Design of a compact wideband bandpass filter

This article presents the analysis and design of a compact multi-layer layer, high selectivity wideband bandpass filter using stub loaded and `U' shaped resonators over a slotted bottom ground plane. While the resonators with folded open circuit stub loadings create the desired bandpass characteristics. the IT shaped resonators reduce the size of filter. The slotted bottom ground plane is used to enhance the coupling to achieve the desired bandwidth. The proposed filter has been analyzed using circuit model, and the results were verified through full wave simulations and measurements. The fabricated filter is compact and measures a size of 18 mm x 25 mm x 1.6 MM. (C) 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52: 1387-1389, 2010: Published online in Wiley InterScience (www.interscience.wiley.com).

Ce0.78Sn0.2Pt0.02O2-delta: A new non-deactivating catalyst for hydrogen production via water-gas shift reaction

We demonstrate the activity of Ce0.78Sn0.2Pt0.02O2-delta, a new catalyst, towards water-gas shift (WGS) reaction. Over 99.5% CO conversion to H-2 is observed at 300 +/- 25 degrees C. Based on different characterization techniques we found that the present catalyst is resistant to deactivation due to carbonate formation and sintering of Pt on the surface when subjected to longer duration of reaction conditions. The catalyst does not require any pre-treatment or activation between start-up/shut-down reaction operations. Formation of side products such as methane, methanol, formaldehyde, coke etc. was not observed under the WGS reaction conditions indicating the high selectivity of the catalyst for H-2. Temperature programmed reduction of the catalyst in hydrogen (H-2-TPR) shows reversible reduction of Ce4+ to Ce3+, Sn4+ to Sn2+ and Pt4+ to Pt-0 oxidation state with oxygen storage capacity (OSC) of 3500 mu mol g(-1) at 80 degrees C. Such high value of OSC indicates the presence of highly activated lattice oxygen. CO oxidation in presence of stoichiometric O-2 shows 100% conversion to CO2 at room temperature. The catalyst also exhibits 100% selectivity for CO2 at room temperature towards preferential oxidation (PROX) of residual CO in presence of excess hydrogen in the feed. (C) 2010 Elsevier B.V. All rights reserved.

Fluorescence and visual sensing of nitroaromatic explosives using electron rich discrete fluorophores

Several pi-electron rich fluorescent aromatic compounds containing trimethylsilylethynyl functionality have been synthesized by employing Sonogashira coupling reaction and they were characterized fully by NMR (H-1, C-13)/IR spectroscopy. Incorporation of bulky trimethylsilylethynyl groups on the peripheral of the fluorophores prevents self-quenching of the initial intensity through pi-pi interaction and thereby maintains the spectroscopic stability in solution. These compounds showed fluorescence behavior in chloroform solution and were used as selective fluorescence sensors for the detection of electron deficient nitroaromatics. All these fluorophores showed the largest quenching response with high selectivity for nitroaromatics among the various electron deficient aromatic compounds tested. Quantitative analysis of the fluorescence titration profile of 9,10-bis(trimethylsilylethynyl) anthracene with picric acid provided evidence that this particular fluorophore detects picric acid even at ppb level. A sharp visual detection of 2,4,6-trinitrotoluene was observed upon subjecting 1,3,6,8-tetrakis (trimethylsilylethynyl) pyrene fluorophore to increasing quantities of 2,4,6-trinitrotoluene in chloroform. Furthermore, thin film of the fluorophores was made by spin coating of a solution of 1.0 x 10(-3) M in chloroform or dichloromethane on a quartz plate and was used for the detection of vapors of nitroaromatics at room temperature. The vapor-phase sensing experiments suggested that the sensing process is reproducible and quite selective for nitroaromatic compounds. Selective fluorescence quenching response including a sharp visual color change for nitroaromatics makes these fluorophores as promising fluorescence sensory materials for nitroaromatic compounds (NAC) with a detection limit of even ppb level as judged with picric acid.

Self-Assembly of Metallamacrocycles Using a Dinuclear Organometallic Acceptor: Synthesis, Characterization, and Sensing Study

A dinuclear organometallic acceptor 4,4'-bis[trans-Pt(PEt(3))(2)(O(3)SCF(3))(ethynyl)]biphenyl (1) containing Pt-ethynyl functionality is synthesized. Multinuclear NMR ((1)H, (31)P, and (13)C), infrared (IR), and electrospray ionization mass spectrometry (ESI-MS) including single-crystal X-ray diffraction analysis established the formation of 1. Equimolar treatment of acceptor 1 separately with three different ``clip'' type ditopic donors (L(a)-L(c)) yielded [2 + 2] self-assembled three metallamacrocycles 2a-2c, respectively. These macrocycles were characterized by various spectroscopic techniques, and their sizes/shapes were obtained through geometry optimization using molecular mechanics universal force field (MMUFF) simulations. Attachment of unsaturated ethynyl functionality to biphenyl building unit helped to make the macrocycles (2a-2c) pi-electron rich and thereby fluorescent in nature. Furthermore, 2c in solution has been examined to be suitable for sensing electron-deficient nitroaromatic like picric acid, which is often considered as a secondary chemical explosive. The fluorescence study of 2c showed a marked quenching of initial emission intensity upon titrating with picric acid (PA), and it exhibited the largest fluorescence quenching response with high selectivity among various other electron deficient aromatic compounds tested.

Coordination-driven self-assembly of 2D-metallamacrocycles using a shape-selective Pt(2)(II)-organometallic 90 degrees acceptor: design, synthesis and sensing study

Synthesis of a series of two-dimensional metallamacrocycles via coordination-driven self-assembly of a shape-selective Pt(2)(II)-molecular building unit incorporating carbazole-ethynyl functionality is described. An equimolar (1 : 1) combination of a Pt(2)(II)-organometallic 90 degrees acceptor, 1, with rigid linear ditopic donors (L(a) and L(b)) afforded [4 + 4] self-assembled octanuclear molecular squares, 2 and 3, in quantitative yields, respectively [L(a) = 4,4'-bipyridine; L(b) = trans-1,2-bis(4-pyridyl)ethylene]. Conversely, a similar treatment of 1 with an amide-based unsymmetrical flexible ditopic donor, L(c), resulted in the formation of a [2 + 2] self-sorted molecular rhomboid (4a) as a single product [L(c) = N-(4-pyridyl)isonicotinamide]. Despite the possibility of several linkage isomeric macrocycles (rhomboid, triangle and square) due to the different connectivity of L(c), the formation of a single and symmetrical molecular rhomboid (4a) as the only product is an interesting observation. All the self-assembled macrocycles (2, 3 and 4a) were fully characterized by multinuclear NMR ((1)H and (31)P) and ESI-MS analysis. Further structural insights about the size and shape of the macrocycles were obtained through energy minimization using density functional theory (DFT) calculations. Decoration of the starting carbazole building unit with Pt-ethynyl functionality enriches the assemblies to be more p-electron rich and luminescent in nature. Macrocycles 2 and 3 could sense the presence of electron deficient nitroaromatics in solution by quenching of the initial intensity upon gradual addition of picric acid (PA). They exhibited the largest quenching response with high selectivity for nitroaromatics compared to several other electron deficient aromatics tested.

Selective colorimetric detection of nanomolar Cr (VI) in aqueous solutions using unmodified silver nanoparticles

In this study we present a colorimetric detection method for Cr (VI) in aqueous solution based on as synthesized silver nanoparticles (Ag NPs) without surface functionalization. The method principle involves reduction of Cr (VI) to Cr (III) by excess reductant present in as synthesized Ag NP dispersion, and subsequent aggregation of Ag NPs by Cr (III) leading to red-shift of the surface plasmon resonance (SPR) peak. The UV-vis absorption spectra. Zeta potentials, dynamic light scattering measurements, and scanning electron microscopy (SEM) confirmed the aggregation of the Ag NPs. Under the optimized conditions, a good linear relationship (correlation coefficient r=0.981) was obtained between the ratio of the absorbance at 550 nm to that at 390 nm (A(550/390)) and the concentration of Cr (VI) over the range of 10(-3)-10(-9) M 50 mg/L to 50 ng/L]. The reported probe has a limit of detection down to 1 nM, which, to the best of our knowledge, is the lowest ever reported for the colorimetric detection of Cr (VI). Furthermore, a remarkable feature of this method is that it involves a simple technique exhibiting high selectivity to Cr (VI) over other tested heavy metal ions. (C) 2012 Elsevier BM. All rights reserved.

An Efficient Probe for Rapid Detection of Cyanide in Water at Parts per Billion Levels and Naked-Eye Detection of Endogenous Cyanide

A new molecular probe based on an oxidized bis-indolyl skeleton has been developed for rapid and sensitive visual detection of cyanide ions in water and also for the detection of endogenously bound cyanide. The probe allows the naked-eye detection of cyanide ions in water with a visual color change from red to yellow ((max)=80nm) with the immediate addition of the probe. It shows high selectivity towards the cyanide ion without any interference from other anions. The detection of cyanide by the probe is ratiometric, thus making the detection quantitative. A Michael-type addition reaction of the probe with the cyanide ion takes place during this chemodosimetric process. In water, the detection limit was found to be at the parts per million level, which improved drastically when a neutral micellar medium was employed, and it showed a parts-per-billion-level detection, which is even 25-fold lower than the permitted limits of cyanide in water. The probe could also efficiently detect the endogenously bound cyanide in cassava (a staple food) with a clear visual color change without requiring any sample pretreatment and/or any special reaction conditions such as pH or temperature. Thus the probe could serve as a practical naked-eye probe for in-field experiments without requiring any sophisticated instruments.

Amide Functionalized Microporous Organic Polymer (Am-MOP) for Selective CO2 Sorption and Catalysis

We report the design and synthesis of an amide functionalized microporous organic polymer (Am-MOP) prepared from trimesic acid and p-phenylenediamine using thionyl chloride as a reagent. Polar amide (CONH) functional groups act as a linking unit between the node and spacer and constitute the pore wall of the continuous polymeric network. The strong covalent bonds between the building blocks (trimesic acid and p-phenylenediamine) through amide bond linkages provide high thermal and chemical stability to Am-MOP. The presence of a highly polar pore surface allows selective CO2 uptake at 195 K over other gases such as N-2, Ar, and O-2. The CO2 molecule interacts with amide functional groups via Lewis acid base type interactions as demonstrated through DFT calculations. Furthermore, for the first time Am-MOP with basic functional groups has been exploited for the Knoevenagel condensation reaction between aldehydes and active methylene compounds. Availability of a large number of catalytic sites per volume and confined microporosity gives enhanced catalytic efficiency and high selectivity for small substrate molecules.

Multicomponent Assembly of Fluorescent-Tag Functionalized Ligands in Metal-Organic Frameworks for Sensing Explosives

Detection of trace amounts of explosive materials is significantly important for security concerns and pollution control. Four multicomponent metal organic frameworks (MOFs-12, 13, 23, and 123) have been synthesized by employing ligands embedded with fluorescent tags. The multicomponent assembly of the ligands was utilized to acquire a diverse electronic behavior of the MOFs and the fluorescent tags were strategically chosen to enhance the electron density in the MOFs. The phase purity of the MOFs was established by PXRD, NMR spectroscopy, and finally by singlecrystal XRD. Single-crystal structures of the MOFs-12 and 13 showed the formation of three-dimensional porous networks with the aromatic tags projecting inwardly into the pores. These electron-rich MOFs were utilized for detection of ex- plosive nitroaromatic compounds (NACs) through fluorescence quenching with high selectivity and sensitivity. The rate of fluorescence quenching for all the MOFs follows the order of electron deficiency of the NACs. We also showed the detection of picric acid (PA) by luminescent MOFs is not always reliable and can be misleading. This attracts our attention to explore these MOFs for sensing picryl chloride (PC), which is as explosive as picric acid and used widely to prepare more stable explosives like 2,4,6-trinitroaniline from PA. Moreover, the recyclability and sensitivity studies indicated that these MOFs can be reused several times with parts per billion (ppb) levels of sensitivity towards PC and 2,4,6-trinitrotoluene (TNT).

A quinazoline derivative as quick-response red-shifted reporter for nanomolar Al3+ and applicable to living cell staining

A newly synthesized and structurally characterized quinazoline derivative (L) has been shown to act as a quick-response chemosensor for Al3+ with a high selectivity over other metal ions in water-DMSO. In the presence of Al3+, L shows a red-shifted ratiometric enhancement in fluorescence as a result of internal charge transfer and chelation-enhanced fluorescence through the inhibition of a photo-induced electron transfer mechanism. This probe detects Al3+ at concentrations as low as 1.48 nM in 100 mM HEPES buffer (DMSO-water, 1 : 9 v/v) at biological pH with a very short response time (15-20 s). L was applied to biological imaging to validate its utility as a fluorescent probe for monitoring Al3+ ions in living cells, illustrating its value in practical environmental and biological systems.

Multifunctional magnetic reduced graphene oxide dendrites: Synthesis, characterization and their applications

In this paper, for the first time, we have reported the novel synthesis of reduced graphene oxide (r-GO) dendrite kind of nanomaterial. The proposed r-GO dendrite possesses multifunctional properties in various fields of sensing and separation. The dendrite was synthesized by chemical reaction in different steps. Initially, the r-GO sheet was conjugated with silane group modified magnetic nanoparticle, resulting in nanoparticle decorated r-GO. The above r-GO sheet was further reacted with a new r-GO sheet, resulting in the formation of r-GO dendrite type of structure. Multifunctional behavior of this r-GO dendrite structure was studied by different methods. First, magnetic properties were studied by vibrating sample magnetometer (VSM) and it was found that dendrite structure shows good magnetic susceptibility (180.2 emu/g). The proposed r-GO dendrite also shows a very good antibacterial behavior for Escherichia coli and excellent electrochemical behavior towards ferrocyanide probe molecule. Along with these, it also acts as a substrate for the synthesis of molecularly imprinted polymer for europium metal ion, a lanthanide. The proposed imprinted sensor shows a very high selectivity and sensitivity for europium metal ion (limit of detection= 0.019 mu g L-1) in aqueous as well as real samples. (C) 2015 Elsevier B.V. All rights reserved.

A rhodamine-based `turn-on' Al3+ ion-selective reporter and the resultant complex as a secondary sensor for F- ion are applicable to living cell staining

A newly designed fluorescent aluminum(III) complex (L'-Al; 2) of a structurally characterized non-fluorescent rhodamine Schiff base (L) has been isolated in pure form and characterized using spectroscopic and physico-chemical methods with theoretical density functional theory (DFT) support. On addition of Al(III) ions to a solution of L in HEPES buffer (1 mM, pH 7.4; EtOH-water, 1 : 3 v/v) at 25 degrees C, the systematic increase in chelation-enhanced fluorescence (CHEF) enables the detection of Al(III) ions as low as 60 nM with high selectivity, unaffected by the presence of competitive ions. Interestingly, the Al(III) complex (L'-Al; 2) is specifically able to detect fluoride ions by quenching the fluorescence in the presence of large amounts of other anions in the HEPES buffer (1 mM, pH 7.4) at 25 degrees C. On the basis of our experimental and theoretical findings, the addition of Al3+ ions to a solution of L helps to generate a new fluorescence peak at 590 nm, due to the selective binding of Al3+ ions with L in a 1 : 1 ratio with a binding constant (K) of 8.13 x 10(4) M-1. The Schiff base L shows no cytotoxic effect, and it can therefore be employed for determining the intracellular concentration of Al3+ and F-ions by 2 in living cells using fluorescence microscopy.

Boron and Nitrogen Co-doped Carbon Nanoparticles as Photoluminescent Probes for Selective and Sensitive Detection of Picric Acid

Here, we report the synthesis of boron and nitrogen Co-doped carbon nanoparticles (BN-CNPs) by a hydrothermal method using sucrose, boric acid, and urea as the precursors. The BN-CNPs show excellent photoluminescence with a quantum yield of similar to 14.2% in aqueous solution and can be used as photoluminescent probes for selective and sensitive detection of picric acid (PA). PA quenches the photoluminescence signal remarkably, while other explosives cause a little quenching confirming the high selectivity of BN-CNPs. The sensitivity toward PA sensing is high at pH 7 and increases with temperature. The detection limit as well as the sensitivity are shown to improve by adding NaCl to the PA. The low detection limit can be as low as 10 nM at room temperature and pH 7, which indicates the BN-CNPs are superior as compared to other luminescent probes reported in the literature.

Estudo fenotípico e molecular de resistência aos antimicrobianos em amostras clínicas e ambientais de enterobactérias

Buscamos detectar evidências da presença de genes envolvidos na produção de Enzimas Modificadoras de Aminoglicosídeos (EMAs), Beta-lactamases de espectro estendido (ESBLs) e Mecanismos Plasmidiais de Resistência a Quinolonas (PMQRs) em cepas de K. pneumoniae, K. ozaenae e E. coli isoladas de amostras de água de rios afluentes da Baía de Guanabara e de materiais clínicos de origem hospitalar, além de avaliar o "status sanitário" dos corpos aquáticos abordados no tocante à contaminação fecal recente e indicações de contaminação hospitalar e por outros ambientes de alta seletividade. As cepas de materiais clínicos foram selecionadas entre Maio e Julho de 2010, a partir da semeadura em meio de cultura contendo 8g/mL de gentamicina. As amostras de água foram coletadas em Abril e em Julho de 2009. Realizamos testes de colimetria, empregando para tal, a metodologia convencional e outra, na qual adicionamos 32g/mL de cefalotina e 8g/mL de gentamicina aos caldos Lactosado e Escherichia coli (caldo EC), a fim de detectar e quantificar coliformes resistentes. Para o isolamento das cepas empregamos meios de cultura contendo 32g/mL de cefalotina e 8g/mL de gentamicina. As cepas foram identificadas e submetidas a testes de susceptibilidade aos antimicrobianos (TSA), testes presuntivos para presença de ESBLs, extração de DNA plasmidial e ensaios de Reação em Cadeia de Polimerase (PCR) para a detecção dos genes. A utilização de agentes antimicrobianos nos testes de colimetria nos permitiu detectar a presença e quantificar coliformes totais e fecais resistentes nas amostras de água analisadas nos diferentes pontos. O TSA das cepas isoladas de amostras de água exibiu perfis de multirresistência, compatíveis com o de bactérias de origem hospitalar, semelhante ao encontrado nas cepas isoladas de materiais clínicos. Todas as cepas isoladas de amostras de água e 90% das cepas de materiais clínicos apresentaram pelo menos uma banda plasmidial. Os ensaios de PCR evidenciaram a presença de produtos de amplificação para EMAs, ESBLs e PMQRs, sendo que 7,4% das cepas de amostras de água e 20% das cepas de materiais clínicos apresentaram produtos de amplificação para as três classes de antimicrobianos. A realização de testes de colimetria empregando antimicrobianos, como gentamicina e cefalotina, pode ser uma ferramenta adicional importante ao teste convencional, quando o interesse for, o monitoramento e a prevenção de contaminação ambiental, especialmente associada a microrganismos carreando genes de resistência. O uso criterioso de antimicrobianos em atividades de cunho hospitalar e veterinário e medidas no sentido de prevenção de lançamento de esgoto e/ou tratamento dos efluentes, são fundamentais para o controle da disseminação de elementos genéticos de resistência transferíveis entre os microrganismos. A detecção e identificação de microrganismos apresentando elementos de resistência em ambiente extra-hospitalar como em água e solo, em particular, o emprego de testes de colimetria empregando antimicrobianos, se faz necessária, como forma de prevenção e controle de disseminação destes microrganismos com potencial de causar infecções em humanos e outros animais que eventualmente entram em contato com estes ambientes.

Síntese, caracterização e aplicações na desidrogenação oxidativa de propano de materiais tipo hidrotalcita Ni-Mg-Al com diferentes ânions de compensação

Na reação de desidrogenação oxidativa de propano (ODHP), propano reage com oxigênio da superfície de metais de transição para produzir propeno e água, em temperaturas de 300-700C. Porém, o propeno pode facilmente oxidar, formando CO e CO2. Assim, busca-se catalisadores que promovam a seletividade do propeno. Compostos tipo hidrotalcitas estão sendo apontados como catalisadores de grande potencial para a reação. Portanto, o principal objetivo desse trabalho foi sintetizar precursores tipo hidrotalcitas (contendo íons Ni2+, Mg2+ e Al3+ e tereftalato, heptamolibdato e decavanadato como ânions de compensação) para serem testados na reação de desidrogenação oxidativa de propano. Esses precursores foram sintetizados com uma razão Al/(Al+Ni+Mg)=0,5, variando a razão de Ni/Mg. Além disso, realizou-se a troca iônica do tereftalato (TA) por heptamolibdato (Mo7O24) e decavanadato (V10O28). Esses compostos foram calcinados, obtendo-se assim, óxidos mistos de NiMgAl, NiMgAlMo e NiMgAlV que foram testados como catalisadores na reação de ODHP. Para a determinação das propriedades dos catalisadores foram usadas as técnicas de caracterização: DRX, TGA, volumetria de N2, TPR, Raman e FTIR e ICP. Os resultados indicaram que os materiais tipo hidrotalcita foram obtidos com sucesso. No caso dos precursores preparados por troca iônica a cristalinidade foi menor que os da série NiMgAl-TA. Estes mesmos precursores quando calcinados apresentaram áreas muito altas. Nas três séries, os precursores calcinados são constituídos por óxidos mistos como NiO, NiMoO4, Ni2V2O7 cristalinos e espécies de alumínio e magnésio não detectados na DRX. No teste catalítico de ODHP, observou-se que com o aumento da conversão diminuía a seletividade de propeno, para os óxidos mistos que não continham molibdênio. Os catalisadores da série molibdênio foram os que obtiveram melhor desempenho com altas seletividades, mesmo em altas conversões e a série de cujo precursor foi o tereftalato foi a que exibiu maiores conversões, mas com seletividades menores que da série de Mo