Some considerations about a new procedure to derive transmission line parameters concerning three-phase lines

The paper shows an alternative methodology to calculate transmission line parameters per unit length and to apply it in a three-phase line with a vertical symmetry plane. This procedure is derived from a general procedure where the modal transformation matrix of the line is required. In this paper, the unknown modal transformation matrix requested by general procedure is substituted by Clarke's matrix. With the substitution that is shown in the paper, the transmission line parameters can be obtained starting from impedances measured in one terminal of the line. First, the article shows the classical methodology to calculate frequency dependent transmission line parameters by using Carson and Pollaczeck's equations for representing the ground effect and Bessel's functions to represent the skin effect. After that, a new procedure is shown to calculate frequency dependent transmission line parameters directly from currents and voltages of an existing line. Then, this procedure is applied in a non-transposed three-phase transmission line whose parameters have been previously calculated by using the classical methodology. Finally, the results obtained by using the new procedure and by using the classical methodology are compared. The article shows simulation results for typical frequency spectra of switching transients (10 Hz to 10 kHz). Results have shown that procedure has © 2006 IEEE.

Vortices in the extended Skyrme-Faddeev model

We construct analytical and numerical vortex solutions for an extended Skyrme-Faddeev model in a (3 + 1) dimensional Minkowski space-time. The extension is obtained by adding to the Lagrangian a quartic term, which is the square of the kinetic term, and a potential which breaks the SO(3) symmetry down to SO(2). The construction makes use of an ansatz, invariant under the joint action of the internal SO(2) and three commuting U(1) subgroups of the Poincare group, and which reduces the equations of motion to an ordinary differential equation for a profile function depending on the distance to the x(3) axis. The vortices have finite energy per unit length, and have waves propagating along them with the speed of light. The analytical vortices are obtained for a special choice of potentials, and the numerical ones are constructed using the successive over relaxation method for more general potentials. The spectrum of solutions is analyzed in detail, especially its dependence upon special combinations of coupling constants.

Respuesta fisiológica y agronómica del olivar en seto (cv. Arbequina) a la orientación de filas y al ancho de calle: relación entre la producción y calidad del aceite y la radiación interceptada

En las últimas dos décadas, los productores han plantado olivares en seto para lograr la mecanización de la poda y en especial de la cosecha, reducir los costes de mano de obra y permitir intervenciones de manejo rápidas y oportunas. Los olivares se desarrollaron en ausencia del conocimiento científico, sobre el diseño óptimo de la estructura de la copa, necesario para incrementar la producción y calidad del aceite. En contraste, con los árboles muy espaciados y distribuidos uniformemente de las plantaciones tradicionales, en el olivar en seto hay una marcada variabilidad espacial y temporal de la radiación disponible en función del diseño de la plantación. Así, conocer la respuesta fisiológica y productiva del olivo a la radiación resulta fundamental en el olivar en seto. La orientación de las filas y el ancho de calle son aspectos que se deciden en el diseño de las plantaciones en seto. Ambos aspectos modifican la radiación interceptada por la canopia y, por lo tanto, pueden incidir en la productividad y calidad del aceite. Una vez realizada la plantación no pueden ser modificados, y así las ventajas o desventajas permanecerán fijas durante toda la vida productiva del olivar. A pesar de esto, el impacto de la orientación de las filas y el ancho de calle han recibido poca atención en olivos y en la mayoría de los frutales conducidos en seto. Por todo ello, los objetivos principales de esta tesis fueron, (i) evaluar el efecto de la orientación del seto y del ancho de calle, sobre la productividad y calidad del aceite, (ii) evaluar un modelo que estime la radiación dentro de la canopia. Este modelo permitirá cuantificar las relaciones entre la radiación y los componentes del rendimiento y calidad del aceite de olivares en setos con un amplio rango de estructuras y (iii) conocer la variabilidad en las características de las hojas (morfológicas y fisiológicas) y de los tejidos del fruto (tamaño y composición) en diferentes posiciones de la copa de los setos. Para ello, se dispuso de 3 ensayos de olivar en seto (cv. Arbequina) implantados en 2008 en el municipio de La Puebla de Montalbán, Toledo. La primera cosecha fue en 2010 y a partir del 2012 los setos formaron una copa continua. A partir de ese año, los setos se mantuvieron mediante poda, con similar ancho (~1 m) y altura (~2,5 m), acordes a las dimensiones de la cosechadora vendimiadora. En los años 2012 y 2013 se estudió en profundidad la respuesta de las plantas de estos ensayos. En el ensayo 1, los setos fueron plantados con cuatro orientaciones de filas: N–S, NE–SO, NO–SE y E–O y el mismo ancho de calle (4 m). En los otros dos ensayos, los setos fueron plantados con tres anchos de calle (5,0, 4,0 y 2,5 m), y con filas orientadas N–S (ensayo 2) y E–O (ensayo 3). La respuesta de la orientación de las filas se evaluó a nivel de seto y de estratos del seto (alturas y caras), a través de mediciones del crecimiento de brotes, componentes reproductivos, características y temperatura del fruto, estado hídrico del suelo y de las plantas, fotosíntesis neta de las hojas y contenido de ácidos grasos. Los setos orientados NE–SO (2,7 t/ha) lograron la mayor producción de aceite, que fue significativamente más alta que la de los setos E–O (2,3 t/ha). La producción de aceite de los setos E–O no se diferenció estadísticamente de los setos N–S (2,5 t/ha). Las diferencias productivas entre orientaciones fueron explicadas por el número de frutos en cosecha, a su vez la variación en el número de frutos estuvo asociada al efecto de la orientación de las filas sobre el número de yemas desarrolladas y el porcentaje de inflorescencias fértiles. Las hojas en las caras iluminadas de los setos NE–SO y N–S presentaron mayor tasa fotosintética a la mañana (~10.0 h) que los setos E–O, en el año 2012, pero no en 2013. La orientación de las filas no tuvo un efecto significativo en el contenido de ácidos grasos de los aceites extraídos, esto ocurrió a pesar de variaciones en la temperatura interna de los frutos (3 °C) y de la radiación (40%) entre las distintas caras de los setos. La orientación del seto afectó significativamente al contenido relativo de agua del suelo, donde setos E–O presentaron valores más altos (12%) que setos N–S durante el verano y otoño. Sin embargo, el potencial hídrico de tallo fue similar entre orientaciones. En los ensayos 2 y 3, se evaluó el efecto que produce, a nivel de seto y de estratos (caras y alturas), reducir el ancho de calle de 5,0 a 4,0 y 2,5 m, en un seto orientado N–S y otro E–O, respectivamente. La relación entre altura/ancho de calle libre aumentó 0,6 a 0,8 y 1,6, al reducir 5,0, 4,0 y 2,5 m el ancho de calle, mientras la longitud de seto y el volumen de copa por hectárea incrementó 100% al reducir de 5,0 a 2,5 m, el ancho de calle. En los setos orientados N–S, la producción de aceite por ha acumulada en 4 campañas, incrementó significativamente un 52 %, al reducir de 5,0 a 2,5 m el ancho de calle. Los setos N–S con calle más estrecha (2,5 m) tuvieron un 19% menos frutos que los setos con calle más ancha (5,0 m) y a su vez el 60% de los mismos se localizaron los estratos altos de la canopia de los setos con calles estrecha en comparación al 40% en setos con calle de 5,0 m. En los estratos más bajos de los setos con calles de 2,5m hubo menor crecimiento de los brotes y los frutos tuvieron menor peso seco, contenido de aceite y madurez, que los frutos en los estratos bajos de los setos a 5,0 m. Los componentes del rendimiento y características de los frutos (agua y madurez) fueron similares entre la caras E y O, independientemente del ancho de calle. En los setos orientados E–O, la producción de aceite por ha acumulada en 4 campañas, no respondió significativamente al ancho de calle, debido a una disminución significativa en el número de frutos y producción de aceite por m de seto, al reducir de 5,0 a 2,5 m, el ancho de calle. En los setos orientados E–O, con calles de 5,0 m, los frutos presentaron similar peso seco, contenido de aceite y agua, en las caras S y N, sin embargo, cuando la calle fue reducida a 2,5, los frutos de la cara S fueron más pesado y maduros que en la cara N. Independientemente del ancho de calle y de la orientación del seto, el aceite presentó mayor contenido de ácidos palmitoleico, palmítico, esteárico y linoleico en los frutos del estrato más alto de la canopia disminuyendo hacia la base. En contraste, el contenido de ácido oleico aumentó desde el estrato más alto hacia la base de los setos. Las diferencias en el contenido de ácidos grasos entre la parte alta y baja de los setos, incrementó al reducir el ancho de calle en los setos N–S, pero no en los E-O. En conclusión, en olivares en seto, reducir el ancho de calle permite incrementar la producción de aceite, en setos orientados N–S, pero no en E–O. Un modelo que estima la cantidad y distribución de la radiación en toda la copa del seto, fue utilizado para estimar la radiación interceptada en distintos estratos del seto. El modelo requiere un valor del coeficiente de extinción (k) para estimar la transmisión de radiación a través de la copa, el cual fue obtenido experimentalmente (k=1,2). Utilizando los datos del ensayo 1, un único modelo lineal relacionó el peso seco y el rendimiento graso de setos con la radiación interceptada por los distintos estratos de setos con cuatro orientaciones de filas. La densidad de frutos fue también relacionada con la radiación, pero más débilmente. En los setos orientados N–S, plantados con tres anchos de calles, (ensayo 2) el contenido de ácidos palmitoleico y linoleico del aceite incrementó linealmente con el incremento de la radiación interceptada, mientras el contenido ácido oleico disminuyó linealmente con el incremento de la radiación. El contenido de ácidos grasos del aceite no estuvo relacionado con la radiación interceptada en setos orientados E–O (Ensayo 3). En los setos N–S y E–O, plantados con anchos de calle de 2,5 m, se estudiaron las interacciones entre la radiación y características de las hojas, número de fruto, tamaño y composición de los frutos a nivel de órgano, tejido y células. Independientemente de la orientación del seto, el área y el contenido de clorofila de las hojas incrementaron significativamente en los estratos más bajos de los setos. Mientras, las hojas de los estratos medios del seto presentaron mayor capacidad fotosintética que en los estratos bajos y alto de los setos. Los estratos del seto que interceptaron más radiación produjeron frutos con mayor tamaño y contenido de aceite en el mesocarpo, sin efectos sobre el tamaño y composición del endocarpo. A nivel celular, los frutos expuestos a mayor nivel de radiación desarrollaron en el mesocarpo células de mayor tamaño en comparación a frutos menos expuestos, mientras el número de células no fue afectado. Adicionalmente, el número y tamaño de las células estuvo relacionado con la composición del mesocarpo en términos de aceite, agua y peso seco menos aceite. Esta tesis, contribuye, desde una perspectiva integral del cultivo del olivo, a cuantificar el impacto de la orientación y ancho de calle sobre la producción y calidad del aceite en olivares conducidos en setos. El análisis y discusión de la relación entre la radiación y los componentes del rendimiento y calidad del aceite, puede ayudar a diseñar plantaciones en seto con dimensiones óptimas para la intercepción de la radiación. ABSTRACT In the last two decades, olive hedgerow system has been established by commercial growers to allow continuous mechanized pruning and especially harvest, reduce costs of manual labour and allow more rapid and timely management interventions. The adoption of hedgerow was done in the absence of adequate scientific knowledge of the impact of this orchard structure and associated mechanization on tree response, yield and quality, after centuries in low-density orchards and open-formed trees. The row orientation and width alley are fundamental aspects in the hedgerow design and have been scarcely studied in olive. Both aspects modify the radiation intercepted by the canopy, and consequently the productivity and oil quality, and once defined in orchard planting cannot be changed, so advantages and disadvantages remain fixed for the lifespan of the orchard. The main objectives of this thesis were to (i) evaluate the impact of the row orientation and width alley on productivity and oil quality by the measurements of profile of the determining processes of shoot growth, fruit temperature, yield components and fruit and oil characteristics on opposite sides of olive hedgerows. Additionally, the effect of row orientation on the plant water status was also evaluated; (ii) evaluate a mathematical model for estimating the radiation within the canopy and quantify the relationships between the radiation estimated and yield components and oil quality in olive hedgerows under wide range of structures and; (iii) determine the variability in the characteristics of the leaves (morphological and physiological) and fruit tissues (size and composition) in different positions of the hedgerows canopy. Three plots of olive hedgerows (cv. Arbequina) planted in 2008 in La Puebla de Montalbán, Toledo were evaluated during the 2012 and 2013 seasons. The hedgerows were maintained by lateral pruning and topping with the same width (1 m) and height (2.5 m) compatible with the intended harvester. In a plot (experiment 1), the hedgerows were planted with the same width alley (4 m) and four row orientations: N–S, NE–SW, NW–SE and E–W. Other two plots (Experiments 2 and 3) separated by approximately 100 m were planted with N–S and E–O oriented rows and three alley widths in each orientation: 5.0, 4.0 and 2.5 m. In the exp. 1, maximum fruit yield were achieved by NE–SW and NW–SW (15.7 t/ha). Of these, NE–SW achieved the highest oil yield (2.7 t/ha). There were no differences in fruit or oil yield between N–S (2.5 t oil/ha) and E–W (2.3 t oil/ha) orientations. Fruit number was the most important component to explain these differences, by previous influence on number of bud developed and percentage of fertile inflorescences. Fruit maturity and oil quality on both sides of the hedgerows were not affected by row orientation. This occurred despite significant variations in the internal fruit temperature, which was closely related to the irradiance received by the canopy and the time of day. Additionally, row orientation significantly affected the relative water content of the soil, where E–W oriented hedgerows showed consistently higher values than N–S during summer-autumn season. The stem water potential at midday, however, was similar between orientations, revealing possible lower water consumption of E–W than N–S oriented hedgerows. In the exp. 2, regardless of row orientation, reduction of row spacing from 5.0 to 4.0 and 2.5 m increases the ratio of canopy depth to free alley width (Al/An) from 0.6 to 0.8 and 1.6, respectively, and ads 25 and 100 % more hedgerow length per ha. In N–S oriented hedgerows, oil production per ha increased significantly by 14 and 52 % in 4.0 m and 2.5 m relative to 5.0 m row spacing, the effect being proportionally less than the increase in hedgerow length per ha. Hedgerows spaced 2.5 m with Al/An = 1.6 produced relatively fewer fruits per unit length than did wider spacings and were preferentially distributed in upper layers. Fruits located at the bottom of the canopy were smaller, with lower oil content and were less mature. In E–W oriented hedgerows, oil production per ha did not respond significantly to row spacing, despite the doubling of row length from the 5.0 to the 2.5 m row spacing. The explanation was found in fewer fruit per unit length of hedgerow and smaller oil content at 2.5 m than 5.0 m row spacing, averaged over the experimental period. In E–W hedgerows spaced at 5.0 m with Al/An = 0.6, the vertical profiles of fruit characteristics (mass, oil and water contents, and maturity) were similar between opposing sides, but at 4.0 m (Al/An= 0.8) and 2.5 m (Al/An=1.6) spacings, fruits on the S side were heavier and more mature than on N side. The oil extracted from fruits harvested at different heights of N–S and E–W oriented hedgerows showed higher palmitoleic, palmitic, stearic and linoleic contents at the canopy top decreasing toward base. The oleic content was reverse, increased from top to base. In N–S hedgerows, vertical gradients increased by reducing the alley width, but not in the E–W oriented hedgerows. The simulation of internal canopy irradiance was related in a single relationship (R2 = 0.63) to the vertical profiles of fruit weight and oil content of olive hedgerows with wide range of structures. The density of fruits was also associated with the irradiance but more weakly (R2 = 0.27), and revealed a more complex response involving changes in the vegetative structure by canopy management (topping) and the effect of radiation on the previous sequence that defines the number of fruits. The vertical profiles of oil quality traits were closely associated to canopy irradiance, but only when the N–S oriented hedgerows were considered. The contents of palmitoleic and linoleic acid in the oil increased linearly when intercepted irradiance increased from 9 to 19 mol PAR/m2. In contrast, oleic content decreased linearly in this irradiance range. Additionally, we advanced knowledge regarding the interactions among irradiance and leaf, fruit number, size and composition at organ-, tissue- and cellular- levels. The irradiance received at different positions in the canopy strongly affected the leaf area and chlorophyll content, and mesocarp size and composition (water and oil), without effects on endocarp size and composition. At the cellular level, light-exposed fruit developed larger mesocarp cells than shaded fruits, but cell number was not affected. Our results indicate that cell number and size are related to mesocarp composition in term of oil, water, and dry weight menus oil, although the specific manner in which they interact remains to be determined. This research contributes from an integral perspective of olive growing to quantify the impact of row orientation and width alley on productivity and oil quality in hedgerows systems. The analysis and discussion of the relationships between radiation and yield components and oil quality can help understand the impact of design olive hedgerows in general and in a wide range of environmental conditions.

Investigation of particle identification methods for the analysis of the photoproduction of neutral kaons on a liquid deuterium target

The Photoproduction of neutral kaons off a deuteron target has been investigated at the Tohoku University Laboratory of Nuclear Science. The PID methods investigated incorporated a combination of momentum, velocity (β=v/c), and energy deposition per unit length (dE/dx) measurements. The analysis demonstrates that energy deposition and time of flight are exceedingly useful. A higher signal to background ratio was achieved for hard cuts in combination. A probabilistic likelihood estimation approach (LE) as a method for PID was also explored. The probability of a particle being correctly identified by this LE method and the preliminary results denote the need for highly precise limitations on the distributions from which the parameters would be extracted. It was confirmed that these PID are applicable approaches to properly identify pions for the analysis of this experiment. However, the background evident in the mass spectra points to the need for a higher level of proton identification.

Desenvolvimento de uma bancada para a realização de ensaios de auto-amortecimento em cabos condutores de energia elétrica

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Mecânica, 2015.

High performance terahertz resonant tunnelling diode sources and broadband antenna for air-side radiation

Resonant tunnelling diode (RTD) is known to be the fastest electronics device that can be fabricated in compact form and operate at room temperature with potential oscillation frequency up to 2.5 THz. The RTD device consists of a narrow band gap quantum well layer sandwiched between two thin wide band gap barriers layers. It exhibits negative differential resistance (NDR) region in its current-voltage (I-V) characteristics which is utilised in making oscillators. Up to date, the main challenge is producing high output power at high frequencies in particular. Although oscillation frequencies of ~ 2 THz have been already reported, the output power is in the range of micro-Watts. This thesis describes the systematic work on the design, fabrication, and characterisation of RTD-based oscillators in microwave/millimetre-wave monolithic integrated circuits (MMIC) form that can produce high output power and high oscillation frequency at the same time. Different MMIC RTD oscillator topologies were designed, fabricated, and characterised in this project which include: single RTD oscillator which employs one RTD device, double RTDs oscillator which employs two RTD devices connected in parallel, and coupled RTD oscillators which combine the powers of two oscillators over a single load, based on mutual coupling and which can employ up to four RTD devices. All oscillators employed relatively large size RTD devices for high power operation. The main challenge was to realise high oscillation frequency (~ 300 GHz) in MMIC form with the employed large sized RTD devices. To achieve this aim, proper designs of passive structures that can provide small values of resonating inductances were essential. These resonating inductance structures included shorted coplanar wave guide (CPW) and shorted microstrip transmission lines of low characteristics impedances Zo. Shorted transmission line of lower Zo has lower inductance per unit length. Thus, the geometrical dimensions would be relatively large and facilitate fabrication by low cost photolithography. A series of oscillators with oscillation frequencies in the J-band (220 – 325 GHz) range and output powers from 0.2 – 1.1 mW have been achieved in this project, and all were fabricated using photolithography. Theoretical estimation showed that higher oscillation frequencies (> 1 THz) can be achieved with the proposed MMIC RTD oscillators design in this project using photolithography with expected high power operation. Besides MMIC RTD oscillators, reported planar antennas for RTD-based oscillators were critically reviewed and the main challenges in designing high performance integrated antennas on large dielectric constant substrates are discussed in this thesis. A novel antenna was designed, simulated, fabricated, and characterised in this project. It was a bow-tie antenna with a tuning stub that has very wide bandwidth across the J-band. The antenna was diced and mounted on a reflector ground plane to alleviate the effect of the large dielectric constant substrate (InP) and radiates upwards to the air-side direction. The antenna was also investigated for integration with the all types of oscillators realised in this project. One port and two port antennas were designed, simulated, fabricated, and characterised and showed the suitability of integration with the single/double oscillator layout and the coupled oscillator layout, respectively.

Functional specialization of Eucalyptus fine roots: contrasting potential uptake rates for nitrogen, potassium and calcium tracers at varying soil depths

1. Little is known about the role of deep roots in the nutrition of forest trees and their ability to provide a safety-net service taking up nutrients leached from the topsoil. 2. To address this issue, we studied the potential uptake of N, K and Ca by Eucalyptus grandis trees (6 years of age - 25 m mean height), in Brazil, as a function of soil depth, texture and water content. We injected NO(3)(-)- (15)N, Rb(+) (analogue of K(+)) and Sr(2+) (analogue of Ca(2+)) tracers simultaneously in a solution through plastic tubes at 10, 50, 150 and 300 cm in depth in a sandy and a clayey Ferralsol soil. A complete randomized design was set up with three replicates of paired trees per injection depth and soil type. Recently expanded leaves were sampled at various times after tracer injection in the summer, and the experiment was repeated in the winter. Soil water contents were continuously monitored at the different depths in the two soils. 3. Determination of foliar Rb and Sr concentrations and (15)N atom % made it possible to estimate the relative uptake potential (RUP) of tracer injections from the four soil depths and the specific RUP (SRUP), defined as RUP, per unit of fine root length density in the corresponding soil layer. 4. The highest tracer uptake rates were found in the topsoil, but contrasting RUP distributions were observed for the three tracers. Whilst the RUP was higher for NO(3)(-)- (15)N than for Rb(+) and Sr(2+) in the upper 50 cm of soil, the highest SRUP values for Sr(2+) and Rb(+) were found at a depth of 300 cm in the sandy soil, as well as in the clayey soil when gravitational solutions reached that depth. 5. Our results suggest that the fine roots of E. grandis trees exhibit contrasting potential uptake rates with depth depending on the nutrient. This functional specialization of roots might contribute to the high growth rates of E. grandis trees, efficiently providing the large amounts of nutrients required throughout the development of these fast-growing plantations.

An assessment of biological and population parameters of the Common whelk, Buccinum undatum (L.) in the region of the North West Irish whelk fishery

The Common whelk, Buccinum undatum (L.) is a conspicuous benthic scavenger in Irish waters, and is a valuable fisheries resource in South East Ireland. B. undatum is fished in many parts of its range, and previous studies have shown that certain life history parameters, which vary with location, make this species vulnerable to overexploitation. This makes research into each exploited stock essential to ensure sustainable fisheries management of the species. In 2003, interest in B. undatum as a complementary species in the inshore fishery east of the Inishowen Peninsula, North West Ireland, initiated investigation into fisheries related biological and population aspects of the species in this region. The current study presents estimates of spatial variation and density of the stock, size at age and growth rates, size and age at onset of sexual maturity, and timing of reproductive events in the region of the North West Irish whelk fishery for the period of June 2003 to May 2004. Analysis of variance of the total shell length of whelk landings to the fishery was conducted over spatial scales of fishing pot, fishing string and landings to vessels. Landings varied significantly in shell length at the spatial scale at which whelks are attracted to baited pots, but did not vary significantly over larger spatial scales. Depletion estimates of stock density from fisheries derived Catch per Unit Effort data and a mark re-capture experiment estimate 0.134 - 0.227 whelks per m2. Two independent methods of age determination found similar growth logistics functions for B. undatum.Modal analysis of length frequency distribution of landings to the fishery estimated symptotic length, Leo = 151.64 mm and Brody growth coefficient, K = 0.04. Analysis of the striae in individual opercula, where each stria was found to represent annual growth, estimated Loo = 137.73 mm and K = 0.12. Common whelks in the region of the North West Irish whelk fishery grow slowly and are long-lived, with 19 opercula striae recorded in one individual. Onset of sexual maturity is late, and no sex-specific differences in size or age at maturity were determined in the present study. Males were found to achieve sexual maturity at 83.30 ± 10.77 mm, and 8.9 - 11.1 years of age, and females at 82.62 ± 10.68 mm and 8.8 to 11.1 years of age. Systematic observations of reproductive events, including histological changes to the female ovary and male testis, and changes in the size and mass of body components, suggest that breeding occurred between the autumn and winter months of October and December 2003. Biological aspects of B. undatum in the study region are compared with previous studies from other regions, and discussed in relation to sustainable management of the fishery.

Synapses on motoneuron dendrites in the brachial section of the frog spinal cord: a computer-aided electron microscopic study of cobalt-filled cells.

Cobalt-labelled motoneuron dendrites of the frog spinal cord at the level of the second spinal nerve were photographed in the electron microscope from long series of ultrathin sections. Three-dimensional computer reconstructions of 120 dendrite segments were analysed. The samples were taken from two locations: proximal to cell body and distal, as defined in a transverse plane of the spinal cord. The dendrites showed highly irregular outlines with many 1-2 microns-long 'thorns' (on average 8.5 thorns per 100 microns 2 of dendritic area). Taken together, the reconstructed dendrite segments from the proximal sites had a total length of about 250 microns; those from the distal locations, 180 microns. On all segments together there were 699 synapses. Nine percent of the synapses were on thorns, and many more close to their base on the dendritic shaft. The synapses were classified in four groups. One third of the synapses were asymmetric with spherical vesicles; one half were symmetric with spherical vesicles; and one tenth were symmetric with flattened vesicles. A fourth, small class of asymmetric synapses had dense-core vesicles. The area of the active zones was large for the asymmetric synapses (median value 0.20 microns 2), and small for the symmetric ones (median value 0.10 microns 2), and the difference was significant. On average, the areas of the active zones of the synapses on thin dendrites were larger than those of synapses on large calibre dendrites. About every 4 microns 2 of dendritic area received one contact. There was a significant difference between the areas of the active zones of the synapses at the two locations. Moreover, the number per unit dendritic length was correlated with dendrite calibre. On average, the active zones covered more than 4% of the dendritic area; this value for thin dendrites was about twice as large as that of large calibre dendrites. We suggest that the larger active zones and the larger synaptic coverage of the thin dendrites compensate for the longer electrotonic distance of these synapses from the soma.

Evaluación poblacional de Gari solida (Gray, 1828) en bahía Independencia-Pisco, junio 2010

En junio 2010, se efectuó la evaluación poblacional de almeja Gari solida en los principales bancos naturales de bahía Independencia: El Ancla, Pan de Azúcar y La Pampa para determinar su distribución, concentración, estructura por tamaños y magnitud poblacional. Los resultados evidenciaron una disminución de la biomasa y población, respecto a agosto del 2008, en 44,9% y 56,2%, respectivamente. La densidad por unidad de muestreo fluctuó entre 1 y 47 ind.m-2, las mayores densidades medias se encontraron en Pan de Azúcar (5,06 ind.m-2), La Pampa (2,42 ind.m-2) y menor densidad en El Ancla (0,57 ind.m-2). La biomasa total se calculó en 336,96 t (± 19,9%) y la población en 8,48 millones de individuos (± 19,85%), el 22,1% de la biomasa correspondió a ejemplares con tamaño mínimo de extracción (TME ≥75 mm). Las tallas de 792 ejemplares analizados fluctuaron entre 4 y 95 mm de longitud valvar, con moda en 65 mm y media en 57,5 mm. El rendimiento promedio del pie con respecto al peso total fue de 1: 9,5.

Effects of recreational fishing on three fish species from the Posidonia oceanica meadows off Minorca (Balearic archipelago, western Mediterranean)

Experimental fishing and visual censuses were conducted at nine Posidonia oceanica sites off Minorca exposed to different levels of fishing intensity to assess the effects of recreational fishing on the species that dominate the catch. Total catch per unit effort (CPUE) was highly seasonal and a statistically significant interaction term existed between the season and the level of fishing intensity. CPUE decreased everywhere at the end of the fishing season (autumn), but such a reduction was more intense at those sites exposed to the highest level of fishing. Visual censuses confirmed that there was a lower abundance of vulnerable fish in autumn. Differences vanished in spring probably because fish reshuffled between the considered sites throughout the winter, when the level of fishing intensity was extremely low. Although the average total lengths of Serranus scriba and Diplodus annularis were unaffected by the level of fishing intensity, the average total length of Coris julis was smaller at the most heavily fished sites. In conclusion, recreational fishing has a relevant impact on most of the exploited species and some of the seasonality reported for the Posidonia oceanica fish assemblages might be caused by the seasonality of the fishery.

Potato crop growth as affected by nitrogen and plant density

Growth and development variables and dry matter characteristics were studied for cultivar Snowden of potato (Solanum tuberosum L.) to evaluate nitrogen and plant density influence. Disregarding ending of season plant stress, the average number of actives haulms per plant was five and it was not affected by plant spacing. However, seasonal and final number of active haulms per plant were increased at 200 kg/ha of nitrogen. Maximum stem elongation was reached quickly with double density and had the tendency to keep constant at the highest and lowest nitrogen levels after 70 days after planting. Specific stem mass defined as mass per unit stem length was established as an indirect measure of stem thickness and load capacity. Specific leaf mass position in plant was higher at upper stem leaves, increased as plant density increased and did not vary markedly over time throughout the season. The rate of leaf appearance increased drastically due to more branching caused by high nitrogen level, and increased above ground dry matter per plant. Canopy growth and development influenced main tuber yield components. The number of active tubers per haulm decreased after 60 days after planting showing that tuberization is reversible. Tuber growth functions were established allowing the estimate of dry biomass partitioning coefficients for each plant organ.

Understanding the mechanisms of lung mechanical stress

Physical forces affect both the function and phenotype of cells in the lung. Bronchial, alveolar, and other parenchymal cells, as well as fibroblasts and macrophages, are normally subjected to a variety of passive and active mechanical forces associated with lung inflation and vascular perfusion as a result of the dynamic nature of lung function. These forces include changes in stress (force per unit area) or strain (any forced change in length in relation to the initial length) and shear stress (the stress component parallel to a given surface). The responses of cells to mechanical forces are the result of the cell's ability to sense and transduce these stimuli into intracellular signaling pathways able to communicate the information to its interior. This review will focus on the modulation of intracellular pathways by lung mechanical forces and the intercellular signaling. A better understanding of the mechanisms by which lung cells transduce physical forces into biochemical and biological signals is of key importance for identifying targets for the treatment and prevention of physical force-related disorders.

Utilisation of Coir Geotextiles for Unpaved Roads and Embankments

The increasing tempo of construction activity the world over creates heavy pressure on existing land space. The quest for new and competent site often points to the needs for improving existing sites, which are otherwise deemed unsuitable for adopting conventional foundations. This is accomplished by ground improvement methods, which are employed to improve the quality of soil incompetent in their natural state. Among the construction activities, a well-connected road network is one of the basic infrastructure requirements, which play a vital role for the fast and comfortable movement of inter- regional traffic in countries like India.One of the innovative ground improvement techniques practised all over the world is the use of geosynthetics, which include geotextiles, geomembranes, geogrids, etc . They offer the advantages such as space saving, enviromnental sensitivity, material availability, technical superiority, higher cost savings, less construction time, etc . Because of its fundamental properties, such as tensile strength, filtering and water permeability, a geotextile inserted between the base material and sub grade can function as reinforcement, a filter medium, a separation layer and as a drainage medium. Though polymeric geotextiles are used in abundant quantities, the use of natural geotextiles (like coir, jute, etc.) has yet to get momentum. This is primarily due to the lack of research work on natural geotextilcs for ground improvement, particularly in the areas of un paved roads. Coir geotextiles are best suited for low cost applications because of its availability at low prices compared to its synthetic counterparts. The proper utilisation of coir geotextilcs in various applications demands large quantities of the product, which in turn can create a boom in the coir industry. The present study aims at exploring the possibilities of utilising coir geotextiles for unpaved roads and embankments.The properties of coir geotextiles used have been evaluated. The properties studied include mass per unit area, puncture resistance, tensile strength, secant modulus, etc . The interfacial friction between soils and three types of coir geotextiles used was also evaluated. It was found that though the parameters evaluated for coir geotextiles have low values compared to polymeric geotextiles, the former are sufficient for use in unpaved roads and embankments. The frictional characteristics of coir geotextile - soil interfaces are extremely good and satisfy the condition set by the International Geosynthetic Society for varied applications.The performance of coir geotextiles reinforced subgrade was studied by conducting California Bearing Ratio (CBR) tests. Studies were made with coir geotextiles placed at different levels and also in multiple layers. The results have shown that the coir geotextile enhances the subgrade strength. A regression analysis was perfonned and a mathematical model was developed to predict the CBR of the coir geotextile reinforced subgrade soil as a function of the soil properties, coir geotextile properties, and placement depth of reinforcement.The effects of coir geotextiles on bearing capacity were studied by perfonning plate load tests in a test tan1e This helped to understand the functioning of geotextile as reinforcement in unpaved roads and embankments. The perfonnance of different types of coir geotextiles with respect to the placement depth in dry and saturated conditions was studied. The results revealed that the bearing capacity of coir-reinforced soil is increasing irrespective of the type of coir geotextiles and saturation condition.The rut behaviour of unreinforced and coir reinforced unpaved road sections were compared by conducting model static load tests in a test tank and also under repetitive loads in a wheel track test facility. The results showed that coir geotextiles could fulfill the functions as reinforcement and as a separator, both under static and repetitive loads. The rut depth was very much reduced whik placing coir geotextiles in between sub grade and sub base.In order to study the use of Coir geotextiles in improving the settlement characteristics, two types of prefabricated COlf geotextile vertical drains were developed and their time - settlement behaviour were studied. Three different dispositions were tried. It was found that the coir geotextile drains were very effective in reducing consolidation time due to radial drainage. The circular drains in triangular disposition gave maximum beneficial effect.In long run, the degradation of coir geotextile is expected, which results in a soil - fibre matrix. Hence, studies pertaining to strength and compressibility characteristics of soil - coir fibre composites were conducted. Experiments were done using coir fibres having different aspect ratios and in different proportions. The results revealed that the strength of the soil was increased by 150% to 200% when mixed with 2% of fibre having approximately 12mm length, at all compaction conditions. Also, the coefficient of consolidation increased and compression index decreased with the addition of coir fibre.Typical design charts were prepared for the design of coir geotextile reinforced unpaved roads. Some illustrative examples are also given. The results demonstrated that a considerable saving in subase / base thickness can he achieved with the use of eoir geotextiles, which in turn, would save large quantities of natural aggregates.