On line pre-concentration for simultaneous determination of low molecular weight organic acids and inorganic anions in Amazonian river water samples employing ion chromatography with conductivity detection

An ion chromatography procedure, employing an IonPac AC15 concentrator column was used to investigate on line preconcentration for the simultaneous determination of inorganic anions and organic acids in river water. Twelve organic acids and nine inorganic anions were separated without any interference from other compounds and carry-over problems between samples. The injection loop was replaced by a Dionex AC15 concentrator column. The proposed procedure employed an auto-sampler that injected 1.5 ml of sample into a KOH mobile phase, generated by an Eluent Generator, at 1.5 mL min-1, which carried the sample to the chromatographic columns (one guard column, model AG-15, and one analytical column, model AS15, with 250 x 4mm i.d.). The gradient elution concentrations consisted of a 10.0 mmol l-1 KOH solution from 0 to 6.5 min, gradually increased to 45.0 mmol l-1 KOH at 21 min., and immediatelly returned and maintained at the initial concentrations until 24 min. of total run. The compounds were eluted and transported to an electro-conductivity detection cell that was attached to an electrochemical detector. The advantage of using concentrator column was the capability of performing routine simultaneous determinations for ions from 0.01 to 1.0 mg l-1 organic acids (acetate, propionic acid, formic acid, butyric acid, glycolic acid, pyruvate, tartaric acid, phthalic acid, methanesulfonic acid, valeric acid, maleic acid, oxalic acid, chlorate and citric acid) and 0.01 to 5.0 mg l-1 inorganic anions (fluoride, chloride, nitrite, nitrate, bromide, sulfate and phosphate), without extensive sample pretreatment and with an analysis time of only 24 minutes.

Assessment of the VoIP Transmission Quality over Digital Power Line Carrier Channels

This article is devoted to the research of VoIP transmission quality over Digital Power Line Carrier channels. Assessment of quality transmission is performed using E-model. Paper considers the possibility of joint using of Digital Power Line carrier equipment with different architecture in one network. As a result of the research, the rule for constructing of multi-segment Digital Power Line Carrier channels was formulated. This rule allows minimizing the transmission delay and saving frequency resources of high voltage Power Line Carrier range.

On-line desorption of dried blood spot: A novel approach for the direct LC/MS analysis of micro-whole blood samples.

The aim of this work is to present a new concept, called on-line desorption of dried blood spots (on-line DBS), allowing the direct analysis of a dried blood spot coupled to liquid chromatography mass spectrometry device (LC/MS). The system is based on an inox cell which can receive a blood sample (10 microL) previously spotted on a filter paper. The cell is then integrated into LC/MS system where the analytes are desorbed out of the paper towards a column switching system ensuring the purification and separation of the compounds before their detection on a single quadrupole MS coupled to atmospheric pressure chemical ionisation (APCI) source. The described procedure implies that no pretreatment is necessary in spite the analysis is based on whole blood sample. To ensure the applicability of the concept, saquinavir, imipramine, and verapamil were chosen. Despite the use of a small sampling volume and a single quadrupole detector, on-line DBS allowed the analyses of these three compounds over their therapeutic concentrations from 50 to 500 ng/mL for imipramine and verapamil and from 100 to 1000 ng/mL for saquinavir. Moreover, the method showed good repeatability with relative standard deviation (RSD) lower than 15% based on two levels of concentration (low and high). Function responses were found to be linear over the therapeutic concentration for each compound and were used to determine the concentrations of real patient samples for saquinavir. Comparison of the founded values with those of a validated method used routinely in a reference laboratory showed a good correlation between the two methods. Moreover, good selectivity was observed ensuring that no endogenous or chemical components interfered with the quantitation of the analytes. This work demonstrates the feasibility and applicability of the on-line DBS procedure for bioanalysis.

Uuteaineiden on-line-mittaus koivusulfaattisellutehtaalla

Tämän työn tarkoituksena oli tutkia pihkanhallintaa sulfaattisellutehtaalla ja uuteaineiden analysointimenetelmiä massasta ja suodoksesta. Tavoitteena oli kehittää uuteaineiden on-line mittausmenetelmä sulfaattisellutehtaalle. Kirjallisuusosassa esitettiin sulfaattisellun valmistusprosessi ja uuteaineiden käyttäytyminen prosessissa. Lisäksi työssä käsiteltiin tärkeimpiä pihkanhallintamenetelmiä ja uuteaineiden analysointia. Kokeellisessa osassa määritettiin uuteainepitoisuudet 29:stä massa- ja pesusuodosnäytteestä. Lisäksi suodosnäytteiden sameus ja kemiallinen hapenkulutus määritettiin laboratoriossa. On-line mittaukset tehtiin DD-pesurin paluusuodoksesta, josta mitattiin johtokyky, lämpötila, taitekerroin ja pH. Sameutta yritettiin mitata on-line nefelometrillä, mutta käytössä ollut laite ei soveltunut tumman suodoksen mittaamiseen. Työssä saatujen tulosten perusteella voidaan todeta, että pesusuodoksen ominaisuuksia mittaamalla ei voida arvioida massan uutepitoisuutta luotettavasti. Suodoksen ja massan uutepitoisuuksien välinen selitysaste oli 54%. Saippuoitumattomien uuteaineiden pitoisuuden ollessa erityisen suuri, suodoksen uutepitoisuus ei korreloi massassa olevan uutteen määrän kanssa. Täten kyseinen mittausmenetelmä ei ole sopiva, sillä se ei toimi silloin, kun olisi tärkeintä tietää oikea uuteainepitoisuus pihkanhallintakemikaalien annosten määrittämiseksi. Suodoksen sameus riippui sen uutepitoisuudesta 80% selitysasteella. Sameusmittaus on nopea ja suhteellisen luotettava menetelmä suodosten uutepitoisuuksien arviointiin, mutta se vaatii mittalaitteen joka käyttää usean ilmaisimen tekniikkaa. On-line-mittauksissa laitteisto tulisi varustaa automaattisella pesulaitteella, sillä mittarin linssit likaantuvat helposti prosessivirrassa.

Événements et déformations tardi-métamorphiques dans le segment Ossola-Ticino (Val Vigezzo-Centovalli, Italie-Suisse)

RESUME: Une zone tectonique large et complexe, connue sous le nom de ligne des Centovalli, traverse le secteur des Alpes Centrales compris entre Domodossola et Locarno. Cette région, formée par le Val Vigezzo et la vallée des Centovalli, constitue la terminaison méridionale du dôme Lepontin et représente une portion de la zone des racines des nappes alpines. Elle fait partie d’une grande et complexe zone de cisaillement, en partie associée à des phénomènes hydrothermaux d’âge alpin (<20 Ma), qui comprend le système tectonique Insubrien et celui du Simplon. Le Val Vigezzo et les Centovalli constituent un vrai carrefour entre les principaux accidents tectoniques des Alpes ainsi qu'une zone de juxtaposition du socle Sudalpin avec la zone des racines de l’Austroalpin et du Pennique. Les phases de déformation et les structures géologiques qui peuvent être étudiées s'étalent sur une période comprise entre environ 35 Ma et l'actuel. L’étude détaillée de terrain a mis en évidence la présence de nombreuses roches et structures de déformation de type ductile et cassant tels que des mylonites, des cataclasites, des pseudotachylites, des kakirites, des failles minéralisées, des gouges de faille et des plis. Sur le terrain on a pu distinguer au moins quatre générations de plis liés aux différentes phases de déformation. Le nombre et la complexité de ces structures indiquent une histoire très compliquée, selon plusieurs étapes distinctes, parfois liées, voire même superposées. Une partie de ces structures de déformation affectent aussi les dépôts sédimentaires d’âge quaternaire, notamment des limons et des sables lacustres. Ces sédiments constituent les restes d'un bassin lacustre attribué à l'époque interglaciaire Riss/Würm (éemien, 67.000-120.000 ans) et ils affleurent dans la partie centrale de la zone étudiée, à l'Est de la plaine de Santa Maria Maggiore. Ces sédiments montrent en leur sein toute une série de structures de déformation tels que des plans de faille inverses, des structures conjuguées de raccourcissement et des véritables plis. Ces failles et ces plis représenteraient les évidences de surface d’une déformation probablement active en époque quaternaire. Une autre formation rocheuse a retenu tout notre attention; il s'agit d'un corps de brèches péridotitiques monogéniques qui affleure en discontinuité le long du versant méridional et le long du fond de la vallée Vigezzo sur environ 20 km. Ces brèches se posent indifféremment sur le socle (unités Finero, Orselina) ou sur les sédiments lacustres. Elles sont traversées par des plans de failles qui développent des véritables stries de faille et des gouges de faille; l’orientation de ces plans est la même que celle affectant les failles à gouges du socle. La genèse de cette brèche est liée à l'altération et au modelage glacier (rock-glaciers) d'une brèche tectonique originelle qui borde la partie externe du Corps de Finero. Les structures de déformation de cette brèche, pareillement à celles des sédiments lacustres, ont été considérées comme les évidences de surface d'une tectonique quaternaire active dans la région. La dernière phase de déformation cassante qui affecte cette région peut donc être considérée comme active en époque quaternaire. Une vue d’ensemble de la région étudiée nous permet de reconnaître à l’échelle régionale une zone de cisaillement complexe orientée E-W, parallèlement à l’axe de la vallée Centovalli-Val Vigezzo. Les données de terrain, indiquent que cette zone de cisaillement débute sous conditions ductiles et évolue en plusieurs étapes jusqu’à des conditions de failles cassantes de surface. La reconstruction de l'évolution géodynamique de la région a permis de définir trois étapes distinctes qui marquent le passage, de ce secteur de socle cristallin, de conditions P-T profondes à des conditions de surface. Dans ce contexte, on a reconnu trois phases principales de déformation à l’échelle régionale qui caractérisent ces trois étapes. La phase la plus ancienne est constituée par des mylonites en faciès amphibolite, associées à des mouvements de cisaillement dextre, qui sont ensuite remplacés par des mylonites en faciès schistes verts et des plis rétrovergentes liés au rétrocharriage des nappes alpines. Une deuxième étape est identifiée par le développement d’une phase hydrothermale liée à un système de failles extensives et décrochantes dextres à direction principale E-W, NE-SW et NW-SE. Leur caractérisation minéralogique a permis la mise en évidence des phases cristallines de néoformation liées à cet événement constituées par : K-feldspath (microcline), chlorites (Fe+Mg), épidotes, prehnite, zéolites (laumontite), sphène, calcite. Dans ce contexte, pour obtenir une meilleure caractérisation de cet événement hydrothermal on a utilisé des géothermomètres sur chlorites, sensible aussi à la pression et a la a(H2O), qui ont donné des valeurs descendantes comprises entre 450-200°C. Les derniers mouvements sont mis en évidence par le développement d’une série de plans majeurs de failles à gouge, qui forment une structure en sigmoïdes d’épaisseur kilométrique reconnaissable à l’échelle de la vallée et caractérisée par des mouvements transpressifs avec une composante décrochante dextre toujours importante. Cette phase de déformation forme un système conjugué de failles avec direction moyenne E-W qui coupent la zone des racines des nappes alpines, la zone du Canavese et le corps ultramafique de Finero. Ce système se déroule de manière subparallèle à l'axe de la vallée le long de plusieurs dizaines de kilomètres. Une analyse complète et détaillée des gouges de faille par XRD a montré que la fraction argileuse (<2 µm) de ces gouges contient une partie de néoformation très importante constituée par, des illites, des chlorites et des interstratifiés de type illite/smectite ou chlorite/smectite. Des datations avec méthode K-Ar sur ces illites ont donné des valeurs comprises entre 12 et 4 Ma qui représentent l'âge de cette dernière déformation cassante. L'application de la méthode de la cristallinité de l'illite (C.I.) a permis d'évaluer les conditions thermiques qui caractérisent le déroulement de cette dernière phase tectonique qui se produit sous conditions de température caractéristiques de l'anchizone et de la diagenèse. L'ensemble des structures de déformation qu'on vient de décrire s'insère parfaitement dans le contexte de convergence oblique entre la plaque adriatique et celle européenne qui à produit l'orogène alpin. On peut considérer les structures tectoniques du Val Vigezzo-Centovalli comme l'expression d'une zone majeure de cisaillement "Simplo-Insubrienne". L'empilement structural et les structures tectoniques affleurantes dans la région sont le résultat de l'interaction entre un régime tectonique transpressif et un régime transtensif. Ces deux champs de tension sont antagonistes entre eux mais sont reliés, de toute façon, à une seule phase décrochante dextre principale, due à une convergence oblique entre deux plaques. À l'échelle de l'évolution géodynamique on peut distinguer différentes étapes au cours desquelles les structures de ces deux régimes tectoniques interagissent en manière différente. En accord avec les données géophysiques et les reconstructions paléodynamiques prises dans la littérature on considère que la ligne Rhône-Simplon-Centovalli représente l'évidence de surface de la suture majeure profonde entre la plaque Adriatique et celle Européenne. Les vitesses de soulèvement qui ont été calculées dans cette étude pour cette région des Alpes donnent une valeur moyenne de 0.8 mm/a qui est tout à fait comparable avec les données proposées par la littérature sur cette zone. La zone Val Vigezzo-Centovalli peut être donc considérée comme un carrefour géologique où se croisent différentes phases tectoniques qui représentent les évidences de surface d'une suture profonde majeure entre deux plaques dans un contexte de collision continentale. ABSTRACT: A wide and complex tectonic zone known as Centovalli line, crosses the Central Alps sector between Domodossola and Locarno. This area, formed by the Vigezzo Valley and Centovalli valley, constitutes the southernmost termination of the Lepontin dome and represents a portion of the alpine nappes root zone. It belongs to a large and complex shear-zone, partly associated with hydrothermal phenomena of alpine age (<20 My), which includes the Insubric Line and the Simplon fault zone. Vigezzo Valley and Centovalli constitute a real crossroads between the mains alpines tectonics lines as well as a zone of juxtaposition of the Southalpine basement with the Austroalpin and Pennique root zone. The deformation phases and the geological structures that can be studied between approximately 35 My and the present. The detailed field study showed the presence of many brittle and ductile deformation structures and fault rocks such as mylonites, cataclasites, pseudotachylites, kakirites, mineralized faults, fault gouges and folds. In the field we could distinguish at least four folds generations related to the various deformation phases. The number and the complexity of these structures indicate a very complicated history, comprising several different stages, that sometimes are related and even superimposed. Part of these deformation structures affect also the sedimentary deposits of quaternary age, in particular the silts and sands lake deposit. These sediments constitute the remainders of a lake basin ascribed to the interglacial Riss/Würm (Eemien, 67.000-120.000 years) and outcroping in the central part of the studied area, in the Eastern part of Santa Maria Maggiore plain. These sediments show a whole series of deformation structures such as inverse fault planes, combined shortening structures and true folds. These faults and folds would represent the surface evidence of a probably active tectonic deformation in quaternary time. Another rock formation attracted all our attention. It is a body of monogenic peridotite breccia which outcrops in discontinuity along the southernmost slope and the bottom of the Vigezzo valley on approximately 20 km. This breccia lies indifferently on the basement (Finero and Orselina units) or on the lake sediments. They are crossed by fault planes which developed slikenside and fault gouges whose orientation is the same of the faults gouges in the alpine basement. This breccia results from the weathering and the surface modelling of an original tectonic breccia which borders the external part of Finero peridotite body. This breccia deformation structures, like those of the lake sediments, were regarded as the surface interaction of active quaternary tectonics in the area. So the last brittle deformation phases which affects this area seems to be actives in quaternary time. Theoverall picture of the studied area on a regional scale enables us to point out a complex shear-zone directed E-W, parallel to the axis of the Centovalli and Vigezzo Valley. The field analysis indicates that this shear-zone began under ductile conditions and evolved in several stages to brittle faulting under surface conditions. The analysis of the geodynamic evolution of the area allows to define three different stages which mark the transition of this alpine basement root zone, from deep P-T conditions to P-T surface conditions. In this context on regional scale three principal deformation phases, which characterize these three stages can be distinguished. The oldest phase consisted of the amphibolitie facies mylonites, associated to dextral strikeslip movements. They are then replaced by green-schists facies mylonites and backfolds related to the backthrusting of the alpines nappes. A second episode is caracterized by the development of an hydrothermal phase bound to an extensive fault and dextral strike-slip fault system, with E-W, NW-SE and SE-NW principal directionsThe principal neoformed mineral phases related to this event are: K-feldspar (microcline), chlorites (Fe+Mg), epidotes prehnite, zéolites (laumontite), sphene and calcite. In this context, to obtain a better characterization of this hydrothermal event, we have used an chlorite geothermometer, sensitive also to the pressure and has the a(H2O), which gave downward values ranging between 450-200°C. The last movements are caracterized by the development of important gouge fault plans, which form a sigmoid structure of kilometric thickness which is recognizable at the valley scale, and is characterized by transpressive movements always with a significant dextral strike-slip component. This deformation phase forms a combined faults system with an average E-W direction, which cuts trough the alpine root zone, the Canavese zone and the Finero ultramafic body. This fault system takes place subparallel to the axis of the valley over several tens of kilometers. A complete and detailed XRD analysis of the gouges fault showed that the clay fraction (<2µm) contains a very significant neo-formation of illite, chlorites and mixed layered clays such as illite/smectite or chlorite/smectite. The K-Ar datings of the illite fraction <2µm gave values ranging between 12 and 4 My and the illite fraction <0.2µm gave more recents values until to 2,4-0 My.This values represent the age of this last brittle deformation. The application of the illite crystallinity method (C.I.) allowed evaluating the thermal conditions which characterize this tectonic phase that occured under temperature conditions of the anchizone and diagenesis. The whole set of deformation structures which we just described, perfectly fit the context of oblique convergence between the Adriatic and the European plate that produced the alpine orogen. We can regard the Vigezzo valley and Centovalli tectonic structures as the expression of a major "Simplo-Insubric" shear-zone. Structural stacking and tectonic structures that outcrop in the studied area, are the result of the interaction between a transpressive and a transtensve tectonic phases. These two tension fields are antagonistic but they are also connected, in any event, with only one principal dextral strike-slip movement, caused by an oblique convergence between two plates. On the geodynamic evolution scale we can distinguish various stages during which these two tectonic structures fields interact in various ways. In agreement with the geophysical data and the paleodynamic recostructions taken in the literature we considers that the Rhone-Simplon-Centovalli line are the surface feature of the major collision between the Adriatique and the European plate at depth. The uplift speeds we calculated in this study for this Alpine area give an average value of 0.8 mm/a, which is in good agreement with the data suggested by the literature on this zone. TheVigezzo Valley and Centovalli zone can therefore be regarded as a geological crossroad where various tectonic phases are superimposed. They represent the evidences of a major and deeper suture between two plates in a continental collision context.

On-line –jatkojalostuksen integrointi mäntysahan tuotantoprosessiin

Diplomityön tavoitteena oli selvittää erilaisia jatkojalostusmahdollisuuksia, joilla voidaan nostaa suuren mäntysahan tuotteiston arvoa. Lisäksi tuli tarkastella jalostuksen integrointia sahan tuotantoprosessiin. Työn taustalla on toisaalta puutuotemarkkinoiden muuttuminen ja toisaalta raaka-aineen laadullinen huononeminen. Molemmat seikat vaikuttavat negatiivisesti perinteisen mäntysahan kannattavuuteen .Jatkojalostuksen integroinnilla sahatavaraprosessiin saavutetaan säästöjä tuotantokustannuksissa, kun tarkastellaan koko prosessia tukista jatkojalosteeksi. Myös raaka-aineen tuottavuutta voidaan nostaa integraation avulla. Jatkojalostus voidaan integroida sahatavaraprosessiin raaka-aineen valikoinnilla sahatavaraprosessin eri osissa, on-line –jalostuksella sekä taloudellisesti. Sahatavaraprosessissa tapahtuva raaka-aineen valikointi voidaan suorittaa tukeista ja sahatavarasta. Valikointikriteerinä voi olla puun ominaisuudet, sahatavaran mitat ja laatu. Valikointiin voidaan nykyteknologiasta hyödyntää röntgentekniikkaa sekä konenäköä. On-line –jalostus tarkoittaa kiinteästi sahatavaraprosessiin liittyvää jalostusta, jolloin ns. turhia prosessivaiheita jää pois ja syntyy säästöjä. On-line –jalostuksen edellytys on raaka-aineen jonkin asteinen valikointi, esim. pituus. Taloudellisesti integroitu jalostus tarkoittaa, että jalostuslaitoksella pyritään nollatulokseen ja jalostuksen lisäarvo palautetaan sahan toimittamaan raaka-aineen hintaan. Tällainen toiminta yhtiön sisällä poistaa turhaa keskustelua raaka-aineen siirtohinnoista ja siten vapauttaa osaltaan resursseja tuottavampaan toimintaan. Erilaisten jatkojalostusmuotojen ja puun ominaisuuksien hyödyntämisen seulonnan perusteella löytyi yksi jalostusmuoto, jolla voidaan kohottaa mäntysahan tuotteiston arvoa. Työn tuloksena syntyi investointiehdotus aihiotankotuotannosta ikkunateollisuuden tarpeisiin. Raaka-aineen hyödynnettäviä ominaisuuksia ovat männyn sydänpuun luonnollinen kestävyys sekä keskimääräinen oksaväli. Valikointi tehdään välitukeista, joiden sahaamisen kannattavuus on männyn rungon osista heikoin. Aihiotankoprosessissa hyödynnetään konenäköä ja sormijatkostekniikkaa. Jatkojalostuksen integrointi sahatavaraprosessiin toteutetaan rakentamalla on-line –jalostuslaitos sekä soveltamalla röntgentekniikkaa raaka-aineen valinnassa.

Examining the Role of Rebranding in Perceived Image of a Product Line

The main objective for this study was to explore certain organization’s product line rebranding process and its impact on product line’s perceived image. The case company is a global paper, packaging and forest products company, business segment paper board. The audience explored is one of the company’s major customers, merchant in Germany. The research was performed as a descriptive case study with a purpose to provide longitudinal insight into the product line image and its eventual alteration as a result of the case company’s rebranding process. Mainly qualitative methods were used for conducting the research. The data for the empirical part was collected with a web-based survey at two different points of time; before the rebranded products entered the market and after they had been available approximately six months. The results of this study reveal that the case company has performed well in its attempt to improve product line’s brand image through rebranding. It was found that between the two brand image measurements the product brand image seems to have improved in all of the areas which according to theoretical framework of this study contribute to formation of brand image; brand associations, marketing communications and interpersonal relationships, not forgetting the original platform that initiated the change; technical quality modifications. In other words it may be concluded that as technical quality was brought to a new level, also assessments about the brand image improved respectively.

Spontaneous canine transmissible venereal tumor: association between different phenotypes and the insertion LINE-1/c-myc

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Tumor venéreo transmissível espontâneo canino: a inserção do transposon line-1 no gene C-MYC e os critérios de malignidade

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A simple high-performance liquid chromatography assay for on-line determination of catecholamines in adrenal gland by direct injection on an ISRP column

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Results from the HST/COS FUV detector "lifetime move"

We describe the planning, implementation, and initial results of the first planned move of the default position of spectra on the Hubble Space Telescope's Cosmic Origins Spectrograph (COS) Far Ultraviolet (FUV) cross-delay line detector. This was motivated by the limited amount of charge that can be extracted from the microchannel plate due to gain sag at any one position. Operations at a new location began on July 23, 2012, with a shift of the spectrum by +3.5"(corresponding to ~ 41 pixels or ~ 1 mm) in a direction orthogonal to the spectral dispersion. Operation at this second "lifetime position" allows for spectra to be collected which are not affected by detector artifacts and loss of sensitivity due to gain sag. We discuss programs designed to enable operations at the new lifetime position; these include determinations of operational high voltage, measuring walk corrections and focus, confirming spectrum placement and aperture centering, and target acquisition performance. We also present results related to calibration of the new lifetime position, including measurements of spectral resolution and wavelength calibration, flux and flat field calibration, carryover of time-dependent sensitivity monitoring, and operations with the Bright Object Aperture (BOA).

Synthese und Charakterisierung von Poly(tert-butylacrylat)- und Polyacrylsäure-Sternpolymeren

Sternpolymere aus Poly(tert.-butylacrylat)-Armen und einem Mikrogel-Core aus Ethylenglykoldimethacrylat wurden nach der arm-first Strategie hergestellt. Diese weisen eine enge Armzahlverteilung auf. Mit sinkender Precursorlänge, mit steigendem Verhältnis [bifunktionelles Monomer]/[Initiator], sowie mit zunehmender Reaktionszeit und Gesamtkonzentration nimmt die mittlere Armzahl fn zu. Die Sternbildung verläuft ähnlich einer Polykondensation. Die Molekulargewichte wurden mittels GPC gekoppelt mit einem online-Viskosimeter und einem online-Vielwinkellichtstreudetektor (MALLS) bestimmt.Die intrinsischen Viskositäten der Sternpolymere sind sehr niedrig. Für Armzahlen f ca. 8 erhält man ein Maximum in der doppellogarithmischen Auftragung der intrinsischen Viskosität und des Molekulargewichts. Die Trägheitsradien nehmen nur wenig mit dem Molekulargewicht zu. Die erhaltenen Koeffizienten liegen im von Daoud und Cotton vorhergesagten Bereich. Die Schrumpfungsfaktoren sinken auf g ca. 0,2 bzw. g' ca. 0,25. Aus den Poly(tert.-butylacrylat)-Sternpolymeren wurden durch Verseifung mit HBr in Methanol Polyacrylsäure-Sternpolymere hergestellt, welche ebenfalls mittels GPC-Viskosimetrie und GPC-MALLS charakterisiert wurden. Für die ionischen Sternpolymere findet man deutlich höhere Schrumpfungsfaktoren, kein Maximum in der intrinsischen Viskosität und höhere Exponenten als von Daoud und Cotton vorhergesagt. Erklärt wurde dies mit der hohen Segmentdichte in Sternpolymeren, die bei den ionischen Sternpolymeren zu einer hohen Ladungsdichte führt. Dadurch müssen sich die Arme stärker strecken als bei nicht-ionischen Sternen und es resultieren größere Moleküldimensionen.

Luminosity measurements with the LUCID detector in the ATLAS experiment

La misura della luminosità è un obiettivo importante per tutta la fisica del modello standard e per la scoperta di nuova fisica, poiché è legata alla sezione d'urto (σ) e al rate di produzione (R) di un determinato processo dalla relazione L = R*σ. Nell'eserimento ATLAS a LHC è installato un monitor di luminosità dedicato chiamato LUCID (Luminosity measurements Using Cherenkov Integrating Detector). Grazie ai dati acquisiti durante il 2010 la valutazione off-line delle performances del LUCID e l'implementazione di controlli on-line sulla qualità dei dati raccolti è stata possibile. I dati reali sono stati confrontati con i dati Monte Carlo e le simulazioni sono state opportunamente aggiustate per ottimizzare l'accordo tra i due. La calibrazione della luminosità relativa che permette di ottenere una valutazione della luminosità assoluta è stata possibile grazie ai cosiddetti Van der Meer scan, grazie ai quale è stata ottenuta una precisione dell'11%. L'analisi della fisica del decadimento della Z è in tuttora in corso per ottenere tramite il rate a cui avviene il processo una normalizzazione della luminosità con una precisione migliore del 5%.

"En face" OCT imaging of the IS/OS junction line in type 2 idiopathic macular telangiectasia

We investigated abnormalities of the photoreceptor inner/outer segment (IS/OS) junction layer viewed "en face" and their functional correlates in type 2 idiopathic macular telangiectasia (type 2 MacTel).

In-situ measurement and characterization of cloud particles using digital in-line holography

Satellite measurement validations, climate models, atmospheric radiative transfer models and cloud models, all depend on accurate measurements of cloud particle size distributions, number densities, spatial distributions, and other parameters relevant to cloud microphysical processes. And many airborne instruments designed to measure size distributions and concentrations of cloud particles have large uncertainties in measuring number densities and size distributions of small ice crystals. HOLODEC (Holographic Detector for Clouds) is a new instrument that does not have many of these uncertainties and makes possible measurements that other probes have never made. The advantages of HOLODEC are inherent to the holographic method. In this dissertation, I describe HOLODEC, its in-situ measurements of cloud particles, and the results of its test flights. I present a hologram reconstruction algorithm that has a sample spacing that does not vary with reconstruction distance. This reconstruction algorithm accurately reconstructs the field to all distances inside a typical holographic measurement volume as proven by comparison with analytical solutions to the Huygens-Fresnel diffraction integral. It is fast to compute, and has diffraction limited resolution. Further, described herein is an algorithm that can find the position along the optical axis of small particles as well as large complex-shaped particles. I explain an implementation of these algorithms that is an efficient, robust, automated program that allows us to process holograms on a computer cluster in a reasonable time. I show size distributions and number densities of cloud particles, and show that they are within the uncertainty of independent measurements made with another measurement method. The feasibility of another cloud particle instrument that has advantages over new standard instruments is proven. These advantages include a unique ability to detect shattered particles using three-dimensional positions, and a sample volume size that does not vary with particle size or airspeed. It also is able to yield two-dimensional particle profiles using the same measurements.