Distribuição de Carabidae e Staphylinidae em agroecossistemas

O objetivo deste trabalho foi determinar a distribuição da riqueza de espécies e a preferência pelo habitat de Carabidae e Staphylinidae (Coleoptera), em áreas com rotação de soja e milho, em plantio direto e convencional, e em áreas adjacentes a estas com fragmento florestal e povoamento de pínus, respectivamente. Os besouros foram amostrados por meio de armadilhas de solo distribuídas em dois transectos de 100 m de comprimento. A distribuição da riqueza de espécies nas culturas, no fragmento florestal e no pínus foi avaliada por meio de análise de regressão linear. A análise de agrupamento foi empregada para identificar as espécies quanto à preferência pelos habitats: fragmento florestal, pínus, cultura e interface. A distribuição da riqueza de espécies de Carabidae e Staphylinidae não variou em relação à posição no transecto, enquanto a riqueza de espécies observada nas interfaces foi elevada em comparação com a encontrada nos demais habitats. A ocorrência de espécies de Carabidae diferiu conforme o tipo de cobertura vegetal: Megacephala sp. e Scarites sp. preferiram áreas cultivadas em sistema de rotação soja-milho; Odontochila nodicornis (Dejean) preferiu o fragmento florestal e o povoamento de pínus. A espécie Abaris basistriatus Chaudoir caracterizou-se como generalista quanto à preferência pelo habitat.

Distribuição do Tamanho de Poros em Cascas de Ovos Determinada pela Porosimetria de Mercúrio

Neste trabalho foi aplicada a porosimetria de mercúrio na caracterização da porosidade de cascas de ovos de poedeiras com 28 semanas de idade. Aplicando-se a técnica de porosimetria de mercúrio, pudemos descrever as características associadas a porosidade de modo mais amplo, determinando uma distribuição do tamanho de poros nas cascas de ovos estudadas. Nossos resultados mostraram que a maioria dos poros nas cascas de ovos tem tamanhos entre 1 a 10 mim. Neste artigo introduzimos a técnica de porosimetria de mercúrio como uma nova ferramenta aplicada no estudo de cascas de ovos.

Avaliação mesoscópica da origem, distribuição e ramificação do nervo radial no braço do gato doméstico (Felis catus domesticus, Linnaeus, 1758)

The present study evaluated the origin, distribution and ramification of the radial nerves were studied in 30 adult domestic cats. The sample included 15 females and 15 males of unknown breed. The specimens were fixed in 10% formaldehyde solution. The radial nerve showed many fascicles from the origin also your ramification in superficial and deep branches. Radial nerves were observed to originate, in 16 cases (26.7%), from the ventral branch of the sixth cervical spinal nerve; in 60 cases (100%), from the ventral branch of the seventh cervical spinal nerve; in 60 cases (100%), from the ventral branch of the eight cervical nerve and in 60 cases (100%), from the ventral branch of the first thoracic nerve. The radial nerves branched out, in all of the animals studied (100.0%), to the tensor fasciae antebrachii, long, accessory, medial and lateral heads of the triceps branchii and anconeus muscles. The radial nerve emits of 14 to 25 nervous branches in this region. However, the branch of the sixth cervical spinal nerve and the nervous fascicles reveal significant differences (p <= 0.05), respectively, in or with relation to sex of the animals and the studied region.

Distribuição do sistema radicular da goiabeira 'Rica' produzida a partir de estaquia herbácea

O conhecimento da distribuição do sistema radicular de plantas, principalmente de perenes, não é muito estudado, devido a inúmeros fatores, dentre os quais, a dificuldade inerente ao método de amostragem. A presente pesquisa objetivou conhecer o sistema radicular da goiabeira através do método de escavação. Utilizando jatos de água, retirou-se a terra até um volume de 10 m³ (5x5x0,4m), subdivididos em paralelepípedos de 0,1 m³ (0,5x0,5x0,4m), expondo o sistema radical da goiabeira 'Rica'. Verificou-se um vigoroso sistema radicular sem a caracterização da raiz principal e com distribuição homogênea, grande número de raízes primárias, proporcionado pela adequada formação de mudas, através de estaquia herbácea.

Perdas de nutrientes por erosão e sua distribuição espacial em área sob cana-de-açúcar

O presente trabalho teve como objetivo principal determinar as perdas de nutrientes por erosão em entressulcos, sulcos e global (entressulcos + sulcos, A), em área cultivada com cana-de-açúcar submetida à queima da palhada na sua pré-colheita, na Fazenda Santa Bárbara, localizada em Guariba - SP, sob um Latossolo Vermelho eutroférrico (LVef). Parcelas experimentais foram submetidas à chuva simulada com intensidade de 80 mm h-1, durante 65 minutos. Análises do sedimento erodido indicaram altas taxas de enriquecimento: 1,62 (matéria orgânica, MO); 4,30 (P); 1,17 (K); 1,33 (Ca) e 1,24 (Mg) vezes em relação ao solo original. As perdas de solo e nutrientes, em função do tipo de erosão, obedeceram à seguinte ordem: sulcos > global > entressulcos. Análises geoestatísticas indicaram que as perdas de solo (A), MO, P, K e Ca por erosão apresentaram forte grau de dependência espacial, enquanto as perdas de Mg tiveram moderado grau de dependência espacial. Mapas da distribuição dos padrões de variabilidade espacial das perdas por erosão indicaram que o cultivo de cana-de-açúcar conserva as propriedades químicas e físicas do solo na maior parte da área.

Cadeia produtiva da farinha de mandioca na perspectiva da análise de filière e supply chain management :um estudo de caso das relações entre a agroindústria e a distribuição

This research aims to study the manioc flour productive chain in order to understand how the relationship between its segments happens, specially between the flour agroindustry and the distribuition. This research was made from a study of case that envolved three agro industries from the Potiguar wasteland and a company of food distribution. The filiére and the supply chain management analysis were applied to identify the functioning and the organization of the manioc flour productive chain. From the study of case it s noticed that the existing contracts, even the informal ones, has mutual benefits and it suggests that they be legalized

Algoritmos de otimização para decisões de localização de facilidades e distribuição em sistemas multiníveis de transporte rodoviário de carga

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Um algoritmo para estimação de estado em alimentadores de distribuição de energia elétrica com base no método da soma de potências

Most algorithms for state estimation based on the classical model are just adequate for use in transmission networks. Few algorithms were developed specifically for distribution systems, probably because of the little amount of data available in real time. Most overhead feeders possess just current and voltage measurements at the middle voltage bus-bar at the substation. In this way, classical algorithms are of difficult implementation, even considering off-line acquired data as pseudo-measurements. However, the necessity of automating the operation of distribution networks, mainly in regard to the selectivity of protection systems, as well to implement possibilities of load transfer maneuvers, is changing the network planning policy. In this way, some equipments incorporating telemetry and command modules have been installed in order to improve operational features, and so increasing the amount of measurement data available in real-time in the System Operation Center (SOC). This encourages the development of a state estimator model, involving real-time information and pseudo-measurements of loads, that are built from typical power factors and utilization factors (demand factors) of distribution transformers. This work reports about the development of a new state estimation method, specific for radial distribution systems. The main algorithm of the method is based on the power summation load flow. The estimation is carried out piecewise, section by section of the feeder, going from the substation to the terminal nodes. For each section, a measurement model is built, resulting in a nonlinear overdetermined equations set, whose solution is achieved by the Gaussian normal equation. The estimated variables of a section are used as pseudo-measurements for the next section. In general, a measurement set for a generic section consists of pseudo-measurements of power flows and nodal voltages obtained from the previous section or measurements in real-time, if they exist -, besides pseudomeasurements of injected powers for the power summations, whose functions are the load flow equations, assuming that the network can be represented by its single-phase equivalent. The great advantage of the algorithm is its simplicity and low computational effort. Moreover, the algorithm is very efficient, in regard to the accuracy of the estimated values. Besides the power summation state estimator, this work shows how other algorithms could be adapted to provide state estimation of middle voltage substations and networks, namely Schweppes method and an algorithm based on current proportionality, that is usually adopted for network planning tasks. Both estimators were implemented not only as alternatives for the proposed method, but also looking for getting results that give support for its validation. Once in most cases no power measurement is performed at beginning of the feeder and this is required for implementing the power summation estimations method, a new algorithm for estimating the network variables at the middle voltage bus-bar was also developed

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Determinação de Chaveamento para Recomposição do Serviço em Redes de Distribuição de Energia Elétrica em Média Tensão Através de Métodos Baseado em Parâmetros de Sensibilidade

The reconfiguration of a distribution network is a change in its topology, aiming to provide specific operation conditions of the network, by changing the status of its switches. It can be performed regardless of any system anomaly. The service restoration is a particular case of reconfiguration and should be performed whenever there is a network failure or whenever one or more sections of a feeder have been taken out of service for maintenance. In such cases, loads that are supplied through lines sections that are downstream of portions removed for maintenance may be supplied by the closing of switches to the others feeders. By classical methods of reconfiguration, several switches may be required beyond those used to perform the restoration service. This includes switching feeders in the same substation or for substations that do not have any direct connection to the faulted feeder. These operations can cause discomfort, losses and dissatisfaction among consumers, as well as a negative reputation for the energy company. The purpose of this thesis is to develop a heuristic for reconfiguration of a distribution network, upon the occurrence of a failure in this network, making the switching only for feeders directly involved in this specific failed segment, considering that the switching applied is related exclusively to the isolation of failed sections and bars, as well as to supply electricity to the islands generated by the condition, with significant reduction in the number of applications of load flows, due to the use of sensitivity parameters for determining voltages and currents estimated on bars and lines of the feeders directly involved with that failed segment. A comparison between this process and classical methods is performed for different test networks from the literature about networks reconfiguration

Um estimador de estado trifásico para sistemas de distribuição de energia elétrica com base no método da soma de potências

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Análise espacial da distribuição longitudinal de sementes de milho em uma semeadora-adubadora de precisão

In the operation of sowing with planter numerous factors interfere with the establishment of the plant stand, among them, the longitudinal distribution of seeds depending on the displacement speed can significantly affect crop productivity.The present study aimed the evaluation of longitudinal distribution of maize seeds in two different speeds of dislocation of a precision grain drill, through classical and geostatistics. A regular grid sample, totalizing 100 points in each area, was built with 10-meter distance among the points. Each sample point comprised 3.6m(2) (1.8 x 2.0) where the percentage of acceptable, double and fail spacing among the plants was measured after sowing at 4.58 and 5.94 km h(-1) speed of dislocation. Classical and geostatistics were used for data analyses. The percentage of acceptable and failed spacing has shown significant difference between 4.58 and 5.94 km h(-1) speed. The results has shown absence of spatial dependence regarding the percentage of the studied spacing (acceptable, fail and double) at both speeds, showing that studies and statistical inferences can occur based on parameters of classical statistics for distances higher than the shortest one used in the sampling.

Distribuição radicular de cultivares de aspargo em áreas irrigadas de Petrolina - PE

A distribuição radicular de duas cultivares de aspargo (New Jersey 220 e UC 157 F1), irrigadas por aspersão convencional, foi avaliada durante o ano de 1997 em solos de textura arenosa, em plantio experimental e comercial, respectivamente, nos Projetos de Irrigação de Bebedouro e Senador Nilo Coelho, em Petrolina (PE). O objetivo foi obter informações do sistema radicular do aspargo, empregando-se os métodos do monolito e do perfil de solo auxiliado pela análise de imagens digitais, para o manejo de solo e água nesse cultivo. Na área experimental, a maior parte da matéria seca, área e comprimento de raízes no perfil de solo e densidade de comprimento radicular foram encontradas até a profundidade de 0,4 m nas duas cultivares, enquanto que na comercial a maior parte da área e comprimento de raízes no perfil do solo estendeu-se até a profundidade de 0,6 m (cv. New Jersey 220). Nesses dois plantios, as raízes das cultivares atingiram a profundidade de 1 m. Na área experimental, a massa seca, a área e o comprimento no perfil de solo, e a densidade de comprimento radicular nas cultivares concentraram-se até a distância de 0,6 m à linha de plantas. No intervalo de diâmetro (d) de raízes 2de raízes variou entre 2,4 e 2,6 mm (cv. New Jersey 220) e 2,4 e 3,6 mm (cv. UC 157 F1). As estimativas da distribuição e do diâmetro radicular apresentaram similaridades considerando os métodos empregados.

Um sistema para simular o comportamento de bancos trifásicos de reguladores de tensão usados em sistemas de distribuição de energia elétrica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior