Rapid computation of static fields produced by thick circular solenoids

A straightforward method is proposed for computing the magnetic field produced by a circular coil that contains a large number of turns wound onto a solenoid of rectangular cross section. The coil is thus approximated by a circular ring containing a continuous constant current density, which is very close to the real situation when sire of rectangular cross section is used. All that is required is to evaluate two functions, which are defined as integrals of periodic quantities; this is done accurately and efficiently using trapezoidal-rule quadrature. The solution can be obtained so rapidly that this procedure is ideally suited for use in stochastic optimization, An example is given, in which this approach is combined with a simulated annealing routine to optimize shielded profile coils for NMR.

Estudo numérico sobre o reforço de pilares de betão armado com cantoneiras e presilhas metálicas: análise paramétrica e modelo de cálculo

Dissertação de mestrado integrado em Engenharia Civil

Innenhochdruckabschneiden mit Schneidring von Hohlprofilen

Separating, cutting, hydroforming, hydrocutting, cutting groove, cutting ring, t-piece, tube, hollow section

Materiaalimallin määrityksestä kylmämuovattujen putkipalkkien K-liitosten FE-analyysissä

Työssä on tutkittu kylmämuovattujen nelikulmaisten putkipalkkien K-liitosten mallinnusta epälineaarisella elementtimenetelmällä. Työn tärkeimpänä tavoitteena on ollut kehittää putkipalkin osien materiaalimalleja siten, että liitosten kestävyyttä voidaan tutkia laboratoriokokeiden ohella luotettavasti myös elementtimenetelmällä. Toisena tavoitteena on ollut tutkia, voidaanko putkipalkkien liitosten mitoitusohjeita turvallisesti soveltaa kylmämuovatuille putkipalkeille, joissa valmistusprosessi aiheuttaa muutoksia materiaaliominaisuuksiin, erityisesti muodonmuutoskykyyn. Työssä tehtyjen laboratoriokokeiden ja elementtianalyysien perusteella elementti-menetelmä on käyttökelpoinen työkalu putkipalkkiliitosten staattista kestävyyttä määritettäessä, kun materiaalimallit on määritetty oikein. Erityisesti liitoksen käyttö-rajatilan mukaisen kestävyyden laskennassa elementtimenetelmällä saadaan hyvin laboratoriokokeita vastaavia tuloksia. Tehdyt laboratoriokokeet osoittavat myös, että Eurocode 3:n mukaisia putkipalkkien liitosten mitoitusohjeita voi turvallisesti käyttää kylmämuovatuille putkipalkeille.

Kylmämuovattujen putkipalkkien X-liitosten äärikestävyyden ja jäykkyyden määrittäminen sekä materiaalimallin kehittäminen

Työssä on tutkittu elementtimenetelmän avulla kylmämuovattujen nelikulmaisten putkipalkkien materiaalimallin kehittämistä ja putkipalkkien X-liitosten jäykkyyden ja äärikestävyyden määrittämistä. Työn tavoitteena on tutkia kylmämuovauksen vaikutuksia putkipalkkiprofiilin materiaaliominaisuuksiin materiaalikokeiden ja elementtianalyysien avulla sekä kehittää putkipalkille anisotrooppista materiaalimallia. Työssä määritettyjä materiaalimalleja on sovellettu X-liitosten elementtimalleihin, joiden käyttäytymistä on verrattu äärikestävyyskokeiden tuloksiin. Tutkimuksen perusteella Eurocode 3:n mitoitusohjeita voidaan turvallisesti soveltaa kylmämuovattujen putkipalkkien X-liitosten laskennassa. Työssä tehtyjen materiaalikokeiden ja elementtianalyysien perusteella materiaalin anisotrooppisuuden vaikutus liitoksen kestävyyteen on vähäistä, ja putkipalkin pituussuuntaista materiaalimallia voidaan soveltaa myös kehäsuuntaisille materiaaliominaisuuksille. Materiaalikokeiden simulointi osoittaa, että elementtimenetelmää voidaan käyttää materiaalimallin määrittämisen apuvälineenä.

Vääntökuormitetun koteloprofiilipuomin väsymiskestävyys

Tässä työssä tutkittiin vääntökuormitettua hitsattua koteloprofiilipuomia. Vääntökuormitus aiheuttaa koteloprofiiliin vinouttavan voimasysteemin, joka aiheuttaa kotelopalkkiin sekä poikittaisia taivutusjännityksiä että pitkittäisiä jännityksiä. Vinoutumisen aiheuttamia lisära-situksia on tutkittu analyyttisesti BEF-analogian avulla sekä elementtimenetelmää apuna käyttäen. Lisäksi vääntökuormitus aiheuttaa puomiin estetyn väännön jännityksiä. Väsymiskestoikää tutkittiin laboratoriossa suoritettujen väsytyskokeiden avulla sekä las-kennallisesti. Kestoikälaskennassa käytettiin tehollisen lovijännityksen menetelmää hitsin juuren puolen väsymisen arvioinnissa sekä hot spot- jännityksen menetelmää hitsin rajavii-van väsymisen arvioinnissa. Teholliset lovijännitykset sekä hot spot jännitykset ovat määri-tetty elementtimenetelmän avulla. Laboratoriokokeiden ja elementtimenetelmä laskennan perusteella saatiin rakenteen kes-toiän kannalta kriittiset detaljit määritettyä. Kriittiset detaljit sijaitsevat puomin päädyn rakenteissa. Tutkimuksessa saatiin selville, että kriittisten detaljien rakenteellisilla ja valmis-tusteknisillä ratkaisuilla on merkittävä vaikutus lopullisen tuotteen väsymiskestoikään.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Experimental aspects of biomass fuels in a bubbling fluidized bed combustor

This work presents experimental information relevant to the combustion of biomass in a bubbling fluidized bed. The biomass distribution in a fluidized bed was studied through tests performed in a cold bed, while the volatiles released in the biomass pyrolysis, the burning rate of the resulting charcoal, and the combustion control regime, were studied through tests performed in a high temperature bed.Visual examination of photographs taken from a transparent walls bed, with a rectangular cross-section, showed that the large fuel particles, typical of biomass processing, were distributed in the bubbles, in the splash zone, and in the emulsion phase. The occurrence of biomass in the emulsion phase was favored by burning biomass particles of greater density and smaller size-expetimentally determined in each case. Decreasing the fuel particle size improved the biomass distribution inside the bed. The same was accomplished by increasing the superficial gas velocity as high as possible, compatibly with the acceptable elutriation.Burning tests showed that the biomass fuels have the advantage of reaching the diffusional regime at temperatures that can be lower than 1000 K, which ensures that the biomass fuels burn in a stable regime. (C) 2007 Elsevier B.V. All rights reserved.

Técnicas de reforço estrutural para edificações antigas: estudo de caso na cidade de Rio Branco – Acre

Este trabalho visou a demonstrar o dimensionamento e verificação de cálculo da NBR 6118 (ABNT, 2007) com as suas características geométricas, cobrimento da armadura, armaduras, flambagem e a resistência de pilares à compressão centrada dos pilares em concreto armado, apresentando na revisão bibliográfica as principais técnicas de reforço estrutural de pilares de concreto armado para edificações antigas, identificando as principais metodologias e técnicas utilizadas no Brasil e apresentando os pontos positivos e negativos de cada técnica:encamisamento de concreto, perfis metálicos, chapa de aço colado, manta/tecido de carbono, aramida e vidro e polímeros reforçados com fibras de carbono (PRFC). Os pilares com aumento da seção transversal retangular, com adição de armação e concreto, sendo mais usual e prática a técnica apresenta dificuldades em obras antigas, geralmente devido à necessidade arquitetônica de permanecer o mais fiel a sua forma original. Justificando-se a necessidade de conhecimento das diversas técnicas de reforço estrutural descritas neste trabalho com aumento de capacidade de resistência, sem que haja aumento substancial, na seção transversal dos pilares e objetivando a análise do reforço proposto através dos cálculos do projeto, programa – PDOP 2.0 e parâmetros de cálculo da NBR 6118 (ABNT, 2007). Os resultados obtidos através da análise comparativa do reforço executado no estudo de caso “revitalização do casarão” - com relação à análise dos pilares retangulares submetidos à flexão composta oblíqua, esforços cortantes e torsores quanto à NBR 6118 (ABNT, 2007) utilizando o programa para dimensionamento otimizado de pilares – PDOP 2.0 - indicaram que a técnica de reforço estudada foi eficiente, pois todas as peças reforçadas tiveram uma capacidade portante maior que a do pilar original sem o reforço.

Length of the annular regime for condensing flows inside a horizontal channel - the experimental determination of its values and its trends

The experiments observe and measure the length of the annular regime in fully condensing quasi-steady (steady-in-the-mean) flows of pure FC-72 vapor in a horizontal condenser (rectangular cross-section of 2 mm height, 15 mm width, and 1 m length). The sides and top of the duct are made of clear plastic that allows flow visualization. The experimental system in which this condenser is used is able to control and achieve different quasi-steady mass flow rates, inlet pressures, and wall cooling conditions (by adjustment of the temperature and flow rate of the cooling water flowing underneath the condensing-plate). The reported correlations and measurements for the annular length are also vital information for determining the length of the annular regime and proposing extended correlation (covering many vapors and a larger parameter set than the experimentally reported version here) by ongoing independent modeling and computational simulation approach.

Comportamiento de pilares de hormigón armado confinados con materiales compuestos sometidos a compresión centrada

En la actualidad muchas estructuras de hormigón armado necesitan ser reforzadas debido a diversas razones: errores en el proyecto o construcción, deterioro debido a efectos ambientales, cambios de uso o mayores requerimientos en los códigos. Los materiales compuestos, también conocidos como polímeros reforzados con fibras (FRP), están constituidos por fibras continuas de gran resistencia y rigidez embebidas en un material polimérico. Los FRP se utilizan cada vez más en aplicaciones estructurales debido a sus excelentes propiedades (elevadas resistencia y rigidez específicas y resistencia a la corrosión). Una de las aplicaciones más atractivas es el refuerzo de pilares mediante confinamiento para incrementar su resistencia y ductilidad. El confinamiento puede conseguirse pegando capas de FRP envolviendo el pilar en la dirección de los cercos (con las fibras orientadas en dirección perpendicular al eje del elemento). Se han realizado numerosos estudios experimentales en probetas cilíndricas pequeñas confinadas con encamisados de FRP y sometidas a compresión axial, y se han propuesto varios modelos sobre el hormigón confinado con FRP. Es sabido que el confinamiento de pilares de sección no circular es menos eficiente. En una sección circular, el FRP ejerce una presión de confinamiento uniforme sobre todo el perímetro, mientras que en una sección rectangular la acción de confinamiento se concentra en las esquinas. Esta tesis presenta los resultados de una investigación experimental sobre el comportamiento de probetas de hormigón de sección cuadrada confinadas con FRP y sometidas a compresión centrada. Se realizaron un total de 42 ensayos investigándose el comportamiento en las direcciones axial y transversal. Las variables del estudio incluyen: la resistencia del hormigón, el tipo de fibras (vidrio o carbono), la cuantía de refuerzo y el radio de curvatura de las esquinas. Los resultados de los ensayos realizados muestran que el confinamiento con FRP puede mejorar considerablemente la resistencia y ductilidad de pilares de hormigón armado de sección cuadrada con las esquinas redondeadas. La mejora conseguida es mayor en los hormigones de baja resistencia que en los de resistencia media. La deformación de rotura de la camisa de FRP es menor que la que se obtiene en ensayos de tracción normalizados del laminado, y la eficiencia del confinamiento depende en gran medida del radio de redondeo de las esquinas. Los resultados se han comparado con los obtenidos según los modelos teóricos más aceptados. Hay dos parámetros críticos en el ajuste de los modelos: el factor de eficiencia de la deformación y el efecto de confinamiento en secciones no circulares. Nowadays, many existing RC structures are in need of repair and strengthening for several reasons: design or construction errors, deterioration caused by environmental effects, change in use of the structures or revisions of code requirements. Composite materials, also known as fibre reinforced polymers (FRP), are composed of high strength and stiffness continuous fibres embedded in a polymer material. FRP materials are being increasingly used in many structural applications due to their excellent properties (high strength- and stiffness-toweight ratio, good corrosion behaviour). One of the most attractive applications of FRP is the confinement of concrete columns to enhance both strength and ductility. Concrete confinement can be achieved by bonding layers of hoop FRP around the column (fibres oriented perpendicular to the longitudinal axis). Many experimental studies have been conducted on small-scale plain concrete specimens of circular cross-sections confined with FRP and subjected to pure axial compressive loading, and several design models have been proposed to describe the behaviour of FRP-confined concrete. It is widely accepted that the confinement of non-circular columns is less efficient than the confinement of circular columns. In a circular cross section, the jacket exerts a uniform confining pressure over the entire perimeter. In the case of a rectangular cross section, the confining action is mostly concentrated at the corners. This thesis presents the results of a comprehensive experimental investigation on the behaviour of axially loaded square concrete specimens confined with FRP. A total of 42 compression tests were conducted, and the behaviour of the specimens in the axial and transverse directions were investigated. The parameters considered in this study are: concrete strength, type of fibres (glass or carbon), amount of FRP reinforcement and corner radius of the cross section. The tests results indicate that FRP confinement can enhance considerably the compressive strength and ductility of RC square columns with rounded corners. The enhancement is more pronounced for low- than for normal-strength concrete. The rupture strain of the FRP jacket is lower than the ultimate strain obtained by standard tensile testing of the FRP material, and the confinement efficiency significantly depends on the corner radius. The confined concrete behaviour was predicted according to the more accepted theoretical models and compared with experimental results. There are two key parameters which critically influence the fitting of the models: the strain efficiency factor and the effect of confinement in non-circular sections.

Flow patterns, performance and scale-up of distillation trays

This work is concerned with the nature of liquid flow across industrial sieve trays operating in the spray, mixed, and the emulsified flow regimes. In order to overcome the practical difficulties of removing many samples from a commercial tray, the mass transfer process was investigated in an air water simulator column by heat transfer analogy. The temperature of the warm water was measured by many thermocouples as the water flowed across the single pass 1.2 m diameter sieve tray. The thermocouples were linked to a mini computer for the storage of the data. The temperature data were then transferred to a main frame computer to generate temperature profiles - analogous to concentration profiles. A comprehensive study of the existing tray efficiency models was carried out using computerised numerical solutions. The calculated results were compared with experimental results published by the Fractionation Research Incorporation (FRl) and the existing models did not show any agreement with the experimental results. Only the Porter and Lockett model showed a reasonable agreement with the experimental results for cenain tray efficiency values. A rectangular active section tray was constructed and tested to establish the channelling effect and the result of its effect on circular tray designs. The developed flow patterns showed predominantly flat profiles and some indication of significant liquid flow through the central region of the tray. This comfirms that the rectangular tray configuration might not be a satisfactory solution for liquid maldistribution on sieve trays. For a typical industrial tray the flow of liquid as it crosses the tray from the inlet to the outlet weir could be affected by the mixing of liquid by the eddy, momentum and the weir shape in the axial or the transverse direction or both. Conventional U-shape profiles were developed when the operating conditions were such that the froth dispersion was in the mixed regime, with good liquid temperature distribution while in the spray regime. For the 12.5 mm hole diameter tray the constant temperature profiles were found to be in the axial direction while in the spray regime and in the transverse direction for the 4.5 mm hole tray. It was observed that the extent of the liquid stagnant zones at the sides of the tray depended on the tray hole diameter and was larger for the 4.5 mm hole tray. The liquid hold-up results show a high liquid hold-up at the areas of the tray with low liquid temperatures, this supports the doubts about the assumptions of constant point efficiency across an operating tray. Liquid flow over the outlet weir showed more liquid flow at the centre of the tray at high liquid loading with low liquid flow at both ends of the weir. The calculated results of the point and tray efficiency model showed a general increase in the calculated point and tray efficiencies with an increase in the weir loading, as the flow regime changed from the spray to the mixed regime the point and the tray efficiencies increased from approximately 30 to 80%.Through the mixed flow regime the efficiencies were found to remain fairly constant, and as the operating conditions were changed to maintain an emulsified flow regime there was a decrease in the resulting efficiencies. The results of the estimated coefficient of mixing for the small and large hole diameter trays show that the extent of liquid mixing on an operating tray generally increased with increasing capacity factor, but decreased with increasing weir loads. This demonstrates that above certain weir loads, the effect of eddy diffusion mechanism on the process of liquid mixing on an operating tray to be negligible.

Thick Section Laser Beam Welding of Structural Steels: Methods for Improving Welding Efficiency

Laser beam welding (LBW) is applicable for a wide range of industrial sectors and has a history of fifty years. However, it is considered an unusual method with applications typically limited to welding of thin sheet metal. With a new generation of high power lasers there has been a renewed interest in thick section LBW (also known as keyhole laser welding). There was a growing body of publications during 2001-2011 that indicates an increasing interest in laser welding for many industrial applications, and in last ten years, an increasing number of studies have examined the ways to increase the efficiency of the process. Expanding the thickness range and efficiency of LBW makes the process a possibility for industrial applications dealing with thick metal welding: shipbuilding, offshore structures, pipelines, power plants and other industries. The advantages provided by LBW, such as high process speed, high productivity, and low heat input, may revolutionize these industries and significantly reduce the process costs. The research to date has focused on either increasing the efficiency via optimizing process parameters, or on the process fundamentals, rather than on process and workpiece modifications. The argument of this thesis is that the efficiency of the laser beam process can be increased in a straightforward way in the workshop conditions. Throughout this dissertation, the term “efficiency” is used to refer to welding process efficiency, specifically, an increase in efficiency refers an increase in weld’s penetration depth without increasing laser power level or decreasing welding speed. These methods are: modifications of the workpiece – edge surface roughness and air gap between the joining plates; modification of the ambient conditions – local reduction of the pressure in the welding zone; modification of the welding process – preheating of the welding zone. Approaches to improve the efficiency are analyzed and compared both separately and combined. These experimentally proven methods confirm previous findings and contribute additional evidence which expand the opportunities for laser beam welding applications. The focus of this research was primarily on the effects of edge surface roughness preparation and pre-set air gap between the plates on weld quality and penetration depth. To date, there has been no reliable evidence that such modifications of the workpiece give a positive effect on the welding efficiency. Other methods were tested in combination with the two methods mentioned above. The most promising - combining with reduced pressure method - resulted in at least 100% increase in efficiency. The results of this thesis support the idea that joining those methods in one modified process will provide the modern engineering with a sufficient tool for many novel applications with potential benefits to a range of industries.

Comparative study of the proton beam effects between the conventional and Circular-Gate MOSFETs

The study of ionizing radiation effects on semiconductor devices is of great relevance for the global technological development and is a necessity in some strategic areas in Brazil. This work presents preliminary results of radiation effects in MOSFETs that were exposed to 3.2 Grad radiation dose produced by a 2.6-MeV proton beam. The focus of this work was to electrically characterize a Rectangular-Gate MOSFET (RGT) and a Circular-Gate MOSFET (CGT), manufactured with the On Semiconductor 0.5 mu m standard CMOS fabrication process and to verify a suitable geometry for space applications. During the experiment, I-DS x V-GS curves were measured. After irradiation, the RGT off-state current (I-OFF) increased approximately two orders of magnitude reaching practically the same value of the I-OFF in the CGT, which only doubled its value. (C) 2011 Elsevier B.V. All rights reserved.

Measurement of the νμ charged current quasielastic cross section on carbon with the T2K on-axis neutrino beam

We report a measurement of the νµ charged current quasi-elastic cross-sections on carbon in the T2K on-axis neutrino beam. The measured charged current quasi-elastic cross-sections on carbon at mean neutrino energies of 1.94 GeV and 0.93 GeV are (11.95 ± 0.19(stat.) +1.82−1.47(syst.)) ×10^−39 cm^2/neutron, and (10.64 ± 0.37(stat.)+2.03−1.65(syst.)) × 10^−39 cm^2/neutron, respectively. These results agree well with the predictions of neutrino interaction models. In addition, we investigated the effects of the nuclear model and the multi-nucleon interaction.