Combination of an anaerobic process with O(3), UV and O(3)/UV for cellulose pulp bleaching effluent treatment

Recent studies have shown that partial oxidation by advanced oxidation processes (AOP) is able to transform hard-to-degrade compounds and increase their biodegradability. In this work, anaerobic treatment was followed by ozonation, UV radiation and ozonation in the presence of UV radiation, to treat bleaching effluents from a cellulose kraft Pulp plant. The anaerobic reactor (horizontal anaerobic immobilized Sludge bed, HAISB) was Used as a pretreatment to reduce the efficient organic load before applying ACIP. The ozone treatments were applied in three different pH environments (3, 8 and 10) with retention times of 10, 30, 45 and 60 min. COD and adsorbable organic halogens (AOX) removal efficiencies at the HAISB were approximately 50%, while the BOD removal efficiency reached 80%. Ozonation promoted further removal of AOX and COD so that the combined efficiency reached 96% for AOX and 70% for COD. In the oxidation process, BOD was either removed in small quantities or actually increased, as intended, so that a second biological treatment would be able to complete the treatment. The maximum increase in the BOD(5)/COD ratio (biodegradability indicator) Occurred at pH 8, reaching 104% for ozonation at a dosage of 1540 mg(O3).L(-1). Applying UV radiation alone resulted in lower values: a 34% increase ill the BOD(5)/COD ratio and a 76% AOX removal efficiency. These results indicate that the combination of anaerobic treatment with ozonation or ozonation/UV radiation improves the treatability of cellulose pulp bleaching efficients and that the resulting wastewater is suitable for further biological treatment under aerobic conditions with a low level of toxic compounds from the halogenated family.

Production and properties of xylanases from Aspergillus terricola Marchal and Aspergillus ochraceus and their use in cellulose pulp bleaching

Aspergillus terricola and Aspergillus ochraceus, isolated from Brazilian soil, were cultivated in Vogel and Adams media supplemented with 20 different carbon sources, at 30 A degrees C, under static conditions, for 120 and 144 h, respectively. High levels of cellulase-free xylanase were produced in birchwood or oat spelt xylan-media. Wheat bran was the most favorable agricultural residue for xylanase production. Maximum activity was obtained at 60 A degrees C and pH 6.5 for A. terricola, and 65 A degrees C and pH 5.0 for A. ochraceus. A. terricola xylanase was stable for 1 h at 60 A degrees C and retained 50% activity after 80 min, while A. ochraceus xylanase presented a t (50) of 10 min. The xylanases were stable in an alkali pH range. Biobleaching of 10 U/g dry cellulose pulp resulted in 14.3% delignification (A. terricola) and 36.4% (A. ochraceus). The brightness was 2.4-3.4% ISO higher than the control. Analysis in SEM showed defibrillation of the microfibrils. Arabinase traces and beta-xylosidase were detected which might act synergistically with xylanase.

Xylanases from Aspergillus niger, Aspergillus niveus and Aspergillus ochraceus produced under solid-state fermentation and their application in cellulose pulp bleaching

This study describes the production of xylanases from Aspergillus niveus, A. niger, and A. ochraceus under solid-state fermentation using agro-industrial residues as substrates. Enzyme production was improved using a mixture of wheat bran and yeast extract or peptone. When a mixture of corncob and wheat bran was used, xylanase production from A. niger and A. ochraceus increased by 18%. All cultures were incubated at 30 A degrees C at 70-80% relative humidity for 96 h. For biobleaching assays, 10 or 35 U of xylanase/g dry cellulose pulp were incubated at pH 5.5 for 1 or 2 h, at 55 A degrees C. The delignification efficiency was 20%, the brightness (percentage of ISO) increased two to three points and the viscosity was maintained confirming the absence of cellulolytic activity. These results indicated that the use of xylanases could help to reduce the amount of chlorine compounds used in cellulose pulp treatment.

Production of xylanase by Aspergilli using alternative carbon sources: application of the crude extract on cellulose pulp biobleaching

The ability of xylanolytic enzymes produced by Aspergillus fumigatus RP04 and Aspergillus niveus RP05 to promote the biobleaching of cellulose pulp was investigated. Both fungi grew for 4-5 days in liquid medium at 40A degrees C, under static conditions. Xylanase production was tested using different carbon sources, including some types of xylans. A. fumigatus produced high levels of xylanase on agricultural residues (corncob or wheat bran), whereas A. niveus produced more xylanase on birchwood xylan. The optimum temperature of the xylanases from A. fumigatus and A. niveus was around 60-70A degrees C. The enzymes were stable for 30 min at 60A degrees C, maintaining 95-98% of the initial activity. After 1 h at this temperature, the xylanase from A. niveus still retained 85% of initial activity, while the xylanase from A. fumigatus was only 40% active. The pH optimum of the xylanases was acidic (4.5-5.5). The pH stability for the xylanase from A. fumigatus was higher at pH 6.0-8.0, while the enzyme from A. niveus was more stable at pH 4.5-6.5. Crude enzymatic extracts were used to clarify cellulose pulp and the best result was obtained with the A. niveus preparation, showing kappa efficiency around 39.6% as compared to only 11.7% for that of A. fumigatus.

Basic density and pulp yield relationship with some chemical parameters in eucalyptus trees

The objective of this work was to evaluate the use of basic density and pulp yield correlations with some chemical parameters, in order to differentiate an homogeneous eucalyptus tree population, in terms of its potential for pulp production or some other technological applications. Basic density and kraft pulp yield were determined for 120 Eucalyptus globulus trees, and the values were plotted as frequency distributions. Homogenized samples from the first and fourth density quartiles and first and fourth yield quartiles were submitted to total phenols, total sugars and methoxyl group analysis. Syringyl/guaiacyl (S/G) and syringaldehyde/vanillin (S/V) ratios were determined on the kraft lignins from wood of the same quartiles. The results show the similarity between samples from high density and low yield quartiles, both with lower S/G (3.88-4.12) and S/V (3.99-4.09) ratios and higher total phenols (13.3-14.3 g gallic acid kg-1 ). Woods from the high yield quartile are statistically distinguished from all the others because of their higher S/G (5.15) and S/V (4.98) ratios and lower total phenols (8.7 g gallic acid kg-1 ). Methoxyl group and total sugars parameters are more adequate to distinguish wood samples with lower density.

Cost efficient extractive removal of birch pulp

Tämän diplomityön tarkoituksena oli selvittää kustannustehokkaita keinoja uuteaineiden vähentämiseksi koivusulfaattimassasta. Uuteaineet voivat aiheuttaa ongelmia muodostaessaan saostumia prosessilaitteisiin. Saostumat aiheuttavat tukkeumia ja mittaushäiriöitä, mutta irrotessaan ne myös huonontavat sellun laatua. Lopputuotteeseen joutuessaan ne voivat lisäksi aiheuttaa haju- ja makuhaittoja, joilla on erityistä merkitystä esimerkiksi valmistettaessa elintarvikekartonkeja. Tämä työ tehtiin Stora Enson sellutehtaalla, Enocell Oy:llä, Uimaharjussa. Teoriaosassa käsiteltiin uuteaineiden koostumusta ja niiden aiheuttamia ongelmia sellu– ja paperitehtaissa. Lisäksi koottiin aikaisempien tehdaskokeiden fysikaalisia ja kemiallisia keinoja vähentää koivu-uutetta. Tarkastelualueina olivat puunkäsittely, keitto, pesemö ja valkaisu. Kokeellisessa osassa suoritettiin esikokeita laboratorio- ja tehdasmittakaavassa, jotta saavutettaisiin käytännöllistä tietoa itse lopuksi tehtävää tehdasmittakaavan koetta varten. Laboratoriokokeissa tutkittiin mm. keiton kappaluvun, lisäaineiden ja hartsisaippuan vaikutusta koivu-uutteeseen. Lisäksi suoritettiin myös happo- (A) ja peretikkahappovaiheen (Paa) laboratoriokokeet. Tehdasmittakaavassa tarkasteltiin mm. keiton kappaluvun, pesemön lämpötilan, A-vaiheen, valkaisun peroksidi- ja Paa-vaiheen vaikutusta koivu-uutteeseen. Uutteenpoistotehokkuutta eri menetelmien välillä vertailtiin niin määrällisesti kuin rahallisesti. Uutteenpoistotehokkuudella mitattuna vertailuvaihe oli tehokkain pesemön loppuvaiheessa ja valkaisun alkuvaiheessa. Pesemön loppuvaiheessa uutteenpoistoreduktiot olivat noin 30 % ja valkaisun alkuvaiheessa 40 %. Peroksidivaihe oli tehokkain käytettynä valkaisun loppuvaiheessa noin 40 % reduktiolla. Kustannustehokkuudella mitattuna tehokkaimmaksi osoittautui A-vaihe yhdessä peroksidivaiheen kanssa. Säästöt vertailujaksoon verrattuna olivat noin 0.3 €/ADt. Lisäksi kyseinen yhdistelmä osoittautui hyväksi keinoksi säilyttää uutetaso alle maksimirajan kuitulinja 2:lla, kun kuitulinjalla 1 tuotettiin samanaikaisesti armeeraussellua.

Measurement Problems and Problem-Solving in Kraft Pulping

Tämän työn tarkoituksena on koota yhteen selluprosessin mittausongelmat ja mahdolliset mittaustekniikat ongelmien ratkaisemiseksi. Pääpaino on online-mittaustekniikoissa. Työ koostuu kolmesta osasta. Ensimmäinen osa on kirjallisuustyö, jossa esitellään nykyaikaisen selluprosessin perusmittaukset ja säätötarpeet. Mukana on koko kuitulinja puunkäsittelystä valkaisuun ja kemikaalikierto: haihduttamo, soodakattila, kaustistamo ja meesauuni. Toisessa osassa mittausongelmat ja mahdolliset mittaustekniikat on koottu yhteen ”tiekartaksi”. Tiedot on koottu vierailemalla kolmella suomalaisella sellutehtaalla ja haastattelemalla laitetekniikka- ja mittaustekniikka-asiantuntijoita. Prosessikemian paremmalle ymmärtämiselle näyttää haastattelun perusteella olevan tarvetta, minkä vuoksi konsentraatiomittaukset on valittu jatkotutkimuskohteeksi. Viimeisessä osassa esitellään mahdollisia mittaustekniikoita konsentraatiomittausten ratkaisemiseksi. Valitut tekniikat ovat lähi-infrapunatekniikka (NIR), fourier-muunnosinfrapunatekniikka (FTIR), online-kapillaarielektroforeesi (CE) ja laserindusoitu plasmaemissiospektroskopia (LIPS). Kaikkia tekniikoita voi käyttää online-kytkettyinä prosessikehitystyökaluina. Kehityskustannukset on arvioitu säätöön kytketylle online-laitteelle. Kehityskustannukset vaihtelevat nollasta miestyövuodesta FTIR-tekniikalle viiteen miestyövuoteen CE-laitteelle; kehityskustannukset riippuvat tekniikan kehitysasteesta ja valmiusasteesta tietyn ongelman ratkaisuun. Työn viimeisessä osassa arvioidaan myös yhden mittausongelman – pesuhäviömittauksen – ratkaisemisen teknis-taloudellista kannattavuutta. Ligniinipitoisuus kuvaisi nykyisiä mittauksia paremmin todellista pesuhäviötä. Nykyään mitataan joko natrium- tai COD-pesuhäviötä. Ligniinipitoisuutta voidaan mitata UV-absorptiotekniikalla. Myös CE-laitetta voitaisiin käyttää pesuhäviön mittauksessa ainakin prosessikehitysvaiheessa. Taloudellinen tarkastelu pohjautuu moniin yksinkertaistuksiin ja se ei sovellu suoraan investointipäätösten tueksi. Parempi mittaus- ja säätöjärjestelmä voisi vakauttaa pesemön ajoa. Investointi ajoa vakauttavaan järjestelmään on kannattavaa, jos todellinen ajotilanne on tarpeeksi kaukana kustannusminimistä tai jos pesurin ajo heilahtelee eli pesuhäviön keskihajonta on suuri. 50 000 € maksavalle mittaus- ja säätöjärjestelmälle saadaan alle 0,5 vuoden takaisinmaksuaika epävakaassa ajossa, jos COD-pesuhäviön vaihteluväli on 5,2 – 11,6 kg/odt asetusarvon ollessa 8,4 kg/odt. Laimennuskerroin vaihtelee tällöin välillä 1,7 – 3,6 m3/odt asetusarvon ollessa 2,5 m3/odt.

Integration of a Bioethanol Process to a Pulp Mill

Tässä diplomityössä tutkittiin puuhakkeen esihydrolyysi- ja hakkuujätteen hydrolyysiprosessien integroimista sellutehtaaseen bioetanolin tuottamiseksi. Tällaisesta ns. biojalostamosta luotiin WinGEMS-simulointiohjelmalla simulointimalli, jonka avulla tutkittiin bioetanoliprosessin vaikutusta sellutehtaan massa- ja energiataseisiin sekä alustavaa biojalostamon kannattavuutta. Simuloinnissa tarkasteltiin kolmea eri tapausta, joissa mäntysellun tuotannon ajateltiin olevan 1000 tonnia päivässä ja hakkuujätettä käytettävän 10 % tarvittavan kuitupuun määrästä: 1) Puuhakkeen esihydrolyysi ja hakkuujätteen hydrolyysi etanolin tuottamiseksi 2) Puuhakkeen esihydrolyysi, hakkuujäte kuorikattilaan poltettavaksi 3) Ei esihydrolyysiä, hakkuujäte kuorikattilaan poltettavaksi Verrattuna tapaukseen 3, puun kulutus kasvaa 16 % esihydrolysoitaessa puuhake ennen keittoa tapauksissa 1 ja 2. Kasvaneella puun kulutuksella tuotetaan tapauksessa 1 149 tonnia etanolia ja 240 MWh enemmän ylimääräsähköä päivässä. Tapauksessa 2 tuotetaan 68 tonnia etanolia ja 460 MWh enemmän ylimääräsähköä päivässä. Tämä tuottaisi vuotuista lisäkassavirtaa 18,8 miljoonaa euroa tapauksessa 1 ja 9,4 miljoonaa euroa tapauksessa 2. Hydrolyysin tuoteliuoksen, hydrolysaatin, haihduttaminen sekä hydrolyysiprosessien orgaanisten jäännöstuotteiden haihduttaminen ja polttaminen kasvattavat haihduttamon ja soodakattilan kuormitusta. Verrattuna tapaukseen 3, tapauksissa 1 ja 2 haihduttamon vaiheiden määrä on kasvatettava viidestä seitsemään ja tarvittavat lämmönsiirtopinta-alat lähes kaksinkertaistettava. Soodakattilan kuormitus kasvaa 39 % tapauksessa 1 ja 26 % tapauksessa 2.

Research on the suitability of organosolv semi-chemical triticale fibers as reinforcement for recycled hdpe composites

The main objective of this research was to study the feasibility of incorporating organosolv semi-chemical triticale fibers as the reinforcing element in recycled high density polyethylene (HDPE). In the first step, triticale fibers were characterized in terms of chemical composition and compared with other biomass species (wheat, rye, softwood, and hardwood). Then, organosolv semi-chemical triticale fibers were prepared by the ethanolamine process. These fibers were characterized in terms of its yield, kappa number, fiber length/diameter ratio, fines, and viscosity; the obtained results were compared with those of eucalypt kraft pulp. In the second step, the prepared fibers were examined as a reinforcing element for recycled HDPE composites. Coupled and non-coupled HDPE composites were prepared and tested for tensile properties. Results showed that with the addition of the coupling agent maleated polyethylene (MAPE), the tensile properties of composites were significantly improved, as compared to non-coupled samples and the plain matrix. Furthermore, the influence of MAPE on the interfacial shear strength (IFSS) was studied. The contributions of both fibers and matrix to the composite strength were also studied. This was possible by the use of a numerical iterative method based on the Bowyer-Bader and Kelly-Tyson equations

The Impact of Aspen and Alder on the Quality of NHBK

The purpose of this work was to study the effect of aspen and alder on birch cooking and the quality of the pulp produced. Three different birch kraft pulps were studied. As a reference, pure aspen and alder were included. The laboratory trials were done at the UPM Research Centre in Lappeenranta, Finland. The materials used were birch, aspen and alder mill chips that were collected around the area of South-Carelia in Finland. The chips used in the study were pulped using a standard kraft process. The pulps including birch fibres were ECF-bleached at laboratory scale to a target brightness of 85 %. The bleached pulps were beaten at low consistency by a laboratory Voith Sulzer refiner and tested for optical and physical properties. The theoretical part is a study of hardwoods that takes into accounts the differences between birch, aspen and alder. Major sub-areas were fibre and paper-technical properties as well as chemical composition and their influence on the different properties. The pulp properties of birch, aspen and alder found in previous studies were reported. Russian hardwood forest resources were also investigated. The fundamentals of kraft pulping and bleaching were studied at the end of theoretical part. The major effect of replacing birch with aspen and alder was the deterioration (lowering) of tensile and tear strengths. In other words, addition of aspen and alder to a birch furnish reduced strength properties. The reinforcement ability of the tested pulps was the following: 100 % birch > 80 % birch, 20 % aspen > 70 % birch, 20 % aspen, 10 % alder. The second thing noted was that blending of birch together with aspen and alder give better smoothness, optical properties and also formation. It can be concluded, that replacement of birch with alder during cooking by more than 10 % can negatively affect on the paper-technical properties of birch pulp. Mixing pure birch and aspen pulps would be more beneficial when producing printing paper made from chemical pulp.

Branqueamento de polpa celulósica kraft de eucalipto com peróxido ácido ativado por molibdênio

Optimum conditions to run the P Mo stage for bleaching eucalyptus kraft pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H2O2. The P Mo stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 ºC), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P Mo stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO.

On the potential utilisation of sawdust and wood chip screenings

This work is based on the utilisation of sawdust and wood chip screenings for different purposes. A substantial amount of these byproducts are readily available in the Finnish forest industry. A black liquor impregnation study showed that sawdust-like wood material behaves differently from normal chips. Furthermore, the fractionation and removal of the smallest size fractions did not have a significant effect on the impregnation of sawdust-like wood material. Sawdust kraft cooking equipped with an impregnation stage increases the cooking yield and decreases the lignin content of the produced pulp. Impregnation also increases viscosity of the pulp and decreases chlorine dioxide consumption in bleaching. In addition, impregnation increases certain pulp properties after refining. Hydrotropic extraction showed that more lignin can be extracted from hardwood than softwood. However, the particle size had a major influence on the lignin extraction. It was possible to extract more lignin from spruce sawdust than spruce chips. Wood chip screenings are usually combusted to generate energy. They can also be used in the production of kraft pulp, ethanol and chemicals. It is not economical to produce ethanol from wood chip screenings because of the expensive wood material. Instead, they should be used for production of steam and energy, kraft pulp and higher value added chemicals. Bleached sawdust kraft pulp can be used to replace softwood kraft pulp in mechanical pulp based papers because it can improve certain physical properties. It is economically more feasible to use bleached sawdust kraft pulp in stead of softwood kraft pulp, especially when the reinforcement power requirement is moderate.

Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill

Tension (TW) and opposite wood (OW) of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively). The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes) were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EO)D1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.

Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Separation of lignin in Pulp Mill process and its effect on sodium sulphur balance

The aim of this thesis is to define effects of lignin separation process on Pulp mill chemical balance especially on sodium/sulphur-balance. The objective is to develop a simulation model with WinGEMS Process Simulator and use that model to simulate the chemical balances and process changes. The literature part explains what lignin is and how kraft pulp is produced. It also introduces to the methods that can be used to extract lignin from black liquor stream and how those methods affect the pulping process. In experimental part seven different cases are simulated with the created simulation model. The simulations are based on selected reference mill that produces 500 000 tons of bleached air-dried (90 %) pulp per year. The simulations include the chemical balance calculation and the estimated production increase. Based on the simulations the heat load of the recovery boiler can be reduced and the pulp production increased when lignin is extracted. The simulations showed that decreasing the waste acid stream intake from the chlorine dioxide plant is an effective method to control the sulphidity level when about 10 % of lignin is extracted. With higher lignin removal rates the in-mill sulphuric acid production has been discovered to be a better alternative to the sulphidity control.