Branding and Marketing Communications of Lifestyle Prescription Drugs in a Strict Legislative Environment

This thesis discusses the different possibilities to brand and promote a patented prescription lifestyle drug through different marketing communications practices. This thesis aims in explaining how branding procedures can be built in circumstances, where the legislative environment is strickt and furthermore, the environment consists of both B-to-B and B-to-C market characteristics simultaneously.

The oxygenation in biological wastewater treatment of pulp and paper industry

The UPM-Kymmene Oyj Pietarsaari pulp and paper Mill biological wastewater treatment plant was built in the 1980's and the plant has been in use ever since. During the past years there have been problems with deviations. The wastewater treatment plant needs update, especially the aeration basin, where the old surface aerators cannot produce enough mixing and indroduce oxygen enough to the wastewater. In this thesis how extra aeration with oxygen affects the wastewater treatment plant effluent was studied. In the literature part the main focus is in aeration devices, which can be used in biological wastewater treatment. The target is to compare different kind of aerators, which are suitable for pulp and paper wastewater treatment. Studies show, that EDI-aerators are commonly used and also most suitable. In the experimental part, the focus is on the Pietarsaari Mills wastewater treatment plant and oxygen aeration during autumn 2008. This thesis presents the results of the trial run. Studies show, that extra oxygen devices can produce lot a of mixing and the oxygenation capacity was more than what the micro-organisms needed. The effect on sludge quality could not been seen during the trial runs.

Determination of sulfur in diesel using ATR/FTIR and multivariate calibration

The aim of this present work was to provide a more fast, simple and less expensive to analyze sulfur content in diesel samples than by the standard methods currently used. Thus, samples of diesel fuel with sulfur concentrations varying from 400 and 2500 mgkg-1 were analyzed by two methodologies: X-ray fluorescence, according to ASTM D4294 and by Fourier transform infrared spectrometry (FTIR). The spectral data obtained from FTIR were used to build multivariate calibration models by partial least squares (PLS). Four models were built in three different ways: 1) a model using the full spectra (665 to 4000 cm-1), 2) two models using some specific spectrum regions and 3) a model with variable selected by classic method of variable selection stepwise. The model obtained by variable selection stepwise and the model built with region spectra between 665 and 856 cm-1 and 1145 and 2717 cm-1 showed better results in the determination of sulfur content.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.

"Luottamus on aika kovaa tässä" - Luottamuksen rakentuminen innovaatioyhteistyössä

Pro gradu -tutkielman tavoitteena on tutkia luottamuksen rakentumista in-novaatioyhteistyössä. Tarkoituksena on selvittää miten luottamus rakentuu ja mitkä tekijät vaikuttavat luottamuksen rakentumisen taustalla. Samalla pohditaan, miten luottamuksen rakentumista voidaan tietoisesti tukea. Lisäksi mietitään luottamuksen merkitystä innovaatioyhteistyössä ja sen roolia innovaatiossa onnistumisessa. Tutkimusaineisto kerättiin kvalitatii-visten teemahaastattelujen avulla. Tutkimuksen perusteella saatiin selkeä kuva siitä, miten luottamus raken-tuu innovaatioyhteistyössä, mitkä tekijät sen rakentumiseen vaikuttavat ja miten sen rakentumista voidaan tukea. Innovaatioverkostossa esiintyvä luottamus rakentui osaamisen, identiteetin ja hyväntahtoisuuden varaan ja oli sekä organisaatioiden että yksilöiden välistä. Sen rakentumisessa osaava orkesterointi oli tärkeässä roolissa. Tutkimuksen kohteena ollut kehitystyö ei olisi onnistunut ilman luottamusta ja osin luottamuksen puutteen vuoksi kaikkia tavoitteita ei saavutettu.

Thinking Outside the Box: Enhancing Science Teaching by Combining (Instead of Contrasting) Laboratory and Simulation Activities

The focus of the present work was on 10- to 12-year-old elementary school students’ conceptual learning outcomes in science in two specific inquiry-learning environments, laboratory and simulation. The main aim was to examine if it would be more beneficial to combine than contrast simulation and laboratory activities in science teaching. It was argued that the status quo where laboratories and simulations are seen as alternative or competing methods in science teaching is hardly an optimal solution to promote students’ learning and understanding in various science domains. It was hypothesized that it would make more sense and be more productive to combine laboratories and simulations. Several explanations and examples were provided to back up the hypothesis. In order to test whether learning with the combination of laboratory and simulation activities can result in better conceptual understanding in science than learning with laboratory or simulation activities alone, two experiments were conducted in the domain of electricity. In these experiments students constructed and studied electrical circuits in three different learning environments: laboratory (real circuits), simulation (virtual circuits), and simulation-laboratory combination (real and virtual circuits were used simultaneously). In order to measure and compare how these environments affected students’ conceptual understanding of circuits, a subject knowledge assessment questionnaire was administered before and after the experimentation. The results of the experiments were presented in four empirical studies. Three of the studies focused on learning outcomes between the conditions and one on learning processes. Study I analyzed learning outcomes from experiment I. The aim of the study was to investigate if it would be more beneficial to combine simulation and laboratory activities than to use them separately in teaching the concepts of simple electricity. Matched-trios were created based on the pre-test results of 66 elementary school students and divided randomly into a laboratory (real circuits), simulation (virtual circuits) and simulation-laboratory combination (real and virtual circuits simultaneously) conditions. In each condition students had 90 minutes to construct and study various circuits. The results showed that studying electrical circuits in the simulation–laboratory combination environment improved students’ conceptual understanding more than studying circuits in simulation and laboratory environments alone. Although there were no statistical differences between simulation and laboratory environments, the learning effect was more pronounced in the simulation condition where the students made clear progress during the intervention, whereas in the laboratory condition students’ conceptual understanding remained at an elementary level after the intervention. Study II analyzed learning outcomes from experiment II. The aim of the study was to investigate if and how learning outcomes in simulation and simulation-laboratory combination environments are mediated by implicit (only procedural guidance) and explicit (more structure and guidance for the discovery process) instruction in the context of simple DC circuits. Matched-quartets were created based on the pre-test results of 50 elementary school students and divided randomly into a simulation implicit (SI), simulation explicit (SE), combination implicit (CI) and combination explicit (CE) conditions. The results showed that when the students were working with the simulation alone, they were able to gain significantly greater amount of subject knowledge when they received metacognitive support (explicit instruction; SE) for the discovery process than when they received only procedural guidance (implicit instruction: SI). However, this additional scaffolding was not enough to reach the level of the students in the combination environment (CI and CE). A surprising finding in Study II was that instructional support had a different effect in the combination environment than in the simulation environment. In the combination environment explicit instruction (CE) did not seem to elicit much additional gain for students’ understanding of electric circuits compared to implicit instruction (CI). Instead, explicit instruction slowed down the inquiry process substantially in the combination environment. Study III analyzed from video data learning processes of those 50 students that participated in experiment II (cf. Study II above). The focus was on three specific learning processes: cognitive conflicts, self-explanations, and analogical encodings. The aim of the study was to find out possible explanations for the success of the combination condition in Experiments I and II. The video data provided clear evidence about the benefits of studying with the real and virtual circuits simultaneously (the combination conditions). Mostly the representations complemented each other, that is, one representation helped students to interpret and understand the outcomes they received from the other representation. However, there were also instances in which analogical encoding took place, that is, situations in which the slightly discrepant results between the representations ‘forced’ students to focus on those features that could be generalised across the two representations. No statistical differences were found in the amount of experienced cognitive conflicts and self-explanations between simulation and combination conditions, though in self-explanations there was a nascent trend in favour of the combination. There was also a clear tendency suggesting that explicit guidance increased the amount of self-explanations. Overall, the amount of cognitive conflicts and self-explanations was very low. The aim of the Study IV was twofold: the main aim was to provide an aggregated overview of the learning outcomes of experiments I and II; the secondary aim was to explore the relationship between the learning environments and students’ prior domain knowledge (low and high) in the experiments. Aggregated results of experiments I & II showed that on average, 91% of the students in the combination environment scored above the average of the laboratory environment, and 76% of them scored also above the average of the simulation environment. Seventy percent of the students in the simulation environment scored above the average of the laboratory environment. The results further showed that overall students seemed to benefit from combining simulations and laboratories regardless of their level of prior knowledge, that is, students with either low or high prior knowledge who studied circuits in the combination environment outperformed their counterparts who studied in the laboratory or simulation environment alone. The effect seemed to be slightly bigger among the students with low prior knowledge. However, more detailed inspection of the results showed that there were considerable differences between the experiments regarding how students with low and high prior knowledge benefitted from the combination: in Experiment I, especially students with low prior knowledge benefitted from the combination as compared to those students that used only the simulation, whereas in Experiment II, only students with high prior knowledge seemed to benefit from the combination relative to the simulation group. Regarding the differences between simulation and laboratory groups, the benefits of using a simulation seemed to be slightly higher among students with high prior knowledge. The results of the four empirical studies support the hypothesis concerning the benefits of using simulation along with laboratory activities to promote students’ conceptual understanding of electricity. It can be concluded that when teaching students about electricity, the students can gain better understanding when they have an opportunity to use the simulation and the real circuits in parallel than if they have only the real circuits or only a computer simulation available, even when the use of the simulation is supported with the explicit instruction. The outcomes of the empirical studies can be considered as the first unambiguous evidence on the (additional) benefits of combining laboratory and simulation activities in science education as compared to learning with laboratories and simulations alone.

Modelling of calciner in post-combustion carbon capture process

Climate change has given an impetus to research and developed new technologies to reduce significantly carbon dioxide emissions in energy production in the developed countries. The major pollution source, fossil fuels, will be used as an energy source for many decades, which provides the demand for carbon capture and storage technologies. Over recent years many new technologies has been developed and one of the most promising is calcium-looping in post-combustion carbon capture process, which use carbonation-calcination cycle to capture carbon dioxide from the flue gas of a combustion process. First pilot plant for calcium-looping process has been built in Oviedo, Spain. In this study, a three-dimensional model has been created for the calciner, which is one of the two fluidized bed reactors needed for the process. The calciner is a regenerator where the captured carbon dioxide is removed from the calcium material and then collected after the reactor. Thesis concentrates in creating the calciner 3D-model frame with CFB3D-program and testing the model with two different example cases. Used input parameters and calciner geometry are Oviedo pilot plant design parameters. The calculation results give information about the process and show that pilot plant calciner should perform as planned. This Master’s Thesis is done in participation to EU FP7 project CaOling.

Utilization of Particle Image velocimetry in PPOOLEX condensation experiments

Particle Image Velocimetry, PIV, is an optical measuring technique to obtain velocity information of a flow in interest. With PIV it is possible to achieve two or three dimensional velocity vector fields from a measurement area instead of a single point in a flow. Measured flow can be either in liquid or in gas form. PIV is nowadays widely applied to flow field studies. The need for PIV is to obtain validation data for Computational Fluid Dynamics calculation programs that has been used to model blow down experiments in PPOOLEX test facility in the Lappeenranta University of Technology. In this thesis PIV and its theoretical background are presented. All the subsystems that can be considered to be part of a PIV system are presented as well with detail. Emphasis is also put to the mathematics behind the image evaluation. The work also included selection and successful testing of a PIV system, as well as the planning of the installation to the PPOOLEX facility. Already in the preliminary testing PIV was found to be good addition to the measuring equipment for Nuclear Safety Research Unit of LUT. The installation to PPOOLEX facility was successful even though there were many restrictions considering it. All parts of the PIV system worked and they were found out to be appropriate for the planned use. Results and observations presented in this thesis are a good background to further PIV use.

Cysticercosis in experimentally and naturally infected pigs: parasitological and immunological diagnosis

Our objective was to evaluate the diagnosis of swine cysticercosis by examining "ante mortem" (inspection of the tongue), "post mortem" (inspection and detailed necropsy) and ELISA for research in serum of antibodies (Ab-ELISA) and antigens (Ag-ELISA). Seven (7) pigs were experimentally infected orally with eggs of Taenia solium and another 10 were naturally infected. In the pigs experimentally infected, inspection of the tongue was negative in all animals, in the routine inspection detailed necropsy and cysticercis were identified in all of them. In pigs with heavy natural infection, inspection of the tongue identified cysticerci in two (20%), while at inspection with necropsy the parasites were identified in large quantities in all animals. In ELISA for antibody search (Ab-ELISA) TS-14 recombinant protein was used, and in search for antigen (Ag-ELISA) a monoclonal antibody against this protein. In animals experimentally infected, blood was collected weekly for 140 days. The Ab-ELISA identified an increase in titers of antibody to cysticerci 21 days after infection, and at the end of the experimental period six animals (86%) were positive to the test. The search for circulating antigens (Ag-ELISA) was positive in two pigs 28 to 91 days after infection. All naturally infected pigs were positive for Ag-ELISA and Ab-ELISA. The search for antibodies and antigens by ELISA in serum from 30 pigs of a local farm and without history of cysticercosis was negative. Thus, the use of TS-14 antigen in ELISA test (Ab-ELISA) can be useful for the diagnosis of cysticercosis in pigs with low infection.

Professional sports and gambling regulation in Finland - Examining the institutional factors of gambling affecting professional sport clubs in Finland

This study examines how to institutional environment of gambling is currently in motion both in Europe and Finland. Furthermore, it examines the criticism by Finnish professional sport clubs directed towards the national gambling monopolies, especially Veikkaus Oy. This criticism addresses the acclaimed issue of low or non-existing sponsorship funds coming to the clubs despite the clubs’ duties to promote Veikkaus Oy in their stadiums etc. In essence the main research objective was to examine the interaction and institutional environments of both Finnish professional sport clubs and gambling regulation. This was done through three sub-objectives: 1) to analyze professional sport as business and its institutional environment 2) to analyze the institutions of gambling in their current state and their potential future 3) to evaluate the potential impact of an institutional change in gambling legislation to the professional sport clubs The findings from Finland were then compared to those of Denmark where an institutional change had occurred in gambling regulation. Empirical data was collected through multiple interviews. Interviewees represented sport clubs (7), sport association (1), sport league (1), Finnish monopoly representatives (2), commercial gambling providers (1), Danish monopoly system representatives (1), Danish sport club (1). In addition a vast amount of secondary data (e.g. Green and white books by EU, court decisions, a variety of studies etc.). Theoretically this study combines the aspects of institutional theory with the theory of professional sports as business. This proved to be a rather new approach and no published literature was found to have done specifically this. The findings of this study are twofold, on the European level it is clear that the momentum if towards a more liberated gambling market while Finland is at the moment trying to go the opposite direction and uphold its monopoly. From the sport club’s level the findings suggest that currently sport clubs do not directly benefit from the funds originated from Veikkaus Oy as these funds are more or less used on the association/league levels. However, the clubs themselves are also lacking in self-criticism as they are lacking in clear sponsorship packages/programs which Veikkaus Oy might be interested in participating. If liberation of the gambling market would occur it is highly possible that that the largest clubs in football and ice-hockey would be the main beneficiaries while smaller clubs and sports could possibly be worse off than currently. These interpretations were well supported by the findings from Denmark.

Dynamics of coherent vortices in mixing layers using direct numerical and large-eddy simulations

Coherent vortices in turbulent mixing layers are investigated by means of Direct Numerical Simulation (DNS) and Large-Eddy Simulation (LES). Subgrid-scale models defined in spectral and physical spaces are reviewed. The new "spectral-dynamic viscosity model", that allows to account for non-developed turbulence in the subgrid-scales, is discussed. Pseudo-spectral methods, combined with sixth-order compact finite differences schemes (when periodic boundary conditions cannot be established), are used to solve the Navier- Stokes equations. Simulations in temporal and spatial mixing layers show two types of pairing of primary Kelvin-Helmholtz (KH) vortices depending on initial conditions (or upstream conditions): quasi-2D and helical pairings. In both cases, secondary streamwise vortices are stretched in between the KH vortices at an angle of 45° with the horizontal plane. These streamwise vortices are not only identified in the early transitional stage of the mixing layer but also in self-similar turbulence conditions. The Re dependence of the "diameter" of these vortices is analyzed. Results obtained in spatial growing mixing layers show some evidences of pairing of secondary vortices; after a pairing of the primary Kelvin-Helmholtz (KH) vortices, the streamwise vortices are less numerous and their diameter has increased than before the pairing of KH vortices.

Covalidation of Integral Transforms and Method of Lines in Nonlinear Convection-Diffusion with Mathematica

The Mathematica system (version 4.0) is employed in the solution of nonlinear difusion and convection-difusion problems, formulated as transient one-dimensional partial diferential equations with potential dependent equation coefficients. The Generalized Integral Transform Technique (GITT) is first implemented for the hybrid numerical-analytical solution of such classes of problems, through the symbolic integral transformation and elimination of the space variable, followed by the utilization of the built-in Mathematica function NDSolve for handling the resulting transformed ODE system. This approach ofers an error-controlled final numerical solution, through the simultaneous control of local errors in this reliable ODE's solver and of the proposed eigenfunction expansion truncation order. For covalidation purposes, the same built-in function NDSolve is employed in the direct solution of these partial diferential equations, as made possible by the algorithms implemented in Mathematica (versions 3.0 and up), based on application of the method of lines. Various numerical experiments are performed and relative merits of each approach are critically pointed out.

Using Moodle to provide added value in the teaching of a software development course

The rate of adoption and use of learning management systems to support teaching and learning processes in academic institutions is growing rapidly. Universities are acquiring systems with functionalities that can match with their specific needs and requirements. Moodle is one of the most popular and widely deployed learning management systems in academic institutions today. However, apart from the system, universities tend to maintain other applications for the purpose of supplementing their teaching and learning processes. This situation is similar to Lappeenranta University of Technology (LUT), which is our case study in this project. Apart from Moodle, the university also maintains other systems such as Oodi, Noppa and Uni portal for the purpose of supporting its educational activities. This thesis has two main goals. The first goal is to understand the specific role of Moodle at LUT. This information is fundamental in assessing whether Moodle is needed in the university’s current teaching and learning environment. The second aim is to provide insights to teachers and other departmental stakeholders on how Moodle can provide added value in the teaching of a software development course. In response to this, a Moodle module for a software development course is created and the underlying features are tested. Results of the constructive work proposed some improvements through (i) the use of Moodle for in-class surveys, (ii) transfer of grades from Moodle to Oodi, (iii) use of Moodle in self-study courses and MOOCs, (iv) online examinations, and (v) Moodle integrations with third party applications. The proposed items were then evaluated for their utility through interviews of five expert interviews. The final results of this work are considered useful to LUT administration and management specifically on ways that Moodle can bring changes to the university at managerial, economical and technical level. It also poses some challenges on platform innovations and research.

Use of fiber-reinforced composite framework and thermochromic pigment in maxillofacial prostheses

The purpose of this investigation was to evaluate the possibility to enhance certain qualities of facial prostheses. Polymethyl methacrylate is still being used as base mate¬rial or clip carrier material, but it is hard and heavy, and debonding of the silicone from the acrylic base material is a frequent problem. This thesis aims to evaluate the use of fiber-reinforced composite (FRC) as framework material for maxillofacial silicone prostheses. FRC has been used as reinforcement in removable and fixed partial dentures since the 1990s. This material is lightweight and can be fabricated to compress the margins of the prosthesis slightly, to keep it tightly against the skin during jaw movements and facial expressions. Additionally, the use of a thermochromic pigment, colorless in room temperature and red in a cold environment, was studied in order to evaluate the possibility of using this color changing pigment in facial prostheses to mimic the color change of facial skin in cold weather. The tensile bond strength between pre-impregnated, unidirectional FRC and maxillofacial silicone elastomer was studied. Three different bonding agents or primers were compared. Bond strength was improved by one of the primers and by roughening the surface. The effect of a skin compressing glass fiber-reinforced composite framework on facial skin blood flow was studied by using a face mask, constructed with a compression pad corresponding to the outer margin of a glass fiber-reinforced framework beam of a facial prosthesis. The skin blood flow of ten healthy volunteers, aged 23-25 years, was measured during touch, light, and moderate compression of the skin, by using laser Doppler imaging technique. None of the compressions showed any marked effects on local skin blood flow. There were no significant differences between blood flow during compression and at baseline. Maxillofacial silicone elastomer was colored intrinsically with conventional color pigments: a control group containing only conventional pigments was compared to two test groups with 0.2 wt% and 0.6 wt% thermochromic pigment added. The color of the material was measured with a spectrophotometer in room temperature and after storage in a freezer. The color stability of the maxillofacial silicone elastomer colored with thermo¬chromic pigment was evaluated by artificial aging. The color dif¬ference of the L* (lightness) and a* values (redness), comparing color after the samples were stored at room temperature and in a freezer (-19°C), was statistically significant for both 0.2 wt% and 0.6 wt% thermo¬chromic pigment groups. The differences in the b* values (yellowness) were statistically significant for the 0.6 wt% group. Exposure to ultraviolet (UV) radiation led to visually noticeable and statistically signifi¬cant color changes (ΔE) in all color values in both test groups. The specimens containing thermochromic pigment were very sensitive to UV radiation. In conclusion, a framework of fiber-reinforced composite can successfully be bonded to maxillofacial silicone elastomer, and a framework beam, compressing the facial skin, did not remarkably alter the skin blood flow on healthy, young adults. The thermochromic pigment showed color change in maxillofacial silicone elastomer. However, artificial aging showed that it was too sensitive to UV radiation to be used, as such, in maxillofacial prostheses.

The Use of Nervous System Drugs and the Risk of Fractures in Old Adults

Hermostoon vaikuttavien lääkkeiden käyttö on yleistä iäkkäässä väestössä. Erityisen yleistä käyttö on pitkäaikaisessa laitoshoidossa asuvilla iäkkäillä. Hermostoon vaikuttavien lääkkeiden haittavaikutuksia on tutkittu paljon, ja useat hermostoon vaikuttavat lääkeaineryhmät on tunnistettu murtumien riskitekijöiksi. Aikaisemmin ei ole kuitenkaan tutkittu usean hermostoon vaikuttavan lääkkeen yhteiskäytön yhteyksiä murtuman riskiin 65 vuotta täyttäneillä. Väitöskirjatutkimuksessa havaittiin, että usean hermostoon vaikuttavan lääkeaineen yhtäaikainen käyttö oli hyvin yleistä Porin kaupunginsairaalan viidellä pitkäaikaisen laitoshoidon osastolla (n = 154) vuosien 2004 ja 2005 vaihteessa. Kolmasosa tutkituista käytti säännöllisesti kolmea tai useampaa hermostoon vaikuttavaa lääkettä samanaikaisesti. Kun huomioitiin myös tarvittaessa otettavat lääkkeet, vastaava luku oli 53 %. Tutkimuksessa havaittiin myös viitteitä lääkkeiden epäasianmukaisesta käytöstä, kun potilaiden käyttämiä lääkkeitä verrattiin heidän kognitiiviseen ja fyysiseen suorituskyynsä sekä asetettuihin diagnooseihin. Liedon kunnassa 1990-luvulla toteutettuun väestöpohjaiseen Liedon Iäkkäät -seurantatutkimukseen osallistui 1177 lietolaista 65 vuotta täyttänyttä. Lääkitystietoja sekä seuranta-aikana tapahtuneita murtumia analysoimalla havaittiin, että kahden tai useamman bentsodiatsepiinin sekä kahden tai useamman psykoosilääkkeen käyttö oli yhteydessä murtuman riskiin 65 vuotta täyttäneillä miehillä. Opioidin ja psykoosilääkkeen yhteiskäyttö sekä opioidin ja bentsodiatsepiinin yhteiskäyttö oli yhteydessä iäkkäiden miesten murtuman riskiin. Naisilla vastaavia tilastollisesti merkitseviä yhteyksiä ei havaittu. Väitöskirjatutkimuksen uusin osa-aineisto perustui Porissa vuosina 2009–2010 toteutetun Satauni-tutkimuksen aineistoon. Tutkimuksessa osoitettiin 89 potilaan aineistossa, että hallittu, yhden kuukauden aikana lääkärin ja hoitajan tuella toteutettu bentsodiatsepiinivieroitus paransi merkitsevästi 55 vuotta täyttäneiden naisten käden puristusvoimaa kuuden kuukauden seuranta-aikana. Vastaavaa yhteyttä ei havaittu miehillä. Bentsodiatsepiinivieroituksella ei ollut yhteyttä osallistujien tasapainotestin tulosten paranemiseen kuuden kuukauden seurantaaikana. Murtumilla on vakavia seurauksia sekä yksilötasolla että yhteiskunnallisesti iäkkäässä väestössä. Murtumien ehkäisy on hyvin tärkeää. Siinä tulee kiinnittää huomiota potilaan käyttämään lääkitykseen ja arvioida erityisesti usean hermostoon vaikuttavan lääkkeen yhteiskäytön tarpeellisuutta.