A simple method to simulate shrinkage-induced cracking in cement-based composites by lattice-type modeling

A new numerical procedure is proposed to investigate cracking behaviors induced by mismatch between the matrix phase and aggregates due to matrix shrinkage in cement-based composites. This kind of failure processes is simplified in this investigation as a purely spontaneous mechanical problem, therefore, one main difficulty during simulating the phenomenon lies that no explicit external load serves as the drive to propel development of this physical process. As a result, it is different from classical mechanical problems and seems hard to be solved by using directly the classical finite element method (FEM), a typical kind of "load -> medium -> response" procedures. As a solution, the actual mismatch deformation field is decomposed into two virtual fields, both of which can be obtained by the classical FEM. Then the actual response is obtained by adding together the two virtual displacement fields based on the principle of superposition. Then, critical elements are detected successively by the event-by-event technique. The micro-structure of composites is implemented by employing the generalized beam (GB) lattice model. Numerical examples are given to show the effectiveness of the method, and detailed discussions are conducted on influences of material properties.

高精度微结构聚合物光栅的复制技术

光栅复制是降低光栅制造成本,提高产量的一条有效途径。研究了利用紫外压印技术复制微结构光栅的方法。使用玻璃基底矩形浮雕结构的微结构光栅作为母光栅,给出了利用聚二甲基硅氧烷(PDMS)制作光栅模具和在光敏聚合物材料上复制微结构光栅的详细过程。经过优化工艺条件,成功地复制了一系列不同周期和开口比的微结构光栅,测试了复制光栅和母光栅的衍射图像和0级与±1级的衍射强度,结果表明,复制光栅和母光栅的衍射图像与光强分布基本一致。

不同沉积参量下ZrO_2薄膜的微结构和激光损伤阈值

ZrO2采用X射线衍射(XRD)技术分析了不同充氧条件和沉积温度对ZrO2溥膜组成结构的影响，并对不同工艺下制备的薄膜的表面粗糙度和激光损伤阈值进行了测量。结果发现随着氧压的升高，ZrO2溥膜将由单斜相多晶态逐渐转变为非晶态结构，而随着基片温度的增加，溥膜将由非晶态逐渐转变为单斜相多晶态。同时发现随着氧压升高晶粒尺寸减小，而随着沉积温度增加，晶粒尺寸增大。氧压增加时工艺对表面粗糙度有一定程度的改善，而沉积温度升高，工艺对表面粗糙度的改善不明显。晶粒尺寸大小变化与表面粗糙度变化存在对应关系。激光损伤测量表明

中国东北样带草原段关键种——羊草茎、叶显微结构的生态可塑性及群落功能群组成和多样性研究

陆地样带是国际地圈——生物圈计划(IGBP)研究中最引入注目的创新之一。目前，国际上已经设立了15条陆地样带，研究内容涉及环境梯度分析、气候变化对植被初级生产力的影响及环境变化、土地利用等与植被变化的对应关系等。沿该陆地样带分布较广的关键种生理适应性等方面对影响其生理功能形态结构的研究较少，特别是茎、叶等组织功能研究较少。 中国东北样带(NECT)是全球陆地样带的重要组成部分，多年来已开展了大量深入系统的研究工作，已成为我国生态学、地学等学科的重要研究平台。本研究以中国东北样带中西段广泛分布的重要关键种——羊草（Leymus chinensis）为研究对象，分析了羊草茎、叶显微结构的生态可塑性及其与水分利用效率的关系，进而阐述了羊草适应不同生境条件，特别是适应水分变化的机制，为揭示羊草及其种群、群落乃至以羊草为优势种或建群种的草地生态系统在全球变化背景下的发展趋势提供理论依据。 基于2001年7～8月第3次中国东北样带考察资料，采用高精度Olympus显微镜及C同位素分析技术（δ13C判别值），结合在野外取样过程中测定的样地土壤含水量和海拔高度，以及近十年各样地年降水量和年均温度气象资料，分析了羊草茎、叶显微结构和水分利用变化与环境因子的关系，以及以羊草为建群种或共建种的无牧和放牧样地群落生物量、物种多样性和植物功能型组成变化与环境因子的关系。 结果表明：羊草叶片表面及内部主要显微结构特征参数各样地间有不同程度的差异，其中气孔密度与降水量呈线性正相关。代表气孔开张程度的气孔长度和宽度变化与土壤含水量呈线性相关。叶表面角质层厚度与海拔高度变化关系较大，并以上表面角质层厚度变化最为明显，主要受海拔高度升高引起的紫外线照射增强的影响。运动细胞带宽度占叶面积比虽然与各环境因子关系不很密切，但温度变化的影响较突出，这一显微结构调整与气孔变化构成干旱——高温调节机制。叶片表面毛茸的变化也是非常显著的，但与各环境因子关系密切程度均不大，可以肯定的是在土壤水分状况较好的生境下羊草叶片表面毛茸密度及长度明显增加，而一些干旱生境中常表现为毛茸较少、较短，个别样地基本没有发育较好的毛茸。总体上看，羊草叶片对干旱化的形态结构调整以气孔密度和开张程度的变化最大，是羊草叶片调节水分利用效率的重要适应性生态可塑性调整。 与叶片相比，羊草茎横切面结构特征的变化与各环境因子关系的显著性不是很强，但各样地间的差异是比较显著的，许多结构调整可能与土壤养分条件的变化有一定关系，如茎秆粗度变化、基本薄壁组织厚度和中央空腔（髓腔）直径的变化等，但本研究未能涉及这方面内容，有待于进一步研究。 羊草水分利用效率与降水量和土壤含水量呈显著的负相关关系，即随降水量和土壤含水量增大羊草水分利用效率明显降低，蒸腾耗水增大，这一生理变化与显微结构的调整关系密切，特别是气孔密度与气孔宽度在水分较差生境中明显减小，从而有利于适应干旱环境，减少耗水量。表现比较突出的是非地带性林西样地，其降水量处于10个样地的中等偏低水平，但其δ13C判别值较低，达-26.063‰，与降水量较大的长岭、双辽样地几乎相当，并比相邻的林东和克旗样地明显低，其气孔密度、开张程度及叶脉后生导管直径均较高（大），但其土壤水分状况是最好的样地之一，尽管取样时不幸遇到雨天，但从其群落类型——羊草杂类草草甸，并伴生许多中、湿生种类上看，其生境的湿润程度是毋庸置疑的。这一非地带性样地中羊草结构的变化从另一侧面反映了羊草显微结构调整对水分环境的适应。δ13C判别值是一个非常敏感的参数，在分析植物水分利用效率及其相关领域的研究中应深入利用。 群落植物功能群组成与环境因子及群落初级生产力关系研究结果表明，丛生禾草生长型功能群、旱生和中旱生植物水分生态类型功能群具有明显的地带性变化规律，并与群落生物量变化关系密切，变异性较低，占群落生物量比例较大，可考虑作为植物功能型组合对无牧样地植被变化进行评估和预测。在放牧影响下，C4植物光合类型功能群呈现明显的地带性变化，并在群落中所起的作用明显增强，亦可考虑作为评估和预测植被变化的植物功能型组合。无牧样地与放牧样地研究结果均表明，按Raunkiaer划分的地面芽、地下芽、地上芽和一年生植物生活型功能群，其地带性变化不明显，或变异率高，或占群落生物量比例小，不宜作植物功能群组合对植被变化进行评估和预测。

Hardfacing using supersonic laser depostion of stellite-6

The capability of manufacturing coatings is of central importance in engineering design. Many components require nowadays the application of additional layers, to enhance mechanical properties and protect against hostile environments. Supersonic Laser Deposition (SLD) is a novel coating method, based upon Cold Spray (CS) principles. In this technique the deposition velocities can be significantly lower than those required for effective bonding in CS applications. The addition of laser heat energy permits a change in the thermodynamic experience of impacting particles, thereby offering a greater opportunity for metallurgical bonding at lower velocities compared to the CS process technology. The work reported in this paper demonstrates the ability of the SLD process to deliver hard facing materials to engineering surfaces. Stellite-6 has been deposited on low carbon steel tubes over a range of process parameters, determining the appropriate target power and traverse speeds for coating deposition. Coating properties and parameters were examined to determine the main properties, micro-structure and processing cost. Their morphology was studied through optical microscopy, SEM and X-Ray Diffraction. The results have shown that SLD is capable of depositing Stellite-6, with enhanced properties compared to laser clad counterparts.

Orthorhombic α-moo 3 coatings with lath-shaped morphology developed by SPPS: Applications to super-capacitors

Electrical double-layer capacitors owe their large capacitance to the formation of a double-layer at the electrode/electrolyte interface of high surface area carbon-based electrode materials. Greater electrical energy storage capacity has been attributed to transition metal oxides/nitrides that undergo fast, reversible redox reactions at the electrode surface (pseudo-capacitive behavior) in addition to forming electrical double-layers. Solution Precursor Plasma Spray (SPPS) has shown promise for depositing porous, high surface area transition metal oxides. This investigation explored the potential of SPPS to fabricate a-MoO 3 coatings with micro-structures suitable for use as super-capacitor electrodes. The effects of number of spray passes, spray distance, solution concentration, flow rate and spray velocity on the chemistry and micro-structure of the a-MoO 3 deposits were examined. DTA/TGA, SEM, XRD, and electrochemical analyses were performed to characterize the coatings. The results demonstrate the importance of post-deposition heating of the deposit by subsequent passes of the plasma on the coating morphology. © ASM International.

Permeability of aged grout around tunnels in London

Prediction of the long-term settlement of clay soils over tunnels requires a knowledge of the permeability of the soil and of the tunnel lining; however, determination of the lining permeability in the field is difficult. An important contributor to this problem is the lack of knowledge concerning the permeability of the grout between the lining and the soil. This paper presents the results of tests to characterise the properties of grout samples from London Underground tunnels, investigating permeability, porosity, micro structure and composition. The tests revealed that the newer grout was impermeable relative to the surrounding clay. However, the older samples showed much greater permeabilities and an altered grout composition, suggesting that degradation had taken place. Exposure to groundwater appeared to have caused carbonation and sulfate reaction. The combination of chemical reaction and leaching of cementitious and degradation products appears to have made these grouts more permeable, so that the grout could act as a drainage path rather than a barrier. This challenges the typical assumption that the grout acts as an impermeable barrier.

A study of the suppression of the high-temperature helium embrittlement in an oxide-particle dispersion strengthened alloy

In this paper, an investigation on the micro-structure of an Fe-base oxide-dispersion-strengthened (ODS) alloy irradiated with high-energy Ne-20 ions to different doses at a temperature around 0.5T(m) (T-m is the melting point of the alloy) is presented. Investigation with the transmission electron microscopy found that the accelerated growth of voids at grain-boundaries, which is usually a concern in conventional Fe-base alloys under conditions of inert-gas implantation, was not observed in the ODS alloy irradiated even to the highest dose (12000 at.ppm Ne). The reason is ascribed to the enhanced recombination of point defects and strong trapping of Ne atoms at the interfaces of the nano-scale oxide particles in grains. The study showed that ODS alloys have good resistance to the high-temperature inter-granular embrittlement due to inert-gas accumulation, exhibiting prominence of application in harsh situations of considerable helium production at elevated temperatures like in a fusion reactor.

Solvent induced different morphologies of bis(propyl)triethoxysilane substituted perylenediimide and their optical properties

Nano/microstructure of bis(propyl)triethoxysilane substituted perylenediimide (1) with nanoparticle and twisted microrod morphologies were obtained by reprecipitation method induced by water and petroleum ether, respectively. It is believed that the different nucleation and growth processes involved are responsible for the formation of the nano/micro-structure With different morphologies of 1. UV-vis absorption and photoluminescence measurements show that their UV-vis absorption and photoluminescence properties are different from each other as well as their monomer mid bulk materials due to the different effects on the change transfer (CT) transition energy levels caused by their different aggregation behaviors.

基于软粘土微观特性的非线性固结理论研究

The land subsidence of soft clay is including natural and man-made content, which leads to the research on the mechanism of land subsidence constituted by two different aspects, which are studied by geological engineers and geologist. The main major research is focused on the effects of engineering. The land subsidence engineering of soil mechanics is caused by the consolidation and compression of soft clay, the content of which is including the micro-structural characteristics, the stress - strain constitutive relation, porous law, and consolidation theory. In this paper, it is discussed the nonlinear consolidation and compression theory of soft clay. The main studies and conclusions of this thesis are as follows. （1）The micro-structure and its stability are closely related to the engineering characters of soft clay. The stiffness and force connection status of micro-structure plays a controlling influence to its stability. （2）Under saturated state, clay particles remain in a non-full contact or non-contact status, so it is needed to modify the Terzaghi effective stress principle. With the discharge of pore water, the effective stress is increasing, and part of weakly bound-water begins flow, while the porosity and permeability are became lower. （3）It exist non-linear flow in soft clay, which is caused by the shear flow situation of weakly bounded-water. In this case, permeability coefficient is a nonlinear function of hydraulic gradient. （4）In the initial consolidation stage of soft clay in the initial stage, the porous flow is mainly caused by the excretion of free water. With the decrease of free water content, combined bonded-water start to supply free water. At the later stage of consolidation, the flow of fluid is mainly consisted by weakly bounded-water. The exchange between bonded-water and free water is played a role, which slows down the consolidation process.

陡坡带砂砾岩体油气成藏模式研究——以东营凹陷西北部陡坡带为例

Based on the study of sequence stratigraphy, modern sedimentary, basin analysis, and petroleum system in abrupt slop of depression, this paper builds sedimentary system and model, sandy bodies distribution, and pool-forming mechanism of subtle trap. There are some conclusions and views as follows. By a lot of well logging and seismic analysis, the author founded up the sequence stratigraphic of the abrupt slope, systematically illustrated the abrupt slope constructive framework, and pointed out that there was a special characteristics which was that south-north could be divided to several fault block and east-west could be carved up groove and the bridge in studying area. Based all these, the author divided the studying area to 3 fault block zone in which because of the groove became the basement rock channel down which ancient rivers breathed into the lake, the alluvial fan or fan delta were formed. In the paper, the author illustrated the depositional system and depositional model of abrupt slope zone, and distinguished 16 kinds of lithofacies and 3 kinds of depositional systems which were the alluvial fan and fan-delta system, lake system and the turbidite fan or turbidity current deposition. It is first time to expound completely the genetic pattern and distributing rule of the abrupt slope sandy-conglomeratic fan bodies. The abrupt slope sandy-conglomeratic fan bodies distribute around the heaves showing itself circularity shape. In studying area, the sandy-conglomeratic fan bodies mainly distribute up the southern slope of Binxian heave and Chenjiazhuang heave. There mainly are these sandy-conglomeratic fan body colony which distributes at a wide rage including the alluvial fan, sub-water fluvial and the turbidite fan or the other turbidity current deposition in the I fault block of the Wangzhuang area. In the II fault block there are fan-delta front and sub-water fluvial. And in the Binnan area, there mainly are those the alluvial fan (down the basement rock channel) and the sandy-conglomeratic fan body which formed as narrowband sub-water fluvial (the position of bridge of a nose) in the I fault block, the fan-delta front sandy-conglomeratic fan body in the H fault block and the fan-delta front and the turbidity current deposition sandy-conglomeratic fan body in the m fault block. Based on the reservoir outstanding characteristics of complex classic composition and the low texture maturity, the author comparted the reservoir micro-structure of the Sha-III and Sha-IV member to 4 types including the viscous crude cementation type, the pad cementation type, the calcite pore-funds type and the complex filling type, and hereby synthetically evaluated 4 types sandy- conglomeratic fan body reservoir. In the west-north abrupt slope zone of Dongying Depression, the crude oil source is belonging to the Sha-III and Sha-IV member, the deep oil of Lijin oilfield respectively come from the Sha-III and Sha-IV member, which belongs to the autogeny and original deposition type; and the more crude oil producing by Sha-IV member was migrated to the Wangzhuan area and Zhengjia area. The crude oil of Binnan oil-field and Shanjiasi oil-field belongs to mixed genetic. It is the first time to illustrate systematically the genetic of the viscous crude that largely being in the studying area, which are that the dissipation of the light component after pool-forming, the biological gradation action and the bath-oxidation action, these oil accumulation belonging to the secondary viscous crude accumulation. It is also the first time to compart the studying area to 5 pool-forming dynamical system that have the characteristic including the common pressure and abnormal pressure system, the self-fountain and other-fountain system and the closing and half-closing system etc. The 5 dynamical systems reciprocally interconnected via the disappearance or merger of the Ethology and the fluid pressure compartment zone, the fault and the unconformity surface, hereby formed duplicated pattern oil-gas collecting zone. Three oil-gas pool-forming pattern were founded, which included the self-fountain side-direction migrated collecting pattern, the self-fountain side-direction ladder-shape pool-forming pattern and the other-fountain pressure releasing zone migrated collecting pattern. A series of systemic sandy-conglomeratic fan bodies oil-gas predicting theory and method was founded, based on the groove-fan corresponding relation to confirm the favorable aim area, according as the characteristic of seismic-facies to identify qualitatively the sandy-conglomeratic fan bodies or its scale, used the temporal and frequency analysis technique to score the interior structure of the sandy- conglomeratic fan bodies, applied for coherent-data system analysis technology to describe the boundary of the sandy-conglomeratic fan bodies, and utilized the well logging restriction inversion technique to trace quantificational and forecast the sandy-conglomeratic fan bodies. Applied this technique, totally 15 beneficial sandy-conglomeratic fan bodies were predicted, in studying area the exploration was preferably guided, and the larger economic benefit and social benefit was acquired.

胜坨油田沙二段油藏流场剩余油形成机理和分布模式

By applying multi-discipline theory and methods comprehensively and with full use of computer, the paper deeps into studying changing rule and control factor of fluid field of ES2 Shengtuo oil field during waterflood development, physical and chemical function, and stress. Matrix field, network field, fluid field, stress field and physical chemistry field and fluid model for dynamic function were established. Macroscopic and microscopic genesis mechanics, distribution rule and control factor of remaining oil were revealed. Remaining oil and emulate model were established. Macroscopic and microscopic distribution rule of mover remaining oil were predicted, several results were achieved as following: The distribution of remaining oil was controlled by micro-structure. At the same development stage, remaining oil saturation of the wells located in higher position of micro-structure is higher than the average saturation in the same layer. The water content ratio has same law. It is the enrichment district that the high position of micro-structure controlled by seal faults. The remaining oil distribution was affected by sedimentary micro-facies, micro-structure, fault sealing, reservoir heterogeneity and affusion-oil extraction. On the plane, the zone owning higher saturation of remaining oil is the area that at the edge miacro-facies and sand-body distribution discontinuously; on the section, the content of waterflood of the upper or middle-upper oil layer of positive rhythm and positive comprehensive rhythm is lower, middle and weak waterflood is main, remaining oil is in enrichment relatively. The remaining oil is relative enrichment at the zones of well network of affusion and oil extraction not affected. 4D dynamic model of reservoir of Es2in Shengtuo oil field was established. Macroscopic and microscopic forming mechanics, distribution rule and control factor were revealed. The emulate model of dynamic function of Shengtuo oil field was established, the space distribution of remaining oil were predicted. Reservoir flow field, matrix field, network field, seep field, physical and chemical field, stress field and fluid field models were established. Reservoir flow field character and distribution were revealed. An improvement of the development geology theory in continental fault depression continental basin was brought on.

Redox cycling of Ni-YSZ anode investigated by TPR technique

Effect of redox cycling on a Ni-YSZ anode prepared from 50 wt.% NiO and 50 wt.% YSZ was investigated by using temperature-programmed reduction (TPR), XRD and SEM techniques. XRD results showed that NiO was formed during re-oxidation. Both the XRD and TPR results depicted that the conversion of nickel to NiO depended on the re-oxidation temperature. The oxidation of Ni to NiO occurred quickly in the initial several minutes and then reached a quasi equilibrium. The TPR profiles tracing the redox cycling showed that it brought continuous changes in the NiO micro-structure at 800 degrees C, whereas at 600 degrees C it had only little effects on the reduction of NiO. Re-oxidation resulted in the formation of spongy aggregates of NiO crystallites. Redox cycling at 800 degrees C led to a continuous decrease in the primary crystallite size of NiO and a high dispersion of the Ni particles. A continuous expansion of the slice sample was observed in both of the oxidized and reduced states during the redox cycling at 800 degrees C, whereas this process did not occur during the redox cycling at 600 degrees C. (c) 2005 Elsevier B.V All rights reserved.

The D-CIXS X-ray mapping spectrometer on SMART-1

Grande, Manuel; Browning, R.; Waltham, N.; Parker, D., 'The D-CIXS X-ray mapping spectrometer on SMART-1', Planetary and Space Science (2003) 51(6) pp.427-433 RAE2008