Influencia de diferentes condiciones de curado en la estructura porosa y en las propiedades a edades tempranas de morteros que contienen ceniza volante y escoria de alto horno

En este trabajo se ha estudiado la evolución de la microestructura, propiedades de durabilidad y resistencias mecánicas de morteros preparados con cementos comerciales, que contienen ceniza volante (entre un 21% y un 35%) y escoria de alto horno (entre un 66% y un 80%), expuestos a tres ambientes, un ambiente óptimo de laboratorio, y dos ambientes representativos del clima Atlántico y Mediterráneo respectivamente. Como referencia de comportamiento, también se ensayaron morteros de cemento Portland. La microestructura se caracterizó mediante porosimetría de intrusión de mercurio. En lo referente a la durabilidad, se estudiaron los coeficientes de absorción capilar y de migración de cloruros en estado no estacionario. También se determinó la resistencia a compresión de los morteros. Los ensayos se realizaron a 7, 28 y 90 días. La principal conclusión alcanzada es que los cementos con cenizas y escorias expuestos a condiciones ambientales representativas de los climas Atlántico y Mediterráneo, pueden desarrollar unas propiedades en servicio adecuadas al cabo de tres meses.

Fire-resistance, physical, and mechanical characterization of particleboard containing Oceanic Posidonia waste

In this work, particleboards manufactured with Oceanic Posidonia waste and bonded with cement are investigated. The particleboards are made with 3/1.5/0.5 parts of cement per part of Posidonia waste. The physical properties of bulk density, swelling, surface absorption, and dimensional changes due to relative humidity as well as the mechanical properties of modulus of elasticity, bending strength, surface soundness, perpendicular tensile strength and impact resistance are studied. In terms of the above properties, the best results were obtained for particleboards with high cement content and when the waste “leaves” are treated (crushed) before board fabrication, due to internal changes to the board structure under these conditions. Based on the results of fire tests, the particleboard is non-flammable without any fire-resistant treatment.

Propiedades físicas y mecánicas de una calcarenita: la Piedra de San Julián

En este trabajo se estudian las características físico-mecánicas de la Piedra de San Julián y su comportamiento frente a procesos de calentamiento a temperaturas similares a las alcanzadas en un incendio, así como la puesta a punto y validación de métodos dinámicos no destructivos para el dictamen del estado de desgaste del material. El enfoque está orientado a los parámetros que más interesan en la utilización de la Piedra como material de construcción. Dado que esta Tesis se realiza por compendio de artículos, por razones prácticas y necesidades de publicación, el contenido de la misma está dividido en tres grandes bloques, como son: fluencia, exposición a altas temperaturas y relación entre módulos estáticos y dinámicos. Para el estudio de la fluencia o deformabilidad a largo plazo bajo carga constante se han realizado ensayos de carga estáticos de larga duración. Por otra parte, se ha efectuado un análisis del comportamiento reológico del hormigón en las distintas normativas, especialmente en el Código Modelo FIB (2010), y se ha buscado un paralelismo entre las previsiones del Código y los resultados obtenidos en los ensayos. Al mismo tiempo se han probado varios modelos reológicos que reproduzcan de forma precisa el comportamiento de la fluencia según el Código y los ensayos. Esto ha permitido ajustar una función, adaptando las especificaciones del Código modelo, que describe la deformación en el tiempo de la Piedra de San Julián. La validez teórica de esta ecuación alcanza períodos temporales similares a los existentes para los ensayos realizados con hormigón. El modelo reológico que se ha obtenido por ajuste de todo el período anterior, consta de cuatro celdas de Kelvin y predice igualmente la deformación por fluencia de la roca. La correcta evaluación de las deformaciones a largo plazo es necesaria siempre que se estudie la intervención en edificaciones históricas, bien sea variando la distribución de cargas, o simplemente realizando obras de mantenimiento de cierto calado. La influencia de la temperatura alcanzada y del proceso de enfriamiento utilizado, se ha analizado sobre 55 muestras de roca calentando a temperaturas de hasta 600 ºC y enfriando por dos métodos: al aire y mediante inmersión en agua, ambas a temperatura ambiente. Los parámetros controlados antes y después del proceso térmico han sido: porosidades abierta y total velocidad de propagación de ondas ultrasónicas, módulo de elasticidad, coeficiente de Poisson, resistencia a compresión uniaxial (UCS) y durabilidad según el ensayo de sequedad, humedad y desmoronamiento, Slake Durability Test (SDT). Como conclusiones más notables cabe destacar: la UCS disminuye en un 35% y en un 5O% según el enfriamiento se haya realizado al aire o por inmersión, mientras que el módulo de elasticidad se reduce entre un 75% y un 80%. Las conclusiones obtenidas son importantes para la determinación del daño estructural producido en un incendio, así como para evaluar la influencia del método de extinción. Por otra parte, pueden servir para estimar indirectamente la temperatura máxima alcanzada en un incendio, de cara a la determinación de los posibles efectos sobre otros elementos constructivos. Para la relación entre módulos estáticos y dinámicos se han estudiado 24 muestras con diferentes grados de deterioro. Con los datos obtenidos en los ensayos se han analizado estadísticamente quince modelos de relación con diferentes combinaciones de variables, y se ha construido la correspondiente matriz de correlación. El coeficiente de determinación más alto corresponde a una relación lineal entre ambos módulos. La determinación del módulo de elasticidad por medios no destructivos y de fácil implementación es muy útil cuando se trata de dictaminar sobre el envejecimiento de un material estructural de este tipo. El valor del módulo con respecto al de la roca intacta es un indicador de las características resistentes y grado de debilitamiento del material. Sin embargo, el módulo bajo cargas gravitatorias -estáticas- difiere en general del obtenido dinámicamente, de una manera diferente según el material que se analice. Aquí se ha obtenido una expresión, que correlaciona con un alto valor del coeficiente de determinación ambos módulos, para la roca estudiada. Los parámetros, relaciones y modelos estudiados y propuestos en esta tesis, suponen un importante avance científico de gran utilidad para la conservación y restauración del patrimonio de edificios y otras obras de carácter histórico-cultural construidas con la Piedra de San Julián. Asimismo, las conclusiones obtenidas y los medios y métodos empleados podrán ser extrapolados a otros materiales similares con las adaptaciones oportunas.

Evaluación de las propiedades mecánicas de materiales compuestos elaborados a partir de cenizas volantes y polímeros reciclados

En el presente artículo se evalúan las propiedades mecánicas de los materiales compuestos basados en cenizas volantes de carbón de la central termoeléctrica de Termozipa combinadas con los película extensible (Stretch film), polietilenos de baja densidad lineal de pos-consumo y polímero termoplástico parcialmente cristalino pos- industrial. Se obtuvieron mezclas variando el contenido de cenizas volantes de 0 a 50 % en peso en cada uno de los tres materiales poliméricos, dentro de una máquina mezcladora tipo Brabender. Las propiedades mecánicas evaluadas fueron: resistencia a la tracción, dureza Shore D, y absorción de energía. Los resultados obtenidos indican que en todos los casos a medida que se agrega ceniza volante las propiedades mecánicas aumentan.

Mechanical behavior of rock joints: influence of joint roughness on its closure and shear behavior

En esta tesis se estudia la fricción en juntas rocosas utilizando el Método de Elementos Discretos (DEM). En particular, se estudia la influencia de la rugosidad de las superficies de la junta, la elasticidad, la fractura, y el nivel de carga de compresión sobre el comportamiento de cierre y de cizalla de las juntas rocosas. Por primera vez la rugosidad de las juntas considerada como auto-afín es utilizada para estudiar la fricción de juntas rocosas, la rugosidad se describe mediante tres parámetros: el exponente de rugosidad, la longitud de correlación auto-afín y la varianza de alturas. Mediante un algoritmo de computadora basado en métodos espectrales, ocho superficies autoafines isotrópicas con diferente rugosidad fueron creadas. Posteriormente, las ocho superficies fueron utilizadas como moldes para generar las juntas utilizando elementos discretos. Antes de realizar las simulaciones de compresión y cizallaura, se calibraron las propiedades elásticas y de fractura (criterio de fractura elíptico basado en esfuerzos) de las juntas numéricas a los datos experimentales (obtenidos previamente) de unas muestras de mortero mediante la utilización de un volumen elemental representativo (REV). Una vez que las propiedades mecánicas de las juntas se obtuvieron mediante la calibración del REV, se realizaron las pruebas de cierre (prueba de compresión) de las ocho juntas DEM. Se utilizaron dos niveles de esfuerzo de compresión para las pruebas de cierre: 14 MPa y 21 MPa. Después, las ocho juntas DEM fueron cizalladas en dos direcciones mutuamente perpendiculares. Para cada dirección de cizalla y cada nivel de esfuerzo de compresión (14 y 21 MPa), las juntas fueron cizalladas usando uno de los tres modelos mecánicos siguientes: 1) un modelo rígido, en el que las juntas no se pueden deformar, excepto en su superficie, 2) un modelo puramente elástico, en el que las juntas se pueden deformar en todo su volumen y 3) un modelo elástico con fractura en el que las juntas se pueden deformar en su volumen y, si el esfuerzo sobre las uniones entre partículas excede cierto nivel de esfuerzo máximo, las uniones se rompen de una manera irreversible. El uso de estos tres modelos mecánicos nos permitirá estudiar de manera sistemática: la influencia de la rugosidad (modelo rígido), la influencia de la elasticidad y rugosidad (modelo puramente elástico) y, finalmente, el efecto combinado de la rugosidad de las juntas, la elasticidad y la fractura (modelo elástico con fractura). El estudio de los resultados obtenidos de las simulaciones DEM es seguido por una análisis energético el cual permite estudiar la evolución de los diferentes tipos de energía en función del desplazamiento de cizalla: energía elástica almacenada en el sistema, energía de fricción entre elementos discretos, el trabajo relacionado con la dilatación de la junta y la energía disipada por el amortiguamiento interno del DEM.

The Crosslinking Degree Controls The Mechanical, Rheological, And Swelling Properties Of Hyaluronic Acid Microparticles.

Viscosupplements, used for treating joint and cartilage diseases, restore the rheological properties of synovial fluid, regulate joint homeostasis and act as scaffolds for cell growth and tissue regeneration. Most viscosupplements are hydrogels composed of hyaluronic acid (HA) microparticles suspended in fluid HA. These microparticles are crosslinked with chemicals to assure their stability against enzyme degradation and to prolong the action of the viscosupplement. However, the crosslinking also modifies the mechanical, swelling and rheological properties of the HA microparticle hydrogels, with consequences on the effectiveness of the application. The aim of this study is to correlate the crosslinking degree (CD) with these properties to achieve modulation of HA/DVS microparticles through CD control. Because divinyl sulfone (DVS) is the usual crosslinker of HA in viscosupplements, we examined the effects of CD by preparing HA microparticles at 1:1, 2:1, 3:1, and 5:1 HA/DVS mass ratios. The CD was calculated from inductively coupled plasma spectrometry data. HA microparticles were previously sized to a mean diameter of 87.5 µm. Higher CD increased the viscoelasticity and the extrusion force and reduced the swelling of the HA microparticle hydrogels, which also showed Newtonian pseudoplastic behavior and were classified as covalent weak. The hydrogels were not cytotoxic to fibroblasts according to an MTT (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide) assay. © 2014 Wiley Periodicals, Inc. J Biomed Mater Res Part A, 2014.

Assessment Of The Fixation Of Mandibular Symphysis Fractures Using Conical Cannulated Screws: Mechanical And Photoelastic Tests.

The aim of this study was to use mechanical and photoelastic tests to compare the performance of cannulated screws with other fixation methods in mandibular symphysis fractures. Ten polyurethane mandibles were allocated to each group and fixed as follows: group PRP, 2 perpendicular miniplates; group PLL, 1 miniplate and 1 plate, parallel; and group CS, 2 cannulated screws. Vertical linear loading tests were performed. The differences between mean values were analyzed with the Tukey test. The photoelastic test was carried out using a polariscope. The results revealed differences between the CS and PRP groups at 1, 3, 5, and 10 millimeters of displacement. The photoelastic test confirmed higher stress concentration in all groups close to the mandibular base, whereas the CS group showed it throughout the region assessed. Conical cannulated screws performed well in mechanical and photoelastic tests.

Peripheral P2x7 Receptor-induced Mechanical Hyperalgesia Is Mediated By Bradykinin.

P2X7 receptors play an important role in inflammatory hyperalgesia, but the mechanisms involved in their hyperalgesic role are not completely understood. In this study, we hypothesized that P2X7 receptor activation induces mechanical hyperalgesia via the inflammatory mediators bradykinin, sympathomimetic amines, prostaglandin E2 (PGE2), and pro-inflammatory cytokines and via neutrophil migration in rats. We found that 2'(3')-O-(4-benzoylbenzoyl)adenosine 5'-triphosphate triethylammonium salt (BzATP), the most potent P2X7 receptor agonist available, induced a dose-dependent mechanical hyperalgesia that was blocked by the P2X7 receptor-selective antagonist A-438079 but unaffected by the P2X1,3,2/3 receptor antagonist TNP-ATP. These findings confirm that, although BzATP also acts at both P2X1 and P2X3 receptors, BzATP-induced hyperalgesia was mediated only by P2X7 receptor activation. Co-administration of selective antagonists of bradykinin B1 (Des-Arg(8)-Leu(9)-BK (DALBK)) or B2 receptors (bradyzide), β1 (atenolol) or β2 adrenoceptors (ICI 118,551), or local pre-treatment with the cyclooxygenase inhibitor indomethacin or the nonspecific selectin inhibitor fucoidan each significantly reduced BzATP-induced mechanical hyperalgesia in the rat hind paw. BzATP also induced the release of the pro-inflammatory cytokines tumor necrosis factor α (TNF-α), interleukin (IL)-1β, IL-6 and cytokine-induced neutrophil chemoattractant-1 (CINC-1), an effect that was significantly reduced by A-438079. Co-administration of DALBK or bradyzide with BzATP significantly reduced BzATP-induced IL-1β and CINC-1 release. These results indicate that peripheral P2X7 receptor activation induces mechanical hyperalgesia via inflammatory mediators, especially bradykinin, which may contribute to pro-inflammatory cytokine release. These pro-inflammatory cytokines in turn may mediate the contributions of PGE2, sympathomimetic amines and neutrophil migration to the mechanical hyperalgesia induced by local P2X7 receptor activation.

Mechanical Properties And Fracture Dynamics Of Silicene Membranes.

As graphene has become one of the most important materials, there is renewed interest in other similar structures. One example is silicene, the silicon analogue of graphene. It shares some of the remarkable graphene properties, such as the Dirac cone, but presents some distinct ones, such as a pronounced structural buckling. We have investigated, through density functional based tight-binding (DFTB), as well as reactive molecular dynamics (using ReaxFF), the mechanical properties of suspended single-layer silicene. We calculated the elastic constants, analyzed the fracture patterns and edge reconstructions. We also addressed the stress distributions, unbuckling mechanisms and the fracture dependence on the temperature. We analysed the differences due to distinct edge morphologies, namely zigzag and armchair.

Influence Of Fluorescent Dye On Physical-mechanical Properties Of Luting Cements For Confocal Microscopy Analysis.

To evaluate the influence of a fluorescent dye (rhodamine B) on the physical and mechanical properties of three different luting cements: a conventional adhesive luting cement (RelyX ARC, 3M/ESPE), a self-adhesive luting cement (RelyX U-200, 3M/ESPE), and a self-etching and self-adhesive luting cement (SeT PP, SDI). The cements were mixed with 0.03 wt% rhodamine B, formed into bar-shaped specimens (n = 10), and light cured using an LED curing unit (Radii, SDI) with a radiant exposure of 32 J/cm(2) . The Knoop hardness (KHN), flexural strength (FS), and Young's modulus (YM) analyses were evaluated after storage for 24 h. Outcomes were subjected to two-way ANOVA and Tukey's test (P = 0.05) for multiple comparisons. No significant differences in FS or YM were observed among the tested groups (P ≥ 0.05); the addition of rhodamine B increased the hardness of the luting cements tested. The addition of a fluorescent agent at 0.03 wt% concentration does not negatively affect the physical-mechanical properties of the luting cement polymerization behavior.

Obesity Versus Osteoarthritis: Beyond The Mechanical Overload.

Obesity is currently considered a major public health problem in the world, already reaching epidemic characteristics, according to the World Health Organization. Excess weight is the major risk factor associated with various diseases, such as type 2 diabetes mellitus, hypertension, dyslipidemia and osteometabolic diseases, including osteoporosis and osteoarthritis. Osteoarthritis is the most prevalent rheumatic disease and the leading cause of physical disability and reduced quality of life of the population over 65 years. It mainly involves the joints that bear weight - knees and hips. However, along with the cases of obesity, its prevalence is increasing, and even in other joints, such as hands. Thus, it is assumed that the influence of obesity on the development of OA is beyond mechanical overload. The purpose of this review was to correlate the possible mechanisms underlying the genesis and development of these two diseases. Increased fat mass is directly proportional to excessive consumption of saturated fatty acids, responsible for systemic low-grade inflammation condition and insulin and leptin resistance. At high levels, leptin assumes inflammatory characteristics and acts in the articular cartilage, triggering the inflammatory process and changing homeostasis this tissue with consequent degeneration. We conclude that obesity is a risk factor for osteoarthritis and that physical activity and changes in diet composition can reverse the inflammatory and leptin resistance, reducing progression or preventing the onset of osteoarthritis.

Effectiveness Of The Endotracheal Tube Cuff On The Trachea: Physical And Mechanical Aspects.

The inflation pressure of the endotracheal tube cuff can cause ischemia of the tracheal mucosa at high pressures; thus, it can cause important tracheal morbidity and tracheal microaspiration of the oropharyngeal secretion, or it can even cause pneumonia associated with mechanical ventilation if the pressure of the cuff is insufficient. In order to investigate the effectiveness of the RUSCH® 7.5 mm endotracheal tube cuff, this study was designed to investigate the physical and mechanical aspects of the cuff in contact with the trachea. For this end, we developed an in vitro experimental model to assess the flow of dye (methylene blue) by the inflated cuff on the wall of the artificial material. We also designed an in vivo study with 12 Large White pigs under endotracheal intubation. We instilled the same dye in the oral cavity of the animals, and we analyzed the presence or not of leakage in the trachea after the region of the cuff after their deaths (animal sacrifice). All cuffs were inflated at the pressure of 30 cmH2O. We observed the passage of fluids through the cuff in all in vitro and in vivo experimental models. We conclude that, as well as several other cuff models in the literature, the RUSCH® 7.5 mm tube cuffs are also not able to completely seal the trachea and thus prevent aspiration of oropharyngeal secretions. Other prevention measures should be taken.

Comparative In vitro Mechanical Evaluation Of Techniques Using A 2.0 mm Locking Fixation System For Simulated Fractures Of The Mandibular Body.

To perform a comparative evaluation of the mechanical resistance of simulated fractures of the mandibular body which were repaired using different fixation techniques with two different brands of 2.0 mm locking fixation systems. Four aluminum hemimandibles with linear sectioning simulating a mandibular body fracture were used as the substrates and were fixed using the two techniques and two different brands of fixation plate. These were divided into four groups: groups I and II were fixed with one four-hole plate, with four 6 mm screws in the tension zone and one four-hole plate, with four 10 mm screws in the compression zone; and groups III and IV were fixed with one four-hole plate with four 6 mm screws in the neutral zone. Fixation plates manufactured by Tóride were used for groups I and III, and by Traumec for groups II and IV. The hemimandibles were submitted to vertical, linear load testing in an Instron 4411 servohydraulic mechanical testing unit, and the load/displacement (3 mm, 5 mm and 7 mm) and the peak loads were measured. Means and standard deviations were evaluated applying variance analysis with a significance level of 5%. The only significant difference between the brands was seen at displacements of 7 mm. Comparing the techniques, groups I and II showed higher mechanical strength than groups III and IV, as expected. For the treatment of mandibular linear body fracture, two locking plates, one in the tension zone and another in the compression zone, have a greater mechanical strength than a single locking plate in the neutral zone.

Mechanical And Photoelastic Analysis Of Four Different Fixation Methods For Mandibular Body Fractures.

The aim of the present study was to compare four methods of fixation in mandibular body fractures. Mechanical and photoelastic tests were performed using polyurethane and photoelastic resin mandibles, respectively. The study groups contained the following: (I), two miniplates of 2.0 mm; (II) one 2.0 mm plate and an Erich arch bar; (III) one 2.4 mm plate and an Erich arch bar, and (IV) one 2.0 mm plate and one 2.4 mm plate. The differences between the mean values were analyzed using Tukey's test, the Mann-Whitney test and the Bonferroni correction. Group II recorded the lowest resistance, followed by groups I, IV and III. The photoelastic test confirmed the increase of tension in group II. The 2.4 mm system board in linear mandibular body fractures provided more resistance and the use of only one 2.0 mm plate in the central area of the mandible created higher tension.

Development Plates For Stable Internal Fixation: Study Of Mechanical Resistance In Simulated Fractures Of The Mandibular Condyle.

To develop Y-shaped plates with different thicknesses to be used in simulated fractures of the mandibular condyle. Ten plates were developed in Y shape, containing eight holes, and 30 synthetic polyurethane mandible replicas were developed for the study. The load test was performed on an Instron Model 4411 universal testing machine, applying load in the mediolateral and anterior-posterior positions on the head of the condyle. Two-way ANOVA with Tukey testing with a 5% significance level was used. It was observed that when the load was applied in the medial-lateral plate of greater thickness (1.5 mm), it gave the highest strength, while in the anteroposterior direction, the plate with the highest resistance was of the lesser thickness (0.6 mm). A plate with a thickness of 1.5 mm was the one with the highest average value for all displacements. In the anteroposterior direction, the highest values of resistance were seen in the displacement of 15 mm. After comparing the values of the biomechanical testing found in the scientific literature, it is suggested that the use of Y plates are suitable for use in subcondylar fractures within the limitations of the study.