Study on a novel polyimide precursor prepared by a modified polymerization of monomeric reactants (MPMR) procedure

A novel polyimide precursor based on the dimethyl ester of 3,3',4,4'-biphenyltetracarboxylic acid, 4,4'-methylene dianiline and the monomethyl ester of 5-norbornene-2,3-dicarboxylic acid (BPDE/MDA/NE) was prepared by a modified polymerization of monomeric reactants (PMR) approach (MPMR). The composition of the precursor was quantitatively characterized by means of FTIR, HPLC and GC. The fractions of imide, amic ester and amic acid units in the precursor, typically prepared by refluxing in 1,4-dioxane for 2 h, were 33.7, 30.8 and 1.1 mol-%, respectively. The portion of free MDA was 3.34 wt.-% as determined by HPLC.

Thermal influence on excimer-laser-induced electrical conductivity on polyimide film surfaces

The thermal influence on the electrical conductivity of polyimide film surfaces induced by KrF-laser irradiation was investigated, The formation of conducting phases was demonstrated to be highly temperature sensitive, as evidenced by strong dependence of the electrical conductivity on repetition rate and ambient temperature. XPS and Raman studies showed that the efficiency of the formation of conducting phases could be enhanced by the increase of temperature on irradiated polyimide film surfaces. After the disruption of polymeric chain, the carbon-enriched clusters remained on the irradiated polyimide film surfaces organized into polycrystalline graphite-like clusters responsible for electrical conductivity. The resulting dangling bonds from the decomposition process of polyimide acted as centers for the rearrangement of carbon-enriched clusters. It is suggested that the motion of radicals was promoted with increasing the temperature. Therefore the formation of polycrystalline graphite-like clusters benefited from high remaining temperature on the irradiated polyimide film surfaces. These results revealed that thermal influence played a dominant role on the formation of conducting phases.

Structural studies of excimer laser-induced percolative phase transition on polyimide thin film surfaces

The behavior of electrical conductivity for excimer laser irradiated polyimide films in the vicinity of the critical number of laser shots was described by three-dimensional percolative phase transition model. It is: found that electrical conductivity changed more rapidly than that predicted by the percolation model. Thus, the change in microstructure with increasing number of laser shots was analyzed by FT-IR Raman spectrometry and laser desorption time-of-flight mass spectrometry. It is demonstrated that not only the number but also the average size of graphite particles on the irradiated polyimide film surfaces increased with increasing number of laser shots. These results were helpful to better understand the critical change in electrical conductivity on the irradiated polyimide film surfaces. (C) 2001 Elsevier Science B.V. All rights reserved.

Diffusion-limited kinetics modeling of one-step polyimide formation

A diffusion-limited kinetic model was developed to describe the imidization of one-step polythioetherimide formation based on an endgroup diffusion model. The changes of conversion and viscosity during the imidization were monitored with thermogravimetric analysis and dynamic stress rheometry, respectively. It was observed that the imidization rate began to decelerate after a fast early stage, whereas the viscosity in the system increased dramatically after a period of low value. Amic acid and imide formations concurrently take place in the one-step polyimide formation, but the formation of amic acid is much slower than that of imide and is the rate-limiting step of imidization. When a second-order kinetic model was used to describe the imidization, the effect of viscosity on the diffusion resistance of reactive groups needed to be included. In order to predict the change of viscosity during the imidization, the Lipshitz-Macosko model was modified and introduced into the diffusion-limited kinetic model by the Stokes-Einstein equation. The comparison of the modeled results with experimental data indicated that the diffusion-limited kinetic model and the modified Lipshitz-Macosko model were able to efficiently predict the changes of conversion and viscosity with temperature and time during the one-step polythioetherimide formation. (C) 2001 John Wiley & Sons, Inc.

Preparation of polyimide-BaTiO3 hybrid films by a dispersion process and their microstructure

Barium titanate (BaTiO3) powders with particle sizes of 30 similar to 50 nm were prepared from barium stearate, titanium alkoxides and stearic acid by stearic acid-gel method. Dispersing the agglomerate of BaTiO3 nanoparticles into poly(amic acid) solution followed by curing led to the formation of polyimide hybrid films. The hybrid films were transparent and well distributed with BaTiO3 nanoparticles when the BaTiO3 content was less than 1 wt%. Highly loaded hybrid film containing 30 wit % BaTiO3 was tough, had a smooth surface and possessed much higher dielectric and piezoelectric constants than the parent polyimide.

Ester-type precursor of polyimide and photosensitivity

In order to investigate the influence of the main chain structure and molecular weight on the sensitivity of photosensitive ester-type precursor of polyimide (photo-PAE), an improved method was used to synthesize several kinds of photo-PAEs with relatively high molecular weight. Their sensitivities (at 365 nm) were investigated, and it was found that some additives such as sensitizer and photoinitiator had the greatest influence on the sensitivity of photo-PAE, that the photo-PAE with BPDA and mPDA as the main chain structure had the best sensitivity (D-0.5: 5-10 mJ/cm(2)) among the studied photo-PAEs, and that the sensitivity did not significantly change with the change of inherent viscosity of photo-PAE. Meanwhile, the thermal imidization of these photo-PAEs was also investigated by means of TGA and IR analyses. Additionally, a discussion was made for formulation of PSPI resist. (C) 1999 Elsevier Science Ltd. All rights reserved.

New optically active aromatic polyimides II: Synthesis and properties of optically active aromatic polyimide based on (R)-(+)-2,2 '-bis(2-trifluoro-4-aminophenoxy)-1,1 '-binaphthyl

Optically active (R)-(+)-2, 2'-bis(2-trifluoro-4-aminophenoxy)-1, 1'-binaphthyl was prepared from 1, 1'-bi-2-naphthol. The optically active aromatic polyimide was also successfully synthesized. This new polymer has good solubility, thermal stability etc. Its specific rotation was found to be +174 degrees, and its chiroptical property was also studied.

Fluorescence and aggregation behavior of a polyimide in solutions

The UV-visible absorption and fluorescence spectra of a soluble polyimide, YS-30, in several organic solvents were measured over a wide range of concentration. The experimental results show that there exist both intramolecular and intermolecular electron donor acceptor interactions for YS-30 molecules. The fluorescence behavior of YS-30 in N,N-dimethylacetamide and in chloroform solutions is similar in general, except that its ground-state intermolecular charge transfer emission is more obvious in N,N-dimethylacetamide solution. This difference is attributed to the greater extent of disruption of the chain packing by solvent or/and the more efficient radiationless energy dissipation process from the excited state complexes to chloroform. The intensity ratio of intermolecular charge transfer emission to intramolecular charge transfer emission is used to characterize the state of aggregation of YS-30 molecules in solutions. The plot of this ratio versus concentration indicates the existence of two critical concentrations. It is also found from the same plot that the decrease of coil size is very pronounced during the initial stage of shrinkage.

A comparative study of insoluble and soluble polyimide thin films

Physical properties of thin films of soluble and insoluble aromatic polyimides were compared by d.s.c., u.v.-visible and fluorescence spectroscopy, and prism coupler technique. D.s.c. results showed that the thermal properties of insoluble polyimides are superior to those of soluble ones, owing to the specific molecular interactions of insoluble polyimides, revealed by fluorescence spectroscopy. However, the specific molecular interactions sacrifice the transparency in their thin films, shown by u.v.-visible transmission spectra. Negative birefringence of thin films, not only for soluble polimides but also for polyamic acids of insoluble polyimides, was confirmed by prism coupler, while thin films of insoluble polyimides thermally imidized lack high levels of negative birefringence. It is regarded that thin films of insoluble polyimides thermally imidized are likely to be isotropic because of molecular relaxation above their glass transition temperatures (T-g) in the course of thermal imidization, according to Flory's principle. On the contrary, thin films of insoluble poyimide chemically imidized keep the same levels of negative birefringence as those of the relevant polyamic acid thin films. Judging from the opposite cases, it is recognized that molecular relaxation above T-g weakens the optical anisotropy of polyimide thin films. (C) 1998 Elsevier Science Ltd. All rights reserved.

Polyimide structure-property relationships - I. Polyimide properties vs dianhydride configuration

X-ray crystal structures of 2,2',3,3'-and 3,3',4,4'-biphenyltetracarboxylic dianhydride (2,2',3,3'- and 3,3',4,4'-BPDA) were determined. The dianhydride isomers have different symmetry caused by difference in two anhydride group positions and the dihedral angles between the two phenyl rings are 62.9 degrees for 2,2',3,3',-BPDA and 0 degrees for 3,3',4,4'-BPDA respectively. The polyimides from 2,2',3,3'-BPDA exhibit enhanced solubility, higher thermal stability, and higher glass transition temperature (T-g) compared with those from 3,3',4,4'-BPDA.

Optical properties of organo-soluble polyimide thin films and their applications in liquid crystal displays

Three organo-soluble polyimide powders have been synthesized. Their imidization was verified by Fourier transform infrared (FTIR) and thermal gravimetric analysis (TGA) techniques. The amorphous morphology of their thin films were confirmed by X-ray diffraction. Polyimide thin films were prepared by solution casting or spin coating. UV-visible transmission spectra of thin films revealed that they are almost transparent in the range of visible light. With in-plane orientation, revealed by FTIR spectra, negative birefringence (Delta n) of thin films were observed, and refractive indices of the thin films along the film plane (n(TE)) and normal to the plane (n(TM)) were measured by a prism coupler. Because of negative birefringence of the thin films, they tan be substituted for the compensation films for twisted nematic liquid crystal displays (TN-LCDs) to extend their viewing angles. In this paper, a 90 degrees C TN-LCD and 120 degrees C TN-LCD were taken as examples to show the compensation effect of thin films of a qualified polyimide. (C) 1998 Elsevier Science S.A. All rights reserved.

Chain conformation of a high-performance polyimide in organic solution

An organo-soluble polyimide based on 1,4-bis(3,4-dicarboxyphenoxy) benzene dianhydride (HQDPA) and 2,2'dimethyl-4,4'-methylene dianiline (DMMDA), was synthesized via two-step polycondensation accompanied by chemical imidization. Five fractions were prepared by fractionation. The dilute solutions of the fractions were studied by LLS (Laser Light Scattering) and the intrinsic viscosities of the fractions were measured. The unperturbed dimension was determined by the intrinsic viscosity with the Stockmayer-Fox equation. The results indicate that the polyimide in this study has a flexible chain conformation in chloroform and N,N-dimethyl acetamide (DMAc). However, the degree of chain expansion differs in different solvents. (C) 1998 Published by Elsevier Science Ltd. All rights reserved.

Optical anisotropy of flexible polyimide thin films

Optical anisotropy of thin films of an organo-soluble flexible polyimide based on 1,4-bis(3,4-dicarboxyphenoxy) benzene dianhydride (HQDPA) and 2,2-dimethyl-4,4'-methylene dianiline (DMMDA) was detected by a prism-coupler technique. A mechanism is proposed, based on the model of gel film collapse. The degrees of optical anisotropy of the thin films were evaluated via the level of negative birefringence. The residual solvent in the films lessens the levels of negative birefringence so that the residual solvent must be evacuated. The levels of negative birefringence are independent on the solid content of the initial solution, but dependent on the thickness of the films. For a film of 16 mu m thick, zero birefringence was achieved, postulated from the dependence of negative birefringence on the thickness of thin films. The relationship between the optical anisotropy and solution properties shows that the degrees of optical anisotropy of thin films on the same scale of thickness depend on macromolecular sizes in their dilute solutions.

Characteristics of the conductive polyimide film surfaces induced by ultraviolet laser beam

A conducting layer with the conductivity of 1.2 Omega(-1)cm(-1) stripped in a solvent from KrF-laser-irradiated polyimide thin film is taken as a sample to determine the microstructure of the conducting layer. Fourier-transform infrared and X-ray photoelectron spectroscopies show the formation of the carbon-rich clusters after irradiation. The element analysis gives the atomic ratio of C:H:N:O for the carbon-rich cluster as 60:20:3:1. Wide-angle X-ray diffraction indicates that the conducting layer is mainly amorphous carbon with a small amount of the short-range ordered carbon-rich clusters. This study suggests a structural model with three-layer carbon sheets linked together in a random fashion for the short-range ordered carbon-rich clusters. The interplanar spacing is 3.87 Angstrom and the layer diameter 25 Angstrom. The transport model of variable-range hopping in three dimensions is used to explain the conducting behavior of the conducting layer. In our case, the short-range ordered carbon-rich clusters are assumed to be conducting islands dispersed in the amorphous carbon-rich cluster matrix.

Gas separation with organo-soluble high performance aromatic polyimide films

An organo-soluble polyimide based on 4,4'-(1,4-phenylenedioxy)diphthalic anhydride and 2,2'-dimethyl-4,4'-methylenedianiline was synthesized by two-step polycondensation accompanied by chemical imidization. Polyimide films were prepared by spray casting onto glass substrates. The study focused on the separation of carbon dioxide (CO2) from natural gas and the enrichment of methane (CH4) from butane (C4H18). The permeability and permselectivity coefficients of these gases were determined.