Synthesis and properties of aromatic polyimides derived from 2,2,' 3,3 '-biphenyltetracarboxylic dianhydride

2,2,'3,3' -Biphenyltetracarboxylic dianhydride (2,2,'3,3'-BPDA) was prepared by a coupling reaction of dimethyl 3-iodophthalate. The X-ray single-crystal structure determination showed that this dianhydride had a bent and noncopolanar structure, presenting a striking contrast to its isomer, 3,3,'4,4'-BPDA. This dianhydride was reacted with aromatic diamines in a polar aprotic solvent such as N,N-dimethylacetamide (DMAc) to form polyamic acid intermediates, which imidized chemically to polyimides with inherent viscosities of 0.34-0.55 dL/g, depending on the diamine used. The polyimides from 2,2,'3,3'-BPDA exhibited a good solubility and were dissolved in polar aprotic solvents and polychlorocarbons. These polyimides have high glass transition temperatures above 283 degrees C. Thermogravimetric analyses indicated that these polyimides were fairly stable up to 500 degrees C, and the 5% weight loss temperatures were recorded in the range of 534-583 degrees C in nitrogen atmosphere and 537-561 degrees C in air atmosphere. All polyimides were amorphous according to X-ray determination. (C) 1999 John Wiley & Sons, Inc.

Luminescent properties of Ba-3(PO4)(2):Eu, Tb phosphors

Luminescence of europium (III), europium(II) and terbium(III) has been observed in Ba-3(PO4)(2):Eu, Tb phosphors which are synthesized in air atmosphere. The valence state of europium is influenced by amount of terbium. It is notable that the relative intensity of the emission spectra peaks corresponding to Eu2+ is increased if the amount of Tb3+ is increased. These phenomena can be explained by an electron transfer mechanism. We predict a new kind of two-rare-earth codoped trichromatic phosphors in Ba-3(PO4)(2) matrix.

The spectral properties of BaB8O13:Eu,Tb phosphors

The luminescence properties of BaB8O13:xEu,yTb phosphors which were synthesized in air atmosphere have been studied. The emissions of europium(III), terbium(III) and europium(II) have been observed in BaB8O13:xEu, yTb phosphors. Electron paramagnetic resonance (EPR) studies were carried out. The intensities of EPR peaks of europium(II) are increased if terbium(III) is increased in BaB8O13:Eu3+,yTb(3+) phosphors. So the valence state of europium is influenced by terbium(III). These phenomena can be explained by an electron transfer mechanism. We found a new kind of method to prepare trichromatic phosphor that two rare earth ions activated in a BaB8O13 matrix.

Luminescence properties of SrB4O7: Eu, Tb phosphors

In this paper, the luminescence properties of SrB4O7: xEu, yTb phosphors were investigated. The SrB4O7: xEu, yTb phosphors were first synthesized in air atmosphere, and the emission spectra of Eu2+, Eu3+ and Tb3+ ions have been observed in phosphors. We found that the relative intensity of the emission of Eu2+ ion in the same matrix are increased when Tb3+ is incorporated in SrB4O7:Eu phosphor. So the valence state of europium is influenced by terbium. These phenomena can be explained using an electron transfer theory.

Electron transfer between Eu3+ and Tb3+ in BaB4O7 matrix

The BaB4O7:Eu, Tb phosphors are first synthesized in air atmosphere. We investigate their luminescent properties, and find that europium(II) and europium(III) can coexist in the BaB4O7:Eu phosphor. We observed that the relative intensity of europium(II) is increased when terbium(III) is incorporated. The electron spin resonance (ESR) spectra are carried out. The intensity of ESR peaks corresponding to europium(II) is also increased when terbium(III) is increased, so the valency state of europium is influenced by terbium(III). We explain these phenomena by an electron transfer mechanism. (C) 1996 Academic Press, Inc.

黄铁矿热转变过程的岩石磁学研究

Pyrite is the most stable iron-sulfide in reduced environment, and plays an important role in geochemical iron-sulfur cycling of sediments. Thus, the presence of pyrite in sediments and rocks is an important indicator of sedimentary environments. Previous studies on the thermal products of pyrite showed that all of the products (e.g., pyrrhotite, magnetite, hematite) have strong capability of carrying remanence. To deepen our understanding of the environmental and paleomagnetic significances of pyrite, the mineral transformation processes of pyrite upon heating were systematically investigated in this study using intergrated rock magnetic experiments (in both argon and air atmospheres) and X-ray diffraction analysis. The room temperature susceptibility of the paramagnetic pyrite is about 2.68×10-5 SI. In argon atmosphere (reducing environment), pyrite was transformed into monoclinic stable single domain (SD) pyrrhotite above 440 C. The corresponding coercive force and remanence coercivity are about 20 mT and 30 mT, respectively. In contrast, in air atmosphere (oxidation environment), the intermediate thermal products of pyrite are magnetite and pyrrhotite, which were quickly further oxidated to SD hematite, which has coercivity of about 1400 mT. In addition, the hematite particles gradually grow from SD to PSD grain size region by multiple heating runs. The transformation processes of pyrite in oxidation atomosphere can be interpreted by three possible pathways: (1) pyrite→magnetite→hematite; (2) pyrite→pyrrhotite→magnetite→hematite; and (3) pyrite→pyrrhotite→hematite. Low-temperature magnetic experiments show no transitions for pyrite. Despite that low-temperature magnetic method is not suitable for identification of pyrite, it is clear in this study that the high-temperature thermomagnetic measurements (e.g.,  -T and J-T curves) are very sensitive to the presence of pyrite in sediments and rocks. Nevertheless, for the thermal treatment products, low-temperature magnetic measurements showed the 34 K transition of pyrrhotite and the 250 K Morine transition of hematite. Iron-sulfide has also been found on Martian meteorolites by other workers. Therefore, systematic study of rock magnetism of pyrite (and other iron-sulfides) and their products will have great significances for both paleomagnetism and planetary magnetism.

Photoluminescence studies of spray pyrolytically grown nanostructured tin oxide semiconductor thin films on glass substrates

SnO2 nanocrystalline thin films were deposited on glass substrates by the spray pyrolysis technique in air atmosphere at 375, 400, 425, 450 and 500 ◦C substrate temperatures. The obtained films were characterized by using XRD. The room temperature photoluminescence (PL) spectra of these films have near band edge (NBE) and deep level emission under the excitation of 325 nm radiation. NBE PL peak intensity decreased consistently with temperatures for samples prepared at 400, 450 and 500 ◦C, while a sudden reduction in intensity is observed for the sample prepared at 425 ◦C. A similar effect was observed for the optical transmittance spectra. These effects can be explained on the basis of the change in population of oxygen vacancies as indicated by the change in a values

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Síntese de nanopartículas de magnetita via decomposição térmica em meio não-aquoso

This work aims at obtaining nanoparticles of iron oxide, the magnetite one (Fe3O4), via synthesis by thermal decomposition through polyol. Thus, two routes were evaluated: a simple decomposition route assisted by reflux and a hydrothermal route both without synthetic air atmosphere using a synthesis temperature of 260ºC. In this work observed the influence of the observe of surfactants which are generally applied in the synthesis of iron oxide nanoparticles decreasing cluster areas. Further, was observed pure magnetite phase without secondary phases generally found in the iron oxide synthesis, a better control of crystallite size, morphology, crystal structure and magnetic behavior. Finally, the introduction of hydroxyl groups on the nanoparticles surface was analyzed besides its employment in the polymer production with OH radicals. The obtained materials were characterized by XRD, DLS, VSM, TEM, TG and DSC analyses. The results for the magnetite obtainment with a particle size greater than 5 nm and smaller than 11 nm, well defined morphology and good magnetic properties with superparamagnetic behavior. The reflux synthesis was more efficient in the deposition of the hydroxyl groups on the nanoparticles surface

Estudo da síntese e propriedade magnética de ferritas de manganês/cobalto dopadas com níquel

For the chemical method of synthesis of co-precipitation were produced ferrite powders manganese-cobalt equal stoichiometric formula Mn (1-x) Co (x) Fe2O4, for 0 < x < 1, first reagent element using as the hydroxide ammonium and second time using sodium hydroxide. The obtained powders were calcined at 400 ° C, 650 ° C, 900 ° C and 1150 ° C in a conventional oven type furnace with an air atmosphere for a period of 240 minutes. Other samples were calcined at a temperature of 900 ° C in a controlled atmosphere of argon, to evaluate the possible influence of the atmosphere on the final results the structure and morphology. The samples were also calcined in a microwave oven at 400 ° C and 650 ° C for a period of 45 minutes possible to evaluate the performance of this type of heat treatment furnace. It was successfully tested the ability of this group include isomorphic ferrite with the inclusion of nickel cations in order to evaluate the occurrence of disorder in the crystalline structures and their changes in magnetic characteristics.To identify the structural, morphological, chemical composition and proportions, as well as their magnetic characteristics were performed characterization tests of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDX), thermogravimetric (TG), vibrating sample magnetometry (MAV) and Mössbauer spectroscopy. These tests revealed the occurrence of distortion in the crystal lattice, changes in magnetic response, occurrence of nanosized particles and superparamagnetism

Contribuições sobre estudos térmicos (TG/DTG, DTA, DSC e DSC-Fotovisual) da rifampicina e seus principais produtos de degradação

Since its synthesis over 48 years rifampicin has been extensively studied. The literature reports the characterization of thermal events for rifampicin in nitrogen atmosphere, however, no characterization in synthetic air atmosphere. This paper aims to contribute to the thermal study of rifampicin through thermal (TG / DTG, DTA, DSC and DSC - FOTOVISUAL ) and non-thermal (HPLC, XRPD , IR - FTIR , PCA) and its main degradation products ( rifampicin quinone , rifampicin N-oxide 3- formylrifamicin). Rifampicin study was characterized as polymorph form II from techniques DSC, IR and XRPD. TG curves for rifampicin in synthetic air atmosphere showed higher thermal stability than those in N2, when analyzed Ti and Ea. There was characterized as overlapping events melting and recrystallization under N2 with weight loss in the TG curve, suggesting concomitant decomposition. Images DSCFotovisual showed no fusion event and showed darkening of the sample during analysis. The DTA curve in synthetic air atmosphere was visually different from DTA and DSC curves under N2, suggesting the absence of recrystallization and melting or presence only decomposition. The IV - FTIR analysis along with PCA analysis and HPLC and thermal data suggest that rifampicin for their fusion is concomitant decomposition of the sample in N2 and fusion events and recrystallization do not occur in synthetic air atmosphere. Decomposition products studied in an air atmosphere showed no melting event and presented simultaneously to the decomposition initiation of heating after process loss of water and / or solvent, varying the Ti initiating events. The Coats - Redfern , Madsudhanan , Van Krevelen and Herwitz - Mertzger kinetic parameters for samples , through the methods of OZAWA , in an atmosphere of synthetic air and / or N2 rifampicin proved more stable than its degradation products . The kinetic data showed good correlation between the different models employed. In this way we contribute to obtaining information that may assist studies of pharmaceutical compatibility and stability of substances

Optical properties of polydisperse submicrometer aggregates of sulfur-containing zinc oxide consisting of spherical nanocrystallites

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural and morphological characteristics of (Pb1-x Sr (x) )TiO3 powders obtained by polymeric precursor method

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The influence of UV-C irradiation on the properties of thermoplastic starch and polycaprolactone biocomposite with sisal bleached fibers

The effect of UV-C irradiation of the TPS and PCL biocomposites with sisal bleached fibers was investigated. The biocomposite was UV-C irradiated at room temperature under air atmosphere. The structural and morphological changes produced when the films were exposed to UV irradiation for 142 h, were monitored using Scanning Electron Microscopy (SEM), Mechanical Tensile Tests, Differential Scanning Calorimetry (DSC), X-ray diffraction, Thermogravimetric analysis (TGA), and Fourier transform infra-red analysis (FTIR). Addition of 5-10% fibers in composites exhibited improved mechanical and thermal properties attributed to more efficient dispersibility of fiber in the matrix and good compatibility between fibers and the matrix polymer, however, after irradiated, the tensile properties decreased due to chain scission. The samples of irradiated PCL and IFS showed crystallinity increase, whereas the blend and composites showed a decrease in crystallinity. The DSC and X-ray diffraction studies suggested interaction between polymers in the blend via carboxyl groups in thermoplastic starch-PCL and hydroxyl groups in fibers. (C) 2011 Elsevier Ltd. All rights reserved.

Synthesis of (Ca,Nd)TiO3 powders by complex polymerization, Rietveld refinement and optical properties

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)