Rapid prototyping of polymeric electrophoresis microchips with integrated copper electrodes for contactless conductivity detection

A simple and easy approach to produce polymeric microchips with integrated copper electrodes for capacitively coupled contactless conductivity detection (CD) is described. Copper electrodes were fabricated using a printed circuit board (PCB) as an inexpensive thin-layer of metal. The electrode layout was first drawn and laser printed on a wax paper sheet. The toner layer deposited on the paper sheet was thermally transferred to the PCB surface working as a mask for wet chemical etching of the copper layer. After the etching step, the toner was removed with an acetonitrile-dampened cotton. A poly(ethylene terephthalate) (PET) film coated with a thin thermo-sensitive adhesive layer was used to laminate the PCB plate providing an insulator layer of the electrodes to perform CID measurements. Electrophoresis microchannels were fabricated in poly(dimethylsiloxane) (PDMS) by soft lithography and reversibly sealed against the PET film. These hybrid PDMS/PET chips exhibited a stable electroosmotic mobility of 4.25 +/- 0.04 x 10(-4) V cm(-2) s(-1), at pH 6.1, over fifty runs. Efficiencies ranging from 1127 to 1690 theoretical plates were obtained for inorganic cations.

Estimation of hexenuronic acids and kappa number in kraft pulps of Eucalyptus globulus by Fourier transform near infrared spectroscopy and multivariate analysis

Fourier transform near infrared (FT-NIR) spectroscopy was evaluated as an analytical too[ for monitoring residual Lignin, kappa number and hexenuronic acids (HexA) content in kraft pulps of Eucalyptus globulus. Sets of pulp samples were prepared under different cooking conditions to obtain a wide range of compound concentrations that were characterised by conventional wet chemistry analytical methods. The sample group was also analysed using FT-NIR spectroscopy in order to establish prediction models for the pulp characteristics. Several models were applied to correlate chemical composition in samples with the NIR spectral data by means of PCR or PLS algorithms. Calibration curves were built by using all the spectral data or selected regions. Best calibration models for the quantification of lignin, kappa and HexA were proposed presenting R-2 values of 0.99. Calibration models were used to predict pulp titers of 20 external samples in a validation set. The lignin concentration and kappa number in the range of 1.4-18% and 8-62, respectively, were predicted fairly accurately (standard error of prediction, SEP 1.1% for lignin and 2.9 for kappa). The HexA concentration (range of 5-71 mmol kg(-1) pulp) was more difficult to predict and the SEP was 7.0 mmol kg(-1) pulp in a model of HexA quantified by an ultraviolet (UV) technique and 6.1 mmol kg(-1) pulp in a model of HexA quantified by anion-exchange chromatography (AEC). Even in wet chemical procedures used for HexA determination, there is no good agreement between methods as demonstrated by the UV and AEC methods described in the present work. NIR spectroscopy did provide a rapid estimate of HexA content in kraft pulps prepared in routine cooking experiments.

Nanostructured diamond-like carbon films characterization

In this work, we have studied the influence of the substrate surface condition on the roughness and the structure of the nanostructured DLC films deposited by high-density plasma chemical vapor deposition Four methods were used to modify the silicon wafers surface before starting the deposition processes of the nanostructured DLC films. micro-diamond powder dispersion, micro-graphite powder dispersion, and roughness generation by wet chemical etching and roughness generation by plasma etching. The reference wafer was only submitted to a chemical cleaning. It was possible to see that the final roughness and the sp(3) hybridization degree (that is related with the structure and chemical composition) strongly depend on the substrate surface conditions The surface roughness was observed by AFM and SEM and the hybridization degree of the DLC films was analyzed by Raman Spectroscopy Thus, the effects of the substrate surface on the DLC film structure were confirmed. These phenomena can be explained by the fact that the locally higher surface energy and the sharp edges may induce local defects promoting the nanostructured characteristics in the DLC films. (C) 2009 Elsevier B.V. All rights reserved.

In Vitro Simultaneous Transfer of Lipids to HDL in Coronary Artery Disease and in Statin Treatment

The exchange of lipids with cells and other lipoproteins is a crucial process in HDL metabolism and for HDL antiatherogenic function. Here, we tested a practical method to quantify the simultaneous transfer to HDL of phospholipids, free-cholesterol, esterified cholesterol and triacylglycerols and to verify the lipid transfer in patients with coronary artery disease (CAD) or undergoing statin treatment. Twenty-eight control subjects without CAD, 27 with CAD and 25 CAD patients under simvastatin treatment were studied. Plasma samples were incubated with a donor nanoemulsion prepared by ultrasonication of the constituent lipids and labeled with radioactive lipids; % lipids transferred to HDL were quantified in the HDL-containing supernatant after chemical precipitation of non-HDL fractions and the nanoemulsion. The assay was precise and reproducible. Increase of temperature (4-37 A degrees C), of incubation period (5 min to 2 h), of HDL-cholesterol concentration (33-244 mg/dL) and of mass of nanoemulsion lipids (0.075-0.3 mg/mu L) resulted in increased lipid transfer from the nanoemulsion to HDL. In contrast, increasing pH (6.5-8.5) and albumin concentration (3.5-7.0 g/dL) did not affect lipid transfer. There was no difference between CAD and control non-CAD with regard to the lipid transfer, but statin treatment reduced the transfer to HDL of all four lipids. The test herein described is a valid and practical tool for exploring an important aspect of HDL metabolism.

Neoformation of micas in soils surrounding an alkaline-saline lake of Pantanal wetland, Brazil

The mineralogy and origin of micas were investigated in incipient soils surrounding a modem alkaline-saline lake of Nhecolandia, a sub-region of Pantanal wetland. Soils were sampled along a toposequence and analyzed by XRD, TEM-EDS, and ICP-MS. The studied micas, mainly concentrated in a green horizon, are dioctahedral, strongly associated with Fe(3+) and Al, and interstratified with smectite layers. Classification of individual crystals shows that glauconite and Fe-illite are the dominant micas, but one crystal of illite was recognized. Si-rich amorphous materials are associated with small crystallites in the mica-enriched horizon. A recent study shows that water samples from the studied lake and the surrounding water table have high pH, negative Eh, temperatures up to 40 C. high concentration of K. and low concentration of Si(OH)(4). Experimental studies of micas synthesis reported in the literature show that similar water conditions allow for dioctahedral mica crystallization from initial precipitation of amorphous hydroxides. Therefore, water characteristics combined with presence of Si-rich amorphous materials in the mica-enriched horizon suggest that the micas of the study area are neoformed. The alternated origin of illite, glauconite, and Fe-illite mixed-layer minerals probably occurs due to seasonal variations of pH. temperature, and chemical composition of waters in microenvironments, since the changes at this scale are possibly faster and more extreme. (C) 2010 Elsevier B.V. All rights reserved.

MINERALOGY AND GENESIS OF SMECTITES IN AN ALKALINE-SALINE ENVIRONMENT OF PANTANAL WETLAND, BRAZIL

Smectite formation in alkaline-saline environments has been attributed to direct precipitation from solution and/or transformation from precursor minerals, but these mechanisms are not universally agreed upon in the literature. The objective of this work was to investigate the mineralogy of smectites in the soils surrounding a representative alkaline-saline lake of Nhecolandia, a sub-region of the Pantanal wetland, Brazil, and then to identify the mechanisms of their formation. Soils were sampled along a toposequence and analyzed by X-ray diffraction, transmission electron microscopy-energy dispersive X-ray analysis, and inductively coupled plasma-mass spectrometry. Water was collected along a transect involving the studied toposequence and equilibrium diagrams were calculated using the databases PHREEQC and AQUA. The fine-clay fraction is dominated by smectite, mica, and kaolinite. Smectites are concentrated at two places in the toposequence: an upper zone, which includes the soil horizons rarely reached by the lake-level variation; and a lower zone, which includes the surface horizon within the area of seasonal lake-level variation. Within the upper zone, the smectite is dioctahedral, rich in Al and Fe, and is classified as ferribeidellite. This phase is interstratified with mica and vermiculite and has an Fe content similar to that of the mica identified. These characteristics suggest that the ferribeidellite originates from transformation of micas and that vermiculite is an intermediate phase in this transformation. Within the lower zone, smectites are dominantly trioctahedral, Mg-rich, and are saponitic and stevensitic minerals. In addition, samples enriched in these minerals have much smaller rare-earth element (REE) contents than other soil samples. The water chemistry shows a geochemical control of Mg and saturation with respect to Mg-smectites in the more saline waters. The REE contents, water chemistry, and the presence of Mg-smectite where maximum evaporation is expected, suggest that saponitic and stevensitic minerals originate by chemical precipitation from the water column of the alkaline-saline lake.

Metabolism of triglyceride-rich lipoproteins and lipid transfer to high-density lipoprotein in young obese and normal-weight patients with polycystic ovary syndrome

Objective: To clarify whether the metabolism of triglyceride-rich lipoproteins and lipid transfer to high-density lipoprotein (HDL) are altered in patients with polycystic ovary syndrome (PCOS). Design: Case control study. Setting: Endocrinology clinics. Patient(s): Eight normal-weight (NW) and 15 obese (013) patients with PCOS were compared with 10 NW and 10 Ob women without PCOS paired for age and body mass index. Intervention(s): Determination of triglyceride-rich lipoprotein metabolism and lipid transfer to HDL. Main Outcome Measure(s): Participants were injected triglyceride-rich emulsions labeled with (14)C-cholesteryl esters and (3)H-triglycerides and the fractional clearance rate (FCR, in min(-1)) of labels was determined. Lipid transfer from artificial nanoemulsions to HDL was performed by incubating radioactively labeled lipid nanoemulsions with plasma during 1 hour, followed by radioactive counting of HDL-containing supernatant after chemical precipitation. Result(s): Lipolysis estimated by triglyceride FCR was equal in PCOS groups (NW = 0.043 +/- 0.032, Ob = 0.033 +/- 0.009) and respective controls (NW = 0.039 +/- 0.015, Ob = 0.044 +/- 0.019). However, the remnant removal as estimated by cholesteryl ester FCR was reduced in both PCOS groups (NW = 0.005 +/- 0.006, Ob = 0.005 +/- 0.005) compared with controls (NW = 0.016 +/- 0.006, Ob = 0.011 +/- 0.072). Lipid transfer rates were not different among groups, but triglyceride transfer rates were positively correlated with homeostasis model assessment estimate of insulin resistance in PCOS. Conclusion(s): PCOS patients showed decreased removal of atherogenic remnants even when fasting glucose was <100 mg/dL. This reinforces the usefulness of the measures taken to prevent cardiovascular events in PCOS patients. (Fertil Steril (R) 2010;93:1948-56. (C)2010 by American Society for Reproductive Medicine.)

Electrospun Polyaniline-Reduced Graphene Oxide Composite Nanofibers Based High Sensitive Ammonia Gas Sensor

Ammonia is an important gas in many power plants and industrial processes so its detection is of extreme importance in environmental monitoring and process control due to its high toxicity. Ammonia’s threshold limit is 25 ppm and the exposure time limit is 8 h, however exposure to 35 ppm is only secure for 10 min. In this work a brief introduction to ammonia aspects are presented, like its physical and chemical properties, the dangers in its manipulation, its ways of production and its sources. The application areas in which ammonia gas detection is important and needed are also referred: environmental gas analysis (e.g. intense farming), automotive-, chemical- and medical industries. In order to monitor ammonia gas in these different areas there are some requirements that must be attended. These requirements determine the choice of sensor and, therefore, several types of sensors with different characteristics were developed, like metal oxides, surface acoustic wave-, catalytic-, and optical sensors, indirect gas analyzers, and conducting polymers. All the sensors types are described, but more attention will be given to polyaniline (PANI), particularly to its characteristics, syntheses, chemical doping processes, deposition methods, transduction modes, and its adhesion to inorganic materials. Besides this, short descriptions of PANI nanostructures, the use of electrospinning in the formation of nanofibers/microfibers, and graphene and its characteristics are included. The created sensor is an instrument that tries to achieve a goal of the medical community in the control of the breath’s ammonia levels being an easy and non-invasive method for diagnostic of kidney malfunction and/or gastric ulcers. For that the device should be capable to detect different levels of ammonia gas concentrations. So, in the present work an ammonia gas sensor was developed using a conductive polymer composite which was immobilized on a carbon transducer surface. The experiments were targeted to ammonia measurements at ppb level. Ammonia gas measurements were carried out in the concentration range from 1 ppb to 500 ppb. A commercial substrate was used; screen-printed carbon electrodes. After adequate surface pre-treatment of the substrate, its electrodes were covered by a nanofibrous polymeric composite. The conducting polyaniline doped with sulfuric acid (H2SO4) was blended with reduced graphene oxide (RGO) obtained by wet chemical synthesis. This composite formed the basis for the formation of nanofibers by electrospinning. Nanofibers will increase the sensitivity of the sensing material. The electrospun PANI-RGO fibers were placed on the substrate and then dried at ambient temperature. Amperometric measurements were performed at different ammonia gas concentrations (1 to 500 ppb). The I-V characteristics were registered and some interfering gases were studied (NO2, ethanol, and acetone). The gas samples were prepared in a custom setup and were diluted with dry nitrogen gas. Electrospun nanofibers of PANI-RGO composite demonstrated an enhancement in NH3 gas detection when comparing with only electrospun PANI nanofibers. Was visible higher range of resistance at concentrations from 1 to 500 ppb. It was also observed that the sensor had stable, reproducible and recoverable properties. Moreover, it had better response and recovery times. The new sensing material of the developed sensor demonstrated to be a good candidate for ammonia gas determination.

Model-based diagnosis system: application to constructed wetlands

Report for the scientific sojourn carried out at the Model-based Systems and Qualitative Reasoning Group (Technical University of Munich), from September until December 2005. Constructed wetlands (CWs), or modified natural wetlands, are used all over the world as wastewater treatment systems for small communities because they can provide high treatment efficiency with low energy consumption and low construction, operation and maintenance costs. Their treatment process is very complex because it includes physical, chemical and biological mechanisms like microorganism oxidation, microorganism reduction, filtration, sedimentation and chemical precipitation. Besides, these processes can be influenced by different factors. In order to guarantee the performance of CWs, an operation and maintenance program must be defined for each Wastewater Treatment Plant (WWTP). The main objective of this project is to provide a computer support to the definition of the most appropriate operation and maintenance protocols to guarantee the correct performance of CWs. To reach them, the definition of models which represent the knowledge about CW has been proposed: components involved in the sanitation process, relation among these units and processes to remove pollutants. Horizontal Subsurface Flow CWs are chosen as a case study and the filtration process is selected as first modelling-process application. However, the goal is to represent the process knowledge in such a way that it can be reused for other types of WWTP.

Bcl-xL is overexpressed in hormone-resistant prostate cancer and promotes survival of LNCaP cells via interaction with proapoptotic Bak.

Androgen-sensitive prostate cancer cells turn androgen resistant through complex mechanisms that involve dysregulation of apoptosis. We investigated the role of antiapoptotic Bcl-xL in the progression of prostate cancer as well as the interactions of Bcl-xL with proapoptotic Bax and Bak in androgen-dependent and -independent prostate cancer cells. Immunohistochemical analysis was used to study the expression of Bcl-xL in a series of 139 prostate carcinomas and its association with Gleason grade and time to hormone resistance. Expression of Bcl-xL was more abundant in prostate carcinomas of higher Gleason grades and significantly associated with the onset of hormone-refractory disease. In vivo interactions of Bcl-xL with Bax or Bak in untreated and camptothecin-treated LNCaP and PC3 cells were investigated by means of coimmunoprecipitation. In the absence of any stimuli, Bcl-xL interacts with Bax and Bak in androgen-independent PC3 cells but only with Bak in androgen-dependent LNCaP cells. Interactions of Bcl-xL with Bax and Bak were also evidenced in lysates from high-grade prostate cancer tissues. In LNCaP cells treated with camptothecin, an inhibitor of topoisomerase I, the interaction between Bcl-xL and Bak was absent after 36 h, Bcl-xL decreased gradually and Bak increased coincidentally with the progress of apoptosis. These results support a model in which Bcl-xL would exert an inhibitory effect over Bak via heterodimerization. We propose that these interactions may provide mechanisms for suppressing the activity of proapoptotic Bax and Bak in prostate cancer cells and that Bcl-xL expression contributes to androgen resistance and progression of prostate cancer.

Kalkkisaostuslaitteiston suunnittelu Biolan Oy:n lannoite- ja kasvualustatehtaan varastoja ja kompostointikentältä tulevien suoto- ja hulevesien käsittelyyn

Tässä diplomityössä oli tavoitteena löytää ratkaisu Biolan Oy:n lannoiteja kasvualustatehtaan varastoja kompostointikentältä tulevien suotoja hulevesien käsittelyyn. Erityisenä kiinnostuksen kohteena oli suotoja hulevesien sisältämän fosforin poistamisen ratkaisun löytäminen. Ratkaisua päätettiin lähteä hakemaan kemiallisen saostuksen kautta. Fosforin kemiallinen saostus toteutetaan nykypäivänä useimmiten raudan ja alumiini yhdisteiden avulla, mutta tämän työn lähtökohtana oli saostuksen suorittaminen kalkilla. Yhtenä työn lähtökohtana oli myös muodostuvan, fosforipitoisen, kalkkisakan hyödyntäminen Biolan Oy:n kasvualustatehtaan tuottamien kasvualustojen ravinnelähteenä, jolloin yleisesti ongelmana pidetty jätevesiliete muuttuu mahdollisuudeksi.

Flotaatio jätevedenpuhdistamon tertiäärivaiheena eräässä paperitehtaassa

Työn tavoitteena oli selvittää, kuinka tehokkaasti pystytään aktiivilieteprosessin läpikäynyttä, jälkiselkeytettyä vettä edelleen puhdistamaan flotaatiolla ennen sen johtamista vesistöön. Tarkoituksena oli löytää sellaiset kemikaalit ja näiden annokset, joilla tehtaalle asetetut jätevesien lupa-arvot voitaisiin huonossa tilanteessa, jätevesikuormitushuippujen aikana alittamaan. Työn kirjallisessaosassa tarkasteltiin lyhyesti, minkälaista jätevesikuormaa mekaanista massaa valmistavalta tehtaalta yleensä syntyy ja millaiset ovat tavanomaiset puhdistusmenetelmät. Myös flotaation teoriaa esiteltiin. Kokeellinen osa koostui kolmesta päävaiheesta: esi- eli niin sanotuista kuppikokeista, pilot-flotaatiokoeajoista jalaitosmittakaavan flotaatiokoeajoista. Esikokeet tehtiin niin kutsutulla Jar Test -laitteistolla ja pilot-flotaatiolaitteistona työssä käytettiin YIT:n valmistamaa pilot-flotaattoria. Laitosmittakaavan flotaatioaltaat olivat aikaisemmin biolietteen tiivistykseen käytettyjä, myöhemmin tertiääripuhdistukseen modifioituja flotaatioaltaita. Laitosmittakaavan flotaatiokoeajoissa testattiin neljän eri saostuskemikaalin ¿ polyalumiinikloridin (KEMPAC 18), rautapitoisen alumiinisulfaatin (AVR), ferrisulfaatin ja alumiinisulfaatin ¿ tehokkuutta tertiäärivaiheessa käsiteltävän veden puhdistajana. Esi- ja pilot-kokeiden perusteella laitosmittakaavan kokeisiin valittiin saostuskemikaalien rinnalle polymeeriksi Superfloc C 491. AVR- ja alumiinisulfaattiannokset laitosmittakaavan kokeissa olivat 200 ppm ja 400 ppm. KEMPAC 18- ja ferrisulfaattiannokset olivat 200ppm, 400 ppm ja 600 ppm. Polymeeriannos kokeissa oli pääasiassa 1,2 ppm. Tertiäärivaiheeseen tulevasta vedestä ja poistuvasta kirkasteesta määritettiin kiintoaine, pH, liukoinen ja kokonais-COD, liukoinen ja kokonaisfosfori sekä liukoinen ja kokonaistyppi. Laitosmittakaavan koeajojen tulosten mukaan eniten tertiäärivaiheessa saatiin käsiteltävästä vedestä erotettua fosforia ja toiseksi eniten COD:ta. Typpireduktiot olivat verrattain alhaiset ja myös kiintoainereduktiot jäivät usein pieniksi tai olivat jopa negatiiviset. Kaikki saostuskemikaalit saostivat COD- ja ravinnekuormaa. Eniten kuormaa saostuskemikaaleista saatiin erotettua AVR:llä ja toiseksi eniten KEMPAC 18:lla. Laitteistojen käyttökustannuksia huomioimatta AVR olisi edullisin vaihtoehto saostuskemikaaaliksietenkin pidempiaikaisessa käytössä. Lisäksi työssä tutkittiin polymeeriannoksen kasvattamisen 1,2 ppm:stä 2,5 ppm:ään vaikutusta puhdistustulokseen, kun saostuskemikaaliannos pidettiin vakiona. Tulosten mukaan polymeeriannoksen kasvattaminen kasvatti kokonais-COD- ja kokonaisfosforireduktiota. Myöslaitosmittakaavan flotaatioaltaiden pohjaputkistoja vertailtiin kiintoainereduktioiden perusteella. Kokeissa saatujen tulosten mukaan ei voitu sanoa, oliko toisen altaan pitkä kirkasteenpoistoputki vai toisen altaan lyhyt kirkasteenpoistoputki parempi vaihtoehto.

Localization and fine structure of a vaccinia virus gene encoding an envelope antigen.

The major antigen on the envelope of extracellular vaccinia virus particles is a polypeptide with an apparent molecular weight of 37,000 (p37K; G. Hiller and K. Weber, J. Virol. 55:651-659, 1985). The gene encoding p37K was mapped in the vaccinia virus genome by hybrid selection of RNA followed by in vitro translation. p37K was then identified among the in vitro translation products by immunoprecipitation with a monoclonal antibody. The gene is located close to the right-hand end of the HindIII F fragment. The corresponding region of the DNA was sequenced, and an open reading frame encoding a polypeptide of 41,748 daltons was observed. The 5' end of the mRNA, as defined by nuclease S1 analysis, maps within only a few nucleotides of the translation initiation codon. Examination of the DNA sequence around the putative initiation site of transcription revealed a characteristic sequence, TAAATG, which includes the ATG translation initiation codon and which is conserved in all but one late gene so far analyzed. It is therefore likely that this sequence is an important regulatory signal for late gene expression in vaccinia virus.

Sellun kuivauskoneen ajettavuusongelman monimuuttujainen tarkastelu

Tässä työssä on tutkittu sellun kuivauskoneella koivusellua kuivattaessa esiintyvää ajettavuusongelmaa. Tähän ongelmaan on etsitty ratkaisua monimuuttujamenetelmien avulla. Työn kirjallisuusosassa on lyhyesti käyty läpi sellun kuivauskoneiden historia lieriöviirakoneista nykyaikaisiin kaksoisviirasovelluksiin. Lisäksi kirjallisuusosassa on käsitelty tässä työssä käytettyjen monimuuttujamenetelmien perusteet ja käyty esimerkin omaisesti läpi joitakin kemometrian sovelluksia puunjalostusteollisuudessa. Työn kokeellisessa osassa on haettu tiedonkeruujärjestelmästä massan ominaisuuksista ja kuivauskoneen ajoparametreistä koostuvaa dataa vuoden 1999 ajalta. Tästä datasta on tehty PCA-mallit vuoden 1999 jokaisen kuukauden datasta ja diskriminoiva PLS-malli ajettavuuden kannalta hyvästä ja huonosta jaksosta koostuvasta datasta. Kuivauskoneelta on koottu dataa myös ottamalla kiertovesi- ja selluarkkinäytteitä. Kiertovesinäytteiden analyysituloksista on tehty PCA-mallit ja lisäksi analyysitulokset on tarkasteltu yksimuuttujaisesti. Selluarkkinäytteistä on määritetty UV-spektrit ja niistä on tehty PCA-mallit, jotta spektreistä saataisiin mahdollisimman paljon informaatiota. Työssä on havaittu yhdeksi selitykseksi ajettavuusongelmalle kuivauskoneen kiertovesien likaantuminen. Kiertovesiä ja massarainan pintakemiaa tulisi kuitenkin tutkia laajemmassa mittakaavassa kuin tämän työn puitteissa on ollut mahdollista tutkia.

Jätevedenpuhdistamon toiminnan optimointi

Schauman Wood Oy Pelloksen tehtaat on Euroopan suurin havuvanerin valmistaja. Tehtailla tukkien haudonnassa ja kuorien kuivaamisessa syntyvät jätevedet sekä sosiaalijätevedet puhdistetaan omassa biologisessa puhdistamossa. Puhdistamo rakennettiin alun perin aktiivilietelaitokseksi ja muutettiin kuormituksen kasvaessa vuonna 2002 kantoaineprosessiksi. Puhdistamolle laskettiin ensin optimaalinen kuormitus, jonka perusteella kuormitusta ryhdyttiin nostamaan. Tavoitteena oli saavuttaa virtaaman nostolla ja ajomallien muutoksilla tilavuuskuorma 1-3 kgBOD/m3•d. Kun tulovirtaamaa oli saatu nostettua riittävästi, tehtiin laskeutuskokeita laskeutuskemikaalin optimimäärän selvittämiseksi. Koeajojakson lopuksi pidettiin kolmen viikon tehotarkkailujakso, jolloin kokeiltiin puhdistamon ajoa erilaisilla kemikaalimäärillä. Näin saatiin selville tasemielessä tietyn puumäärän aiheuttama kuormitus puhdistamolle. Jätevedenpuhdistamon tulovirtaama saatiin nostettua tasolle 300- 350 m³/d, jolloin tilaavuuskuormaksi tuli 1,68 kgBOD/m3•d. Kolmen viikon tehotarkkailujakson aikana saatiin selvitettyä optimikemikaaliannostus sekä laskettua kolmesta eri vaihtoehdosta taloudellisesti kannattavin ajomalli. Puhdistusreduktioiden, puhdistamon toimivuuden ja taloudellisuuden kannalta paras vaihtoehto oli laskeutuskemikaalin ja polymeerin yhteiskäyttö.