A gated single-photon avalanche diode array fabricated in a conventional CMOS process for triggered systems

A bidimensional array based on single-photon avalanche diodes for triggered imaging systems is presented. The diodes are operated in the gated mode of acquisition to reduce the probability to detect noise counts interfering with photon arrival events. In addition, low reverse bias overvoltages are used to lessen the dark count rate. Experimental results demonstrate that the prototype fabricated with a standard HV-CMOS process gets rid of afterpulses and offers a reduced dark count probability by applying the proposed modes of operation. The detector exhibits a dynamic range of 15 bits with short gated"on" periods of 10ns and a reverse bias overvoltage of 1.0V.

Avoiding sensor blindness in Geiger mode avalanche photodiode arrays fabricated in a conventional CMOS process

The need to move forward in the knowledge of the subatomic world has stimulated the development of new particle colliders. However, the objectives of the next generation of colliders sets unprecedented challenges to the detector performance. The purpose of this contribution is to present a bidimensional array based on avalanche photodiodes operated in the Geiger mode to track high energy particles in future linear colliders. The bidimensional array can function in a gated mode to reduce the probability to detect noise counts interfering with real events. Low reverse overvoltages are used to lessen the dark count rate. Experimental results demonstrate that the prototype fabricated with a standard HV-CMOS process presents an increased efficiency and avoids sensor blindness by applying the proposed techniques.

Readout schemes for low noise single-photon avalanche diodes fabricated in conventional HV-CMOS technologies

Three different pixels based on single-photon avalanche diodes for triggered applications, such as fluorescence lifetime measurements and high energy physics experiments, are presented. Each pixel consists of a 20µm x 100µm (width x length) single photon avalanche diode and a monolithically integrated readout circuit. The sensors are operated in the gated mode of acquisition to reduce the probability to detect noise counts interferring with real radiation events. Each pixel includes a different readout circuit that allows to use low reverse bias overvoltages. Experimental results demonstrate that the three pixels present a similar behaviour. The pixels get rid of afterpulses and present a reduced dark count probability by applying the gated operation. Noise figures are further improved by using low reverse bias overvoltages. The detectors exhibit an input dynamic range of 13.35 bits with short gated"on" periods of 10ns and a reverse bias overvoltage of 0.5V. The three pixels have been fabricated in a standard HV-CMOS process.

Readout electronics for low dark count pixel detectors based on geiger mode avalanche photodiodes fabricated in conventional CMOS technologies for future linear colliders

The high sensitivity and excellent timing accuracy of Geiger mode avalanche photodiodes makes them ideal sensors as pixel detectors for particle tracking in high energy physics experiments to be performed in future linear colliders. Nevertheless, it is well known that these sensors suffer from dark counts and afterpulsing noise, which induce false hits (indistinguishable from event detection) as well as an increase of the necessary area of the readout system. In this work, we present a comparison between APDs fabricated in a high voltage 0.35 µm and a high integration 0.13 µm commercially available CMOS technologies that has been performed to determine which of them best fits the particle collider requirements. In addition, a readout circuit that allows low noise operation is introduced. Experimental characterization of the proposed pixel is also presented in this work.

Low dark count geiger mode avalanche photodiodes fabricated in conventional CMOS technologies

Avalanche photodiodes operated in the Geiger mode present very high intrinsic gain and fast time response, which make the sensor an ideal option for those applications in which detectors with high sensitivity and velocity are required. Moreover, they are compatible with conventional CMOS technologies, allowing sensor and front-end electronics integration within the pixel cell. Despite these excellent qualities, the photodiode suffers from high intrinsic noise, which degrades the performance of the detector and increases the memory area to store the total amount of information generated. In this work, a new front-end circuit that allows low reverse bias overvoltage sensor operation to reduce the noise in Geiger mode avalanche photodiode pixel detectors is presented. The proposed front-end circuit also enables to operate the sensor in the gated acquisition mode to further reduce the noise. Experimental characterization of the fabricated pixel with the conventional HV-AMS 0.35µm technology is also presented in this article.

Prosessit palveluiden kehittämisen tukena pienessä tietointensiivisessä palveluyrityksessä Case: Integrata Oy

Palvelut ovat nousseet lähes kiinteäksi osaksi tuotteita sekä niiden rinnalle omaksi liiketoiminta-alueekseen. Tämän vuoksi palveluiden kehittäminen on viime vuosikymmeninä noussut sekä yritysten että akateemisten yhteisöjen mielenkiinnonkohteeksi. Menestyksekäs palveluiden kehittäminen vaatii usein systemaattisia menetelmiä, mutta menetelmien tulee antaa tilaa myös tarkoituksenmukaisille poikkeamille. Kohdeyritys pyrkii tuottamaan laadukkaita palveluita asiakastarpeet huomioiden. Tämän takia yritys haluaa kehittää olemassa olevia palveluita jatkuvasti ja pyrkii keräämään sekä työntekijöiltä että asiakkailta tietoa palvelutarpeista, joista voidaan lähteä kehittämään uusia palvelukokonaisuuksia. Tutkimus pyrkii havainnoimaan kohdeyrityksen palveluiden kehitystä ja tavoitteena on muodostaa havaintojen perusteella prosessin, jota yritys voi jatkossa hyödyntää sekä edelleen kehittää. Tutkimus on kehittävä tapaustutkimus, jonka teoreettisen viitekehyksen muodostavat uusien palveluiden kehittämisen - ja palveluinnovaatioprosessien näkökulmat. Yrityksen palveluiden kehitystä tarkastellaan kahden primaarisen aineiston sekä kahden sekundaarisen aineiston kautta. Näin ollen palveluiden kehitystä voidaan tarkastella useista näkökulmista käyttäen menetelmänä aineistotriangulaatiota. Tutkimuksessa havaittiin, että kohdeyrityksen palveluiden kehitysprosessi muodostui hyvin vastaavanlaiseksi kuin teoriaosuudessa esitettyjen uusien palveluiden kehitys- ja palveluinnovaatioprosessit. Asiakkaita ja työntekijöitä osallistettiin jonkin verran prosessin aikana. Lisäksi havaittiin, että uusien palveluiden kehitys- ja palveluinnovaatioprosessit eivät ehkä ole erillisiä kehitysprosesseja, vaikka niistä käytetäänkin eri nimityksiä kirjallisuudessa.

Potential and Challenges of Analog Reconfigurable Computation in Modern and Future CMOS

In this work, the feasibility of the floating-gate technology in analog computing platforms in a scaled down general-purpose CMOS technology is considered. When the technology is scaled down the performance of analog circuits tends to get worse because the process parameters are optimized for digital transistors and the scaling involves the reduction of supply voltages. Generally, the challenge in analog circuit design is that all salient design metrics such as power, area, bandwidth and accuracy are interrelated. Furthermore, poor flexibility, i.e. lack of reconfigurability, the reuse of IP etc., can be considered the most severe weakness of analog hardware. On this account, digital calibration schemes are often required for improved performance or yield enhancement, whereas high flexibility/reconfigurability can not be easily achieved. Here, it is discussed whether it is possible to work around these obstacles by using floating-gate transistors (FGTs), and analyze problems associated with the practical implementation. FGT technology is attractive because it is electrically programmable and also features a charge-based built-in non-volatile memory. Apart from being ideal for canceling the circuit non-idealities due to process variations, the FGTs can also be used as computational or adaptive elements in analog circuits. The nominal gate oxide thickness in the deep sub-micron (DSM) processes is too thin to support robust charge retention and consequently the FGT becomes leaky. In principle, non-leaky FGTs can be implemented in a scaled down process without any special masks by using “double”-oxide transistors intended for providing devices that operate with higher supply voltages than general purpose devices. However, in practice the technology scaling poses several challenges which are addressed in this thesis. To provide a sufficiently wide-ranging survey, six prototype chips with varying complexity were implemented in four different DSM process nodes and investigated from this perspective. The focus is on non-leaky FGTs, but the presented autozeroing floating-gate amplifier (AFGA) demonstrates that leaky FGTs may also find a use. The simplest test structures contain only a few transistors, whereas the most complex experimental chip is an implementation of a spiking neural network (SNN) which comprises thousands of active and passive devices. More precisely, it is a fully connected (256 FGT synapses) two-layer spiking neural network (SNN), where the adaptive properties of FGT are taken advantage of. A compact realization of Spike Timing Dependent Plasticity (STDP) within the SNN is one of the key contributions of this thesis. Finally, the considerations in this thesis extend beyond CMOS to emerging nanodevices. To this end, one promising emerging nanoscale circuit element - memristor - is reviewed and its applicability for analog processing is considered. Furthermore, it is discussed how the FGT technology can be used to prototype computation paradigms compatible with these emerging two-terminal nanoscale devices in a mature and widely available CMOS technology.

A Comaparison Study of EM and Physical Equivalent Circuit Modeling for MIM CMOS Capacitors

In this Letter a new physical model for metal-insulatormetal CMOS capacitors is presented. In the model the parameters of the circuit are derived from the physical structural details. Physical behaviors due to metal skin effect and inductance have been considered. The model has been confirmed by 3D EM simulator and design rules proposed. The model presented is scalable with capacitor geometry, allowing designers to predict and optimize quality factor. The approach has been verified for MIM CMOS capacitors

Equipos didácticos multimedia para la enseñanza de las famílias lógicas : pmos, nmos y cmos.

En el día a día del aula universitaria, se ha hecho necesario el uso de diferente material de apoyo a la docencia. Para el estudio en profundidad de la familia Mos, se ha desarrollado un libro teórico y uno de los complementos con unos programas tutores de elaboración propia que ofrecen al estudiante un nuevo punto de vista basaso en la interactividad para ayudar a comprenderlos y sirviéndose, al mismo tiempo, de tutoría y autoevaluación.

WTROPIC : um gerador automático de macro células CMOS acessível via WWW

Este trabalho apresenta a pesquisa e o desenvolvimento da ferramenta para geração automática de leiautes WTROPIC. O WTROPIC é uma ferramenta para a geração remota, acessível via WWW, de leiautes para circuitos CMOS adequada ao projeto FUCAS e ao ambiente CAVE. O WTROPIC foi concebido a partir de otimizações realizadas na versão 3 da ferramenta TROPIC. É mostrado também, como as otimizações no leiaute do TROPIC foram implementadas e como essas otimizações permitem ao WTROPIC cerca de 10% de redução da largura dos circuitos gerados em comparação ao TROPIC. Como o TROPIC, o WTROPIC é um gerador de macro células CMOS independente de biblioteca. Apresenta-se também, como a ferramenta WTROPIC foi integrada ao ambiente de concepção de circuitos CAVE, as mudanças propostas para metodologia de integração de ferramentas do CAVE que conduzem a uma melhora na qualidade de integração e a padronização das interfaces de usuário e como a síntese física de um leiaute pode ser então realizada remotamente. Dessa maneira, obteve-se uma ferramenta para a concepção de leiautes disponível a qualquer usuário com acesso a internet, mesmo que esse usuário não disponha de uma máquina com elevada capacidade de processamento, normalmente exigido por ferramentas de CAD.

Estimativa de capacitâncias e consumo de potência em circuitos combinacionais CMOS no nível lógico

Esta tese propõe o desenvolvimento de um método de estimativa de capacitâncias e de potência consumida nos circuitos combinacionais CMOS, no nível de portas lógicas. O objetivo do método é fazer uma previsão do consumo de potência do circuito na fase de projeto lógico, o que permitirá a aplicação de técnicas de redução de potência ou até alteração do projeto antes da geração do seu leiaute. A potência dinâmica consumida por circuitos CMOS depende dos seguintes parâmetros: tensão de alimentação, freqüência de operação, capacitâncias parasitas e atividades de comutação em cada nodo do circuito. A análise desenvolvida na Tese, propõe que a potência seja dividida em duas componentes. A primeira componente está relacionada ao consumo de potência devido às capacitâncias intrínsecas dos transistores, que por sua vez estão relacionadas às dimensões dos transistores. Estas capacitâncias intrínsecas são concentradas nos nodos externos das portas e manifestam-se em função das combinações dos vetores de entrada. A segunda componente está relacionada às interconexões entre as células do circuito. Para esta etapa utiliza-se a estimativa do comprimento médio das interconexões e as dimensões tecnológicas para estimar o consumo de potência. Este comprimento médio é estimado em função do número de transistores e fanout das várias redes do circuito. Na análise que trata das capacitâncias intrínsecas dos transistores os erros encontrados na estimativa da potência dissipada estão no máximo em torno de 11% quando comparados ao SPICE. Já na estimativa das interconexões a comparação feita entre capacitâncias de interconexões estimadas no nível lógico e capacitâncias de interconexões extraídas do leiaute apresentou erros menores que 10%.

Automatic layout generation of static CMOS circuits targeting delay and power

The evolution of integrated circuits technologies demands the development of new CAD tools. The traditional development of digital circuits at physical level is based in library of cells. These libraries of cells offer certain predictability of the electrical behavior of the design due to the previous characterization of the cells. Besides, different versions of each cell are required in such a way that delay and power consumption characteristics are taken into account, increasing the number of cells in a library. The automatic full custom layout generation is an alternative each time more important to cell based generation approaches. This strategy implements transistors and connections according patterns defined by algorithms. So, it is possible to implement any logic function avoiding the limitations of the library of cells. Tools of analysis and estimate must offer the predictability in automatic full custom layouts. These tools must be able to work with layout estimates and to generate information related to delay, power consumption and area occupation. This work includes the research of new methods of physical synthesis and the implementation of an automatic layout generation in which the cells are generated at the moment of the layout synthesis. The research investigates different strategies of elements disposition (transistors, contacts and connections) in a layout and their effects in the area occupation and circuit delay. The presented layout strategy applies delay optimization by the integration with a gate sizing technique. This is performed in such a way the folding method allows individual discrete sizing to transistors. The main characteristics of the proposed strategy are: power supply lines between rows, over the layout routing (channel routing is not used), circuit routing performed before layout generation and layout generation targeting delay reduction by the application of the sizing technique. The possibility to implement any logic function, without restrictions imposed by a library of cells, allows the circuit synthesis with optimization in the number of the transistors. This reduction in the number of transistors decreases the delay and power consumption, mainly the static power consumption in submicrometer circuits. Comparisons between the proposed strategy and other well-known methods are presented in such a way the proposed method is validated.

Design of boundary-scan testing in CMOS image sensors for industrial applications: internship repor

Tests on printed circuit boards and integrated circuits are widely used in industry,resulting in reduced design time and cost of a project. The functional and connectivity tests in this type of circuits soon began to be a concern for the manufacturers, leading to research for solutions that would allow a reliable, quick, cheap and universal solution. Initially, using test schemes were based on a set of needles that was connected to inputs and outputs of the integrated circuit board (bed-of-nails), to which signals were applied, in order to verify whether the circuit was according to the specifications and could be assembled in the production line. With the development of projects, circuit miniaturization, improvement of the production processes, improvement of the materials used, as well as the increase in the number of circuits, it was necessary to search for another solution. Thus Boundary-Scan Testing was developed which operates on the border of integrated circuits and allows testing the connectivity of the input and the output ports of a circuit. The Boundary-Scan Testing method was converted into a standard, in 1990, by the IEEE organization, being known as the IEEE 1149.1 Standard. Since then a large number of manufacturers have adopted this standard in their products. This master thesis has, as main objective: the design of Boundary-Scan Testing in an image sensor in CMOS technology, analyzing the standard requirements, the process used in the prototype production, developing the design and layout of Boundary-Scan and analyzing obtained results after production. Chapter 1 presents briefly the evolution of testing procedures used in industry, developments and applications of image sensors and the motivation for the use of architecture Boundary-Scan Testing. Chapter 2 explores the fundamentals of Boundary-Scan Testing and image sensors, starting with the Boundary-Scan architecture defined in the Standard, where functional blocks are analyzed. This understanding is necessary to implement the design on an image sensor. It also explains the architecture of image sensors currently used, focusing on sensors with a large number of inputs and outputs.Chapter 3 describes the design of the Boundary-Scan implemented and starts to analyse the design and functions of the prototype, the used software, the designs and simulations of the functional blocks of the Boundary-Scan implemented. Chapter 4 presents the layout process used based on the design developed on chapter 3, describing the software used for this purpose, the planning of the layout location (floorplan) and its dimensions, the layout of individual blocks, checks in terms of layout rules, the comparison with the final design and finally the simulation. Chapter 5 describes how the functional tests were performed to verify the design compliancy with the specifications of Standard IEEE 1149.1. These tests were focused on the application of signals to input and output ports of the produced prototype. Chapter 6 presents the conclusions that were taken throughout the execution of the work.

A multisampling time-domain CMOS imager with synchronous readout circuit

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Winner-take-all circuit using CMOS technology

In this paper is presented an implementation of winner-take-all circuit using CMOS technology. In the proposed configuration the inputs are current and the outputs voltage. The simulation results show that the circuit can be a winner if its input is larger than the other by 2 mu A. The simulation also shows that the response time is 100ns at a 0.2pF load capacitance. To demonstrate the functionality of the proposed circuit, a two-input winner take all circuit was built and tested by using discrete CMOS transistor array (CD40071).