High Carbon Ferro-chromium Production by Self-reducing Process: Effects of Fe-Si and Fluxing Agent Additions

The technology of self-reducing pellets for ferro-alloys production is becoming an emerging process due to the lower electric energy consumption and the improvement of metal recovery in comparison with the traditional process. This paper presents the effects of reduction temperature, addition of ferro-silicon and addition of slag forming agents for the production of high carbon ferro-chromium by utilization of self-reducing pellets. These pellets were composed of Brazilian chromium ore (chromite) concentrate, petroleum coke, Portland cement, ferro-silicon and slag forming components (silica and hydrated lime). The pellets were processed at 1 773 K, 1 823 K and 1 873 K using an induction furnace. The products obtained, containing slag and metallic phases, were analyzed by scanning electron microscopy and chemical analyses (XEDS). A large effect on the reduction time was observed by increasing the temperature from 1 773 K to 1 823 K for pellets without Fe-Si addition: around 4 times faster at 1 823 K than at 1 773 K for reaction fraction close to one. However, when the temperature was further increased from 1 823 K to 1 873 K the kinetics improved by double. At 1 773 K, the addition of 2% of ferro-silicon in the pellet resulted in an increasing reaction rate of around 6 times, in comparison with agglomerate without it. The addition of fluxing agents (silica and lime), which form initial slag before the reduction is completed, impaired the full reduction. These pellets became less porous after the reduction process.

High Carbon Ferro-Chromium by Self-Reducing Process

This paper discusses the effects of temperature, addition of ferro-silicon and fluxing agents for the production of high carbon ferro-chromium by self-reducing process. The use of self-reducing agglomerates for ferro-alloys production is becoming an emerging processing technology due to lowering the electric energy consumption and improving the metal recovery in comparison with traditional ones. The self-reducing pellets were composed by chromite, petroleum coke, cement and small (0.1% - 2%) addition of ferro-silicon. The slag composition was adjusted by addition of fluxing agents. The reduction of pellets was carried out at 1773K (1500 degrees C), 1823K (1550 degrees C) and 1873K (1600 degrees C) by using induction furnace. The products obtained, containing slag and metallic phases, were analyzed by scanning electron microscopy and chemical analyses (XEDS). By increasing temperature from 1773K to 1823K large effect on the reduction time was observed. It decreased from 30 minutes to 10 minutes, for reaching around 0.98 reduction fraction. No significant effect on reduction time was observed when the reduction temperature was increased from 1823K to 1873K. At 1773K, the addition of 2% of ferro-silicon in the pellet resulted in an increasing reaction rate of around 6 times, in comparison with agglomerate without this addition. The addition of fluxing agents (silica and hydrated lime) has effect on reduction time (inverse relationship) and the pellets become less porous after reduction.

The roles played by Aspergillus nidulans apoptosis-inducing factor (AIF)-like mitochondrial oxidoreductase (AifA) and NADH-ubiquinone oxidoreductases (NdeA-B and NdiA) in farnesol resistance

Farnesol (FOH) is a nonsterol isoprenold produced by dephosphorylanon of farnesyl pyrophosphate a catabolite of the cholesterol biosynthetic pathway These isoprenoids inhibit proliferation and induce apoptosis Here we show that Aspergillus nidulans MA encoding the apoptosis-Inducing factor (AIF)-like mitochondrial oxidoreductase plays a role in the function of the mitochondrial Complex I Additionally we demonstrated that ndeA B and ndiA encode external and internal alternative NADH dehydrogenases respectively that have a function in FOH resistance When exposed to FOH the Delta aifA and Delta ndeA strains have increased ROS production while Delta ndeB Delta ndeA Delta ndeB and Andul mutant strains showed the same ROS accumulation than in the absence of FOH We observed several compensatory mechanisms affecting the differential survival of these mutants to FOH (C) 2010 Elsevier Inc All rights reserved

Instantaneous outbursts in underground coal mines: An overview and association with coal type

Instantaneous outbursts in underground coal mines have occurred in at least 16 countries, involving both methane (CH4) and carbon dioxide (CO2). The precise mechanisms of an instantaneous outburst are still unresolved but must consider the effects of stress, gas content and physico-mechanical properties of the coal. Other factors such as mining methods (e.g., development heading into the coal seam) and geological features (e.g., coal seam disruptions from faulting) can combine to exacerbate the problem. Prediction techniques continue to be unreliable and unexpected outburst incidents resulting in fatalities are a major concern for underground coal operations. Gas content thresholds of 9 m(3)/t for CH4 and 6 m(3)/t for CO2 are used in the Sydney Basin, to indicate outburst-prone conditions, but are reviewed on an individual mine basis and in mixed as situations. Data on the sorption behaviour of Bowen Basin coals from Australia have provided an explanation for the conflicting results obtained by coal face desorption indices used for outburst-proneness assessment. A key factor appears to be different desorption rates displayed by banded coals, which is supported by both laboratory and mine-site investigations. Dull coal bands with high fusinite and semifusinite contents tend to display rapid desorption from solid coal, for a given pressure drop. The opposite is true for bright coal bands with high vitrinite contents and dull coal bands with high inertodetrinite contents. Consequently, when face samples of dull, fusinite-or semifusinite-rich coal of small particle size are taken for desorption testing, much gas has already escaped and low readings result. The converse applies for samples taken from coal bands with high vitrinite and/or inertodetrinite contents. In terms of outburst potential, it is the bright, vitrinite-rich and the dull, inertodetrinite-rich sections of a coal seam that appear to be more outburst-prone. This is due to the ability of the solid coal to retain gas, even after pressure reduction, creating a gas content gradient across the coal face sufficient to initiate an outburst. Once the particle size of the coal is reduced, rapid gas desorption can then take place. (C) 1998 Elsevier Science.

Controlled partial mine ventiliation recirculation trial at Mount Isa Mines

The ventilation and cooling of deep, hot mines present particular problems in Australia as a consequence of the surface climate, the size of the underground voids, the degree of mechanization and the cost of power in remote areas. A preliminary investigation of the effects of controlled partial recirculation of air was conducted in Mount Isa Mines' Deep Copper section. Gas and dust concentrations were measured in the exhaust air of the major working section to assess the potential for recirculating exhaust air to the intake airways to reduce the cost of providing an acceptable working environment in the deep parts of the mine. Studies were undertaken of airborne dust deposition in vertical airways and the efficiency of usage of the ventilation air in diluting contaminants. It was established that 45% of the respirable dust was deposited in a 130-m vertical raise and 60% of the air supplied to the section could be reused or recirculated. The first major field trial of a controlled partial recirculation system in Australia was undertaken in the light of these results and demonstrated excellent potential for significant reduction in ventilation costs. Gas and dust contaminant levels were well below the threshold limit values during the trial. It is concluded that controlled partial recirculation can be a practical, effective and safe aid to normal ventilation practice in Australian deep, hot mines.

Quantifying stresses and support requirements in the undercut and production level drifts of block and panel caving mines

A numerical modelling strategy has been developed in order to quantify the magnitude of induced stresses at the boundaries of production level and undercut level drifts for various in situ stress environments and undercut scenarios. The results of the stress modelling were in line with qualitative experiential guidelines and a limited number of induced stress measurements documented from caving sites. A number of stress charts were developed which quantify the maximum boundary stresses in drift roofs for varying in situ stress regimes, depths and undercut scenarios. This enabled many of the experiential guidelines to be quantified and bounded. A limited number of case histories of support and support performance in cave mine drifts were compared to support recommendations using the NGI classification system, The stress charts were used to estimate the Stress Reduction Factor for this system. The back-analyses suggested that the NGI classification system might be able to give preliminary estimates of support requirements in caving mines with modifications relating to rock bolt length and the support of production level intersections. (C) 2002 Elsevier Science Ltd. All rights reserved.

Coal dust exposures in the longwall mines of New South Wales, Australia: a respiratory risk assessment

This paper presents an analysis of personal respirable coal dust measurements recorded by the Joint Coal Board in the underground longwall mines of New South Wales from 1985 to 1999. A description of the longwall mining process is given. In the study, 11 829 measurements from 33 mines were analysed and the results given for each occupation, for seven occupational groups, for individual de-identified mines and for each year of study. The mean respirable coal dust concentration for all jobs was 1.51 mg/m(3) (SD 1.08 mg/m(3)). Only 6.9% of the measurements exceeded the Australian exposure standard of 3 mg/m(3). Published exposure-response relationships were used to predict the prevalence of progressive massive fibrosis and the mean loss of FEV1, after a working lifetime (40 years) of exposure to the mean observed concentration of 1.5 mg/m(3). Prevalences of 1.3 and 2.9% were predicted, based on data from the UK and the USA, respectively. The mean loss of FEV1 was estimated to be 73.7 ml.

A reforma administrativa da Nova Zel??ndia nos anos 80-90: controle estrat??gico, efici??ncia gerencial e accountability

O artigo discute o processo de reforma administrativa implementada na Nova Zel??ndia a partir de 1984, com a chegada do Partido Trabalhista ao poder, abordando seus principais desdobramentos nos anos 90. Parte de uma apresenta????o do modelo administrativo em vigor na Nova Zel??ndia antes das reformas empreendidas em 1984, delimitando dessa forma o quadro referencial para comparar a situa????o anterior com a atual, de maneira que proporcione uma avalia????o sobre os impactos das medidas empreendidas. Em seguida, apresenta uma descri????o dos objetivos e princ??pios norteadores da reforma tais como, separa????o das fun????es comerciais das n??o-comerciais; separa????o entre as fun????es administrativas e de assessoria; princ??pio do ???quem usa paga???, user pays; transpar??ncia na concess??o de subs??dios; neutralidade competitiva, descentraliza????o e aumento do poder discricion??rio do administrador; melhoramento da accountability, entre outros. A seguir, s??o apresentadas as principais medidas empreendidas pelo governo trabalhista entre 1984 e 1990, dando ??nfase ?? metodologia adotada para a implementa????o e accountability dos contratos de gest??o firmados entre os executivos- chefe e os ministros. Posteriormente, o autor apresenta as modifica????es introduzidas nas regras de contrata????o de pessoal no servi??o p??blico neozeland??s e, de um modo mais geral, na pol??tica de recursos humanos. Finalmente, ?? tra??ado um perfil da situa????o atual da Nova Zel??ndia, bem como ?? feita a apresenta????o sucinta daqueles que o autor considera como sendo os ???suportes conceituais da reforma???: o movimento gerencialista, a teoria do Public Choice e a teoria Principal-Agente.

Quadros de Ferro? Influências da historiografia na produção de livros didáticos de história regional nos municípios capixabas de Anchieta e Piúma

Espremidas entre o mar e as montanhas, as cidades de Piúma e Anchieta, no litoral sul capixaba, tiveram sua rotina de redes e anzóis alterada com a chegada da Samarco no final da década de 1970 e, posteriormente, do turismo e da exploração do petróleo e do gás. Incomodados, alguns munícipes promoveram atividades que, acreditavam, construiriam uma representação de identidade regional. Entre essas iniciativas está a publicação de livros didáticos abordando a história e a geografia daqueles municípios. Para compreendermos o processo de produção e a narrativa contida nesses livros, nos apoiamos nos conceitos de representação, apropriação e autoria de Chartier (1990, 2002, 2010, 2012) e na análise das relações entre os três sentidos da história – o cotidiano, o escolar e o acadêmico - e do dilema que acompanha a história escolar desde sua origem e que transformou os livros didáticos em documentos de identidade, pensadas por Carretero (2010). O que se encontrou foi uma representação de identidade local que suporta distintas temporalidades, entre elas se destaca o que se chama de influência Varnhagen que produziu uma identidade como resultado da participação das etnias negra e indígena, mas sob predomínio europeu.

Processo auto - sustentável de sinterização de pelotas de minério de ferro: influência da estrutura

O Brasil é um dos países que possuem as maiores jazidas de minério de ferro do mundo. Devido aos recursos financeiros envolvidos, mão-de-obra, arrecadação de impostos, envolvimento de atividades logísticas e comercialização exterior, a mineração é uma das principais atividades econômicas do país, envolvendo nesse contexto as plantas de pelotização de minério de ferro. As pelotas de minério de ferro são um dos insumos essenciais utilizados na produção mundial do aço. Compostas essencialmente de óxido de ferro (Fe2O3), são aglomerados com diâmetro que varia de 6,3 a 16 mm, cuja sua produção envolve a combustão para que obtenham a resistência mecânica necessária para serem utilizadas nos alto fornos siderúrgicos. Tal característica impede que as pelotas se quebrem e se transformem em finos, dificultando a permeação do ar através da carga do alto forno e consequentemente reduzindo a eficiência da queima e produção do ferro gusa, o qual é transformado em aço nas etapas posteriores de refino. Para garantir a produção de pelotas com a qualidade desejada, especialmente nos aspectos de composição e resistência mecânica, foi proposta queima controlada em reator de leito fixo simulando as características dos fornos utilizados na indústria. Com os resultados obtidos, foi possível correlacionar nível de temperatura, consumo de O2 e geração de CO2 e resistência à compressão, permitindo o aprimoramento do processo de combustão de pelotas, além de atestar a possibilidade de utilização de outros combustíveis sólidos como alternativas ao gás natural.

Desafios e dilemas dos grandes países periféricos: Brasil e Índia

O artigo parte de uma análise das estratégias de perpetuação das estruturas hegemônicas de Poder e dos objetivos mais gerais dos grandes países periféricos (no caso, Brasil e Índia) para, então, propor estratégias para a melhor inserção destes naquelas.

China e Índia: emergência e impacto cultural

China e Índia fazem parte do noticiário cotidiano. Dois momentos históricos recentes marcaram aqueles países. O primeiro foi a abertura chinesa para o exterior, na década de 1980. O segundo é a emergência indiana atual. A maioria das análises disponíveis, no entanto, se esgota na expansão das duas economias. O artigo, contudo, busca situar o impacto que a multiculturalidade daquelas civilizações poderá causar em novo ordenamento internacional, distinto do atual, onde prevalece a força militar e o poder econômico. São apresentadas, em linhas gerais, as origens e a espiritualidade dos povos em questão.