Mechanical properties of sheet metal under forming conditions

In the bulge test, a sheet metal specimen is clamped over a circular hole in a die and formed into a bulge by the hydraulic pressure on one side of the specirnen. As the unsupported part of the specimen is deformed in this way, its area is increased, in other words, the material is generally stretched and its thickness generally decreased. The stresses causing this stretching action are the membrane stresses in the shell generated by the hydraulic pressure, in the same way as the rubber in a toy balloon is stretched by the membrane stresses caused by the air inside it. The bulge test is a widely used sheet metal test, to determine the "formability" of sheet materials. Research on this forming process (2)-(15)* has hitherto been almost exclusively confined to predicting the behaviour of the bulged specimen through the constitutive equations (stresses and strains in relation to displacements and shapes) and empirical work hardening characteristics of the material as determined in the tension test. In the present study the approach is reversed; the stresses and strains in the specimen are measured and determined from the geometry of the deformed shell. Thus, the bulge test can be used for determining the stress-strain relationship in the material under actual conditions in sheet metal forming processes. When sheet materials are formed by fluid pressure, the work-piece assumes an approximately spherical shape, The exact nature and magnitude of the deviation from the perfect sphere can be defined and measured by an index called prolateness. The distribution of prolateness throughout the workpiece at any particular stage of the forming process is of fundamental significance, because it determines the variation of the stress ratio on which the mode of deformation depends. It is found. that, before the process becomes unstable in sheet metal, the workpiece is exactly spherical only at the pole and at an annular ring. Between the pole and this annular ring the workpiece is more pointed than a sphere, and outside this ring, it is flatter than a sphere. In the forming of sheet materials, the stresses and hence the incremental strains, are closely related to the curvatures of the workpiece. This relationship between geometry and state of stress can be formulated quantitatively through prolateness. The determination of the magnitudes of prolateness, however, requires special techniques. The success of the experimental work is due to the technique of measuring the profile inclination of the meridional section very accurately. A travelling microscope, workshop protractor and surface plate are used for measurements of circumferential and meridional tangential strains. The curvatures can be calculated from geometry. If, however, the shape of the workpiece is expressed in terms of the current radial (r) and axial ( L) coordinates, it is very difficult to calculate the curvatures within an adequate degree of accuracy, owing to the double differentiation involved. In this project, a first differentiation is, in effect, by-passed by measuring the profile inclination directly and the second differentiation is performed in a round-about way, as explained in later chapters. The variations of the stresses in the workpiece thus observed have not, to the knowledge of the author, been reported experimentally. The static strength of shells to withstand fluid pressure and their buckling strength under concentrated loads, both depend on the distribution of the thickness. Thickness distribution can be controlled to a limited extent by changing the work hardening characteristics of the work material and by imposing constraints. A technique is provided in this thesis for determining accurately the stress distribution, on which the strains associated with thinning depend. Whether a problem of controlled thickness distribution is tackled by theory, or by experiments, or by both combined, the analysis in this thesis supplies the theoretical framework and some useful experimental techniques for the research applied to particular problems. The improvement of formability by allowing draw-in can also be analysed with the same theoretical and experimental techniques. Results on stress-strain relationships are usually represented by single stress-strain curves plotted either between one stress and one strain (as in the tension or compression tests) or between the effective stress and effective strain, as in tests on tubular specimens under combined tension, torsion and internal pressure. In this study, the triaxial stresses and strains are plotted simultaneously in triangular coordinates. Thus, both stress and strain are represented by vectors and the relationship between them by the relationship between two vector functions. From the results so obtained, conclusions are drawn on both the behaviour and the properties of the material in the bulge test. The stress ratios are generally equal to the strain-rate ratios (stress vectors collinear with incremental strain vectors) and the work-hardening characteristics, which apply only to the particular strain paths are deduced. Plastic instability of the material is generally considered to have been reached when the oil pressure has attained its maximum value so that further deformation occurs under a constant or lower pressure. It is found that the instability regime of deformation has already occurred long before the maximum pressure is attained. Thus, a new concept of instability is proposed, and for this criterion, instability can occur for any type of pressure growth curves.

An analysis of the effect of process parameters on the formability of sheet metal

This investigation is in two parts, theory and experimental verification. (1) Theoretical Study In this study it is, for obvious reasons, necessary to analyse the concept of formability first. For the purpose of the present investigation it is sufficient to define the four aspects of formability as follows: (a) the formability of the material at a critical section, (b) the formability of the material in general, (c) process efficiency, (d) proportional increase in surface area. A method of quantitative assessment is proposed for each of the four aspects of formability. The theoretical study also includes the distinction between coaxial and non-coaxial strains which occur, respectively, in axisymmetrical and unsymmetrical forming processes and the inadequacy of the circular grid system for the assessment of formability is explained in the light of this distinction. (2) Experimental Study As one of the bases of the experimental work, the determination of the end point of a forming process, which sets the limit to the formability of the work material, is discussed. The effects of three process parameters on draw-in are shown graphically. Then the delay of fracture in sheet metal forming resulting from draw-in is analysed in kinematical terms, namely, through the radial displacements, the radial and the circumferential strains, and the projected thickness of the workpiece. Through the equilibrium equation of the membrane stresses, the effect on the shape of the unsupported region of the workpiece, and hence the position of the critical section is explained. Then, the effect of draw-in on the four aspects of formability is discussed throughout this investigation. The triangular coordinate system is used to present and analyse the triaxial strains involved. This coordinate system has the advantage of showing all the three principal strains in a material simultaneously, as well as representing clearly the many types of strains involved in sheet metal work.

Ohutlevyjen laserhitsaus

Tässä diplomityössä tarkasteltiin laseria ja sen käyttöä laserhitsauksessa. Laserin käyttäminen asettaa omat vaatimuksensa ja haasteet laserhitsattavan tuotteen ja mahdollisen kiinnittimen suunnittelulle. Lisäksi laserin käyttö konepajassa asettaa tiettyjä vaatimuksia työympäristölle. Diplomityössä suunniteltiin uudelleen eräs ohutlevystä valmistettava kotelo ja pyrittiin selvittämään soveltuuko se laserhitsattavaksi, ja saako kotelosta hitsattua täysin tiiviin. Kotelo soveltui hyvin laserhitsattavaksi, mutta täysin tiiviin kotelon hitsaaminen oli haasteellista ja hyvin epävarmaa.

Design and application of experimental methods for steel sheet shearing

Shearing is the process where sheet metal is mechanically cut between two tools. Various shearing technologies are commonly used in the sheet metal industry, for example, in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material. The constant development of sheet metals toward higher strength and formability leads to increased forces on the shearing equipment and tools. Shearing of new sheet materials imply new suitable shearing parameters. Investigations of the shearing parameters through live tests in the production are expensive and separate experiments are time consuming and requires specialized equipment. Studies involving a large number of parameters and coupled effects are therefore preferably performed by finite element based simulations. Accurate experimental data is still a prerequisite to validate such simulations. There is, however, a shortage of accurate experimental data to validate such simulations. In industrial shearing processes, measured forces are always larger than the actual forces acting on the sheet, due to friction losses. Shearing also generates a force that attempts to separate the two tools with changed shearing conditions through increased clearance between the tools as result. Tool clearance is also the most common shearing parameter to adjust, depending on material grade and sheet thickness, to moderate the required force and to control the final sheared edge geometry. In this work, an experimental procedure that provides a stable tool clearance together with accurate measurements of tool forces and tool displacements, was designed, built and evaluated. Important shearing parameters and demands on the experimental set-up were identified in a sensitivity analysis performed with finite element simulations under the assumption of plane strain. With respect to large tool clearance stability and accurate force measurements, a symmetric experiment with two simultaneous shears and internal balancing of forces attempting to separate the tools was constructed. Steel sheets of different strength levels were sheared using the above mentioned experimental set-up, with various tool clearances, sheet clamping and rake angles. Results showed that tool penetration before fracture decreased with increased material strength. When one side of the sheet was left unclamped and free to move, the required shearing force decreased but instead the force attempting to separate the two tools increased. Further, the maximum shearing force decreased and the rollover increased with increased tool clearance. Digital image correlation was applied to measure strains on the sheet surface. The obtained strain fields, together with a material model, were used to compute the stress state in the sheet. A comparison, up to crack initiation, of these experimental results with corresponding results from finite element simulations in three dimensions and at a plane strain approximation showed that effective strains on the surface are representative also for the bulk material. A simple model was successfully applied to calculate the tool forces in shearing with angled tools from forces measured with parallel tools. These results suggest that, with respect to tool forces, a plane strain approximation is valid also at angled tools, at least for small rake angles. In general terms, this study provide a stable symmetric experimental set-up with internal balancing of lateral forces, for accurate measurements of tool forces, tool displacements, and sheet deformations, to study the effects of important shearing parameters. The results give further insight to the strain and stress conditions at crack initiation during shearing, and can also be used to validate models of the shearing process.

Blade design and forming for fans using finite elements

The necessity of adapting the standardized fan models to conditions of higher temperature has emerged due to the growth of concerning referring to the consequences of the gas expelling after the Mont Blanc tunnel accident in Italy and France, where even though, with 100 fans in operation, 41 people died. However, since then, the defied solutions have pointed to aerodynamic disadvantages or have seemed nonappropriate in these conditions. The objective of this work is to present an alternative to the market standard fans considering a new technology in constructing blades. This new technology introduces the use of the stainless steel AISI 409 due to its good adaptation to temperatures higher than 400°C, particularly exposed to temperatures of gas exhaust from tunnels in fire situation. Furthermore, it presents a very good resistance to corrosion and posterior welding and pressing, due to its alloyed elements. The innovation is centered in the process of a deep drawing of metallic shells and posterior welding, in order to keep the ideal aerodynamic superficies for the fan ideal performance. On the other hand, the finite element method, through the elasto-plastic software COSMOS permitted the verification of the thickness and structural stability of the blade in relation to the aerodynamic efforts established in the project. In addition, it is not advisable the fabrication of blades with variable localized thickness not even, non-uniform ones, due to the verified concentration of tensions and the difficulties observed in the forming. In this way, this study recommends the construction of blades with uniform variations of thickness. © 2007 Springer.

Computer aided form roll design

Cold roll forming is an extremely important but little studied sheet metal forming process. In this thesis, the process of cold roll forming is introduced and it is seen that form roll design is central to the cold roll forming process. The conventional design and manufacture of form rolls is discussed and it is observed that surrounding the design process are a number of activities which although peripheral are time consuming and a possible source of error. A CAD/CAM system is described which alleviates many of the problems traditional to form roll design. New techniques for the calculation of strip length and controlling the means of forming bends are detailed. The CAD/CAM system's advantages and limitations are discussed and, whilst the system has numerous significant advantages, its principal limitation can be said to be the need to manufacture form rolls and test them on a mill before a design can be stated satisfactory. A survey of the previous theoretical and experimental analysis of cold roll forming is presented and is found to be limited. By considering the previous work, a method of numerical analysis of the cold roll forming process is proposed based on a minimum energy approach. Parallel to the numerical analysis, a comprehensive range of software has been developed to enhance the designer's visualisation of the effects of his form roll design. A complementary approach to the analysis of form roll design is the generation of form roll design, a method for the partial generation of designs is described. It is suggested that the two approaches should continue in parallel and that the limitation of each approach is knowledge of the cold roll forming process. Hence, an initial experimental investigation of the rolling of channel sections is described. Finally, areas of potential future work are discussed.

Computer aided design and manufacture of form-rolls

Cold roll forming of thin-walled sections is a very useful process in the sheet metal industry. However, the conventional method for the design and manufacture of form-rolls, the special tooling used in the cold roll forming process, is a very time consuming and skill demanding exercise. This thesis describes the establishment of a stand-alone minicomputer based CAD/CAM system for assisting the design and manufacture of form-rolls. The work was undertaken in collaboration with a leading manufacturer of thin-walled sections. A package of computer programs have been developed to provide computer aids for every aspect of work in form-roll design and manufacture. The programs have been successfully implemented, as an integrated CAD/CAM software system, on the ICL PERQ minicomputer with graphics facilities. Thus, the developed CAD/CAM system is a single-user workstation, with software facilities to help the user to perform the conventional roll design activities including the design of the finished section, the flower pattern, and the form-rolls. A roll editor program can then be used to modify, if required, the computer generated roll profiles. As far as manufacturing is concerned, a special-purpose roll machining program and postprocessor can be used in conjunction to generate the NC control part-programs for the production of form-rolls by NC turning. Graphics facilities have been incorporated into the CAD/CAM software programs to display drawings interactively on the computer screen throughout all stages of execution of the CAD/CAM software. It has been found that computerisation can shorten the lead time in all activities dealing with the design and manufacture of form-rolls, and small or medium size manufacturing companies can gain benefits from the CAD/CM! technology by developing, according to its own specification, a tailor-made CAD/CAM software system on a low cost minicomputer.

Levantamento, reparação e beneficiação do simulador TERCO PST 2200 do Laboratório de Sistemas de Energia do ISEP

Este trabalho é baseado no simulador de redes PST2200 do Laboratório de Sistemas de Energia (LSE) pois está avariado com vários problemas conhecidos, designadamente: - Defeito de isolamento (disparo de diferencial), - Desregulação da velocidade da máquina primária (motor DC), - Circuito de excitação da máquina síncrona inoperacional, - Inexistência de esquemas elétricos dos circuitos do simulador, - Medidas desreguladas e com canais de medida com circuito impresso queimado. O trabalho executado foi: - O levantamento e desenho de raiz (não existe qualquer manual) dos esquemas dos 10 módulos do simulador, designadamente naqueles com avaria ou com desempenho problemático a fim de que se possa ter uma visão mais pormenorizada dos circuitos e seus problemas, por forma a intervir para os minimizar e resolver, - Foi realizado o diagnóstico de avaria do simulador e foram propostas soluções para os mesmos, - Realizaram-se as intervenções propostas e aprovadas. Nas intervenções realizadas, os princípios orientadores foram: - Aumentar a robustez do equipamento por forma a garantir a sua integridade a utilizações menos apropriados e manobras 'exóticas' próprias de alunos, que pela sua condição, estão em fase de aprendizagem, - Atualizar o equipamento, colocando-o em sintonia com o 'estado da arte', - Como fator de valorização suplementar, foi concebida e aplicada a supervisão remota do funcionamento do simulador através da rede informática. Foram detetados inúmeros erros: - Má ligação do motor de corrente continua ao variador, resultando a falta de controlo da frequência da rede do sistema, - Ligações entre painéis trocadas resultando em avarias diversas das fontes de alimentação, - Cartas eletrónicas de medidas avariadas e que além de se reparar, foram também calibradas. Devido ao mecenato da empresa Schnitt + Sohn participando monetariamente, fez-se o projeto de alteração e respetiva execução de grande parte do simulador aumentando a fiabilidade do mesmo, diminuindo assim a frequência das avarias naturais mais as que acontecem involuntariamente devido a este ser um instrumento didático. Além do trabalho elétrico, foi feito muito trabalho de chaparia para alteração de estrutura e suporte do material com diferenças de posicionamento. Neste trabalho dá-se também alguns exemplos de cálculo e simulação das redes de transporte que se pode efetuar no simulador como estudo e simulação de avarias num sistema produtivo real. Realizou-se a monitorização de dois aparelhos indicadores de parâmetros de energia (Janitza UMG96S) através duma rede com dois protocolos ethernet e profibus utilizando o plc (Omron CJ2M) como valorização do trabalho.

Estudo de Ferramentas FEA Comerciais na Simulação Numérica de Processos de Conformação de Chapas Metálicas. Aplicação à Indústria Automóvel.

Os componentes obtidos através da conformação plástica de chapas têm uma grande importância, tanto na etapa de concepção do produto como na etapa de produção na indústria automóvel. Isto comprova-se pelo facto de, em média, cada automóvel integrar cerca de 500 componentes estampados para construir o chassis e a carroçaria [Alves 2003]. Deste total de componentes, 50 são de grandes dimensões (portas, tejadilho, painéis inferior e laterais, entre outros) e necessitam, em média, de cinco ferramentas para o seu fabrico, sendo o custo estimado para cada ferramenta de 230 000 € [Col 2000, Alves 2003]. Para além da indústria automóvel, a conformação plástica de chapas metálicas é um processo tecnológico presente nas indústrias relativas à aeroespacial, petrolífera, decoração, alimentar, entre outras. Do ponto de vista do enquadramento económico, cerca de 20% do custo total de um automóvel novo é devido à incorporação de componentes metálicos estampados. [Alves 2003]. A pressão do “Mercado Global” faz com que os custos relativos à matéria-prima, energia e mão-de-obra sejam uma constante em termos de redução do seu impacte no orçamento das empresas fornecedoras destes produtos. É neste contexto que surge a necessidade da realização deste estudo de Benchmark de Softwares, tornando-se bastante importante, quer ao nível da competitividade industrial, quer ao nível da inovação para novos produtos. A análise por elementos finitos desempenha um papel primordial no tryout virtual e otimização das ferramentas e processos de conformação plástica. Os objetivos principais deste estudo de simulação numérica são a identificação e comparação dos resultados obtidos pelo AUTOFORM e pelo PAMSTAMP, para cada uma das variáveis identificadas como as mais influentes na robustez dos processos de estampagem de chapa metálica. Estas variáveis identificadas são: consumo de material (Draw-in) após conformação; forças de conformação; valores de variação de espessura e dos valores de extensão e resultados de Springback. Os resultados obtidos são comparados com os resultados experimentais e, desta forma, avalia-se a capacidade inovadora e a eficácia de cada um dos softwares, obtendo-se assim, uma orientação mais real para o software mais indicado aos objetivos impostos pela indústria automóvel. Para este efeito, a indústria automóvel, como maior impulsionador e motor da investigação na área da simulação numérica aplicada aos processos de estampagem, tem aderido em peso ao Benchmarking. Um exemplo disto, é o que acontece nas conferências Numisheet. O Benchmark #2 da conferência Numisheet 2008 é analisado pormenorizadamente e os resultados numéricos e experimentais são comparados e apresentados. Dois materiais distintos (aço HC260LAD e liga de alumínio AC170), assim como três modelos com geometrias diferentes (com e sem freios) são apresentados neste relatório. Com vista à redução dos ciclos tentativa-erro, tem-se adotado ciclos virtuais ou numéricos e tem-se incrementado a interatividade entre as fases de concepção e projeto, num conceito muito próprio, mas cada vez mais abrangente, denominado “produção virtual”. É nesta filosofia que se insere a simulação numérica dos processos de conformação de chapa.

Designing next generation car washing machines with rotary brushes

Tese de Doutoramento - Leaders for Technical Industries (LTI) - MIT Portugal

Disseny dels elements constitutius per adaptar un centre de mecanitzat de control numèric a la tecnologia Incremental Sheet Forming (ISF)

Un dels processos tradicionals de conformació de xapa més utilitzats a nivell industrial, degut a la seva rapidesa d’operació i la seva maduresa del procés, és l’embotició. Per a dur a terme aquest procés és necessària la construcció d’uns utillatges (matriu i punxó) per a cada tipus de producte. Aquests utillatges estan fabricats amb materials altament resistents ja que han de poder suportar càrregues molt importants durant la deformació. A més, s’han de garantir unes precisions dimensionals molt bones per tal d’evitar el xoc entre les dues parts de l’utillatge i per a assegurar que la peça obtinguda tingui les dimensions desitjades. Aquest fet implica que el procés d’obtenció de les matrius i punxons tingui un cost molt elevat i per a amortitzar-lo és necessari que la producció sigui en massa.L’objecte d’aquest projecte és adaptar el centre de mecanitzat Kondia HS1000 per tal de poder dur a terme recerca bàsica de la tecnologia de conformat incremental de xapa (ISF) en el Grup de Recerca en Enginyeria del Producte, Procés i Producció (GREP)

Disseny d'una màquina carregadora de planxa a l'empresa Serralleria i Alumini Vilaró (S.A.V)

Les empreses sempre han buscat com optimitzar el màxim els seus recursos i ser més eficients a la hora de realitzar les tasques que li han estat encomanades. És per aquest motiu que constantment les empreses realitzen estudis i valoracions de com poder millorar dia a dia. Aquest fet no és diferenciador a l’empresa Serralleria i Alumini Vilaró (S.A.V), que dia a dia estudia com optimitzar els seus processos o de vegades introduir-ne de nous per tal d’expandir la seva oferta de serveis. L’empresa és dedica a la fabricació de peces metàl•liques el procés ja sigui només de tall i mecanitzat, plegat, soldadura, acabats en inoxidable, pintura i fins i tot embalatge pel que fa a la part productiva, respecte a la part d’oficina tècnica també ofereix serveis de desenvolupament de productes segons especificacions del client i reenginyeria de qualsevol producte, analitzant la part que és vol millorar. En l’actualitat l’empresa ha detectat una mancança que creu que es podria solucionar, el problema és que l’empresa disposa de varies màquines de tall, entre les quals hi ha una màquina de tall làser i el problema principal és que la càrrega de les planxes del calaix de magatzem a la bancada de la màquina es realitza o bé manualment o a través d’un gripper sostingut al pont grua, depenent del pes de la planxa a transportar. L’objectiu principal d’aquest treball és fer el disseny d’una màquina que permeti automatitzar el procés de transportar la planxa metàl•lica del calaix de magatzem dipositat sobre una taula mòbil a la bancada de la màquina de tall. El disseny que pretenem fer és complet començant per fer un disseny estructural de la màquina més els seus respectius càlculs, moviments que volem aconseguir, tria de components ( motors, sensors ...), elaboració d’un pressupost per poder fer una estimació i finalment la elaboració del programa de control de tota la màquina més la interacció amb la màquina a través d’una pantalla tàctil. Es a dir, el que pretenem és realitzar un projecte que puguem fabricar en la realitat utilitzant tota la informació continguda dins del mateix

Ohutlevytuotteenvalmistusteknisten piirteiden tunnistaminen ja käyttö suunnittelun apuna

Suunnittelu- ja valmistustoiminnot ovat eriytymässä myös ohutlevyteollisuudessa. Kilpailukyvyn parantamiseksi, valmistusta siirretään alihankkijoille maihin, jossa työvoima on halpaa ja suuret markkinat lähellä, tuotekehityksen ja suunnittelun jäädessä Suomeen tai muualle Länsi-Eurooppaan. Tällöin vanhan lokaalin toimintamallin synergiaedut eivät ole enää mahdollisia ja tuotteen valmistettavuuden arviointi, laadunhallinta ja komponenttien yhteensopivuuden varmistaminen on erittäin haasteellista. Tässä tutkimuksessa etsittiin uuden toimintamallin tuomiin haasteisiin vastauksia piirrepohjaisesta mallintamisesta. Tavoitteen mukaisesti, tutkimuksessa tunnistettiin ohutlevytuotteen valmistusteknilliset piirteet ja luotiin niiden mukainen piirrekaavio. Piirteiden tunnistus vaati tutkimustyötä sekä nykyaikaisten suunnittelumetodien että valmistusmenetelmien ja ohutlevymateriaalien parissa. Lisäksitarkasteltiin, millaisia vaikutuksia piirteillä on tuotteen valmistettavuuteen ja miten nämä tulee huomioida tuotteen suunnittelussa.

Joustavan robotisoidun särmäyssolun käyttöönotto levytuotetahtaalla

Diplomityön ensimmäisenä tavoitteena on selvittää robotisoidun särmäyssolun tehokkaimmat käyttöalueet särmättävien kappaleiden muotojen ja laitteiston teknisten edellytysten perusteella. Toisena tavoitteena on tuoda esille robotisoidun särmäyssolun käyttöönottoon liittyviä ongelmia ja antaa käytännön ohjeita niiden ratkaisemiseksi. Tuloksia sovelletaan jatkossa kohdeyrityksen markkinoiman särmäyssolun tuotekehitykseen. Särmäyksen automatisoinnin pääpiirteitä tarkastellaan tutkimalla markkinoilla olevien robottisolujen toimintaperiaatteita ja ohjelmointitapoja. Työssä on myös esitetty kohdeyrityksen omat tavoitteet ja lähtökohdat särmäysmenetelmien kehittämiseen, joista tärkeimmät ovat integroitavuus joustavaan valmistusjärjestelmään ja solun kehittäminen myyntiartikkeliksi. Työssä esitellään robotisoidun särmäyssolun toimintaa kuvaamalla työkierron toiminnot pääpiirteissään. Samassa yhteydessä esitellään myös solun konekanta sekä koneiden välillä tapahtuva tiedon siirto. Erityisenä mielenkiinnon kohteena ovat olleet joustavan valmistusjärjestelmän soluohjaimen toiminnot ja särmäyssolun toimivuus FMS:n osana. Analyyttisessä osuudessa tutkitaan kappaleiden särmättävyyttä robotisoidussa tuotantoratkaisussa. Lähtökohdaksi on otettu särmäyspuristimen, robotin, lisälaitteiden ja kappaleen muotojen asettamat rajoitukset sekä toisaalta robotisoinnin tuomat uudet mahdollisuudet. Tulosten perusteella robotisointi soveltuu parhaiten painaville tai monimutkaisille kappaleille, joiden manuaalisärmäys vie paljon aikaa. Taloudellisia käyttöalueita kartoitettiin tutkimalla eräkokoon, ohjelmointiajan, kappaleajan ja särmien määrän vaikutusta valmistuskustannuksiin. Robotisoinnin on todettu kannattavan yrityksissä, joissa sarjat ovat usein toistuvia ja eräkoot yli 150 kappaleen suuruisia. Kappaleen muoto ja särmien määrä vaikuttaa monin tavoin kappaleaikaan ja siten myös valmistuskustannuksiin. Robotisoinnin kannattavuutta on näissä tapauksissa arvioitava aina tapauskohtaisesti työkierron vaatimien toimintojen perusteella.

Raideliikenteen opastimien valoyksiköiden koteloiden tuotekehitys

Nykyisin raideliikenteen käytössä olevan opastinjärjestelmän mukaiset opastimet ovat kunnossapidollisesti erittäin haastavia. Niiden korkeus aiheuttaa kunnossapitohenkilöstölle työturvallisuusriskin ja monimutkaiset opastinulokkeet ja - portaalit ovat kalliita rakentaa. Nykyisin käytössä oleva opastinjärjestelmä onkin tarkoitus korvata Opastinjärjestelmä 2010 -nimisellä järjestelmällä, jonka kehitystyö on aloitettu Ratahallintokeskuksessa vuonna 2006. Tämä diplomityö on osa kyseistä kehitystyötä. Työn tarkoituksena on raideliikenteen käyttöön tulevien Opastinjärjestelmä 2010:n mukaisten opastimien valoyksiköiden koteloiden rakenteen suunnittelu ja materiaalinvalinta. Suunnittelutyöhön sisältyvät myös valoyksiköiden häikäisysuojien suunnittelu, sekä opastimien koteloiden liittäminen opastimien jalkoihin. Uusille opastimille suunnitellaan myös putkipaaluperustus. Opastinjärjestelmä 2010:n mukaisten opastimien myötä opastinten sijoittelua voidaan parantaa, ja niiden kunnossapito helpottuu. Uuden järjestelmän opastimien kotelot tarjoavat opastimien valoyksiköille entistä avointa levyrakennetta paremman ilkivaltasuojan. Uusissa opastimissa otetaan käyttöön LED-valoyksiköt, joka vähentää kunnossapitokustannuksia lamppujen vaihtotarpeen pienentyessä.