Wirkung von Ernterückständen transgener Pflanzen auf die mikrobielle C- und N-Transformation in landwirtschaftlich genutzten Böden am Beispiel von Bt-Mais

In der vorliegenden Arbeit ging es um die Erarbeitung, Anwendung und Beurteilung von quantitativen Analysenverfahren / Methoden für ein Monitoring von durch Bt-Mais verursachbaren Umwelteffekten im Boden. Die Ausgangsthese besagte, dass sich transgene Maisstreu beim mikrobiellen Abbau anders verhält als konventionelle. Bezugnehmend auf die These wurden zwei Freilandversuche (Freilandmikrokosmenmethode nach Raubuch 1997 über 2 Jahre, Quantifizierung des Maisstreuabbaus mit Hilfe kleiner Bodensäulen über 1 Jahr) und zwei Inkubationsversuche im Labor (INK bei drei verschiedenen Temperaturen über 49 Tage und INK mit verschiedenen landwirtschaftlich genutzten Böden über 49 Tage mit jeweils kontinuierlicher Respirationsratenermittlung nach Isermeyer 1952) sowie Inhaltsstoffbestimmungen der Maisstreu durchgeführt. Für alle Untersuchungen wurde Streu der vier Maissorten Novelis (transgen, Monsanto 810), Nobilis (Isolinie von Novelis), Valmont (transgen, Bt 176, Fa. Syngenta) und Prelude (Isolinie von Valmont) eingesetzt. Nach Beendigung der Laborversuche sowie des Freilandversuches nach der Freilandmikrokosmenmethode wurden mikrobielle Messgrößen wie Adenylategehalt, Ergosterolgehalt, Cmik- und Nmik-Gehalt am Boden-Streu-Gemisch bestimmt. Der Einsatz der Isotopentechnik (Bestimmung von 13C/12C an gemahlenem Boden-Streu-Gemisch bzw. gefriergetrocknetem K2SO4 als Extrakt aus dem Boden-Streu-Gemisch) ermöglichte eine genaue Quantifizierung der abgebauten Maisstreu und brachte dadurch Aufschluss über das Abbauverhalten verschiedener Maissorten. Bezüglich der Ermittlung der mikrobiellen Messgrößen ergab sich für die transgene Sorte Novelis* stets eine durchschnittlich geringere pilzliche Biomasse. Langfristig ergaben sich bei der Kohlenstoff- und Stickstoffdynamik keine Trends hinsichtlich transgener bzw. konventioneller Maisstreu. Sowohl im Freilandversuch nach der Mikrokosmenmethode als auch in den Inkubationsversuchen trat das Phänomen der kurzzeitigen Respirationsratenerhöhung der Mikroorganismen nach Zugabe der transgenen Maissorten auf, welches nicht bei Zugabe der konventionellen Maisstreu auszumachen war. ______________________________

Überwachung der Vorspannkraft Externer Spannglieder mit Hilfe der Modalanalyse

Aufgrund ihrer Vorteile hinsichtlich Dauerhaftigkeit und Bauwerkssicherheit ist in Deutschland seit 1998 die externe Vorspannung in Hohlkastenbrücken zur Regelbauweise geworden. Durch Verwendung der austauschbaren externen Vorspannung verspricht man sich im Brückenbau weitere Verbesserungen der Robustheit und damit eine Verlängerung der Lebensdauer. Trotz des besseren Korrosionsschutzes im Vergleich zur internen Vorspannung mit Verbund sind Schäden nicht völlig auszuschließen. Um die Vorteile der externen Vorspannung zu nutzen, ist daher eine periodische Überwachung der Spanngliedkräfte, z. B. während der Hauptprüfung des Bauwerks, durchzuführen. Für die Überwachung der Spanngliedkräfte bei Schrägseilbrücken haben sich die Schwingungsmessmethoden als wirtschaftlich und leistungsfähig erwiesen. Für die Übertragung der Methode auf den Fall der externen Vorspannung, wo kürzere Schwingungslängen vorliegen, waren zusätzliche Untersuchungen hinsichtlich der effektiven Schwingungslänge, der Randbedingungen sowie der effektiven Biegesteifigkeit erforderlich. Im Rahmen der vorliegenden Arbeit wurde das Modellkorrekturverfahren, basierend auf der iterativen Anpassung eines F.E.-Modells an die identifizierten Eigenfrequenzen und Eigenformen des Spanngliedes, für die Bestimmung der Spanngliedkräfte verwendet. Dieses Verfahren ermöglicht die Berücksichtigung der Parameter (Schwingungslänge, Randbedingungen und effektive Biegesteifigkeit) bei der Identifikation der effektiven Spanngliedkräfte. Weiterhin ist eine Modellierung jeder beliebigen Spanngliedausbildung, z. B. bei unterschiedlichen Querschnitten in den Verankerungs- bzw. Umlenkbereichen, gewährleistet. Zur Anwendung bei der Ermittlung der Spanngliedkräfte wurde eine spezielle Methode, basierend auf den besonderen dynamischen Eigenschaften der Spannglieder, entwickelt, bei der die zuvor genannten Parameter innerhalb jedes Iterationsschrittes unabhängig korrigiert werden, was zur Robustheit des Identifikationsverfahrens beiträgt. Das entwickelte Verfahren ist in einem benutzerfreundlichen Programmsystem implementiert worden. Die erzielten Ergebnisse wurden mit dem allgemeinen Identifikationsprogramm UPDATE_g2 verglichen; dabei ist eine sehr gute Übereinstimmung festgestellt worden. Beim selbst entwickelten Verfahren wird die benötigte Rechenzeit auf ca. 30 % reduziert [100 sec à 30 sec]. Es bietet sich daher für die unmittelbare Auswertung vor Ort an. Die Parameteridentifikationsverfahren wurden an den Spanngliedern von insgesamt sechs Brücken (vier unterschiedliche Spannverfahren) angewendet. Die Anzahl der getesteten Spannglieder beträgt insgesamt 340. Die Abweichung zwischen den durch Schwingungs-messungen identifizierten und gemessenen (bei einer Brücke durch eine Abhebekontrolle) bzw. aufgebrachten Spanngliedkräften war kleiner als 3 %. Ferner wurden die Auswirkungen äußerer Einflüsse infolge Temperaturschwankungen und Verkehr bei den durchgeführten Messungen untersucht. Bei der praktischen Anwendung sind Besonderheiten aufgetreten, die durch die Verwendung des Modellkorrekturverfahrens weitgehend erfasst werden konnten. Zusammenfassend lässt sich sagen, dass die Verwendung dieses Verfahrens die Genauigkeit im Vergleich mit den bisherigen Schwingungsmessmethoden beachtlich erhöht. Ferner wird eine Erweiterung des Anwendungsbereiches auch auf Spezialfälle (z. B. bei einem unplanmäßigen Anliegen) gewährleistet.

Variación en la resistencia al flujo de los tubos endotraqueales pediátricos modificando su longitud

Introducción: Se conocen los beneficios del uso de los tubos endotraqueales con neumotaponador, aunque dicha práctica tiene un impacto sobre el trabajo respiratorio durante el acto anestésico sin embargo se propone estudiar las consecuencias físicas de la variación en la longitud de los tubos para compensar dicha perdida de flujo, con base en la ley de Hagen-Poiseuille. Metodología: Se realizó un estudio experimental in vitro, en el cual se realizaron mediciones repetidas de flujo, variando la longitud y diámetro de diferentes tubos endotraqueales pediátricos (desde calibre 3.5mm hasta 6.5mm), con longitudes de 20cm, 15 cm, 10 cm y manteniendo su longitud original. Se analizaron los datos con el fin de medir el impacto sobre el flujo. Resultados: A pesar que los resultados muestran diferencias estadísticamente significativas (p0,000), la variación en la longitud de los tubos endotraqueales pediátricos tiene mucho menor impacto sobre la variación en el flujo, que la modificación del diámetro. Discusión: Si bien la práctica de acortar la longitud de un tubo endotraqueal pediátrico puede ayudar a reducir el espacio muerto y la retención de CO2, el impacto que tiene sobre el flujo es poco. Cuando se trata de disminuir el trabajo respiratorio de un niño en ventilación espontánea durante el acto anestésico, se debe escoger de forma apropiada el calibre de tubo correspondiente para la edad.

Alteraciones en el material genético de pintores de carros expuestos a solventes orgánicos en una localidad de Bogotá

Los solventes orgánicos son sustancias químicas que por sus propiedades físico-químicas son fácilmente inhalados o absorbidos por la piel, pueden causar daños de diversa índole en la salud. En Colombia existen normas que contemplan las medidas de protección, sin embargo persiste la informalidad en el sector de pintores de autos, por lo cual los trabajadores expuestos, a largo plazo pueden ver afectada su salud. En este estudio se analizó la relación entre individuos expuestos laboralmente a los solventes orgánicos versus no expuestos con respecto a la longitud de sus telómeros y formación de fragilidades. Se emplearon muestras de sangre extraídas por venopunción, recolectada en dos tubos: uno con Heparina, destinado al cultivo de linfocitos, para obtener cromosomas metafásicos y evaluar en ellos la presencia de fragilidades; el otro tubo con EDTA, fue empleado para la extracción de ADN y se utilizó para obtener los valores de longitud telomérica mediante la técnica de PCR cuantitativa. Los análisis estadísticos se realizaron aplicando la prueba de rangos de Wilcoxon, en el caso de la presencia de fragilidades se analizó la razón No.Fragilidades/No.Metafases, aplicando el método de Wilcoxon se encontró que existe diferencia estadísticamente significativa entre expuestos y no expuestos (p = 0,036), en donde los expuestos presentan mayor frecuencia de fragilidades. Por otra parte el valor relativo de longitud telomérica del grupo de expuestos fue mayor que el observado en el grupo de no expuestos, esta diferencia fue estadísticamente significativa (Wilcoxon, p = 0.002).

The calibration and use of probe-test microphones

This paper examines the characteristics of the probe-tube microphone and its use in measuring sound pressure in the ear canal. Specifically the paper studies the free field and the coupler calibrations of several probe-tube microphones with tubes of different sizes and determines which characteristics of a probe tube are necessary for accurate measurements in both a free field and in a closed coupler.

Relative proportions of polycyclic aromatic hydrocarbons differ between accumulation bioassays and chemical methods to predict bioavailability

Chemical methods to predict the bioavailable fraction of organic contaminants are usually validated in the literature by comparison with established bioassays. A soil spiked with polycyclic aromatic hydrocarbons (PAHs) was aged over six months and subjected to butanol, cyclodextrin and tenax extractions as well as an exhaustive extraction to determine total PAH concentrations at several time points. Earthworm (Eisenia fetida) and rye grass root (Lolium multiflorum) accumulation bioassays were conducted in parallel. Butanol extractions gave the best relationship with earthworm accumulation (r2 ≤ 0.54, p ≤ 0.01); cyclodextrin, butanol and acetone–hexane extractions all gave good predictions of accumulation in rye grass roots (r2 ≤ 0.86, p ≤ 0.01). However, the profile of the PAHs extracted by the different chemical methods was significantly different (p < 0.01) to that accumulated in the organisms. Biota accumulated a higher proportion of the heavier 4-ringed PAHs. It is concluded that bioaccumulation is a complex process that cannot be predicted by measuring the bioavailable fraction alone. The ability of chemical methods to predict PAH accumulation in Eisenia fetida and Lolium multiflorum was hindered by the varied metabolic fate of the different PAHs within the organisms.

The solubility of gypsum in calcareous soils

Three gypsiferous-calcareous soils from the Al-Hassa Oasis in Saudi Arabia were examined to determine the conditions under which dissolution of gypsum could be hindered by the formation of coatings of calcite during leaching. Batch extraction with water of a sandy clay loam, a sandy clay and a sandy loam containing 40, 26 and 5% gypsum and 14, 12 and 13% calcite respectively was followed by chemical analysis of the extracts, SEM examination and XRD and EDX microprobe analysis. Extraction in closed centrifuge tubes for I h or 5 h showed that initially gypsum dissolved to give solutions near to equilibrium but then in the sandy clay loam, between one quarter and one third of the gypsum could not dissolve. In the sandy clay about one fifth of the gypsum could not dissolve with none remaining in the sandy loam. All the extracts were close to equilibrium with calcite. SEM and EDX examination showed that coatings of calcite had formed on the gypsum particles. The sandy clay loam was also extracted using an open system in which either air or air +1% CO2 was bubbled through the suspensions for 1 h with stirring. The gypsum dissolved more rapidly and all of the gypsum dissolved. Thus, where the rate of dissolution of gypsum was rapid, calcite did not manage to cover the gypsum surfaces probably because the surface was being continuously removed. Slower leaching conditions in the field are likely to be conducive to the formation of coatings and less dissolution of gypsum. (c) 2006 Elsevier B.V. All rights reserved.

Monitoring and modelling the three-dimensional flow of water under drip irrigation

The interpretation of soil water dynamics under drip irrigation systems is relevant for crop production as well as on water use and management. In this study a three-dimensional representation of the flow of water under drip irrigation is presented. The work includes analysis of the water balance at point scale as well as area-average, exploring uncertainties in water balance estimations depending on the number of locations sampled. The water flow was monitored by detailed profile water content measurements before irrigation, after irrigation and 24 h later with a dense array of soil moisture access tubes radially distributed around selected drippers. The objective was to develop a methodology that could be used on selected occasions to obtain 'snap shots' of the detailed three-dimensional patterns of soil moisture. Such patterns are likely to be very complex, as spatial variability will be induced for a number of reasons, such as strong horizontal gradients in soil moisture, variations between individual sources in the amount of water applied and spatial variability is soil hydraulic properties. Results are compared with a widely used numerical model, Hydrus-2D. The observed dynamic of the water content distribution is in good agreement with model simulations, although some discrepancies concerning the horizontal distribution of the irrigation bulb are noted due to soil heterogeneity. (c) 2006 Elsevier B.V. All rights reserved.

Characterization of mineral surfaces using FIB and TEM: a case study of naturally weathered alkali feldspars

Using a focused ion beam (FIB) instrument, electron-transparent samples (termed foils) have been cut from the naturally weathered surfaces of perthitic alkali feldspars recovered from soils overlying the Shap granite, northwest England. Characterization of these foils by transmission electron microscopy (TEM) has enabled determination of the crystallinity and chemical composition of near-surface regions of the feldspar and an assessment of the influence of intragranular microtextures on the microtopography of grain surfaces and development of etch pits. Damage accompanying implantation of the 30 kV Ga+ ions used for imaging and deposition of protective platinum prior to ion milling creates amorphous layers beneath outer grain surfaces, but can be overcome by coating grains with > 85 nm of gold before FIB work. The sidewalls of the foil and feldspar surrounding original voids are also partially amorphized during later stages of ion milling. No evidence was found for the presence of amorphous or crystalline weathering products or amorphous "leached layers" immediately beneath outer grain surfaces. The absence of a leached layer indicates that chemical weathering of feldspar in the Shap soils is stoichiometric, or if non-stoichiometric, either the layer is too thin to resolve by the TEM techniques used (i.e., <=similar to 2.5 nm) or an insufficient proportion of ions have been leached from near-surface regions so that feldspar crystallinity is maintained. No evidence was found for any difference in the mechanisms of weathering where a microbial filament rests on the feldspar surface. Sub-micrometer-sized steps on the grain surface have formed where subgrains and exsolution lamellae have influenced the propagation of fractures during physical weathering, whereas finer scale corrugations form due to compositional or strain-related differences in dissolution rates of albite platelets and enclosing tweed orthoclase. With progressive weathering, etch pits that initiated at the grain surface extend into grain interiors as etch tubes by exploiting preexisting networks of nanopores that formed during the igneous history of the grain. The combination of FIB and TEM techniques is an especially powerful way of exploring mechanisms of weathering within the "internal zone" beneath outer grain surfaces, but results must be interpreted with caution owing to the ease with which artifacts can be created by the high-energy ion and electron beams used in the preparation and characterization of the foils.

The expected imprint of flux rope geometry on suprathermal electrons in magnetic clouds

Magnetic clouds are a subset of interplanetary coronal mass ejections characterized by a smooth rotation in the magnetic field direction, which is interpreted as a signature of a magnetic flux rope. Suprathermal electron observations indicate that one or both ends of a magnetic cloud typically remain connected to the Sun as it moves out through the heliosphere. With distance from the axis of the flux rope, out toward its edge, the magnetic field winds more tightly about the axis and electrons must traverse longer magnetic field lines to reach the same heliocentric distance. This increased time of flight allows greater pitch-angle scattering to occur, meaning suprathermal electron pitch-angle distributions should be systematically broader at the edges of the flux rope than at the axis. We model this effect with an analytical magnetic flux rope model and a numerical scheme for suprathermal electron pitch-angle scattering and find that the signature of a magnetic flux rope should be observable with the typical pitch-angle resolution of suprathermal electron data provided ACE's SWEPAM instrument. Evidence of this signature in the observations, however, is weak, possibly because reconnection of magnetic fields within the flux rope acts to intermix flux tubes.

Unilateral incompatibility in Capsicum (Solanaceae): Occurrence and taxonomic distribution

Background and aims Unilateral incompatibility (UI) occurs when pollinations between species are successful in one direction but not in the other. Self-incompatible (SI) species frequently show UI with genetically related, self-compatible (SC) species, as pollen of SI species is compatible on the SC pistil, but not vice versa. Many examples of unilateral incompatibility, and all those which have been studied most intensively, are found in the Solanaceae, particularly Lycopersicon, Solanum, Nicotiana and Petunia. The genus Capsicum is evolutionarily somewhat distant from Lycopersicon and Solanum and even further removed from Nicotiana and Petunia. Unilateral incompatibility has also been reported in Capsicum; however, this is the first comprehensive study of crosses between all readily available species in the genus. Methods All readily available (wild and domesticated) species in the genus are used as plant material, including the three genera from the Capsicum pubescens complex plus eight other species. Pollinations were made on pot-grown plants in a glasshouse. The number of pistils pollinated per cross varied (from five to 40 pistils per plant), depending on the numbers of flowers available. Pistils were collected 24 h after pollination and fixed for 3-24 h. After staining, pistils were mounted in a drop of stain, squashed gently under a cover slip and examined microscopically under ultra-violet light for pollen tube growth. Key results Unilateral incompatibility is confirmed in the C. pubescens complex. Its direction conforms to that predominant in the Solanaceae and other families, i.e. pistils of self-incompatible species, or self-compatible taxa closely related to self-incompatible species, inhibit pollen tubes of self-compatible species. Conclusions Unilateral incompatibility in Capsicum does not seem to have arisen to prevent introgression of self-compatibility into self-incompatible taxa, but as a by-product of divergence of the C. pubescens complex from the remainder of the genus. (C) 2004 Annals of Botany Company.

Measuring bee diversity in different European habitats and biogeographical regions

Bee pollinators are currently recorded with many different sampling methods. However, the relative performances of these methods have not been systematically evaluated and compared. In response to the strong need to record ongoing shifts in pollinator diversity and abundance, global and regional pollinator initiatives must adopt standardized sampling protocols when developing large-scale and long-term monitoring schemes. We systematically evaluated the performance of six sampling methods (observation plots, pan traps, standardized and variable transect walks, trap nests with reed internodes or paper tubes) that are commonly used across a wide range of geographical regions in Europe and in two habitat types (agricultural and seminatural). We focused on bees since they represent the most important pollinator group worldwide. Several characteristics of the methods were considered in order to evaluate their performance in assessing bee diversity: sample coverage, observed species richness, species richness estimators, collector biases (identified by subunit-based rarefaction curves), species composition of the samples, and the indication of overall bee species richness (estimated from combined total samples). The most efficient method in all geographical regions, in both the agricultural and seminatural habitats, was the pan trap method. It had the highest sample coverage, collected the highest number of species, showed negligible collector bias, detected similar species as the transect methods, and was the best indicator of overall bee species richness. The transect methods were also relatively efficient, but they had a significant collector bias. The observation plots showed poor performance. As trap nests are restricted to cavity-nesting bee species, they had a naturally low sample coverage. However, both trap nest types detected additional species that were not recorded by any of the other methods. For large-scale and long-term monitoring schemes with surveyors with different experience levels, we recommend pan traps as the most efficient, unbiased, and cost-effective method for sampling bee diversity. Trap nests with reed internodes could be used as a complementary sampling method to maximize the numbers of collected species. Transect walks are the principal method for detailed studies focusing on plant-pollinator associations. Moreover, they can be used in monitoring schemes after training the surveyors to standardize their collection skills.

Diversity and systematics of the Malacosporea (Myxozoa)

Myxozoans belonging to the recently described class Malacosporea parasitize freshwater bryozoans during at least part of their life cycle. There are at present only two species described in this class: Buddenbrockia plumatellae and Tetracapsuloides bryosalmonae. The former can exist as vermiform and sac-like stages in bryozoan hosts. The latter, in addition to forming sac-like stages in bryozoans, is the causative agent of salmonid proliferative kidney disease (PKD). We undertook molecular and ultrastructural investigations of new malacosporean material to further resolve malacosporean diversity and systematics. Phylogenetic analyses of 18S rDNA sequences provided evidence for two new putative species belonging to the genus Buddenbrockia, revealing a two-fold increase in the diversity of malacosporeans known to date. One new malacosporean is a vermiform parasite infecting the bryozoan Fredericella sultana and the other occurs as sac-like stages in the rare bryozoan, Lophopus crystallinus. Both bryozoans represent new hosts for the genus Buddenbrockia. Our results have established that the malacosporean which infected F. sultana was not a vermiform stage of T. bryosalmonae, although it was collected from a site endemic for PKD. Ultrastructural investigation of new material of B. plumatellae revealed the presence of numerous external tubes associated with developing polar capsules, confirming that the absence of external tubes should no longer be considered as a character of the class Malacosporea.

Volatile flavour profile of goat meat extracted by three widely used techniques

Three procedures for the isolation of volatiles from grilled goat meat were compared: dynamic headspace entrainment on Tenax TA, simultaneous steam distillation-extraction, and solid-phase microextraction. Headspace entrainment on Tenax TA extracted the highest number of Maillard-derived volatile compounds. Two hundred and three volatile components were identified: 159 are reported for the first time in goat meat. Most of the volatiles detected (155) were lipid oxidation products, such as hydrocarbons, aldehydes, alcohols, ketones, carboxylic acids and esters. Forty-eight Maillard-derived compounds were identified. comprising pyrazines, pyrroles, thiophenes, furanthiol derivatives, alkyl and alicyclic sulphides, pyridines, and thiazoles. Some reported character impact compounds of cooked meat, e.g., 12-methyltridecanal, (EE)-2,4-decadienal, methional, and dimethyl trisulphide were identified in the volatile profile of goat meat, together with a series of C-2 to C-5 alkylformylcyclopentenes, which have been reported in cooked chicken, pork, beef and lamb, as being important for the characteristic flavour impression of different animal species. (C) 2009 Published by Elsevier Ltd.

Cavity-enhanced absorption: detection of nitrogen dioxide and iodine monoxide using a violet laser diode

We present an application of cavity-enhanced absorption spectroscopy with an off-axis alignment of the cavity formed by two spherical mirrors and with time integration of the cavity-output intensity for detection of nitrogen dioxide (NO2) and iodine monoxide (IO) radicals using a violet laser diode at lambda = 404.278 nm. A noise-equivalent (1sigma = root-mean-square variation of the signal) fractional absorption for one optical pass of 4.5x10(-8) was demonstrated with a mirror reflectivity of similar to0.99925, a cavity length of 0.22 m and a lock-in-amplifier time constant of 3 s. Noise-equivalent detection sensitivities towards nitrogen dioxide of 1.8x10(10) molecule cm(-3) and towards the IO radical of 3.3x10(9) molecule cm(-3) were achieved in flow tubes with an inner diameter of 4 cm for a lock-in-amplifier time constant of 3 s. Alkyl peroxy radicals were detected using chemical titration with excess nitric oxide (RO2 + NO --> RO + NO2). Measurement of oxygen-atom concentrations was accomplished by determining the depletion of NO2 in the reaction NO2 + O --> NO + O-2. Noise-equivalent concentrations of alkyl peroxy radicals and oxygen atoms were 3x10(10) molecule cm(-3) in the discharge-flow-tube experiments.