Power converters design and analysis for high power piezoelectric ultrasonic transducers

High power piezoelectric ultrasonic transducers have been widely exploited in a variety of applications. The critical behaviour of a piezoelectric device is encapsulated in its resonant frequencies because of its maximum transmission performance at these frequencies. Therefore power electronic converters should be tuned at those resonant frequencies to transfer electrical power to mechanical power efficiently. However, structural and environmental changes cause variations in the device resonant frequencies which can degrade the system performance. Hence, estimating the device resonant frequencies within the incorporated setup can significantly improve the system performance. This paper proposes an efficient resonant frequency estimation approach to maintain the performance of high power ultrasonic applications using the employed power converter. Experimental validations indicate the effectiveness of the proposed method.

The impact of auditor independence regulations on established and emerging firms.

Purpose – The purpose of this paper is to study whether auditor independence reforms introduced in 2004 led to an enhancement in earnings quality in the post-reform era. Design/methodology/approach – This study predicts that as the cost of compliance will vary based on a firm's existing corporate governance regime and the level of external scrutiny (monitoring) it faces, we compare the earnings quality of a sample of “established” (S&P/ASX 100) to a sample of “emerging” (S&P/ASX Small Ordinaries Index) firms. The paper examines the reporting behaviour of the two groups of listed entities, covering the regulatory change period 2003-2006. The paper uses regression modelling to test the associations between increased audit independence, earnings quality and corporate governance mechanisms over the pre- and post-regulatory period. Findings – The paper's results confirm that earnings quality for the established firms was enhanced in the post-reform period; while this was not the case for emerging firms. The evidence also suggests that corporate governance mechanisms of board independence and board financial skill are associated with higher earnings quality; while the higher the concentration of insider firm ownership is associated with lower earnings quality. Practical implications – This study provides policy makers with evidence as to changes in reporting behaviour following law reform aimed at strengthening auditor independence. Originality/value – The studies on earnings quality are informed by the US market practices. Australia provides a unique setting through its auditor independence reforms to examine the impact of reform choices. This study also investigates two specific subsets of the market: established firms and emerging firms.

Emerging genomic biomarkers in migraine

Migraine is a debilitating neurovascular condition classified as either migraine with aura or migraine without aura. A significant genetic basis has been implicated in migraine and has probed the role of neurotransmitters, hormones and vascular genes in this disorder. The aim of this review is to highlight the recent genetic discoveries contributing to our understanding of the complex pathogenesis of migraine. The current review will discuss the role of neurotransmitter-related genes in migraine, including the recently identified TRESK and variants of the KCNN3 gene, as well as outlining studies investigating hormone receptor genes, such as ESR1 and PGR, and vascular-related genes, including the MTHFR and NOTCH 3 genes.

Visual guidance for fixed-wing unmanned aerial vehicles using feature tracking : application to power line inspection

This thesis presents novel vision based control solutions that enable fixed-wing Unmanned Aerial Vehicles to perform tasks of inspection over infrastructure including power lines, pipe lines and roads. This is achieved through the development of techniques that combine visual servoing with alternate manoeuvres that assist the UAV in both following and observing the feature from a downward facing camera. Control designs are developed through techniques of Image Based Visual Servoing to utilise sideslip through Skid-to-Turn and Forward-Slip manoeuvres. This allows the UAV to simultaneously track and collect data over the length of infrastructure, including straight segments and the transition where these meet.

High frequency high power converters for industrial applications

The main contribution of this project was to investigate power electronics technology in designing and developing high frequency high power converters for industrial applications. Therefore, the research was conducted at two levels; first at system level which mainly encapsulated the circuit topology and control scheme and second at application level which involves with real-world applications. Pursuing these objectives, varied topologies have been developed and proposed within this research. The main aim was to resolving solid-state switches limited power rating and operating speed while increasing the system flexibility considering the application characteristics. The developed new power converter configurations were applied to pulsed power and high power ultrasound applications for experimental validation.

Two-stage power network reconfiguration strategy considering node importance and restored generation capacity

Network reconfiguration after complete blackout of a power system is an essential step for power system restoration. A new node importance evaluation method is presented based on the concept of regret, and maximisation of the average importance of a path is employed as the objective of finding the optimal restoration path. Then, a two-stage method is presented to optimise the network reconfiguration strategy. Specifically, the restoration sequence of generating units is first optimised so as to maximise the restored generation capacity, then the optimal restoration path is selected to restore the generating nodes concerned and the issues of selecting a serial or parallel restoration mode and the reconnecting failure of a transmission line are next considered. Both the restoration path selection and skeleton-network determination are implemented together in the proposed method, which overcomes the shortcoming of separate decision-making in the existing methods. Finally, the New England 10-unit 39-bus power system and the Guangzhou power system in South China are employed to demonstrate the basic features of the proposed method.

International acclaim : the role(s) of the international film festival in supporting emerging women’s cinema

International Film Festivals act as important sites for the exhibition of contemporary world cinema. Film festivals represent an increasingly transnational film culture, where audiences, filmmakers, distributors, press, critics and academics come together from all over the world to discover new films, network with one another and debate about the past, present and future of cinema. This research project investigates the role that international film festivals play within the wider international film industry, with a specific focus on emerging women filmmakers. It therefore explores the arena of contemporary women.s cinema at its intersection with the international film festival industry. The significance and original contribution of the research is its intervention in the growing field of film festival studies through a specific investigation of how international film festivals support emerging women filmmakers. The positioning of the research at the intersection of feminist film theory and festival research within the broader context of transnational cinema allows the examination of each festival, the attending filmmakers and their films to be addressed within a more refined and nuanced lens. A core method for the thesis is the close textual analysis of particular emerging women filmmakers. films which are screened at the respective festivals. The research also utilises the qualitative research strategies of the case study and the interview to ¡°seek to understand the context or setting of the participants through visiting this context and gathering information personally¡± (Creswell 2003, 9). The textual analysis is used in dialogue with the interviews and the participant observational data gathering to provide a related context for understanding these films and their cultural meanings, both personally for the filmmaker and transnationally across the festival circuit. The focus of the case studies is the Brisbane International Film Festival, the International Film Festival Rotterdam and the Toronto International Film Festival. These three festivals were chosen for their distinct geographical locations in the Asia Pacific, Europe and North America, as well as for their varying size and influence on the international film festival circuit. Specifically, I investigate the reasons behind why the organisers of a particular festival have chosen a certain woman.s film, how it is then packaged or displayed within the programme, and how all of this impacts on the filmmaker herself. The focus of my research is to investigate film festivals and their .real-life. applications and benefits for the filmmakers being supported, both through the exhibition of their films and through their attendance as festival guests. The research finds that the current generation of emerging women filmmakers has varying levels of experience and success at negotiating the international film festival circuit. Each of the three festivals examined include and promote the films of emerging women filmmakers through a range of strategies, such as specific programming strands dedicated to showcasing emerging talent, financial support through festival funds, providing visibility within the programme, exposure to international audiences and networking opportunities with industry professionals and other filmmakers. Furthermore, the films produced by the emerging women filmmakers revealed a strong focus on women.s perspectives and experiences, which were explored through the interweaving of particular aesthetic and cinematographic conventions.

Distributed low-power image processing in wireless sensor networks for intelligent video surveillance applications

Distributed Wireless Smart Camera (DWSC) network is a special type of Wireless Sensor Network (WSN) that processes captured images in a distributed manner. While image processing on DWSCs sees a great potential for growth, with its applications possessing a vast practical application domain such as security surveillance and health care, it suffers from tremendous constraints. In addition to the limitations of conventional WSNs, image processing on DWSCs requires more computational power, bandwidth and energy that presents significant challenges for large scale deployments. This dissertation has developed a number of algorithms that are highly scalable, portable, energy efficient and performance efficient, with considerations of practical constraints imposed by the hardware and the nature of WSN. More specifically, these algorithms tackle the problems of multi-object tracking and localisation in distributed wireless smart camera net- works and optimal camera configuration determination. Addressing the first problem of multi-object tracking and localisation requires solving a large array of sub-problems. The sub-problems that are discussed in this dissertation are calibration of internal parameters, multi-camera calibration for localisation and object handover for tracking. These topics have been covered extensively in computer vision literatures, however new algorithms must be invented to accommodate the various constraints introduced and required by the DWSC platform. A technique has been developed for the automatic calibration of low-cost cameras which are assumed to be restricted in their freedom of movement to either pan or tilt movements. Camera internal parameters, including focal length, principal point, lens distortion parameter and the angle and axis of rotation, can be recovered from a minimum set of two images of the camera, provided that the axis of rotation between the two images goes through the camera's optical centre and is parallel to either the vertical (panning) or horizontal (tilting) axis of the image. For object localisation, a novel approach has been developed for the calibration of a network of non-overlapping DWSCs in terms of their ground plane homographies, which can then be used for localising objects. In the proposed approach, a robot travels through the camera network while updating its position in a global coordinate frame, which it broadcasts to the cameras. The cameras use this, along with the image plane location of the robot, to compute a mapping from their image planes to the global coordinate frame. This is combined with an occupancy map generated by the robot during the mapping process to localised objects moving within the network. In addition, to deal with the problem of object handover between DWSCs of non-overlapping fields of view, a highly-scalable, distributed protocol has been designed. Cameras that follow the proposed protocol transmit object descriptions to a selected set of neighbours that are determined using a predictive forwarding strategy. The received descriptions are then matched at the subsequent camera on the object's path using a probability maximisation process with locally generated descriptions. The second problem of camera placement emerges naturally when these pervasive devices are put into real use. The locations, orientations, lens types etc. of the cameras must be chosen in a way that the utility of the network is maximised (e.g. maximum coverage) while user requirements are met. To deal with this, a statistical formulation of the problem of determining optimal camera configurations has been introduced and a Trans-Dimensional Simulated Annealing (TDSA) algorithm has been proposed to effectively solve the problem.

Steady natural convection of non-Newtonian power-law fluid in a trapezoidal enclosure

Numerically investigation of free convection heat transfer in a differentially heated trapezoidal cavity filled with non-Newtonian Power-law fluid has been performed in this study. The left inclined surface is uniformly heated whereas the right inclined surface is maintained as uniformly cooled. The top and bottom surfaces are kept adiabatic with initially quiescent fluid inside the enclosure. Finite volume based commercial software FLUENT 14.5 is used to solve the governing equations. Dependency of various flow parameters of fluid flow and heat transfer is analyzed including Rayleigh number, Ra ranging from 10^5 to 10^7, Prandtl number, Pr of 100 to 10,000 and power index, n of 0.6 to 1.4. Outcomes have been reported in terms of isotherms, streamline, and local Nusselt number for various Ra, Pr, n and inclined angles. Grid sensitivity analysis is performed and numerically obtained results have been compared with those results available in the literature and found good agreement.

Design LED innovation to rejuvenate local food systems and healthy communities : an emerging research agenda

Food Sovereignty (food freedom) is about empowering people to develop their own local food system. Food Sovereignty challenges designers to enable people to innovate the local food system, rather than having a food system which is dictated by corporate interests and failed business ethics. Communities are realising the potential for design to assist in the innovation process, and add strategic value to potentially localise the food system. Design Led Innovation (DLI) offers a strategic framework to address large-scale cultural, systemic and economic changes. The DLI approach empowers communities to take organised action to achieve a healthy, prosperous and happy way of life. DLI can assist with business models in the business world and it is evident this approach can assist with creating social change too. This paper presents on an emerging research agenda aimed to assist designer’s focus from individuals and systems to communities and urban problems. This paper also presents the research proposition that DLI and service design coupled with social entrepreneurial ventures such as local food projects and creative community inventions, have the potential to enable social innovation for healthy and happy communities.

Designing innovative business models: Five emerging meta-models

Business models to date have remained the creation of management, however, it is the belief of the authors that designers should be critically approaching, challenging and creating new business models as part of their practice. This belief portrays a new era where business model constructs become the new design brief of the future and fuel design and innovation to work together at the strategic level of an organisation. Innovation can no longer rely on technology and R&D alone but must incorporate business models. Business model innovation has become a strong type of competitive advantage. As firms choose not to compete only on price, but through the delivery of a unique value proposition in order to engage with customers and to differentiate a company within a competitive market. The purpose of this paper is to explore and investigate business model design through various product and/or service deliveries, and identify common drivers that are catalysts for business model innovation. Fifty companies spanning a diverse range of criteria were chosen, to evaluate and compare commonalities and differences in the design of their business models. The analysis of these business cases uncovered commonalities of the key strategic drivers behind these innovative business models. Five Meta Models were derived from this content analysis: Customer Led, Cost Driven, Resource Led, Partnership Led and Price Led. These five key foci provide a designer with a focus from which quick prototypes of new business models are created. Implications from this research suggest there is no ‘one right’ model, but rather through experimentation, the generation of many unique and diverse concepts can result in greater possibilities for future innovation and sustained competitive advantage.

Exploring new and emerging models for nonlinear performative works

This dissertation seeks to define and classify potential forms of Nonlinear structure and explore the possibilities they afford for the creation of new musical works. It provides the first comprehensive framework for the discussion of Nonlinear structure in musical works and provides a detailed overview of the rise of nonlinearity in music during the 20th century. Nonlinear events are shown to emerge through significant parametrical discontinuity at the boundaries between regions of relatively strong internal cohesion. The dissertation situates Nonlinear structures in relation to linear structures and unstructured sonic phenomena and provides a means of evaluating Nonlinearity in a musical structure through the consideration of the degree to which the structure is integrated, contingent, compressible and determinate as a whole. It is proposed that Nonlinearity can be classified as a three dimensional space described by three continuums: the temporal continuum, encompassing sequential and multilinear forms of organization, the narrative continuum encompassing processual, game structure and developmental narrative forms and the referential continuum encompassing stylistic allusion, adaptation and quotation. The use of spectrograms of recorded musical works is proposed as a means of evaluating Nonlinearity in a musical work through the visual representation of parametrical divergence in pitch, duration, timbre and dynamic over time. Spectral and structural analysis of repertoire works is undertaken as part of an exploration of musical nonlinearity and the compositional and performative features that characterize it. The contribution of cultural, ideological, scientific and technological shifts to the emergence of Nonlinearity in music is discussed and a range of compositional factors that contributed to the emergence of musical Nonlinearity is examined. The evolution of notational innovations from the mobile score to the screen score is plotted and a novel framework for the discussion of these forms of musical transmission is proposed. A computer coordinated performative model is discussed, in which a computer synchronises screening of notational information, provides temporal coordination of the performers through click-tracks or similar methods and synchronises the audio processing and synthesized elements of the work. It is proposed that such a model constitutes a highly effective means of realizing complex Nonlinear structures. A creative folio comprising 29 original works that explore nonlinearity is presented, discussed and categorised utilising the proposed classifications. Spectrograms of these works are employed where appropriate to illustrate the instantiation of parametrically divergent substructures and examples of structural openness through multiple versioning.

Two stage unity power factor rectifier design

This paper presents the design process utilised for producing a two stage isolated Unity Power Factor (UPF) rectifier. The important yet less intuitive aspects of the design process are highlighted to aid in the simplification of designing a power converter which meets future UPF standards. Two converter designs are presented, a 200W converter utilising a critical conduction controller and a 750W converter based around a continuous conduction controller. Both designs presented were based on the requirements of an audio power amplifier, but the processes apply equally to a range of applications.

PV string per-module maximum power point enabling converters

Many grid connected PV installations consist of a single series string of PV modules and a single DC-AC inverter. This efficiency of this topology can be enhanced with additional low power, low cost per panel converter modules. Most current flows directly in the series string which ensures high efficiency. However parallel Cúk or buck-boost DC-DC converters connected across each adjacent pair of modules now support any desired current difference between series connected PV modules. Each converter “shuffles” the desired difference in PV module currents between two modules and so on up the string. Spice simulations show that even with poor efficiency, these modules can make a significant improvement to the overall power which can be recovered from partially shaded PV strings.