The potential of novel primers and universal adhesives to bond to zirconia

Objectives: To investigate the adhesive potential of novel zirconia primers and universal adhesives to surface-treated zirconia substrates.Methods: Zirconia bars were manufactured (3.0 mm x 3.0 mm x 9.0 mm) and treated as follows: no treatment (C); air abrasion with 35 mu m alumina particles (S); air abrasion with 30 mu m silica particles using one of two systems (Rocatec or SilJet) and; glazing (G). Groups C and S were subsequentially treated with one of the following primers or adhesives: ZP (Z-Prime Plus), AZ (AZ Primer); MP (Monobond Plus); SU (ScotchBond Universal) and; EA (an Experimental Adhesive). Groups Rocatec and SilJet were silanized prior to cementation. Samples form group G were further etched and silanized. Bars were cemented (Multilink) onto bars of a silicate-based ceramic (3.0 mm x 3.0 mm x 9.0 mm) at 90 degrees angle, thermocycled (2.500 cycles, 5-55 degrees C, 30 s dwell time), and tested in tensile strength test. Failure analysis was performed on fractured specimens to measure the bonding area and crack origin.Results: Specimens from group C did not survive thermocycling, while CMP, CSU and CEA groups survived thermocycling but rendered low values of bond strength. All primers presented a better bond performance after air abrasion with Al2O3 particles. SilJet was similar to Rocatec, both presenting the best bond strength results, along with SMP, SSU and CEA. G promoted intermediate bond strength values. Failure mode was predominately adhesive on zirconia surface combined to cohesive of the luting agent.Conclusions: Universal adhesives (MP, SU, EA) may be a considerable alternative for bonding to zirconia, but air abrasion is still previously required. Air abrasion with silica particles followed by silane application also presented high bond strength values. (C) 2013 Elsevier Ltd. All rights reserved.

Caracterização de superfície, adesiva e mecânica de uma zircônia parcialmente estabilizada por ítria em função da partícula ou do momento do jateamento

Pós-graduação em Reabilitação Oral - FOAR

Gas sensor applications of zinc oxide thin film grown by the polymeric precursor method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Lead-free BaBi4Ti4O15 ceramics: Effect of synthesis methods on phase formation and electrical properties

The processing of ferroelectric BaBi4Ti4O15 (BBT) ceramics from powders prepared by conventional solid state reaction (SSR) and mechanochemical activation (MA) has been investigated. It was shown that MA synthesis reduces the synthesis temperature of BBT powders, leading to smaller particles with reduced anisotropy and consequently to smaller grain size of ceramics. Dielectric properties were investigated in a wide range of temperatures (20-800 degrees C) and frequencies (1.21 kHz to 1 MHz). The relative dielectric permittivity at Curie temperature was higher for solid state obtained ceramics than for the mechanically treated ones. The conductivity of sintered samples was studied, suggesting decreasing of conductivity of BBT-MA in comparison with BBT-SS ceramics. The influence of the grain and the grain boundaries contribution to the dielectric behavior in both ceramics was analyzed through impedance spectroscopy. A well-defined ferroelectric hysteresis loop was obtained for both samples. (C) 2014 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Quantitative phase analysis from X-ray diffraction in Y-TZP dental ceramics: A critical evaluation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Polishing for glass ceramics: Which protocol?

Purpose: The execution of adjustments on ceramic restorations is sometimes necessary for either correction of occlusion and/or inadequate contours or esthetical improvements. Clinically, the surfaces undergo weariness through fine grinding diamond burs which remove the superficial glazing layer. Several materials for ceramic polishing have been used in an attempt to reach a satisfactory surface smoothness. The aim of this study was to perform a literature review on different polishing protocols of several dental ceramics. Study selection: This is a literature review performed through scientific articles published between 2004 and 2012, indexed in MEDLINE, PubMed and Scielo databases. The study selected and analyzed a total of 20 relevant articles that evaluated different types of ceramics, polishing treatment and surface roughness.Results: After an extensive literature review, this study observed: 1 - after the rupture of the glazing layer due to the adjustments of the restorations, the best choice for the polishing of the surface will depend on the type of ceramics used; 2 - glazing procedure provide excellent results regarding to the superficial smoothness; however, if reglazing is impossible, either abrasive rubber cups/points or sandpaper discs followed by the use of diamond polishing pastes results in a satisfactory superficial smoothness; 3 - clinical studies that take into account the behavior of the protocols polishing are scarce and should be encouraged; 4 - the large number of variables influence the final outcome of polishing should be considered. Conclusions: The necessity in standardization of methodologies to enable a comparison among researches. (c) 2014 Japan Prosthodontic Society. Published by Elsevier Ireland. All rights reserved.

Effect of surface treatment on the bond strength between yttria partially stabilized zirconia ceramics and resin cement

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Comparison of polymers and ceramics in new and discarded electrical insulators: reuse and recycling possibilities

The expansion and maintenance of electricity distribution networks generates large amounts of waste, much of it in the form of discarded insulators that are not reused or recycled. This paper describes the results of tests on used and new ceramic and polymeric insulators to verify if their exposure to weathering justifies their replacement. In new and used ceramic insulators, properties such as contact angle, relative density, porosimetry, dilatometry and X-ray diffraction patterns showed no differences or the differences that were found could not be related to their use. The discarded ceramic material showed high thermal stability, an interesting characteristic for application as chamotte. It can also be reused to replace gravel used in substations. In polymeric insulators, thermogravimetry, differential scanning calorimetry and relative density test results suggest degradation of used material compared to new. This would justify their replacement and discard as waste, but they show little recycling potential.

Caracterização geológica do perfil laterítico no município de Rondon do Pará, bloco sul do projeto Alumina Rondon

This completion of course work has as its object of study the Bauxite Province of Paragominas regarded as the richest Amazon bauxite province and whose genesis is related to laterization processes responsible for the formation of mineral deposits of the Rondon Alumina Project, designed to assess areas in the southeast of Pará State, for mineral resources exploration of bauxite, which is the main source of aluminum in the country. Located in the region of Rondon do Pará - PA, the study area is geologically inserted in Lithostratigraphic Unit called Cobertura Laterítica Matura (Mature Lateritic Cover), formed by alteration of paleotropics Cretaceous siliciclastic rocks, and its geomorphology corresponds to a broad plateau with displays of representative profiles of the processes that acted in the region. In this context, the present research aims to characterize the geological evolution of the laterite profile, with detailed studies in the area, geological description of the formations from the bauxite surfaces, and mineralogical composition litochemical of different horizons that were correlated and deployed in an evolutionary model compatible with its traits. The data collected during the analysis subsidized metalogenetic understanding of the processes that acted in the enrichment of aluminum and iron as well as the redistribution of the latter modified profile. The results and information were embodied in the form of geological characterization of the different constituents of mineral associations of bauxite horizons, similarities or differences in both textural and structural aspects, in order to propose a evolutionary model with retaken of gibbsitization processes

Vitrocerâmicas porosas via conformação e consolidação com amidos

The search for new methods of manufacture of glass-ceramics with controlled porosity and permeability is interesting of the industrial and commercial point of view, and a challenge of great complexity. Porous glass-ceramics produced by sintering and crystallization of glasses can find applications, for example, as filters, materials with bactericidal properties, bio-implants, as catalytic and enzymes supports, among others. An alternative and low cost method of ceramic manufacture reaching different levels of porosity, for diverse purposes, is the conformation assisted by addition of starch, known as consolidation with starch. The objective of this project is to study the process of conformation with starch for making porous glass-ceramics from a commercial glass in the system Na2O-CaO-SiO2, whose kinetics of sintering by viscous flow and surface crystallization are known. The method of conformation with starches is innovative for glass-ceramics and its development opens the way for obtaining a new class of materials. We found a possible route for the production of porous compacts of glass particles, from the powder preparation to the removal of starch. It was observed that a glass powder obtained by dry milling in a ball mill with alumina balls for 24 h, afterwards mixed with water in an eccentric ball mill for 2 h, without the addition of a deflocculant, and subsequently mixed with starch also in an eccentric ball mill for 5 min resulted in slurries stable against sedimentation

Estudo do comportamento térmico e reológico de amidos na conformação cerâmica de compostos multicamada com alumina, titanato de alumínio e dióxido de titânio

The project aims to develop ceramic compounds with gradients of the mechanical properties, using the molding technique with commercial starches. To understand the process of interaction between starch and ceramic powders, the proposed methodology involves viscometry tests (up to 200 °C). Viscometric assays were carried out with slurries of alumina, titania and aluminum titanate with potato starch, cassava and corn. The specimens were tested for dilatometry, thermomechanical, thermal shock, mechanical and characterization by SEM. The ceramic powders and starches were analyzed using the optical microscope to measure the size of these. It was made of th kinetics of starch gelatinization and titania with the cornstarch in theoptical microscope to observe how the grains of starch behaved in welling

Efeitos dos parâmetros de usinagem no acabamento superficial de materiais cerâmicos a verde

Pós-graduação em Engenharia Mecânica - FEB

Corrosion prevention for Al2O3/SiC/C/MgAl2O4 based ceramics by means of impregnation with cerium-carrying solution

A cerium-carrying solution was developed so as to aprtially fill the open porosity of Al2O3/SiC/C/MgAl2O4 based refractory lining microstructure used in torpedo ladles, thereby enhancing wear resistance. The protection mchanism was cleared up and introduced from the impregnation technique using a cerium-carrying solution.

SnO2 dense ceramic microwave sintered with low resistivity

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Piezoresponse force microscopy behaviour of Bi4Ti3O12 ceramics with various excess bismuth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)