Treatment of Domestic Sewage in an Anaerobic-Aerobic Fixed-bed Reactor with Recirculation of the Liquid Phase

This study reports the performance of a combined anaerobic-aerobic packed-bed reactor that can be used to treat domestic sewage. Initially, a bench-scale reactor was operated in three experimental phases. In the first phase, the anaerobic reactor was operated with an average organic matter removal efficiency of 77% for a hydraulic retention time (HRT) of 10 h. In the second phase, the reactor was operated with an anaerobic stage followed by an aerobic zone, resulting in a mean value of 91% efficiency. In the third and final phase, the anaerobic-aerobic reactor was operated with recirculation of the effluent of the reactor through the anaerobic zone. The system yielded mean total nitrogen removal percentages of 65 and 75% for recycle ratios (r) of 0.5 and 1.5, respectively, and the chemical oxygen demand (COD) removal efficiencies were higher than 90%. When the pilot-scale reactor was operated with an HRT of 12 h and r values of 1.5 and 3.0, its performance was similar to that observed in the bench-scale unit (92% COD removal for r = 3.0). However, the nitrogen removal was lower (55% N removal for r = 3.0) due to problems with the hydrodynamics in the aerobic zone. The anaerobic-aerobic fixed-bed reactor with recirculation of the liquid phase allows for concomitant carbon and nitrogen removal without adding an exogenous source of electron donors and without requiring any additional alkalinity supplementation.

Comparison of numerical and physical hydraulic models, Masonboro Inlet, North Carolina : Appendix 1, fixed-bed hydraulic model results /

"June 1977."

Supplementary tests of Masonboro Inlet fixed-bed model : hydraulic model investigation /

"General investigation of tidal inlets; a program of research conducted jointly by U.S. Army Coastal Engineering Research Center, Fort Belvoir, Virginia [and] U.S. Army Engineer Waterways Experiment Station, Vicksburg, Mississippi."

Fixed bed downdraft gasification of paper industry wastes

The two main wastes generated from secondary fibre paper mills are rejects (composed mainly of plastics and fibres) and de-inking sludge, both of which are evolved from the pulping process during paper manufacture. The current practice for the disposal of these wastes is either by land-spreading or land-filling. This work explores the gasification of blends of pre-conditioned rejects and de-inking sludge pellets with mixed wood chips in an Imbert type fixed bed downdraft gasifier with a maximum feeding capacity of 10kg/h. The producer gases evolved would generate combined heat and power (CHP) in an internal combustion engine. The results show that as much as 80wt.% of a brown paper mill's rejects (consisting of 20wt.% mixed plastics and 80wt.% paper fibres) could be successfully gasified in a blend with 20wt.% mixed wood chips. The producer gas composition was 16.24% H, 23.34% CO, 12.71% CO 5.21% CH and 42.49% N (v/v%) with a higher heating value of 7.3MJ/Nm. After the removal of tar and water condensate the producer gas was of sufficient calorific value and flow rate to power a 10kWe gas engine. Some blends using rejects from other mill types were not successful, and the limiting factor was usually the agglomeration of plastics present within the fuel.

Element characteristic tolerance for semi-batch fixed bed biomass pyrolysis

Biomass pyrolysis to bio-oil is one of the promising sustainable fuels. In this work, relation between biomass feedstock element characteristic and crude bio-oil production yield and lower heating value was explored. The element characteristics considered in this study include moisture, ash, fix carbon, volatile matter, C, H, N, O, S, cellulose, hemicellulose, and lignin content. A semi-batch fixed bed reactor was used for biomass pyrolysis with heating rate of 30 °C/min from room temperature to 600 °C and the reactor was held at 600 °C for 1 h before cooling down. Constant nitrogen flow (1bar) was provided for anaerobic condition. Sago and Napier glass were used in the study to create different element characteristic of feedstock by altering mixing ratio. Comparison between each element characteristic to crude bio-oil yield and low heating value was conducted. The result suggested potential key element characteristic for pyrolysis and provide a platform to access the feedstock element acceptance range.

Pyrolysis of Napier grass in a fixed bed reactor:effect of operating conditions on product yields and characteristic

This study presents a report on pyrolysis of Napier grass stem in a fixed bed reactor. The effects of nitrogen flow (20 to 60 mL/min), and reaction temperature (450 to 650 degrees C) were investigated. Increasing the nitrogen flow from 20 to 30 mL/min increased the bio-oil yield and decreased both bio-char and non-condensable gas. 30 mL/min nitrogen flow resulted in optimum bio-oil yield and was used in the subsequent experiments. Reaction temperatures between 450 and 600 degrees C increased the bio-oil yield, with maximum yield of 32.26 wt% at 600 degrees C and a decrease in the corresponding bio-char and non-condensable gas. At 650 degrees C, reductions in the bio-oil and bio-char yields were recorded while the non-condensable gas increased. Water content of the bio-oil decreased with increasing reaction temperature, while density and viscosity increased. The observed pH and higher heating values were between 2.43 to 2.97, and 25.25 to 28.88 MJ/kg, respectively. GC-MS analysis revealed that the oil was made up of highly oxygenated compounds and requires upgrading. The bio-char and non-condensable gas were characterized, and the effect of reaction temperature on the properties was evaluated. Napier grass represents a good source of renewable energy when all pyrolysis products are efficiently utilized.

Assessment of naproxen adsorption on bone char in aqueous solutions using batch and fixed-bed processes

An integrated analysis of naproxen adsorption on bone char in batch and packed-bed column conditions has been performed. Kinetic, thermodynamic and breakthrough parameters have been calculated using adsorption models and artificial neural networks. Results show that naproxen removal using bone char in batch conditions is a feasible and effective process, which could involve electrostatic and non-electrostatic interactions depending mainly on pH conditions. However, the application of packed-bed column for naproxen adsorption on bone char is not effective for the treatment of diluted solutions due to the low degree of adsorbent utilization (below 4%) at tested operating conditions. The proposed mechanism for naproxen removal using bone char could include a complexation process via phosphate and naproxen, hydrogen bonding and the possibility of hydrophobic interactions via π–π electron. This study highlights the relevance of performing an integrated analysis of adsorbent effectiveness in batch and dynamic conditions to establish the best process configuration for the removal of emerging water pollutants such as pharmaceuticals.

Removal of paracetamol on biomass-derived activated carbon: Modeling the fixed bed breakthrough curves using batch adsorption experiments

The remediation of paracetamol (PA), an emerging contaminant frequently found in wastewater treatment plants, has been studied in the low concentration range (0.3–10 mg L−1) using as adsorbent a biomass-derived activated carbon. PA uptake of up to 100 mg g−1 over the activated carbon has been obtained, with the adsorption isotherms being fairly explained by the Langmuir model. The application of Reichemberg and the Vermeulen equations to the batch kinetics experiments allowed estimating homogeneous and heterogeneous diffusion coefficients, reflecting the dependence of diffusion with the surface coverage of PA. A series of rapid small-scale column tests were carried out to determine the breakthrough curves under different operational conditions (temperature, PA concentration, flow rate, bed length). The suitability of the proposed adsorbent for the remediation of PA in fixed-bed adsorption was proven by the high PA adsorption capacity along with the fast adsorption and the reduced height of the mass transfer zone of the columns. We have demonstrated that, thanks to the use of the heterogeneous diffusion coefficient, the proposed mathematical approach for the numerical solution to the mass balance of the column provides a reliable description of the breakthrough profiles and the design parameters, being much more accurate than models based in the classical linear driving force.

Drying of rye (Lolium miltiflorum l.) in fixed bed with parallel air flow.

This work aimed to study the drying of ryegrass seeds (Lolium multiflorum L.) in fixed bed dryer with parallel air flow.

HYGROSCOPIC PROPERTIES OF ORANGE PULP AND PEEL

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Hydrogen sulphide removal from air by biotrickling filter using open-pore polyurethane foam as a carrier

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Biometanazione della frazione organica di rifiuti solidi urbani da raccolta indifferenziata mediante codigestione con refluo zootecnico o addizione di solfuro di sodio

Il presente elaborato è stato finalizzato allo sviluppo di un processo di digestione anaerobica della frazione organica dei rifiuti solidi urbani (FORSU oppure, in lingua inglese OFMSW, Organic Fraction of Municipal Solid Waste) provenienti da raccolta indifferenziata e conseguente produzione di biogas da impiegarsi per il recupero energetico. Questo lavoro rientra nell’ambito di un progetto, cofinanziato dalla Regione Emilia Romagna attraverso il Programma Regionale per la Ricerca Industriale, l’Innovazione e il Trasferimento Tecnologico (PRRIITT), sviluppato dal Dipartimento di Chimica Applicata e Scienza dei Materiali (DICASM) dell’Università di Bologna in collaborazione con la Facoltà di Ingegneria dell’Università di Ferrara e con la società Recupera s.r.l. che applicherà il processo nell’impianto pilota realizzato presso il proprio sito di biostabilizzazione e compostaggio ad Ostellato (FE). L’obiettivo è stato la verifica della possibilità di impiegare la frazione organica dei rifiuti indifferenziati per la produzione di biogas, e in particolare di metano, attraverso un processo di digestione anaerobica previo trattamento chimico oppure in codigestione con altri substrati organici facilmente fermentabili. E’ stata inoltre studiata la possibilità di impiego di reattori con biomassa adesa per migliorare la produzione specifica di metano e diminuire la lag phase. Dalla sperimentazione si può concludere che è possibile giungere allo sviluppo di metano dalla purea codigerendola assieme a refluo zootecnico. Per ottenere però produzioni significative la quantità di solidi volatili apportati dal rifiuto non deve superare il 50% dei solidi volatili complessivi. Viceversa, l’addizione di solfuri alla sola purea si è dimostrata ininfluente nel tentativo di sottrarre gli agenti inibitori della metanogenesi. Inoltre, l’impiego di supporti di riempimento lavorando attraverso processi batch sequenziali permette di eliminare, nei cicli successivi al primo, la lag phase dei batteri metanogeni ed incrementare la produzione specifica di metano.

Dehydrogenation of Butyl Alcohol in Fixed Catalyst Beds

The vapor-phase dehydrogenation of 1 -butanol to butyraldehyde was studied in a fixed bed of catalyst from 250° to 360° C. Of all the catalysts studied during preliminary investigation, the one containing 90% copper, 8% chromia, and 2% carbon supported on pumice was best, with high activity and selectivity. The data are expressed in the form of a first-order irreversible reaction rate equation. Single-site surface reaction (hydrogen adsorbed) is the rate-controlling mechanism at all the temperatures studied. The rate data obtained in the entire range of experimental conditions fit the rate equation based on this mechanism with a standard deviation of ± 22.8%.

A study of carbon deposition on catalysts during the catalytic partial oxidation of methane to syngas in a fluidized bed

The deposition of carbon on catalysts during the partial oxidation of methane to syngas has been investigated in a fluidized bed. It was found that the relative rate of carbon deposition follows the order NiP > >d > Pt, Rh. Although the rate of carbon deposition in the fluidized bed was much lower than that in the fixed bed, carbon deposition could still be detected in the fluidized bed if a CH4/O-2 ratio in greater than 2.3 was used.