基于天际线识别的无人机实时姿态角估计

以无人机天际线识别为背景,提出了一种准确、实时的天际线识别算法,并由此估计姿态角。在结合实际情况的基础上,对天际线建立能量泛函模型,利用变分原理推出相应偏微分方程。在实际应用中出于对实时性的考虑,引入直线约束对该模型进行简化,然后利用由粗到精的思想识别天际线。首先,对图像预处理并垂直剖分,然后利用简化的水平直线模型对天际线进行粗识别,通过拟合获得天际线粗识别结果,最后在基于梯度和区域混合开曲线模型约束下精确识别天际线,并由此估计无人机滚动和俯仰姿态角。实验结果表明,该算法对天际线识别具有较好的鲁棒性、准确性和实时性。

柴达木盆地地震勘探关键技术研究

The rugged surface topography determined the seismic data acquisition construction conditions and the seismic wave explosive and receiver quality in Qaidam Basin. This dissertation systematically researched the seismic acquisition, imaging process and the attribute analysis techniques of complicated oil and gas reservoir. The main research achievements and cognitions are as follows: 1. Through the stimulation effects research and analysis from the aspect of lithologic water-containing differences, it’s specific that stable hydrous sand layer can effectively enhance the stimulation effects combined with the corresponding field tests. The seismic data S/N ratio has been improved due to the combination explosive stimulation. Through the fold number and maximum offset analyses of target horizon, the complicated geometry has been optimized and the S/N ratio of seismic data has been improved, which made an important basis for improvement of 3D seismic data. 2. It has been proved that the first arrival refraction static correction method under the model constraint of fine surface survey is suitable to the Qaidam Basin of western areas by the real seismic data processing. Although the refraction horizon of near surface has some changes in a certain extent, it’s steady basically. The refraction horizon can be continuously traced in sections, so it’s qualified for the refraction static correction method on the whole. 3. The research is based on the curved-ray pre-stack time migration techniques of rough topography, and improved the imaging precision of complex areas. This techniques adopted the constant and variable velocity scanning mode and enhanced the velocity analysis precision. The 3D pre-stack time migration techniques reasonably solved the imaging and velocity multiple solutions problems of steep-dip faults and the intersections of horizontal layers. What’s more, fine velocity analysis and mute are very important to enhance the imaging precision of the seismic data in complicated Wunan areas. 4. The 3D seismic data edge-preserving processing methods have been realized due to the image process techniques. Because this method uses the large range filter, it can attenuate the noise maximally. The faults, break points, lithologic pinchout points and lithologic body of small scale such as river will not be influenced by blur because of the edge-preserving characterization of the method which is really an effective assistant technique of low S/N ratio seismic data attribute analysis. 5. The use of spectral decomposition technique can effectively identify the reservoirs. The special geology body which will not be identified (or without obvious characters) in the seismic profile may be found through the details changes of different frequencies in the amplitude profiles.

陆地三分量三维地震勘探技术研究与应用

With the development of oil and gas field exploration, it becomes harder to search new reserves. So a higher demand of seismic exploration comes up. Now 3C3D seismic exploration technology has been applied in petroleum exploration domains abroad. Comparing with the traditional P-wave exploration, the seismic attributes information which provided by 3C3D seismic exploration will increase quickly. And it can derive various combined parameters. The precision of information about lithology, porosity, fracture, oil-bearing properties, etc which estimated by above parameters was higher than that of pure P-wave exploration. These advantages mentioned above lead to fast development of 3C3D seismic technology recently. Therefore, how to apply the technology in petroleum exploration field in China, how to obtain high quality seismic data, and how to process and interpret real data, become frontier topics in geophysical field nowadays, which have important practical significance in research and application. In this paper, according to the propagation properties of P-wave and converted wave, a study of 3C3D acquisition parameters design method was completed. Main parameters included: trace interval, shot interval, maximum offset, bin size, the interval of receiving lines, the interval of shooting lines, migration aperture, maximum cross line distance, etc. Their determination principle was given. The type of 3C3D seismic exploration geometry was studied. By calculating bin attributes and analyzing parameters of geometry, some useful conclusions were drawn. With the method in this paper, real geometries for continental lithology stratum gas reservoir and fractured gas reservoir were studied and determined. In the static method of multi-wave, the near surface P-wave, S-wave parameter investigation method has been advanced, and this method has been applied for the patent successfully; the near surface P-wave, S-wave parameter investigation method and the converted refraction wave first arrival static techniques have been integrally used to improve the effectiveness of converted wave static. In the aspect of converted wave procession, the rotation of horizontal component data, the calculation of converted wave common conversion bin, the residual static of converted wave, the velocity analysis of the common conversion point (CCP), the Kirchhoff pre-stack time migration of converted wave techniques have been applied for setting up the various 3C3D seismic data processing flows based on different geologic targets, and the high quality P-wave, converted-wave profiles have been acquired in the actual data processing. In the aspect of P-wave and converted-wave comprehensive interpretation, the thoughts and methods of using zero-offset S-wave VSP data to calibrate horizon have been proposed; the method of using P-wave and S-wave amplitude ratio to predict the areas of oil and gas enrichment has been studied; the method of inversion using P-wave combined with S-wave has been studied; the various P-wave, S-wave parameters(velocity ratio, amplitude ratio, poisson ratio) have been used to predict the depth, physical properties, gas-bearing properties of reservoirs; the method of predicting the continental stratum lithology gas reservoir has been built. The above techniques have all been used in various 3D3C seismic exploration projects in China, and the better effects have been gotten. By using these techniques, the 3C3D seismic exploration level has been improved.

渤海湾盆地前第三系构造演化与煤成气成藏研究

The disequilibrium between supply and demand the east part of North China accelerated natural gas exploration in Bohai bay basin. Exploration practice showed that coal-derived gas is important resource. In searching of big to middle scaled coal derived gas field, and realize successive gas supply, the paper carried out integrated study on structural evolution of Pre-Tertiary and evaluation of reservoir forming condition of coal-derived gas. Study work of the paper was based on the following condition: available achievement in this field at present, good understanding of multiphase of tectonic movement. Study work was focused on geological evolution, source rock evaluation and dissection key factors controlling reservoir forming. Based on analysis of seismic data, drilling data, tectonic style of Pre-Tertiary was subdivided, with different tectonic style representing different tectonic process. By means of state of the art, such as analysis of balanced cross section, and erosion restoration, the paper reestablished tectonic history and analyzed basin property during different tectonic phase. Dynamic mechanism for tectonic movement and influence of tectonic evolution on tectonic style were discussed. Study made it clear that tectonic movement is intensive since Mesozoic including 2 phase of compressional movement (at the end of Indo-China movement, and Yanshan movement), 2 phase of extensional movement (middle Yanshan movement, and Himalayan movement), 2 phase of strike slip movement, as well as 2 phase of reversal movement (early Yanshan movement, and early Himalayan movement). As a result, three tectonic provinces with different remnant of strata and different tectonic style took shape. Based on afore mentioned study, the paper pointed out that evolution of Bohai bay basin experienced the following steps: basin of rift valley type (Pt2+3)-craton basin at passive continental margin (∈1－2)-craton basin at active continental margin (∈3- O)-convergent craton basin (C-T1+2)-intracontinental basin (J＋K). Superposition of basins in different stage was discussed. Aimed at tectonic feature of multiple phases, the paper put forward concept model of superposition of tectonic unit, and analyzed its significance on reservoir forming. On basis of the difference among 3 tectonic movements in Mesozoic and Cenozoic, superposition of tectonic unit was classified into the following 3 categories and 6 types: continuous subsidence type (I), subsidence in Mesozoic and uplift for erosion in Cenozoic (II1), repeated subsidence and uplift in Mesozoic and subsidence in Cenozoic (II2), repeated subsidence and uplift in Mesozoic and uplift for erosion in Cenozoic (II3), uplift for erosion in Mesozoic and subsidence in Cenozoic (II4), and continuous uplift (III). Take the organic facies analysis as link, the paper established relationship between sedimentary environment and organic facies, as well as organic facies and organic matter abundance. Combined information of sedimentary environment and logging data, the paper estimated distribution of organic matter abundance. Combined with simulation of secondary hydrocarbon generation, dynamic mechanism of hydrocarbon generation, and thermal history, the paper made static and dynamic evaluation of effective source rock, i.e. Taiyuan formation and Shanxi formation. It is also pointed out that superposition of tectonic unit of type II2, type II4, and type I were the most favorable hydrocarbon generation units. Based on dissection of typical primary coal-derived gas reservoir, including reservoir forming condition and reservoir forming process, the paper pointed out key factors controlling reservoir forming for Carboniferous and Permian System: a. remnant thickness and source rock property were precondition; b. secondary hydrocarbon generation during Himalayan period was key factor; c. tectonic evolution history controlling thermal evolution of source rock was main factor that determine reservoir forming; d. inherited positive structural unit was favorable accumulation direction; e. fault activity and regional caprock determined hydrocarbon accumulation horizon. In the end, the paper established reservoir forming model for different superposition of tectonic units, and pointed out promising exploration belts with 11 of the first class, 5 of the second class and 6 of the third class.

煤系地层三维三分量地震数据解释方法研究

Conventional 3D seismic exploration cannot meet the demand of high yield and high efficiency safe production in coal mine any more. Now it is urgent to improve the discovery degree of coal mine geological structures for coal production in China. Based on 3D3C seismic exploration data, multi-component seismic information is fully excavated. First systematic research on 3D3C seismic data interpretation of coal measure strata is carried out. Firstly, by analyzing the coal measure strata, the seismic-geologic model of coal measure strata is built. Shear wave logging is built by using regression analysis. Horizon calibration methods of PP-wave and PS-wave are studied and the multi-wave data are used together to interpret small faults. Using main amplitude analysis technology, small faults which cannot be found from PP-wave sections can be interpreted from the low frequency PS-wave sections. Thus, the purpose to applying PS-wave data to fine structure assistant interpretation is achieved. Secondly, PP- and PS-wave post-stack well constrained inversion methods of coal measure strata are studied. Joint PP- and PS-wave post-stack inversion flow is established. More attribute parameters, which are applied in fine lithology interpretation of coal measure strata, are obtained from combinations of the inversion results. Exploring the relation between rock with negative Poisson’s ratio and anisotropy, fracture development in coal seam are predicted. Petrophysical features of coal measure strata are studied, and the relations between elastic parameters and lithology, fluid and physical properties are established. Inversions of the physical parameters such as porosity, permeability and water saturation, which reflect lithology and fluid property, are obtained. Finally, the approaches of shear wave splitting and Thomsen parameters inversion, which provide new ideas for seismic anisotropy interpretation of coal measure strata, are studied to predict fracture development. The results of practical application indicate that the methods in this paper have good feasibility and applicability. They have positive significance for high yield and high efficiency safe production in coal mine.

鄂尔多斯盆地子洲气田二叠系山西组储层特征与天然气富集规律研究

In this thesis, detailed studies on the sedimentology and petrophysical properties of reservoir rocks in the Shan#2 Member of Shanxi Formation, Zizhou gas field of Ordos Basin, are carried out, based on outcrop description, core description, wireline log interpretation and analysis of petrophysical properties. In the context of stratigraphic division scheme of the Upper Paleozoic in Ordos Basin, the Shan#2 Member is further divided into three subintervals: the Shan#23, Shan#22 and Shan#21, based on the marker beds，depositional cycles, wireline log patterns. Subaqueous deltaic-front distributary channels, distributed from the south to north, is identified，which is the main reservoir sand bodies for gases of Shan#2 Member at Zizhou gas field. Quartzose and lithic-quartzose sandstones, commonly with a high volume of cement, but a low volume of matrix, are the major reservoir rocks in the studied area. All sandstones have been evolved into the late diagenetic stage (referred to as diagenetic stage B) during the burial, experiencing compaction, cementation, replacement and dissolution, in which the compaction and cementation could have reduced the porosity, while dissolution could have improved the petrophysical properties. The pore types in the reservoirs are dominated by intergranular-solutional, intergranular-intercrystal and intercrystal-solutional porosity. According to the parameters and capillary pressure curves of test samples, five types of pore texture (I-V) are differentiated, in which types II and III pore textures displayed by low threshold pressure-wide pore throat and moderate threshold pressure-moderately wide pore throat, exist widespread. Sandstone reservoirs in the studied area are characterized by exceptionally low porosity and permeability, in which the petrophysical properties of those in Shan#23 horizon are relatively better. The petrophysical property of reservoirs was influenced both by the sedimentation and diagenesis. In general, the coarse quartzose sandstones deposited in subaqueous distributary channels show the best petrophysical property, which tends to be worse as the grain size decreases and lithic amount increases. Three types of gas reservoirs in Shan#23 horizon are classified according to petrophysical properties (porosity and permeability), which could have been influenced by the initial depositional facies, diagenesis and tectonics. On the basis of the study on the geological conditions of reservoirs in the area, it is concluded that sedimetary facies, diagenesis and tectonic actions can provide an important foundation for gas pool formation, which can also control the accumulation and distribution of gas reservoirs.

叠前地震多角度三参数同步反演方法

Pre-stack seismic inversion has become the emphasis and hotspot owing to the exploration & exploitation of oil field and the development of seismic technology. Pre-stack seismic inversion has the strongpoint of making the most of amplitude versus offset compared with the post-stack method. In this dissertation, the three parameters were discussed from multi-angle reflectance of P-wave data based on Zoeppritz’s and Aki & Richard’s equation, include P-wave velocity, S-wave velocity, and density. The three parameters are inversed synchronously from the pre-stack multi-angle P-wave data, based on rockphysics model and aimed at the least remnant difference between model simulation and practical data. In order to improve the stability of inversion and resolution to thin bed, several techniques were employed, such as the wavelet transform with multi-scale function, adding the Bayesian soft constraint and hard constraints (the horizon, structure and so on) to the inversion process. Being the result, the uncertainty of the resolution is reduced, the reliability and precision are improved, the significance of parameters becomes clearer. Meeting to the fundamental requirement of pre-stack inversion, some research in rockphysics are carried out which covered the simulation and inversion of S-wave velocity, the influence of pore fluids to geophysical parameters, and the slecting and analyzing of sensitive parameters. The difference between elastic wave equation modeling and Zoeppritz equation method is also compared. A series of key techniques of pre-stack seismic inversion and description were developed, such as attributes optimization, fluid factors, etc. All the techniques mentioned above are assembled to form a technique sets and process of synchronous pre-stack seismic inversion method of the three parameters based on rock physics and model simulation. The new method and technology were applied in many areas with various reservoirs, obtained both geological and economic significance, which proved to be valid and rational. This study will promote the pre-stack inversion technology and it’s application in hidden reservoirs exploration, face good prospects for development and application.

湘西地区上震旦统上部－下寒武统底部黑色岩系沉积学及地球化学

Widespread black chert-shales occur in the Ediacaran-Cambrian(E-C) boundary successions along the flank of Yangtze Platform, South China, remarkable changes in sedimentology, geochemistry and biology were recorded. Although extensive studies were carried out upon this boundary succession, the origin of black chert-shales still remain controversial. This paper focuses on the E-C black chert-shales in western Hunan, South China, upon which detailed depositional and geochemical changes are documented, accordingly a depositional model for black chert-shales is proposed. Stratigraphic anatomy across the depositional strike demonstrates that the shallow-water Dengying dolostone along the platform margin sharply pass basinward into the Liuchapo chert successions, which indicate syndepositional extensional faulting at depth could have occurred along the platform margin. The deep-water Niutitang phosphorite-rich black shales are either underlain by the Dengying dolostones on the platform margin toward platform interior or directly by the Liuchaopo chert successions farther basinwards. By detailed investigation, silica chimneys are firsly identified approximately in the chert along platform margin; two types of silica chimneys, including mounded and splayed/funnelized chert(generally brecciated) bodies are further sorted out. The mounded chert are exitbited by domed or hummocky surfaces on the top and irregular spongy to digitiform internal fabrics; within the silica mounds, abundant original vesicles/voids and/or channels were mostly plugged by initial chalcedony, quartze crystals with minor dolomite and bladed barite crystals. Splayed/funnelized brecciated chert “intrusion” cross-cut the uppermost dolostones capping to the horizon underneath, and are directly overlain by the Niutitang phosphorite-rich black shales. Their similarities to the silica chimneys reported from the oceanic spreading centres suggest a similar origin responsible for these unique silica bodies which is also supported by the microthermonmetric data and element geochemistry. High P, Ba, Fe contents and positive correlation between Fe and TOC concentrations in the Niutitang black shales indicate a high palaeo-productivity in the Early Cambrian ocean. The low Th/U and the high V/Cr, V/Sc, V/(V+Ni) ratios in the black shales suggest an anoxic water condition during this interval. Furthermore, Positive Eu anomalies and high Ba contents in the sediments also imply a hydrothermal influence on the formation of Niutitang black shales. To better constrain the placement of deep-water successions straddling the E-C boundary and the timing of hydrothermal silica chimneys, sensitive high-resoluton ion microprobe(SHRIMP) U-Pb dating of zircon grains from tuffs within the chert succession of Liuchapo Formation at Ganziping was conducted and yields a weighted-mean 206Pb/238Pb age at 536.6±5.5Ma, younger than E-C boundary age(542.0±0.3Ma). This age combined with carbon isotopic data is then proposed to correspond to the U-Pb age of zircons(538.2±1.5Ma) from the Zhongyicun member of Meishucun Formation at Meishucun in eastern Yunna, thus, the E-C boundary in Gazngziping was placed between the Dengying formations and Liuchapo formatioms. therefore, the silica chimneys took place at the beginning of the Cambrian period. The temporal coincidence of silica chimneys and negative excursions of δ13C and δ34Spy pairs suggest hydrothermal activities were likely responsible for the isotopic changes. Under such a circumstance, vast amounts of greenhouse gases(CO2, CH4, H2S), with highly 13C-depleted carbon and 34S-depleted sulfur would be released into the ocean and atmosphere. A positive shift in δ34Scas and Δ34S values from the late Ediacaran to the Early Cambrian could be a reflection of enhanced bacterial sulfate reduction(BSR), strengthened by the intensified oceanic anoxia stimulated by hydrothermal activities. Based on the analyses of sedimentology and geochemistry, a model- “oceanic anoxia induced by hydrothermal–volcanic activies” was proposed to responsible for the formation of black chert-shales during this E-C transition. Under this case, hydrothermal-volcanic activies could release large large amount of greenhouse into atmosphere and metal micronutrients into the ocean, which may lead to global warming, stratified ocean, thereby a high palaeoproductivity; on the other hand, the massive releasing of reduced hydrothermal fluids with abundant H2S, could have in turn enhanced the ocean anoxia. All of these were favourable the for preservation of organic matter, and subsequent extensive deposition of black silica-shales.

沾化凹陷火成岩油气藏形成条件和分布规律研究

As a kind of special lithologic ones, Igneous rock oil and gas pool is more and more paid attention, and it has different forming condition and distribution from conventional ones, such as various terrane distribution types, serious reservoir anisotropy, complicated hydrocarbon-bearing, so there is not successful experience to follow for exploration and development of this complex subtle oil and gas pool at present. For an example of Igneous oil and gas pool of Luo151 area in Zhanhua seg, Eastern China, this article study the difficult problem, including petrologic nd lithofacies analysis, Origin, invasion age and times of Igneous rock, reservoir anisotropy, Geological Modeling, Igneous reservoir synthesis evaluation. forming condition and distribution are studied synthetically, and an integrated method to predict igneous rock oil and gas pool is formed, which is evaluated by using development data. The Igneous rock is mainly diabase construction in Luo151 area of Zhanhua Sag, and petrologic types include carbonaceous slate, hornfels, and diabases. Based on analyzing synthetically petrologic component, texture and construct, 4 lithofacies zones, such as carbonaceous slate subfacies, hornfels subfacies containing cordierite and grammite, border subfacies and central subfacies, are divided in the diabase and wall rock. By studying on isotopic chronology, terrane configuration and imaging logging data, the diabase intrusion in Zhanhua Sag is formed by tholeiite magma emplacing in Shahejie formation stratum on the rift tension background Lower Tertiary in North China. The diabase intrusion of Luo151 is composed possibly of three periods magma emplacement. There is serious anisotropy in the diabase reservoirs of Luo151 in Zhanhua Sag. Fracture is primary reservoir space, which dominated by tensile fracture in high obliquity, and the fracture zones are mainly developed round joint belt of igneous rock and wall rock and position of terrane thickness changing rapidly. The generation materials of the reservoirs in Luo151 igneous oil pools consist of Intergranular micropore hornfels, condensate blowhole-solution void diabase condensate edge, the edge and center of the condensate seam diabase, of which are divided into horizontal, vertical and reticulated cracks according fracture occurrence. Based on the above research, a conceptual model of igneous rock reservoir is generated, which is vertically divided into 4 belts and horizontally 3 areas. It is built for the first time that classification evaluation pattern of igneous rock reservoir in this area, and 3 key wells are evaluated. The diabase construction is divided into grammite hornfels micropore type and diabase porous-fracture type reservoirs. The heavy mudstone layers in Third Member of Shahejie formation (Es3) provide favorable hydrocarbon source rock and cap formation, diabase and hornfels belts serve as reservoirs, faults and microcracks in the wall rocks as type pathways for oil and gas migration. The time of diabase invasion was about in the later deposition period of Dongying Formation and the middle of that of Guantao Formation, the oil generated from oil source rock of Es3 in the period of the Minghuazhen formation and is earlier more than the period of diabase oil trap and porous space forming. Based on geological and seismic data, the horizon of igneous rocks is demarcated accurately by using VSP and synthetic seismogram, and the shape distribution and continuity of igneous rocks are determined by using cross-hole seismic technology. The reservoir capability is predicted by using logging constraining inversion and neural network technology. An integrated method to predict igneous rock oil and gas pool is formed. The study is appraised by using development data. The result show the reservoir conceptual model can guide the exploration and development of oil pool, and the integrated method yielded marked results in the production.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

东南极格罗夫山地区的土壤特征及其环境研究

The Grove Mountains, including 64 nunataks, is situated on an area about 3200km2 in the inland ice cap of east Antarctica in Princess Elizabeth land (72o20'-73°101S, 73°50'-75o40'E), between Zhongshan station and Dome A, about 450km away from Zhongshan station (69°22'S, 76°22'E). Many workers thought there was no pedogenesis in the areas because of the less precipitation and extreme lower temperature. However, during the austral summer in 1999-2000, the Chinaer 16 Antarctic expedition teams entered the inland East Antarctica and found three soil spots in the Southern Mount Harding, Grove Mountains, East Antarctica. It is the first case that soils are discovered in the inland in East Antarctica. Interestingly, the soils in this area show clay fraction migration, which is different from other cold desert soils. In addition, several moraine banks are discovered around the Mount Harding. The soil properties are discussed as below. Desert pavement commonly occurs on the three soil site surfaces, which is composed of pebbles and fragments formed slowly in typical desert zone. Many pebbles are subround and variegated. These pebbles are formed by abrasion caused by not only wind and wind selective transportation, but also salt weathering and thaw-freezing action on rocks. The wind blows the boulders and bedrocks with snow grains and small sands. This results in rock disintegration, paved on the soil surface, forming desert pavement, which protects the underground soil from wind-blow. The desert pavement is the typical feature in ice free zone in Antarctica. There developed desert varnish and ventifacts in this area. Rubification is a dominant process in cold desert Antarctic soils. In cold desert soils, rubification results in relatively high concentrations of Fed in soil profile. Stained depth increases progressively with time. The content of Fed is increasing up to surface in each profile. The reddish thin film is observed around the margin of mafic minerals such as biotite, hornblende, and magnetite in parent materials with the microscope analyzing on some soil profiles. So the Fed originates from the weathering of mafic minerals in soils. Accumulations of water-soluble salts, either as discrete horizons or dispersed within the soil, occur in the soil profiles, and the salt encrustations accumulate just beneath surface stones in this area. The results of X-ray diffraction analyses show that the crystalline salts consist of pentahydrite (MgSO4-5H2O), hexahydrite (MgSO4-6H2O), hurlbutite (CaBe2(PO4)2), bloedite (Na2Mg(S04)2-4H2O), et al., being mainly sulfate. The dominant cations in 1:5 soil-water extracts are Mg2+ and Na+, as well as Ca2+ and K+, while the dominant anion is SO42-, then NO3-, Cl- and HCO3-. There are white and yellowish sponge materials covered the stone underside surface, of which the main compounds are quartz (SiO2, 40.75%), rozenite (FeSOKkO, 37.39%), guyanaite (Cr2O3-1.5H2O, 9.30%), and starkeyite (MgSO4-4H2O, 12.56%). 4) The distribution of the clay fraction is related to the maximum content of moisture and salts. Clay fraction migration occurs in the soils, which is different from that of other cold desert soils. X-ray diffraction analyses show that the main clay minerals are illite, smectite, then illite-smectite, little kaolinite and veirniculite. Mica was changed to illite, even to vermiculite by hydration. Illite formed in the initial stage of weathering. The appearance of smectite suggests that it enriched in magnesium, but no strong eluviation, which belongs to cold and arid acid environment. 5) Three soil sites have different moisture. The effect moisture is in the form of little ice in site 1. There is no ice in site 2, and ice-cement horizon is 12 cm below the soil surface in site 3. Salt horizon is 5-10 cm up to the surface in Site 1 and Site 2, while about 26cm in site 3. The differentiation of the active layer and the permafrost are not distinct because of arid climate. The depth of active layer is about 10 cm in this area. Soils and Environment: On the basis of the characteristics of surface rocks, soil colors, horizon differentiation, salt in soils and soil depth, the soils age of the Grove Mountains is 0.5-3.5Ma. No remnants of glaciations are found on the soil sites of Mount Harding, which suggests that the Antarctic glaciations have not reached the soil sites since at least 0.5Ma, and the ice cap was not much higher than present, even during the Last Glacial Maximum. The average altitude of the contact line of level of blue ice and outcrop is 2050m, and the altitude of soil area is 2160m. The relative height deviation is about 110m, so the soils have developed and preserved until today. The parental material of the soils originated from alluvial sedimentary of baserocks nearby. Sporepollen were extracted from the soils, arbor pollen grains are dominant by Pinus and Betula, as well as a small amount Quercus, Juglans, Tilia and Artemisia etc. Judging from the shape and colour, the sporepollen group is likely attributed to Neogene or Pliocene in age. This indicates that there had been a warm period during the Neogene in the Grove Mountains, East Antarctica.

地球化学新方法在隐状矿床找矿预测中的应用研究

With the progress of prospecting, the need for the discovery of blind ore deposits become more and more urgent. To study and find out the method and technology for the discovery of blind and buried ores is now a priority task. New geochemical methods are key technology to discover blind ores. Information of mobile components related to blind ores were extracted using this new methods. These methods were tested and applied based on element' s mobile components migrating and enriched in geophysical-geochemical process. Several kinds of partial extraction techniques have tested based on element' s occurrence in hypergenic zone. Middle-large scale geochemical methods for exploration in forest and swamp have been tested. A serious of methods were tested and applied effetely about evaluation of regional geochemical anomaly, 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system instead of the normal net. 1. Element related with ores can be mobiled to migrate upwards and be absorpted by surface soil. These abnomal components can be concentrated by natural or artificial methods. These trace metalic ions partially exist in dissovlvable ion forms of active state, and partially have been absorbed by Fe-Mn oxide, soil and organic matter in the soil so that a series of reaction such as complex reaction have take place. Employing various partial extraction techniques, metallic ions related with the phase of the blind ores can be extracted, such as the technique of organic complex extraction, Fe-Mn oxide extraction and the extraction technique of metallic ions of various absorption phases. 2.1:200000 regional geochemical evaluation anomaly methods: Advantageous ore-forming areas were selected firstly. Center, concentration, morphological feature, belt of anomaly were choosed then. Geological and geochemical anomalies were combined. And geological and geochemical background information were restrained. Xilekuduke area in Fuyun sheet , Zhaheba area in Qiakuerte sheet, the west-north part in Ertai sheet and Hongshanzui anomaly in Daqiao sheet were selected as target areas, in Alertai, in the north of Xinjiang. in Xilekuduke area, 1:25000 soil geochemical methods sampling based on the net in dendritic water system was carried out. Cu anomaly and copper mineralization were determined in the center area. Au , Cu anomalies and high polarization anomaly were determined in the south part. Prospecting by primary halo and organic complex extraction were used to prognosis blind ore in widely rang outcrop of bedrock. 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system were used in transported overburden outside of mining area. Shallow seismic method and primary halo found a new blind orebody in mining area. A mineralization site was fou and outside of Puziwan gold mine, in the north of Shanxi province. Developing middle-large scale geochemical exploration method is a key technique based 1:200000 regional geochemical exploration. Some conditions were tested as Sampling density , distribution sites of sample, grain size of sample and occurrence of element for exploration. 1:50000 exploration method was advanced to sample clast sediment supplement clast sediment in valley. 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system was applied to sample residual material in A or C horizon. 1:2000 primary or soil halo methods used to check anomalies and determine mineralization. Daliang gold mineralization in the northern Moerdaoga was found appling these methods. Thermomagnetic method was tested in miniqi copper-polymetallic ore. Process methods such as grain size of sample, heated temperature, magnetic separating technique were tested. A suite of Thermomagnetic geochemical method was formed. This method was applied in Xiangshan Cu~Ni deposit which is cover by clast or Gobi in the eastern Xinjiang. Element's content and contrast of anomaly with Thermomagnetic geochemical method were higher than soil anomaly. Susceptibility after samples were heated could be as a assessment conference for anomaly. In some sectors thermo-magnetic Cu, Ni, Ti anomalious were found outside deposits area. There were strong anomal ies response up ore tested by several kind of partial extraction methods include Thermomagnetic, enzyme leach and other partial extractions in Kalatongke Cu-Ni deposit in hungriness area in the northern of Xinjiang. Element's anomalies of meobile were mainly in Fe-Mn oxide and salt. A Copper mineralization site in Xilekuduke anomaly area had been determined. A blind ore was foung by shallow seismic and geochemical method and a mineralization site was found outside this mining area in Puziwan gold deposit in shanxi province. A Gold mineralization site was found by 1:50000 geochemical exploration in Daliang, Inner Mongolia.

心算年老化的认知心理机制及功能磁共振成像研究

Mechanisms underlying cognitive psychology and cerebral physiological of mental arithmetic with increasing are were studied by using behavioral methods and functional magnetic resonance imaging (fMRI). I. Studies on mechanism underlying cognitive psychology of mental arithmetic with increasing age These studies were accomplished in 172 normal subjects ranging from 20 to 79 years of age with above 12 years of education (Mean = 1.51, SD = 1.5). Five mental arithmetic tasks, "1000-1", "1000-3", "1000-7", "1000-13", "1000-17", were designed with a serial calculation in which subjects sequentially subtracted the same prime number (1, 3, 7, 13, 17) from another number 1000. The variables studied were mental arithmetic, age, working memory, and sensory-motor speed, and four studies were conducted: (1) Aging process of mental arithmetic with different difficulties, (2) mechanism of aging of mental arithmetic processing. (3) effects of working memory and sensory-motor speed on aging process of mental arithmetic, (4) model of cognitive aging of mental arithmetic, with statistical methods such as MANOVA, hierarchical multiple regression, stepwise regression analysis, structural equation modelling (SEM). The results were indicated as following: Study 1: There was an obvious interaction between age and mental arithmetic, in which reaction time (RT) increased with advancing age and more difficult mental arithmetic, and mental arithmetic efficiency (the ratio of accuracy to RT) deceased with advancing age and more difficult mental arithmetic; Mental arithmetic efficiency with different difficulties decreased in power function: Study 2: There were two mediators (latent variables) in aging process of mental arithmetic, and age had an effect on mental arithmetic with different difficulties through the two mediators; Study 3: There were obvious interactions between age and working memory, working memory and mental arithmetic; Working memory and sensory-motor speed had effects on aging process of mental arithmetic, in which the effect of working memory on aging process of mental arithmetic was about 30-50%, and the effect of sensory-motor speed on aging process of mental arithmetic was above 35%. Study 4: Age, working memory, and sensory-motor speed had effects on two latent variables (factor 1 and factor 2), then had effects on mental arithmetic with different difficulties through factor 1 which was relative to memory component, and factor 2 which relative to speed component and had an effect on factor 1 significantly. II. Functional magnetic resonance imaging study on metal arithmetic with increasing age This study was accomplished in 14 normal right-handed subjects ranging from 20 to 29 (7 subjects) and 60 to 69 (7 subjects) years of age by using functional magnetic resonance imaging apparatus, a superconductive Signa Horizon 1.5T MRI system. Two mental arithmetic tasks, "1000-3" and "1000-17", were designed with a serial calculation in which subjects sequentially subtracted the same prime number (3 or 17) from another number 1000 silently, and controlling task, "1000-0", in which subjects continually rehearsed number 1000 silently, was regarded as baseline, based on current "baseline-task" OFF-ON subtraction pattern. Original data collected by fMRI apparatus, were analyzed off-line in SUN SPARC working station by using current STIMULATE software. The analytical steps were composed of within-subject analysis, in which brain activated images about mental arithmetic with two difficulties were obtained by using t-test, and between-subject analysis, in which features of brain activation about mental arithmetic with two difficulties, the relationship between left and right hemisphere during mental arithmetic, and age differences of brain activation in young and elderly adults were examined by using non-parameter Wilcoxon test. The results were as following:

Training needs analysis of healthcare library staff, undertaken for South Yorkshire Workforce Development Confederation

Urquhart, C., Durbin, J. & Spink, S. (2004). Training needs analysis of healthcare library staff, undertaken for South Yorkshire Workforce Development Confederation. Aberystwyth: Department of Information Studies, University of Wales Aberystwyth. Sponsorship: South Yorkshire WDC (NHS)

Prawda - istina w horyzoncie anthropos w myśli rosyjskiego renesansu religijno-filozoficznego

Wydział Nauk Społecznych: Instytut Filozofii