaohms. The high compliance of 200 V guarantees the value of the current stimulus. The very low output resistance in the voltage mode made the device highly suitable for extracellular stimulation with low impedance electrodes. Most importantly, these characteristics were achieved with a circuit that was easy to build and modify and assembled with components available in Brazil.

Catalytic direct synthesis of hydrogen peroxide in a novel microstructured reactor

The direct synthesis from hydrogen and oxygen is a green alternative for production of hydrogen peroxide. However, this process suffers from two challenges. Firstly, mixtures of hydrogen and oxygen are explosive over a wide range of concentrations (4-94% H2 in O2). Secondly, the catalytic reaction of hydrogen and oxygen involves several reaction pathways, many of them resulting in water production and therfore decreasing selectivity. The present work deals with these two challenges. The safety problem was dealed by employing a novel microstructured reactor. Selectivity of the reaction was highly improved by development a set of new catalysts. The final goal was to develop an effective and safe continuous process for direct synthesis of hydrogen peroxide from H2 and O2. Activated carbon cloth and Sibunit were examined as the catalysts’ supports. Palladium and gold monometallic and palladium-gold bimetallic catalysts were thoroughly investigated by numerous kinetic experiments performed in a tailored batch reactor and several catalyst charachterization methods. A complete set of data for direct synthesis of H2O2 and its catalytic decomposition and hydrogenation was obtained. These data were used to assess factors influencing selectivity and activity of the catalysts in direct synthesis of H2O2 as well as its decomposition and hydrogenation. A novel microstructured reactor was developed based on hydrodynamics and mass transfer studies in prototype microstractural plates. The shape and the size of the structural elements in the microreactor plate were optimized in a way to get high gas-liquid interfacial area and gas-liquid mass transfer. Finally, empirical correlations for the volumetric mass transfer coefficient were derived. A bench-scale continuous process was developed by using the novel microstructral plate reactor. A series of kinetic experiments were performed to investigate the effects of the gas and the liquid feed rates and their ratio, the amount of the catalyst, the gas feed composition and pressure on the final rate of H2O2 production and selectivity.