Thermal-Hydraulic Studies on the Safety Of VVER-440 Type Nuclear Power Plants

This thesis includes several thermal hydraulic analyses related to the Loviisa WER 440 nuclear power plant units. The work consists of experimental studies, analysis of the experiments, analysis of some plant transits and development of a calculational model for calculation of boric acid concentrations in the reactor. In the first part of the thesis, in the case of won of boric acid solution behaviour during long term cooling period of LOCAs, experiments were performed in scaled down test facilities. The experimental data together with the results of RELAPS/MOD3 simulations were used to develop a model for calculations of boric acid concentrations in the reactor during LOCAs. The results of calculations showed that margins to critical concentrations that would lead to boric acid crystallization were large, both in the reactor core and in the lower plenum. This was mainly caused by the fact that water in the primary cooling circuit includes borax (Na)BsO,.IOHZO), which enters the reactor when ECC water is taken from the sump and greatly increases boric acid solubility in water. In the second part, in the case of simulation of horizontal steam generators, experiments were performed with PACTEL integral test loop to simulate loss of feedwater transients. The PACTEL experiments, as well as earlier REWET III natural circulation tests, were analyzed with RELAPS/MOD3 Version Sm5 code. The analysis showed that the code was capable of simulating the main events during the experiments. However, in the case of loss of secondary side feedwater the code was not completely capable to simulate steam superheating in the secondary side of the steam generators. The third part of the work consists of simulations of Loviisa VVER reactor pump trip transients with RELAPSlMODI Eur, RELAPS/MOD3 and CATHARE codes. All three codes were capable to simulate the two selected pump trip transients and no significant differences were found between the results of different codes. Comparison of the calculated results with the data measured in the Loviisa plant also showed good agreement.

The maximum voltage drop in an on-chip power distribution network: analysis of square, triangular and hexagonal power pad arrangements

A mathematical model of the voltage drop which arises in on-chip power distribution networks is used to compare the maximum voltage drop in the case of different geometric arrangements of the pads supplying power to the chip. These include the square or Manhattan power pad arrangement, which currently predominates, as well as equilateral triangular and hexagonal arrangements. In agreement with the findings in the literature and with physical and SPICE models, the equilateral triangular power pad arrangement is found to minimize the maximum voltage drop. This headline finding is a consequence of relatively simple formulas for the voltage drop, with explicit error bounds, which are established using complex analysis techniques, and elliptic functions in particular.

Distributed ControlArchitecture of Power Electronics Building-Block-Based Frequency Converters

The increasing power demand and emerging applications drive the design of electrical power converters into modularization. Despite the wide use of modularized power stage structures, the control schemes that are used are often traditional, in other words, centralized. The flexibility and re-usability of these controllers are typically poor. With a dedicated distributed control scheme, the flexibility and re-usability of the system parts, building blocks, can be increased. Only a few distributed control schemes have been introduced for this purpose, but their breakthrough has not yet taken place. A demand for the further development offlexible control schemes for building-block-based applications clearly exists. The control topology, communication, synchronization, and functionality allocationaspects of building-block-based converters are studied in this doctoral thesis. A distributed control scheme that can be easily adapted to building-block-based power converter designs is developed. The example applications are a parallel and series connection of building blocks. The building block that is used in the implementations of both the applications is a commercial off-the-shelf two-level three-phase frequency converter with a custom-designed controller card. The major challenge with the parallel connection of power stages is the synchronization of the building blocks. The effect of synchronization accuracy on the system performance is studied. The functionality allocation and control scheme design are challenging in the seriesconnected multilevel converters, mainly because of the large number of modules. Various multilevel modulation schemes are analyzed with respect to the implementation, and this information is used to develop a flexible control scheme for modular multilevel inverters.

Flexible multibody approach in bone strain estimation during physical activity:

Bone strain plays a major role as the activation signal for the bone (re)modeling process, which is vital for keeping bones healthy. Maintaining high bone mineral density reduces the chances of fracture in the event of an accident. Numerous studies have shown that bones can be strengthened with physical exercise. Several hypotheses have asserted that a stronger osteogenic (bone producing) effect results from dynamic exercise than from static exercise. These previous studies are based on short-term empirical research, which provide the motivation for justifying the experimental results with a solid mathematical background. The computer simulation techniques utilized in this work allow for non-invasive bone strain estimation during physical activity at any bone site within the human skeleton. All models presented in the study are threedimensional and actuated by muscle models to replicate the real conditions accurately. The objective of this work is to determine and present loading-induced bone strain values resulting from physical activity. It includes a comparison of strain resulting from four different gym exercises (knee flexion, knee extension, leg press, and squat) and walking, with the results reported for walking and jogging obtained from in-vivo measurements described in the literature. The objective is realized primarily by carrying out flexible multibody dynamics computer simulations. The dissertation combines the knowledge of finite element analysis and multibody simulations with experimental data and information available from medical field literature. Measured subject-specific motion data was coupled with forward dynamics simulation to provide natural skeletal movement. Bone geometries were defined using a reverse engineering approach based on medical imaging techniques. Both computed tomography and magnetic resonance imaging were utilized to explore modeling differences. The predicted tibia bone strains during walking show good agreement with invivo studies found in the literature. Strain measurements were not available for gym exercises; therefore, the strain results could not be validated. However, the values seem reasonable when compared to available walking and running invivo strain measurements. The results can be used for exercise equipment design aimed at strengthening the bones as well as the muscles during workout. Clinical applications in post fracture recovery exercising programs could also be the target. In addition, the methodology introduced in this study, can be applied to investigate the effect of weightlessness on astronauts, who often suffer bone loss after long time spent in the outer space.

Keskusteluja vuokratyöstä. Vuokratyön diskursiivinen rakentuminen Suomessa

1990-luvun alussa lainsäädäntö ja työmarkkinajärjestöt määrittelivät Suomessa, että vuokratyötä tuli käyttää vain tilapäiseen työvoimatarpeeseen, esimerkiksi sijaisuuksiin ja ruuhkahuippuihin. Joillakin aloilla vuokratyö oli työnantajien ja työntekijöiden yhteissopimuksella kielletty. Vaikka vuokratyösuhteet saivat jo 1980-luvulla niin Suomessa kuin kansainvälisestikin maineen työsuhdekeinotteluna, alkoi vuokratyön määrä Suomessa kasvaa 1990-luvun puolivälissä ja erityisesti tultaessa 2000-luvulle. Suomalaiset akateemiset tutkijat eivät ole juuri vuokratyöstä kiinnostuneet. Aiemmat, harvalukuiset tutkimukset ovat keskittyneet lähinnä työyhteisöjen ja työntekijöiden kokemuksiin sekä vuokratyön työehtoihin. Vuokratyö ymmärretäänkin edelleen lähinnä työntekijän subjektiivisena kokemuksena. Vuokratyössä on kuitenkin kysymys paitsi kokemuksista, myös yhteiskunnallisesta valtakamppailusta, jossa diskursiivisin keinoin pyritään vaikuttamaan ilmiöön nimeltä vuokratyö, laajemmin ilmiöön nimeltä työmarkkinat, sekä toisaalta kansalaisten käsityksiin työelämän ”normaalista”. Käsillä oleva tutkimus laajentaa ymmärrystä vuokratyöstä tarkastelemalla ilmiötä lainsäädännön, uutisoinnin ja markkinoinnin rakentamien julkisten käsitysten ja merkityksenantojen kautta. Teoreettisena viitekehyksenä käytän hallinnan ja työprosessin säätelyn teoriaperinteitä. Se, miten työmarkkinoiden muutosta ja uusia työsuhdemuotoja politiikassa, mediassa, lainsäädännössä, tai työpaikan kahvipöytäkeskusteluissa perustellaan ja tehdään ymmärrettäväksi, on samalla työelämään kiinnitettävien arvojen, merkitysten ja toimijuuksien luomista, rajaamista ja kuvailua. Työelämäpuheessa ei siis ole kyse vain talouden lainalaisuuksista, kansantalouden toimivuudesta, tai yritysten kilpailukyvystä, vaan myös ja erityisesti niiden toimijoiden luomisesta, määrittelemisestä ja legitimoimisesta, jotka työelämän kentällä saavat toimia ja tulevat palkituiksi. Säätelyn ja hallinnan näkökulmasta on relevanttia tarkastella millaisilla käsitteillä ja merkityksillä vuokratyötä ilmiönä rakennetaan . Tutkimuskysymyksinä esitän: 1) Miten ja millä perusteilla vuokratyöstä rakennettiin Suomessa legitiimi tapa työllistää ja työllistyä? 2) Millaisia työntekijäideaaleja vuokratyöhön liittyvissä keskusteluissa rakennetaan? Tutkimusaineistona tarkastelen lainsäädäntöön liittyviä dokumentteja, Helsingin Sanomien uutisointia, vuokratyöyritysten markkinointimateriaaleja, sekä vuokratyöyritysten edustajien haastatteluita. Analyysimenetelmänä käytän kriittistä diskurssianalyysia. Tämä menetelmä mahdollistaa puheen ja dokumenttien tarkastelun sosiaalisena toimintana, jolla eri toimijat pyrkivät osallistumaan yhteiskunnassa hyväksyttyjen ja tunnustettujen käsitysten ja toimintavaihtoehtojen rakentamis-, tulkinta- ja määrittelyprosesseihin. Tutkimukseni päätuloksena esitän, että vuokratyöstä muodostui legitiimi tapa työllistää Suomessa 1990-luvulla, koska vuokratyö käsitteellistettiin sekä lainsäädännön että median diskursseissa ennen kaikkea ratkaisuksi työttömyyteen. Toisaalta vuokratyö käsitteellistettiin vain marginaalisten työntekijäryhmien (naiset ja opiskelijat) rooliksi, jolloin se ei liittynyt miesvaltaisten työpaikkojen arkeen. Ratkaisuna työttömyyteen vuokratyö myös samalla luonnollistettiin osaksi yleisempää työmarkkinakehitystä, jolle ”kukaan ei voi mitään”. 2000-luvulla vuokratyö jatkoi voittokulkuaan ja rakentui pysyväksi ilmiöksi, koska työlainsäädännön uudistus institutionalisoi vuokratyön työehtosopimusmenettelyyn, jolloin sen ”salonkikelpoisuus” ja normaalius vahvistettiin. Vaikka työehtosopimusasia oli ratkaisuna merkittävä, nousi vuokratyön osalta itse työehtosopimus tärkeämmäksi kuin sen sisältö. Työehtosopimuksilla ei kuitenkaan pystytty vaikuttamaan esimerkiksi vuokratyöntekijän olemattomaan työsuhdeturvaan. Lisäksi työnantajapuhe käsitteellistää vuokratyön 2000-luvulla ennen kaikkea työmarkkinavaihtoehdoksi, vapautta ja monipuolisia työkokemuksia tarjoavaksi työmarkkinoiden katalysaattoriksi. Vuokratyö on tässä merkitysavaruudessa työntekijöille ”vain” yksi tapa työllistyä ja löytää oma tiensä työmarkkinoille, ei suinkaan työnantajien sanelema pakko. Työntekijöihin kohdistuva hallintapuhe niin mediassa kuin työnantajien haastatteluissakin pyrkii puolestaan rakentamaan ideaalityöntekijäkuvaksi yrittäjämäisen oman elämänsä toimitusjohtajan. Työnantajien diskursseissa kaikuvatkin työntekijään kohdistuva vaatimus itse itsensä ohjaamisesta sekä työntekijäidentiteetin muotoilemisesta joustavuutta, sopeutuvuutta, vaihtelua ja jatkuvaa muutosta vähintäänkin sietäväksi, mutta mieluiten näitä ominaisuuksia jopa aktiivisesti hakevaksi ja arvostavaksi. Työmarkkinoiden toimijana on nimenomaisesti yksilö, jonka mahdollisuudet menestyä ovat vain ja ainoastaan hänen omissa käsissään. Työntekijän roolin korostaminen aktiivisena toimijana ja vuokratyöstä ”oikeita”, norminmukaisia sisältöjä löytävänä pärjääjänä on diskursiivisesti hallittua yritystä ohjata työntekijöitä näkemään sekä itsensä tietynlaisina toimijoina että työmarkkinat tietyllä tavalla toimivina. Vuokratyössä ei ole kyse vain työntekijöiden yksilöllisistä tai yksittäisistä kokemuksista. Vuokratyö on yhteiskunnallisen merkityskamppailun tulos, jossa käyttövoimana ovat toimineet hallinnalliset ja säätelyyn pyrkivät käsitteellistykset työllisyydestä, yksilön valinnasta ja koko yhteiskunnan edusta. Hallinnan ja säätelyn näkökulmasta katsottuna vuokratyö on myös merkinnyt säätelyn liukumista tasa-arvoa, yhdenmukaista kohtelua ja työntekijän suojelua korostavasta viranomaisten ja poliittisten toimijoiden suorittamasta työmarkkinoiden kollektiivisesta säätelystä työnantajien ylläpitämään työntekijän persoonan ja käyttäytymisen hegemoniseen, yksilölliseen säätelyyn.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Vibrations in Rotating Machinery Arising from Minor Imperfections in Component Geometries

Vibrations in machines can cause noise, decrease the performance, or even damage the machine. Vibrations appear if there is a source of vibration that excites the system. In the worst case scenario, the excitation frequency coincides with the natural frequency of the machine causing resonance. Rotating machines are a machine type, where the excitation arises from the machine itself. The excitation originates from the mass imbalance in the rotating shaft, which always exists in machines that are manufactured using conventional methods. The excitation has a frequency that is dependent on the rotational speed of the machine. The rotating machines in industrial use are usually designed to rotate at a constant rotational speed, the case where the resonances can be easily avoided. However, the machines that have a varying operational speed are more problematic due to a wider range of frequencies that have to be avoided. Vibrations, which frequencies equal to rotational speed frequency of the machine are widely studied and considered in the typical machine design process. This study concentrates on vibrations, which arise from the excitations having frequencies that are multiples of the rotational speed frequency. These vibrations take place when there are two or more excitation components in a revolution of a rotating shaft. The dissertation introduces four studies where three kinds of machines are experiencing vibrations caused by different excitations. The first studied case is a directly driven permanent magnet generator used in a wind power plant. The electromagnetic properties of the generator cause harmonic excitations in the system. The dynamic responses of the generator are studied using the multibody dynamics formulation. In another study, the finite element method is used to study the vibrations of a magnetic gear due to excitations, which frequencies equal to the rotational speed frequency. The objective is to study the effects of manufacturing and assembling inaccuracies. Particularly, the eccentricity of the rotating part with respect to non-rotating part is studied since the eccentric operation causes a force component in the direction of the shortest air gap. The third machine type is a tube roll of a paper machine, which is studied while the tube roll is supported using two different structures. These cases are studied using different formulations. In the first case, the tube roll is supported by spherical roller bearings, which have some wavinesses on the rolling surfaces. Wavinesses cause excitations to the tube roll, which starts to resonate at the frequency that is a half of the first natural frequency. The frequency is in the range where the machine normally operates. The tube roll is modeled using the finite element method and the bearings are modeled as nonlinear forces between the tube roll and the pedestals. In the second case studied, the tube roll is supported by freely rotating discs, which wavinesses are also measured. The above described phenomenon is captured as well in this case, but the simulation methodology is based on the flexible multibody dynamics formulation. The simulation models that are used in both of the last two cases studied are verified by measuring the actual devices and comparing the simulated and measured results. The results show good agreement.

Comparison of Different Concentrated Solar Power Collector Designs and Development of a Linear Fresnel Solar Collector Model

Concentrated solar power (CSP) is a renewable energy technology, which could contribute to overcoming global problems related to pollution emissions and increasing energy demand. CSP utilizes solar irradiation, which is a variable source of energy. In order to utilize CSP technology in energy production and reliably operate a solar field including thermal energy storage system, dynamic simulation tools are needed in order to study the dynamics of the solar field, to optimize production and develop control systems. The object of this Master’s Thesis is to compare different concentrated solar power technologies and configure a dynamic solar field model of one selected CSP field design in the dynamic simulation program Apros, owned by VTT and Fortum. The configured model is based on German Novatec Solar’s linear Fresnel reflector design. Solar collector components including dimensions and performance calculation were developed, as well as a simple solar field control system. The preliminary simulation results of two simulation cases under clear sky conditions were good; the desired and stable superheated steam conditions were maintained in both cases, while, as expected, the amount of steam produced was reduced in the case having lower irradiation conditions. As a result of the model development process, it can be concluded, that the configured model is working successfully and that Apros is a very capable and flexible tool for configuring new solar field models and control systems and simulating solar field dynamic behaviour.

Roll-to-roll atomic layer deposition process for flexible electronics applications

Atomic Layer Deposition (ALD) is the technology of choice where very thin and highquality films are required. Its advantage is its ability to deposit dense and pinhole-free coatings in a controllable manner. It has already shown promising results in a range of applications, e.g. diffusion barrier coatings for OLED displays, surface passivation layers for solar panels. Spatial Atomic Layer Deposition (SALD) is a concept that allows a dramatic increase in ALD throughput. During the SALD process, the substrate moves between spatially separated zones filled with the respective precursor gases and reagents in such a manner that the exposure sequence replicates the conventional ALD cycle. The present work describes the development of a high-throughput ALD process. Preliminary process studies were made using an SALD reactor designed especially for this purpose. The basic properties of the ALD process were demonstrated using the wellstudied Al2O3 trimethyl aluminium (TMA)+H2O process. It was shown that the SALD reactor is able to deposit uniform films in true ALD mode. The ALD nature of the process was proven by demonstrating self-limiting behaviour and linear film growth. The process behaviour and properties of synthesized films were in good agreement with previous ALD studies. Issues related to anomalous deposition at low temperatures were addressed as well. The quality of the coatings was demonstrated by applying 20 nm of the Al2O3 on to polymer substrate and measuring its moisture barrier properties. The results of tests confirmed the superior properties of the coatings and their suitability for flexible electronics encapsulation. Successful results led to the development of a pilot scale roll-to-roll coating system. It was demonstrated that the system is able to deposit superior quality films with a water transmission rate of 5x10-6 g/m2day at a web speed of 0.25 m/min. That is equivalent to a production rate of 180 m2/day and can be potentially increased by using wider webs. State-of-art film quality, high production rates and repeatable results make SALD the technology of choice for manufacturing ultra-high barrier coatings for flexible electronics.

Use of the Wasserman equation in optimization of the duration of the power ramp in a cardiopulmonary exercise test: a study of Brazilian men

This study aimed to analyze the agreement between measurements of unloaded oxygen uptake and peak oxygen uptake based on equations proposed by Wasserman and on real measurements directly obtained with the ergospirometry system. We performed an incremental cardiopulmonary exercise test (CPET), which was applied to two groups of sedentary male subjects: one apparently healthy group (HG, n=12) and the other had stable coronary artery disease (n=16). The mean age in the HG was 47±4 years and that in the coronary artery disease group (CG) was 57±8 years. Both groups performed CPET on a cycle ergometer with a ramp-type protocol at an intensity that was calculated according to the Wasserman equation. In the HG, there was no significant difference between measurements predicted by the formula and real measurements obtained in CPET in the unloaded condition. However, at peak effort, a significant difference was observed between oxygen uptake (V˙O2)peak(predicted)and V˙O2peak(real)(nonparametric Wilcoxon test). In the CG, there was a significant difference of 116.26 mL/min between the predicted values by the formula and the real values obtained in the unloaded condition. A significant difference in peak effort was found, where V˙O2peak(real)was 40% lower than V˙O2peak(predicted)(nonparametric Wilcoxon test). There was no agreement between the real and predicted measurements as analyzed by Lin’s coefficient or the Bland and Altman model. The Wasserman formula does not appear to be appropriate for prediction of functional capacity of volunteers. Therefore, this formula cannot precisely predict the increase in power in incremental CPET on a cycle ergometer.

Political economy of preferential trade agreement: the case of bilateral asymmetric negotiation

The purpose of this paper is to analyse the political economy of preferential trade agreements based on a sequential non-cooperative Stackelberg political game between a large economy and a small one, in which the political dispute of rival lobby groups defines the unilateral stance of both governments in the first stage; and the Stackelberg "coalition-proof" equilibrium defines the free trade agreement format in the second stage. Finally, a few modifications in the initial game structure are discussed in order to enhance the small economy's negotiation power. The political economy model is applied to FTAA case.

Between Dugin’s Eurasianism and Mahan’s Sea Power Concept: Russia’s Geopolitical Discourse within Foucault’s ‘Discursive Tree’ before and After the Incorporation of the Crimea

The fall of 2013 could be characterized as a crossroad in the geopolitics of Eastern Europe, namely Ukraine. Two rivalry geopolitical projects have been developing throughout the post-Cold War years, and it seems that they reached a collision point in Ukraine; a country whose authorities have been for long switching sides between the European Union and the Russian Federation in their foreign policy commitments. The refusal/postponing to sign the Association Agreement with Brussels, an expected event by a large category of the Ukrainian society, by Yanukovich’s government led to the outset of the latter; and brought a pro-Western, anti-Russian government in Kyiv. It seems that Ukraine, after those events, has embarked definitively on the path of integration into the West (European Union and possibly NATO). The Russian Federation, who has been throughout Putin’s years engaged into the re-integration of post-Soviet space, reacted to these developments in an assertive manner by violating borders, agreements and the territorial integrity of Ukraine. Thus, the incorporation of the Crimea into the Russian Federation is the first in its kind in the post-Soviet space, despite the existence of various other conflicts that broke out in the region after the Soviet Union broke up. I will investigate in this thesis the nature of what will be labelled, in this work, the Crimean issue. I argue that the incorporation of the Crimean peninsula into the Russian Federation marks a new era in Russian geopolitical thinking that shapes, to a far extent, Russian foreign policy. Discourse analysis will be the methodological basis for this study, with a special focus on Michel Foucault’s Archaeology of Knowledge. The innovation that this research brings is the fact that it discusses Russian geopolitical discourse within the scope of Foucault’s ‘discursive tree’, with a reference to the Crimean issue. A wide range of primary sources will be consulted in this study such as presidential addresses to the Federal Assembly (2000-2014), Foreign Policy Concepts of the Russian Federation (2000, 2008), Russian maritime doctrines, as wells as Dugin’s Osnovy Geopolitiki (Foundations of Geopolitics), Mahan’s (The Influence of Sea Power Upon History, 1660–1783) and other Eurasianism related literature.

Bargaining Power Dynamics and the Negotiation of Commercial Rights and Obligations: A Case of Athlete Agreements

This qualitative case study explored how the structural power imbalance in high performance sport influenced the bargaining process and resulting commercial rights and obligations of a single Canadian national sport organization’s (NSO1) Athlete Agreement. Principles comprising the doctrine of unconscionability, specifically the identification of a power imbalance between contracting parties, and the exploration of how that power imbalance influenced the terms of the contract, provided a framework to analyze factors influencing the commercial contents of NSO1’s Athlete Agreement. The results of this analysis revealed that despite the overarching influence of the inherent structural power imbalance on all aspects of NSO1 and its membership, an athletes’ level of commercial appeal can reach such heights as to balance the bargaining positions of both parties and subsequently influence the commercial contents of the Athlete Agreement.

Indigenous knowledges and power in friction with human rights and development discourses : the case of the Witoto Ethnic Safeguarding Plan in the Colombian Amazon

Cette thèse analyse les négociations interculturelles des Gens du Centre (groupe amazonien multi-ethnique) avec les discours universels de droits humains et de développement mobilisés par l’État colombien. L’analyse se concentre sur le Plan de sauvegarde ethnique Witoto chapitre Leticia (ESP), qui est un des 73 plans formulés et implémentés par l’État colombien pour reconnaître les droits des peuples autochtones en danger par le déplacement forcé causé par les conflits armés internes. J’analyse l’ESP à travers la notion de friction (Tsing, 2005) qui fait référence aux caractéristiques complexes, inégalitaires et changeantes des rencontres contemporaines entre les différences des savoirs locaux et globaux. Mon analyse se base aussi sur des approches foucaldiennes et/ou subalternes de pouvoir comme la recherche anticoloniale et de la décolonisation, les perspectives critiques et contre-hégémoniques des droits humains, le post-développement, et les critiques du féminisme au développement. L’objectif de la thèse est d’analyser les savoirs (concepts de loi, de justice et de développement); les logiques de pensée (pratiques, épistémologies, rôles et espaces pour partager et produire des savoirs); et les relations de pouvoir (formes de leadership, associations, réseaux, et formes d’empowerment et disempowerment) produits et recréés par les Gens du Centre au sein des frictions avec les discours de droits humains et du développement. La thèse introduit comment la région habitée par les Gens du Centre (le Milieu Amazone transfrontalier) a été historiquement connectée aux relations inégalitaires de pouvoir qui influencent les luttes actuelles de ce groupe autochtone pour la reconnaissance de leurs droits à travers l’ESP. L’analyse se base à la fois sur une recherche documentaire et sur deux terrains ethnographiques, réalisés selon une perspective critique et autoréflexive. Ma réflexion méthodologique explore comment la position des chercheurs sur le terrain influence le savoir ethnographique et peut contribuer à la création des relations interculturelles inclusives, flexibles et connectées aux besoins des groupes locaux. La section analytique se concentre sur comment le pouvoir circule simultanément à travers des échelles nationale, régionale et locale dans l’ESP. J’y analyse comment ces formes de pouvoir produisent des sujets individuels et collectifs et s’articulent à des savoirs globaux ou locaux pour donner lieu à de nouvelles formes d’exclusion ou d’émancipation des autochtones déplacés. Les résultats de la recherche suggèrent que les Gens du Centre approchent le discours des droits humains à travers leurs savoirs autochtones sur la « loi de l’origine ». Cette loi établit leur différence culturelle comme étant à la base du processus de reconnaissance de leurs droits comme peuple déplacé. D’ailleurs, les Gens du Centre approprient les discours et les projets de développement à travers la notion d’abondance qui, comprise comme une habileté collective qui connecte la spiritualité, les valeurs culturelles, et les rôles de genre, contribue à assurer l’existence physique et culturelle des groupes autochtones. Ma thèse soutient que, même si ces savoirs et logiques de pensée autochtones sont liés à des inégalités et à formes de pouvoir local, ils peuvent contribuer à des pratiques de droits humains et de développement plurielles, égalitaires et inclusives.

The long-term EU budget: size or flexibility? Bruegel Policy Contribution 2012/20, November 2012

The EU is in the process of negotiating its 2014-20 financial framework. Failure to reach an agreement would imply a delay in the preparation of the strategic plans each member state puts together to explain how it will use Structural and Cohesion Funds. Even if solutions are found – for example annual renewals of the budget based on the previous year's figures – there will be political and institutional costs. EU leaders have too often and too forcefully advocated the use of the EU budget for growth to be able to drop the idea without consequences. • The overwhelming attention paid to the size of the budget is misplaced. EU leaders should instead aim to make the EU budget more flexible, safeguard it from future political power struggles, and reinforce assessment of the impact of EU funded growth policies. • To improve flexibility a commitment device should be created that places the EU budget above continuous political disagreement. We suggest the creation of a European Growth Fund, on the basis of which the European Commission should be allowed to borrow on capital markets to anticipate pre-allocated EU expenditure, such as Structural and Cohesion Funds. Markets would thus be a factor in EU budget policymaking, with a potentially disciplining effect. Attaching conditionality to this type of disbursement appears legitimate, as capital delivered in this way is a form of assistance.