Experiments on and thermodynamic analysis of a turbocharged engine with producer gas as fuel

This article presents the studies conducted on turbocharged producer gas engines designed originally for natural gas (NG) as the fuel. Producer gas, whose properties like stoichiometric ratio, calorific value, laminar flame speed, adiabatic flame temperature, and related parameters that differ from those of NG, is used as the fuel. Two engines having similar turbochargers are evaluated for performance. Detailed measurements on the mass flowrates of fuel and air, pressures and temperatures at various locations on the turbocharger were carried out. On both the engines, the pressure ratio across the compressor was measured to be 1.40 +/- 0.05 and the density ratio to be 1.35 +/- 0.05 across the turbocharger with after-cooler. Thermodynamic analysis of the data on both the engines suggests a compressor efficiency of 70 per cent. The specific energy consumption at the peak load is found to be 13.1 MJ/kWh with producer gas as the fuel. Compared with the naturally aspirated mode, the mass flow and the peak load in the turbocharged after-cooled condition increased by 35 per cent and 30 per cent, respectively. The pressure ratios obtained with the use of NG and producer gas are compared with corrected mass flow on the compressor map.

Adaptation of small capacity natural gas engine for producer gas operation

This article addresses the adaptation of a low-power natural gas engine for using producer gas as a fuel. The 5.9 L natural gas engine with a compression ratio of 10.5:1, rated at 55 kW shaft power, delivered 30 kW using producer gas as fuel in the naturally aspirated mode. Optimal ignition timing for peak power was found to be 20 degrees before top dead centre. Air-to-fuel ratio (A/F) was found to be 1.2 +/- 0.1 over a range of loads. Critical evaluation of the energy flows in the engine resulted in identifying losses and optimizing the engine cooling. The specific fuel consumption was found to be 1.2 +/- 0.1 kg of biomass per kilowatt hour. A reduction of 40 per cent in brake mean effective pressure was observed compared with natural gas operation. Governor response to load variations has been studied with respect to frequency recovery time. The study also attempts to adopt a turbocharger for higher power output. Preliminary results suggest a possibility of about 30 per cent increase in the output.

Experiments and zero D modeling studies using specific Wiebe coefficients for producer gas as fuel in spark-ignited engines

The paper addresses experiments and modeling studies on the use of producer gas, a bio-derived low energy content fuel in a spark-ignited engine. Producer gas, generated in situ, has thermo-physical properties different from those of fossil fuel(s). Experiments on naturally aspirated and turbo-charged engine operation and subsequent analysis of the cylinder pressure traces reveal significant differences in the heat release pattern within the cylinder compared with a typical fossil fuel. The heat release patterns for gasoline and producer gas compare well in the initial 50% but beyond this, producer gas combustion tends to be sluggish leading to an overall increase in the combustion duration. This is rather unexpected considering that producer gas with nearly 20% hydrogen has higher flame speeds than gasoline. The influence of hydrogen on the initial flame kernel development period and the combustion duration and hence on the overall heat release pattern is addressed. The significant deviations in the heat release profiles between conventional fuels and producer gas necessitates the estimation of producer gas-specific Wiebe coefficients. The experimental heat release profiles are used for estimating the Wiebe coefficients. Experimental evidence of lower fuel conversion efficiency based on the chemical and thermal analysis of the engine exhaust gas is used to arrive at the Wiebe coefficients. The efficiency factor a is found to be 2.4 while the shape factor m is estimated at 0.7 for 2% to 90% burn duration. The standard Wiebe coefficients for conventional fuels and fuel-specific coefficients for producer gas are used in a zero D model to predict the performance of a 6-cylinder gas engine under naturally aspirated and turbo-charged conditions. While simulation results with standard Wiebe coefficients result in excessive deviations from the experimental results, excellent match is observed when producer gas-specific coefficients are used. Predictions using the same coefficients on a 3-cylinder gas engine having different geometry and compression ratio(s) indicate close match with the experimental traces highlighting the versatility of the coefficients.

Selection and thermodynamic analysis of a turbocharger for a producer gas-fuelled multi-cylinder engine

The current work addresses the use of producer gas, a bio-derived gaseous alternative fuel, in engines designed for natural gas, derived from diesel engine frames. Impact of the use of producer gas on the general engine performance with specific focus on turbo-charging is addressed. The operation of a particular engine frame with diesel, natural gas and producer gas indicates that the peak load achieved is highest with diesel fuel (in compression ignition mode) followed by natural gas and producer gas (both in spark ignite mode). Detailed analysis of the engine power de-rating on fuelling with natural gas and producer gas indicates that the change in compression ratio (migration from compression to spark ignited mode), difference in mixture calorific value and turbocharger mismatch are the primary contributing factors. The largest de-rating occurs due to turbocharger mismatch. Turbocharger selection and optimization is identified as the strategy to recover the non-thermodynamic power loss, identified as the recovery potential (the loss due to mixture calorific value and turbocharger mismatch) on operating the engine with a fuel different from the base fuel. A turbocharged after-cooled six cylinder, 5.9 l, 90 kWe (diesel rating) engine (12.2 bar BMEP) is available commercially as a naturally aspirated natural gas engine delivering a peak load of 44.0 kWe (6.0 bar BMEP). The engine delivers a load of 27.3 kWe with producer gas under naturally aspirated mode. On charge boosting the engine with a turbocharger similar in configuration to the diesel engine turbocharger, the peak load delivered with producer gas is 36 kWe (4.8 bar BMEP) indicating a de-rating of about 60% over the baseline diesel mode. Estimation of knock limited peak load for producer gas-fuelled operation on the engine frame using a Wiebe function-based zero-dimensional code indicates a knock limited peak load of 76 kWe, indicating the potential to recover about 40 kWe. As a part of the recovery strategy, optimizing the ignition timing for maximum brake torque based on both spark sweep tests and established combustion descriptors and engine-turbocharger matching for producer gas-fuelled operation resulted in a knock limited peak load of 72.8 kWe (9.9 bar BMEP) at a compressor pressure ratio of 2.30. The de-rating of about 17.0 kWe compared to diesel rating is attributed to the reduction in compression ratio. With load recovery, the specific biomass consumption reduces from 1.2 kg/kWh to 1.0 kg/kWh, an improvement of over 16% while the engine thermal efficiency increases from 28% to 32%. The thermodynamic analysis of the compressor and the turbine indicates an isentropic efficiency of 74.5% and 73%, respectively.

ADAPTATION OF MW LEVEL NATURAL GAS LEAN BURN ENGINE FOR PRODUCER GAS OPERATION A GRID CONNECTED POWER PLANT

Availability of producer gas engines at MW being limited necessitates to adapt engine from natural gas operation. The present work focus on the development of necessary kit for adapting a 12 cylinder lean burn turbo-charged natural gas engine rated at 900 kWe (Waukesha make VHP5904LTD) to operate on producer and set up an appropriate capacity biomass gasification system for grid linked power generation in Thailand. The overall plant configuration had fuel processing, drying, reactor, cooling and cleaning system, water treatment, engine generator and power evacuation. The overall project is designed for evacuation of 1.5 MWe power to the state grid and had 2 gasification system with the above configuration and 3 engines. Two gasification system each designed for about 1100 kg/hr of woody biomass was connected to the engine using a producer gas carburetor for the necessary Air to fuel ratio control. In the use of PG to fuel IC engines, it has been recognized that the engine response will differ as compared to the response with conventional fueled operation due to the differences in the thermo-physical properties of PG. On fuelling a conventional engine with PG, power de-rating can be expected due to the lower calorific value (LCV), lower adiabatic flame temperature (AFT) and the lower than unity product to reactant more ratio. Further the A/F ratio for producer gas is about 1/10th that of natural gas and requires a different carburetor for engine operation. The research involved in developing a carburetor for varying load conditions. The patented carburetor is based on area ratio control, consisting of a zero pressure regulator and a separate gas and air line along with a mixing zone. The 95 litre engine at 1000 rpm has an electrical efficiency of 33.5 % with a heat input of 2.62 MW. Each engine had two carburetors designed for producer gas flow each capable of handling about 1200 m3/hr in order to provide similar engine heat input at a lower conversion efficiency. Cold flow studies simulating the engine carburetion system results showed that the A/F was maintained in the range of 1.3 +/- 0.1 over the entire flow range. Initially, the gasification system was tested using woody biomass and the gas composition was found to be CO 15 +/- 1.5 % H-2 22 +/- 2% CH4 2.2 +/- 0.5 CO2 11.25 +/- 1.4 % and rest N-2, with the calorific value in the range of 5.0 MJ/kg. After initial trials on the engine to fine tune the control system and adjust various engine operating parameter a peak load of 800 kWe was achieved, while a stable operating conditions was found to be at 750 kWe which is nearly 85 % of the natural gas rating. The specific fuel consumption was found to be 0.9 kg of biomass per kWh.

Fishermen cooperatives in the Green Revolution Programme

The aim of this study was to examine areas in which fishermen cooperatives can become involved and then suggest operational guidelines in order to increase fishermen income and also to make the Green Revolution Programme a success through increased production of fish. The paper enumerated different areas in which fishermen cooperatives can participate. These include: thrift and credits, thrift and savings, consumers and building cooperative societies. It is the belief of the author that the expansion of fishermen cooperatives into the areas mentioned in this paper can enable members to process and market their products more economically, buy supplies and equipment in large quantities and obtain lower cost credit

An appraisal of the current status of the fisheries of Eleiyele Reservoir by its fisheries cooperatives

In a study undertaken to evaluate the status of the fisheries of Eleiyele Reservoir (Nigeria) between 1995 and 1997, thermal stratification was observed to breakdown between December and March. Of the physico-chemical variables, transparency was positively correlated (p<0.05) with primary productivity, conductivity and dissolved oxygen concentration. Primary productivity ranged between 0.38mgC/m super(2)/d and 3.OmgC/ m super(2)/d, being lowest in April. BOD values ranged between 1.3mg-2.2mgO/l indicative of clean unpolluted water. Nine fish species belonging to the families Cichlidae, Centropomidae and Mochokidae were identified. Cichlids were the most abundant with Hemichromis species being predominant. Fishing was only carried out in the reservoir during the dry season months of November to April. Fish landing data for the reservoir, obtained from the Fisheries Division of the Ministry of Agriculture and Natural resources, Oyo State, in conjunction with comparative data from the Cooperative fishermen was low. It demonstrated a decreasing trend from January to April and during the period between 1985 and 1996, when compared with data collected in 1985 and 1986 from a previous similar study. Reasons for the low fish yield from the reservoir are discussed and compared with other Nigerian reservoirs

Do luxo ao lixo: uma análise da aplicabilidade e gestão da coleta seletiva solidária no âmbito de escolas públicas estaduais no Rio de Janeiro

Dos muitos problemas socioambientais, a geração e destinação de resíduos sólidos é um dos que mais afetam os agrupamentos humanos, principalmente nas grandes cidades. No Brasil, por um lado, políticas públicas vêm sendo implantadas, buscando encontrar soluções para tal problema. Por outro lado, acredita-se que a educação seja instrumento importante e necessário na organização social e na formação da cidadania. Dessa forma, este trabalho faz uma análise das ações necessárias e do processo de gestão para a coleta seletiva solidária em escolas públicas estaduais, pela aplicação do Decreto Estadual n. 40.645/07, o qual estabelece o descarte seletivo de materiais recicláveis nos órgãos públicos estaduais do Rio de Janeiro e sua destinação a grupos de catadores de recicláveis. Para isso, serviu-se da observação de um número pré-determinado de escolas localizadas no Grande Méier, na região metropolitana da cidade do Rio de Janeiro, e de cooperativas de catadores dessa mesma região. Nesse sentido, o presente trabalho parte de uma reflexão acerca da sociedade globalizada de produção e consumo, fazendo uma análise crítica da Política Nacional de Resíduos Sólidos (PNRS), tecendo um diálogo desta com a Política Nacional de Educação Ambiental (PNEA) e com o Código de Defesa do Consumidor (CDC), considerando a atividade de Coleta Seletiva Solidária (CSS) como proposta de política pública de inclusão social e interesse ambiental. Sendo assim, identifica dificuldades, possibilidades e conflitos inerentes à questão dos resíduos sólidos, associadas às questões do consumo.

Aquaculture technologies in Bangladesh: an assessment of technical and economic performance and producer behavior

This study evaluates the performance of a wide range of aquaculture systems in Bangladesh. It is by far the largest of its kind attempted to date. The purpose of this study was to identify and analyze the most important production systems, rather than to provide a nationally representative overview of the entire aquaculture sector of Bangladesh. As such, the study yields a huge amount of new information on production technologies that have never been thoroughly researched before. The study reveals an extremely diverse array of specialized, dynamic and rapidly evolving production technologies, adapted to a variety of market niches and local environmental conditions. This is a testament to the innovativeness of farmers and other value chain actors who have been the principal drivers of this development in Bangladesh. Data was collected from six geographical hubs. This survey was conducted from November 2011 to June 2012. Technological performance in terms of detailed input and output information, fish management practices, credit and marketing, and social and environmental issues were captured by the survey questionnaire, which had both open and closed format questions. The study generated insights that enable better understanding of aquaculture development in Bangladesh.

The value of cooperatives in rural electrification

The electricity sectors of many developing countries underwent substantial reforms during the 1980s and 1990s, driven by global agendas of privatization and liberalization. However, rural electrification offered little by way of market incentives for profit-seeking private companies and was often neglected. As a consequence, delivery models for rural electrification need to change. This paper will review the experiences of various rural electrification delivery models that have been established in developing countries, including concessionary models, dealership approaches and the strengthening of small and medium-sized energy businesses. It will use examples from the USA, Bangladesh and Nepal, together with a detailed case study of a Nepali rural electric cooperative, to explore the role that local cooperatives can play in extending electricity access. It is shown that although there is no magic bullet solution to deliver rural electrification, if offered appropriate financial and institutional support, socially orientated cooperative businesses can be a willing, efficient and effective means of extending and managing rural electricity services. It is expected that this paper will be of particular value to policy-makers, donors, project planners and implementers currently working in the field of rural electrification. © 2010 Elsevier Ltd.

The impact of saving and credit cooperatives on food security in the West Amhara Region of Ethiopia

In rural Ethiopia, among other things, lack of adequate financial service is considered as the basic problem to alleviate rural poverty and to solve the problem of food insecurity. Commercial banks are restricted to urban centres. Providing rural financial service through RUSACCO to the poor has been proposed as a tool for economic development and for achieving food security. Evidence from research in this regard has been so far scanty, especially in rural Ethiopia. The aims of this study are to analyze the determinants of membership, to identify socioeconomic and demographic factors that influence members’ participation in RUSACCOs and to quantify the impact of RUSACCOs on member households’ food security. The study was conducted in two purposely selected woredas in the Amhara region one from food insecure (Lay Gayint woreda) and the other from food secure (Dejen woreda). Six RUSACCOs were selected randomly from these two woredas. Both qualitative and quantitative data were collected. Key informant interviews, focus group discussions and survey techniques were used to collect primary data. Collected data was then analyzed using mixed methods depending on the nature of data. For quantitative data analysis appropriate statistical models were used. The study result reveals that the number of members in each RUSACCO is very small. However, the majority of non-member respondents are willing to join RUSACCO. Lack of information about the benefits of RUSACCO membership is the main problem why many rural poor do not join RUSACCOs. Members participate in different aspects of the cooperatives, starting from attending general assembly up to board membership. They also participate actively in saving and borrowing activities of RUSACCO. The majority of the respondents believe the RUSACCO is a vital instrument in combating food insecurity. The empirical findings indicate that gender, marital status, occupation, educational level, participation in local leadership and participation in other income generation means determine the decision of rural poor to join a RUSACCO or not. The amount of saving is determined by household head occupation, farming experience and income level. While age of household head, primary occupation, farming experience, date of membership, annual total consumption expenditure, amount of saving and participation in other income generation activities influence members’ amount of borrowing by RUSACCO members. Finally, the study confirms that RUSACCO participation improves household food security. RUSACCO membership has made positive impact on household total consumption expenditure and food expenditure.

Genome sequence of Rhodococcus sp. strain PML026, a trehalolipid biosurfactant producer and biodegrader of oil and alkanes

Rhodococcus sp. strain PML026 produces an array of trehalolipid biosurfactant compounds in order to utilize hydrophobic carbon sources, such as oils and alkanes. Here, we report the high-quality draft genome sequence of this strain, which has a total length of 5,168,404 bp containing 4,835 protein-coding sequences, 12 rRNAs, and 45 tRNAs.

The sector of olive-oil cooperatives and the use of ICT: A comparative study regarding othe legal forms

The current global environment and the general increase in the spread and use of Information Technology and Communication (ICT) by companies and consumers, make the use of these technologies as essential to confront the growing competition in the market. Focused on this sector, in this research we analyze the use of electronic commerce, as through websites as through electronic markets, and the use of social networking tools as enablers of business. For this aim, we conducted a comparative analysis between the Andalusian olive oil cooperatives and other legal forms which are present in the sector.

Social economy and economic crisis in the basque country abstract

This article examines the socio-economic evolution of the social economy sector in the Basque Country during the 2008-2014 period of economic crisis. Data have been obtained within a framework of collaboration between university, Basque Government and private sector of the social economy. The results suggest that such entities have evolved better, both in terms of number of enterprises and employment, than the general economy of the Basque Country, while the context of public policies aimed at social economy has worsened over the years. However, in economic terms (measured through the Gross Value Added generated), they have not been able to cope with the crisis in equal conditions to the general economy. The main contribution of this research lies in that, unlike similar studies, it discusses the evolution of the whole sector of the social economy, taking as reference a broad period of the current economic crisis.