Noise and PSRR improvement technique for TPC readout front-end in CMOS. technology.

ALICE is one of four major experiments of particle accelerator LHC installed in the European laboratory CERN. The management committee of the LHC accelerator has just approved a program update for this experiment. Among the upgrades planned for the coming years of the ALICE experiment is to improve the resolution and tracking efficiency maintaining the excellent particles identification ability, and to increase the read-out event rate to 100 KHz. In order to achieve this, it is necessary to update the Time Projection Chamber detector (TPC) and Muon tracking (MCH) detector modifying the read-out electronics, which is not suitable for this migration. To overcome this limitation the design, fabrication and experimental test of new ASIC named SAMPA has been proposed . This ASIC will support both positive and negative polarities, with 32 channels per chip and continuous data readout with smaller power consumption than the previous versions. This work aims to design, fabrication and experimental test of a readout front-end in 130nm CMOS technology with configurable polarity (positive/negative), peaking time and sensitivity. The new SAMPA ASIC can be used in both chambers (TPC and MCH). The proposed front-end is composed of a Charge Sensitive Amplifier (CSA) and a Semi-Gaussian shaper. In order to obtain an ASIC integrating 32 channels per chip, the design of the proposed front-end requires small area and low power consumption, but at the same time requires low noise. In this sense, a new Noise and PSRR (Power Supply Rejection Ratio) improvement technique for the CSA design without power and area impact is proposed in this work. The analysis and equations of the proposed circuit are presented which were verified by electrical simulations and experimental test of a produced chip with 5 channels of the designed front-end. The measured equivalent noise charge was <550e for 30mV/fC of sensitivity at a input capacitance of 18.5pF. The total core area of the front-end was 2300?m × 150?m, and the measured total power consumption was 9.1mW per channel.

DESIGN OF A MINIATURIZED SOP INTEGRATED GNSS RF FRONT-END MODULE

Navigation devices used to be bulky and expensive and were not widely commercialized for personal use. Nowadays, all useful electronic devices are turning into being handheld so that they can be conveniently used anytime and anywhere. One can claim that almost any mobile phone, used today, has quite strong navigational capabilities that can efficiently work anywhere in the globe. No matter where you are, you can easily know your exact location and make your way smoothly to wherever you would like to go. This couldn’t have been made possible without the existence of efficient and small microwave circuits responsible for the transmission and reception of high quality navigation signals. This thesis is mainly concerned with the design of novel highly miniaturized and efficient filtering components working in the Global Navigational Satellite Systems (GNSS) frequency band to be integrated within an efficient Radio Frequency (RF) front-end module (FEM). A System-on-Package (SoP) integration technique is adopted for the design of all the components in this thesis. Two novel miniaturized filters are designed, where one of them is a wideband filter targeting the complete GNSS band with a fractional bandwidth of almost 50% at a center frequency of 1.385 GHz. This filter utilizes a direct inductive coupling topology to achieve the required wide band performance. It also has very good out-of-band rejection and low IL. Whereas the other dual band filter will only cover the lower and upper GNSS bands with a rejection notch in between the two bands. It has very good inter band rejection. The well-known “divide and conquer” design methodology was applied for the design of this filter to help save valuable design and optimization time. Moreover, the performance of two commercially available ultra-Low Noise Amplifiers (LNAs) is studied. The complete RF FEM showed promising preliminary performance in terms of noise figure, gain and bandwidth, where it out performed other commercial front-ends in these three aspects. All the designed circuits are fabricated and tested. The measured results are found to be in good agreements with the simulations.

Using front-end and formative evaluation to design and test persuasive bird feeding warning signs

Wildlife feeding is a wide-spread and controversial practice that can pose serious threats to the safety of both wildlife and visitors. The design and effectiveness of warning signs in recreational areas varies considerably and is rarely the product of theoretical models or scientific research. This study uses front-end and formative evaluation to design and test the perceived effectiveness of warning signs relating to bird feeding. Stage One examined visitors' beliefs, attitudes and bird feeding behaviour and found significant differences between feeders and non-feeders. Stage Two involved designing and evaluating three signs that built on the beliefs, knowledge and mis/conceptions identified in Stage One. Respondents thought the sign that focused on the birds' health and safety would be the most persuasive, however, elements of the other two signs were also positively evaluated. The article concludes with recommendations for the wording of future bird feeding warning signs. (c) 2004 Elsevier Ltd. All rights reserved.

The development of a new compiler-compiler front-end

The increasing cost of developing complex software systems has created a need for tools which aid software construction. One area in which significant progress has been made is with the so-called Compiler Writing Tools (CWTs); these aim at automated generation of various components of a compiler and hence at expediting the construction of complete programming language translators. A number of CWTs are already in quite general use, but investigation reveals significant drawbacks with current CWTs, such as lex and yacc. The effective use of a CWT typically requires a detailed technical understanding of its operation and involves tedious and error-prone input preparation. Moreover, CWTs such as lex and yacc address only a limited aspect of the compilation process; for example, actions necessary to perform lexical symbol valuation and abstract syntax tree construction must be explicitly coded by the user. This thesis presents a new CWT called CORGI (COmpiler-compiler from Reference Grammar Input) which deals with the entire `front-end' component of a compiler; this includes the provision of necessary data structures and routines to manipulate them, both generated from a single input specification. Compared with earlier CWTs, CORGI has a higher-level and hence more convenient user interface, operating on a specification derived directly from a `reference manual' grammar for the source language. Rather than developing a compiler-compiler from first principles, CORGI has been implemented by building a further shell around two existing compiler construction tools, namely lex and yacc. CORGI has been demonstrated to perform efficiently in realistic tests, both in terms of speed and the effectiveness of its user interface and error-recovery mechanisms.

The implementation of a functional query language front-end to a relational database system. Available in 2 volumes.

Database systems have a user interface one of the components of which will normally be a query language which is based on a particular data model. Typically data models provide primitives to define, manipulate and query databases. Often these primitives are designed to form self-contained query languages. This thesis describes a prototype implementation of a system which allows users to specify queries against the database in a query language whose primitives are not those provided by the actual model on which the database system is based, but those provided by a different data model. The implementation chosen is the Functional Query Language Front End (FQLFE). This uses the Daplex functional data model and query language. Using FQLFE, users can specify the underlying database (based on the relational model) in terms of Daplex. Queries against this specified view can then be made in Daplex. FQLFE transforms these queries into the query language (Quel) of the underlying target database system (Ingres). The automation of part of the Daplex function definition phase is also described and its implementation discussed.

Especificações e concepções de front-end UHF integrado e multipadrão em tecnologia CMOS 130nm

The Brazilian Environmental Data Collecting System (SBCDA) collects and broadcasts meteorological and environmental data, to be handled by dozens of institutions and organizations. The system space segment, composed by the data collecting satellites, plays an important role for the system operation. To ensure the continuity and quality of these services, efforts are being made to the development of new satellite architectures. Aiming a reduction of size and power consumption, the design of an integrated circuit containing a receiver front-end is proposed, to be embedded in the next SBCDA satellite generations. The circuit will also operate under the requirements of the international data collecting standard ARGOS. This work focuses on the design of an UHF low noise amplifier and mixers in a CMOS standard technology. The specifi- cations are firstly described and the circuit topologies presented. Then the circuit conception is discussed and the design variables derived. Finally, the layout is designed and the final results are commented. The chip will be fabricated in a 130 nm technology from ST Microelectronics.

DESIGN OF A MINIATURIZED SOP INTEGRATED GNSS RF FRONT-END MODULE

Navigation devices used to be bulky and expensive and were not widely commercialized for personal use. Nowadays, all useful electronic devices are turning into being handheld so that they can be conveniently used anytime and anywhere. One can claim that almost any mobile phone, used today, has quite strong navigational capabilities that can efficiently work anywhere in the globe. No matter where you are, you can easily know your exact location and make your way smoothly to wherever you would like to go. This couldn’t have been made possible without the existence of efficient and small microwave circuits responsible for the transmission and reception of high quality navigation signals. This thesis is mainly concerned with the design of novel highly miniaturized and efficient filtering components working in the Global Navigational Satellite Systems (GNSS) frequency band to be integrated within an efficient Radio Frequency (RF) front-end module (FEM). A System-on-Package (SoP) integration technique is adopted for the design of all the components in this thesis. Two novel miniaturized filters are designed, where one of them is a wideband filter targeting the complete GNSS band with a fractional bandwidth of almost 50% at a center frequency of 1.385 GHz. This filter utilizes a direct inductive coupling topology to achieve the required wide band performance. It also has very good out-of-band rejection and low IL. Whereas the other dual band filter will only cover the lower and upper GNSS bands with a rejection notch in between the two bands. It has very good inter band rejection. The well-known “divide and conquer” design methodology was applied for the design of this filter to help save valuable design and optimization time. Moreover, the performance of two commercially available ultra-Low Noise Amplifiers (LNAs) is studied. The complete RF FEM showed promising preliminary performance in terms of noise figure, gain and bandwidth, where it out performed other commercial front-ends in these three aspects. All the designed circuits are fabricated and tested. The measured results are found to be in good agreements with the simulations.

Análisis y simulación de un rectificador trifásico controlado Active Front End (AFE)

Este artículo presenta un resultado de investigación financiado con recursos propios en el que se expone un modelo en espacio de estados de un rectificador trifásico controlado active front end. Utilizando este modelo se deriva una ley de control orientado al voltaje (VOC), enfocado en el comportamiento como carga resistiva, factor de potencia unitario, el cual es probado mediante simulación usando el Toolbox SimPowerSystem en Simulink de Matlab®.

Front end development for building automation systems using JavaScript Frameworks

Automation technologies are widely acclaimed to have the potential to significantly reduce energy consumption and energy-related costs in buildings. However, despite the abundance of commercially available technologies, automation in domestic environments keep on meeting commercial failures. The main reason for this is the development process that is used to build the automation applications, which tend to focus more on technical aspects rather than on the needs and limitations of the users. An instance of this problem is the complex and poorly designed home automation front-ends that deter customers from investing in a home automation product. On the other hand, developing a usable and interactive interface is a complicated task for developers due to the multidisciplinary challenges that need to be identified and solved. In this context, the current research work investigates the different design problems associated with developing a home automation interface as well as the existing design solutions that are applied to these problems. The Qualitative Data Analysis approach was used for collecting data from research papers and the open coding process was used to cluster the findings. From the analysis of the data collected, requirements for designing the interface were derived. A home energy management functionality for a Web-based home automation front-end was developed as a proof-of-concept and a user evaluation was used to assess the usability of the interface. The results of the evaluation showed that this holistic approach to designing interfaces improved its usability which increases the chances of its commercial success.

Progettazione ed Implementazione Front-End di un Sistema Integrato di Customer Assistance in ambito Industry 4.0

Al giorno d'oggi, l'industry 4.0 è un movimento sempre più prominente che induce ad equipaggiare gli impianti industriali con avanzate infrastrutture tecnologiche digitali, le quali operano sinergicamente con l'impianto, al fine di controllare ed aumentare la produttività, monitorare e prevenire i futuri guasti, ed altro ancora. In questo ambito, gli utenti sono parte integrante della struttura produttiva, in cui ricoprono ruoli strategici e flessibili, collaborano fra loro e con le macchine, con l’obiettivo di affrontare e risolvere proattivamente una vasta gamma di problemi complessi. In particolare, la customer assistance nel settore industriale può certamente variare in relazione a molteplici elementi: il tipo di produzione e le caratteristiche del prodotto; l'organizzazione ed infrastruttura aziendale interna; la quantità di risorse disponibili che possono essere impiegate; il grado di importanza ricoperto dalla customer assistance nel settore industriale di riferimento; altri eventuali fattori appartenenti ad un dominio specifico. Per queste ragioni, si è cercato di individuare e categorizzare nel modo più accurato possibile, il lavoro svolto in questo elaborato ed il contesto nel quale è stato sviluppato. In questa tesi, viene descritta un'applicazione web per erogare assistenza al cliente in ambito di industria 4.0, attraverso il paradigma di ticketing o ticket di supporto/assistenza. Questa applicazione è integrata nel sistema Mentor, il quale è attivo già da anni nel settore industriale 4.0. Il progetto Mentor è una suite di applicazioni cloud-based creata dal gruppo Bucci Industries, una multinazionale attiva nell'industria e nell'automazione con sede a Faenza. In questo caso di studio, si presenta la progettazione ed implementazione della parte front-end del suddetto sistema di assistenza, il quale è integrato ed interconnesso con un paio di applicazioni tipiche di industria 4.0, presenti nella stessa suite di applicazioni.

Design of a LNA and a Gilbert Cell Mixer MMICs with a GaAsPHEMT technology

The design of a Gilbert Cell Mixer and a low noise amplifier (LNA), using GaAs PHEMT technology is presented. The compatibility is shown for co-integration of both block on the same chip, to form a high performance 1.9 GHz receiver front end. The designed LNA shows 9.23 dB gain and 2.01 dB noise figure (NF). The mixer is designed to operate at RF=1.9 GHz, LO=2.0 GHz and IF=100 MHz with a gain of 14.3 dB and single sideband noise figure (SSB NF) of 9.6 dB. The mixer presents a bandwith of 8 GHz.

Design of a LNA and a Gilbert Cell Mixer MMICs with a GaAs PHEMT technology

The design of a Gilbert Cell Mixer and a low noise amplifier (LNA), using GaAs PHEMT technology is presented. The compatibility is shown for co-integration of both block on the same chip, to form a high performance 1.9 GHz receiver front-end. The designed LNA shows 9.23 dB gain and 2.01 dB noise figure (NF). The mixer is designed to operate at RF=1.9 GHz, LO=2.0 GHz and IF=100 MHz with a gain of 14.3 dB and single sideband noise figure (SSB NF) of 9.6 dB. The mixer presents a bandwith of 8 GHz.

Joint array combining and MLSE for single-user receivers in multipath Gaussian multiuser channels

The well-known structure of an array combiner along with a maximum likelihood sequence estimator (MLSE) receiveris the basis for the derivation of a space-time processor presentinggood properties in terms of co-channel and intersymbol interferencerejection. The use of spatial diversity at the receiver front-endtogether with a scalar MLSE implies a joint design of the spatialcombiner and the impulse response for the sequence detector. Thisis faced using the MMSE criterion under the constraint that thedesired user signal power is not cancelled, yielding an impulse responsefor the sequence detector that is matched to the channel andcombiner response. The procedure maximizes the signal-to-noiseratio at the input of the detector and exhibits excellent performancein realistic multipath channels.

ENCORE: Enhanced Galileo code receiver for surveying applications

In this paper we describe the development of a low-cost high-accuracy Galileo Code receiver, user application software and positioning algorithms for land management applications, which have been implemented using a dedicated FPGA board and dual frequency Galileo E5/L1 Radio Frequency Front-End. The current situation of rural property surveying in Brazil is described and the use of code measurements from the new Galileo signals E5 AltBOC combined with E1 MBOC for use in land management applications is explored. We explain how such approach is expected to allow delivering an absolute positioning solution which could bridge the gap between receivers of high cost/complexity/accuracy based on carrier phase and receivers of lower cost/accuracy based on pseudorange observables. The system is presented together with a detailed description of main components: the Code Receiver and the Application Software. The work presented is part of an ongoing European-Brazilian consortium effort to explore the use of new Galileo for land management applications in Brazil and sponsored by the GNSS Supervisory Authority (GSA).