Dynamic characterisation of four nine-story large-panel R.C. buildings in Bishkek (Kyrgyzstan): A comparison between experimental ambient vibration analysis and numerical finite element modeling

With the outlook of improving seismic vulnerability assessment for the city of Bishkek (Kyrgyzstan), the global dynamic behaviour of four nine-storey r.c. large-panel buildings in elastic regime is studied. The four buildings were built during the Soviet era within a serial production system. Since they all belong to the same series, they have very similar geometries both in plan and in height. Firstly, ambient vibration measurements are performed in the four buildings. The data analysis composed of discrete Fourier transform, modal analysis (frequency domain decomposition) and deconvolution interferometry, yields the modal characteristics and an estimate of the linear impulse response function for the structures of the four buildings. Then, finite element models are set up for all four buildings and the results of the numerical modal analysis are compared with the experimental ones. The numerical models are finally calibrated considering the first three global modes and their results match the experimental ones with an error of less then 20%.

Modelling comminution patterns within a pilot scale AG/SAG mill

The patterns of rock comminution within tumbling mills, as well as the nature of forces, are of significant practical importance. Discrete element modelling (DEM) has been used to analyse the pattern of specific energy applied to rock, in terms of spatial distribution within a pilot AG/SAG mill. We also analysed in some detail the nature of the forces, which may result in rock comminution. In order to examine the distribution of energy applied within the mill, the DEM models were compared with measured particle mass losses, in small scale AG and SAG mill experiments. The intensity of contact stresses was estimated using the Hertz theory of elastic contacts. The results indicate that in the case of the AG mill, the highest intensity stresses and strains are likely to occur deep within the charge, and close to the base. This effect is probably more pronounced for large AG mills. In the SAG mill case, the impacts of the steel balls on the surface of the charge are likely to be the most potent. In both cases, the spatial pattern of medium-to-high energy collisions is affected by the rotational speed of the mill. Based on an assumed damage threshold for rock, in terms of specific energy introduced per single collision, the spatial pattern of productive collisions within each charge was estimated and compared with rates of mass loss. We also investigated the nature of the comminution process within AG vs. SAG mill, in order to explain the observed differences in energy utilisation efficiency, between two types of milling. All experiments were performed using a laboratory scale mill of 1.19 m diameter and 0.31 m length, equipped with 14 square section lifters of height 40 mm. (C) 2006 Elsevier Ltd. All rights reserved.

The role of material characterisation in the crush modelling of thermoplastic composite structures

The predictive capability of high fidelity finite element modelling, to accurately capture damage and crush behaviour of composite structures, relies on the acquisition of accurate material properties, some of which have necessitated the development of novel approaches. This paper details the measurement of interlaminar and intralaminar fracture toughness, the non-linear shear behaviour of carbon fibre (AS4)/thermoplastic Polyetherketoneketone (PEKK) composite laminates and the utilisation of these properties for the accurate computational modelling of crush. Double-cantilever-beam (DCB), four-point end-notched flexure (4ENF) and Mixed-mode bending (MMB) test configurations were used to determine the initiation and propagation fracture toughness in mode I, mode II and mixed-mode loading, respectively. Compact Tension (CT) and Compact Compression (CC) test samples were employed to determine the intralaminar longitudinal tensile and compressive fracture toughness. V-notched rail shear tests were used to measure the highly non-linear shear behaviour, associated with thermoplastic composites, and fracture toughness. Corresponding numerical models of these tests were developed for verification and yielded good correlation with the experimental response. This also confirmed the accuracy of the measured values which were then employed as input material parameters for modelling the crush behaviour of a corrugated test specimen.

A simple way to introduce fibers into FEM models

This communication proposes a simple way to introduce fibers into finite element modelling. This is a promising formulation to deal with fiber-reinforced composites by the finite element method (FEM), as it allows the consideration of short or long fibers placed arbitrarily inside a continuum domain (matrix). The most important feature of the formulation is that no additional degree of freedom is introduced into the pre-existent finite element numerical system to consider any distribution of fiber inclusions. In other words, the size of the system of equations used to solve a non-reinforced medium is the same as the one used to solve the reinforced counterpart. Another important characteristic is the reduced work required by the user to introduce fibers, avoiding `rebar` elements, node-by-node geometrical definitions or even complex mesh generation. An additional characteristic of the technique is the possibility of representing unbounded stresses at the end of fibers using a finite number of degrees of freedom. Further studies are required for non-linear applications in which localization may occur. Along the text the linear formulation is presented and the bounded connection between fibers and continuum is considered. Four examples are presented, including non-linear analysis, to validate and show the capabilities of the formulation. Copyright (c) 2007 John Wiley & Sons, Ltd.

Effects of hot intrusions on pore-fluid flow and heat transfer in fluid-saturated rocks

We use the finite element method to solve coupled problems between pore-fluid flow and heat transfer in fluid-saturated porous rocks. In particular, we investigate the effects of both the hot pluton intrusion and topographically driven horizontal flow on the distributions of the pore-flow velocity and temperature in large-scale hydrothermal systems. Since general mineralization patterns are strongly dependent on distributions of both the pore-fluid velocity and temperature fields, the modern mineralization theory has been used to predict the general mineralization patterns in several realistic hydrothermal systems. The related numerical results have demonstrated that: (1) The existence of a hot intrusion can cause an increase in the maximum value of the pore-fluid velocity in the hydrothermal system. (2) The permeability of an intruded pluton is one of the sensitive parameters to control the pore-fluid flow, heat transfer and ore body formation in hydrothermal systems. (3) The maximum value of the pore-fluid velocity increases when the bottom temperature of the hydrothermal system is increased. (4) The topographically driven flow has significant effects on the pore-fluid flow, temperature distribution and precipitation pattern of minerals in hydrothermal systems. (5) The size of the computational domain may have some effects on the pore-fluid flow and heat transfer, indicating that the size of a hydrothermal system may affect the pore-fluid flow and heat transfer within the system. (C) 2003 Elsevier Science B.V. All rights reserved.

Powder forging of a sintered Al-3.8Cu-1Mg-0.8Si-O.1Sn alloy

The forging characteristics of an Al-Cu-Mg-Si-Sn alloy are examined using it new testing strategy which incorporates a double truncated cone specimen and finite element modelling. This sample geometry produces controlled strain distributions within a single specimen and can readily identify the specific strain required to achieve a specific microstructural event by matching the metallographic data with the strain profiles calculated from finite element software, The friction conditions were determined using the conventional friction ring test, which was evaluated using finite element software. The rheological properties of the alloy, evaluated from compression testing of right cylinders, are similar to the properties of conventional aluminium forgings. A hoop strain develops at the outer diameter of the truncated cones and this leads to pore opening at the outer few millimetres. The porosity is effectively removed when the total strain equals the net compressive strain. The strain profiles that develop in the truncated cones are largely independent of the processing temperature and the strain rate although the strain required for pore closure increases as the forging temperature is reduced. This suggests that the microstructure and the strain rate sensitivity may also be important factors controlling pore behaviour. (C) 2002 Elsevier Science B.V. All rights reserved.

The effects of clinical support surfaces on pressure as a risk factor in the development of pressure ulcers, from a radiographical perspective: a narrative literature review

Purpose: Pressure ulcers are a high cost, high volume issue for health and medical care providers, having a detrimental effect on patients and relatives. Pressure ulcer prevention is widely covered in the literature, but little has been published regarding the risk to patients in the radiographical setting. This review of the current literature is to identify findings relevant to radiographical context. Methods: Literature searching was performed using Science Direct and Medline databases. The search was limited to articles published in the last ten years to remain current and excluded studies containing participants less than 17 years of age. In total 14 studies were acquired; three were excluded as they were not relevant. The remaining 11 studies were compared and reviewed. Discussion: Eight of the studies used ‘healthy’ participants and three used symptomatic participants. Nine studies explored interface pressure with a range of pressure mat technologies, two studies measured shear (MRI finite element modelling, and a non-invasive instrument), and one looked at blood flow and haemoglobin oxygenation. A range of surfaces were considered from trauma, nursing and surgical backgrounds for their ability to reduce pressure including standard mattresses, high specification mattresses, rigid and soft layer spine boards, various overlays (gel, air filled, foam). Conclusion: The current literature is not appropriate for the radiographic patient and cannot be extrapolated to a radiologic context. Sufficient evidence is presented in this review to support the need for further work specific to radiography in order to minimise the development of PU in at risk patients.

The Influence of Damping on Vibration Induced by High-Speed Trains

Passage of high-speed trains may induce high ground and track vibrations, which, besides increasing wheel, rail and track deterioration, may have a negative impact on the vehicle stability and on the passengers comfort. In this paper two distinct analyses are presented. The first one is dedicated to efficient decoupling of rail and soil vibrations by suggesting new interface materials in rail-sleeper fixing system, i.e. in the part where damping efficiency can be directly controlled and tested. The second analysis concerns with an adequate model of soils damping. Proper understanding and correct numerical simulation of this behaviour can help in suggesting soil improvement techniques.

Development of hybrid composite plate (HCP) for strengthening and repair of RC structures

Tese de Doutoramento em Engenharia Civil

Stability analysis of the 2007 Chehalis lake landslide based on long-range terrestrial photogrammetry and airborne LIDAR data

On December 4th 2007, a 3-Mm3 landslide occurred along the northwestern shore of Chehalis Lake. The initiation zone is located at the intersection of the main valley slope and the northern sidewall of a prominent gully. The slope failure caused a displacement wave that ran up to 38 m on the opposite shore of the lake. The landslide is temporally associated with a rain-on-snow meteorological event which is thought to have triggered it. This paper describes the Chehalis Lake landslide and presents a comparison of discontinuity orientation datasets obtained using three techniques: field measurements, terrestrial photogrammetric 3D models and an airborne LiDAR digital elevation model to describe the orientation and characteristics of the five discontinuity sets present. The discontinuity orientation data are used to perform kinematic, surface wedge limit equilibrium and three-dimensional distinct element analyses. The kinematic and surface wedge analyses suggest that the location of the slope failure (intersection of the valley slope and a gully wall) has facilitated the development of the unstable rock mass which initiated as a planar sliding failure. Results from the three-dimensional distinct element analyses suggest that the presence, orientation and high persistence of a discontinuity set dipping obliquely to the slope were critical to the development of the landslide and led to a failure mechanism dominated by planar sliding. The three-dimensional distinct element modelling also suggests that the presence of a steeply dipping discontinuity set striking perpendicular to the slope and associated with a fault exerted a significant control on the volume and extent of the failed rock mass but not on the overall stability of the slope.

Monte Carlo simulations of metasomatic enrichment in the lithosphere and implications for the source of alkaline basalts

One hypothesis for the origin of alkaline lavas erupted on oceanic islands and in intracontinental settings is that they represent the melts of amphibole-rich veins in the lithosphere (or melts of their dehydrated equivalents if metasomatized lithosphere is recycled into the convecting mantle). Amphibole-rich veins are interpreted as cumulates produced by crystallization of low-degree melts of the underlying asthenosphere as they ascend through the lithosphere. We present the results of trace-element modelling of the formation and melting of veins formed in this way with the goal of testing this hypothesis and for predicting how variability in the formation and subsequent melting of such cumulates (and adjacent cryptically and modally metasomatized lithospheric peridotite) would be manifested in magmas generated by such a process. Because the high-pressure phase equilibria of hydrous near-solidus melts of garnet lherzolite are poorly constrained and given the likely high variability of the hypothesized accumulation and remelting processes, we used Monte Carlo techniques to estimate how uncertainties in the model parameters (e.g. the compositions of the asthenospheric sources, their trace-element contents, and their degree of melting; the modal proportions of crystallizing phases, including accessory phases, as the asthenospheric partial melts ascend and crystallize in the lithosphere; the amount of metasomatism of the peridotitic country rock; the degree of melting of the cumulates and the amount of melt derived from the metasomatized country rock) propagate through the process and manifest themselves as variability in the trace-element contents and radiogenic isotopic ratios of model vein compositions and erupted alkaline magma compositions. We then compare the results of the models with amphibole observed in lithospheric veins and with oceanic and continental alkaline magmas. While the trace-element patterns of the near-solidus peridotite melts, the initial anhydrous cumulate assemblage (clinopyroxene +/- garnet +/- olivine +/- orthopyroxene), and the modelled coexisting liquids do not match the patterns observed in alkaline lavas, our calculations show that with further crystallization and the appearance of amphibole (and accessory minerals such as rutile, ilmenite, apatite, etc.) the calculated cumulate assemblages have trace-element patterns that closely match those observed in the veins and lavas. These calculated hydrous cumulate assemblages are highly enriched in incompatible trace elements and share many similarities with the trace-element patterns of alkaline basalts observed in oceanic or continental setting such as positive Nb/La, negative Ce/Pb, and similiar slopes of the rare earth elements. By varying the proportions of trapped liquid and thus simulating the cryptic and modal metasomatism observed in peridotite that surrounds these veins, we can model the variations in Ba/Nb, Ce/Pb, and Nb/U ratios that are observed in alkaline basalts. If the isotopic compositions of the initial low-degree peridotite melts are similar to the range observed in mid-ocean ridge basalt, our model calculations produce cumulates that would have isotopic compositions similar to those observed in most alkaline ocean island basalt (OIB) and continental magmas after similar to 0 center dot 15 Gyr. However, to produce alkaline basalts with HIMU isotopic compositions requires much longer residence times (i.e. 1-2 Gyr), consistent with subduction and recycling of metasomatized lithosphere through the mantle. such as a heterogeneous asthenosphere. These modelling results support the interpretation proposed by various researchers that amphibole-bearing veins represent cumulates formed during the differentiation of a volatile-bearing low-degree peridotite melt and that these cumulates are significant components of the sources of alkaline OIB and continental magmas. The results of the forward models provide the potential for detailed tests of this class of hypotheses for the origin of alkaline magmas worldwide and for interpreting major and minor aspects of the geochemical variability of these magmas.

Geometry, petrology and growth of a shallow crustal laccolith : the Torres del Paine Mafic Complex (Patagonia)

1. ABSTRACTS - RÉSUMÉSSCIENTIFIC ABSTRACT - ENGLISH VERSIONGeometry, petrology and growth of a shallow crustal laccolith: the Torres del Paine Mafi c Complex (Patagonia)The Torres del Paine intrusive complex (TPIC) is a composite mafic-granitic intrusion, ~70km2, belonging to a chain of isolated Miocene plutons in southern Patagonia. Their position is intermediate between the Mesozoic-Cenozoic calc-alkaline subduction related Patagonian batholith in the West and the late Cenozoic alkaline basaltic back-arc related plateau lavas in the East. The Torres del Paine complex formed during an important reconfiguration of the Patagonian geodynamic setting, with a migration of magmatism from the arc to the back-arc, possibly related to the Chile ridge subductionThe complex intruded the flysch of the Cretaceous Cerro Toro and Punta Barrosa Formations during the Miocene, creating a well-defined narrow contact aureole of 200-400 m width.In its eastern part, the Torres del Paine intrusive complex is a laccolith, composed of a succession of hornblende-gabbro to diorite sills at its base, with a total thickness of ~250m, showing brittle contacts with the overlying granitic sills, that form spectacular cliffs of more than 1000m. This laccolith is connected, in the western part, to its feeding system, with vertical alternating sheets of layered gabbronorite and Hbl-gabbro, surrounded and percolated by diorites. ID-TIMS U-Pb on zircons on feeder zone (FZ) gab- bros yield 12.593±0.009Ma and 12.587±0.009Ma, which is identifcal within error to the oldest granite dated so far by Michel et al. (2008). In contrast, the laccolith mafic complex is younger than than the youngest granite (12.50±0.02Ma), and has been emplaced from 12.472±0.009Ma to 12.431 ±0.006Ma, by under-accretion beneath the youngest granite at the interface with previously emplaced mafic sills.The gabbronorite crystallization sequence in the feeder zone is dominated by olivine, plagioclase, clinopyroxene and orthopyroxene, while amphibole forms late interstitial crystals. The crystallization sequence is identical in Hornblende-gabbro from the feeder zone, with higher modal hornblende. Gabbronorite and Hornblende-gabbro both display distinct Eu and Sr positive anomalies. In the laccolith, a lower Hornblende-gabbro crystallized in sills and evolved to a high alkali shoshonitic series. The Al203, Ti02, Na20, K20, Ba and Sr composition of these gabbros is highly variable and increases up to ~50wt% Si02. The lower hornblende-gabbro is characterized by kaersutite anhedral cores with inclusions of olivine, clino- and orthopyroxene and rare apatite and An70 plagioclase. Trace element modelling indicates that hornblende and clinopyroxene are in equilibrium with a liquid whose composition is similar to late basaltic trachyandesitic dikes that cut the complex. The matrix in the lower hornblende gabbro is composed of normally zoned oligoclase, Magnesio-hornblende, biotite, ilmenite and rare quartz and potassium feldspar. This assemblage crystallized in-situ from a Ba and Sr-depleted melts. In contrast, the upper Hbl-gabbro is high-K calc-alkaline. Poikilitic pargasite cores have inclusions of euhedral An70 plagioclase inclusions, and contain occasionally clinopyroxene, olivine and orthopyroxene. The matrix composition is identical to the lower hornblende-gabbro and similar to the diorite. Diorite bulk rock compositions show the same mineralogy but different modal proportions relative to hornblende-gabbrosThe Torres del Paine Intrusive Complex isotopic composition is 87Sr/86Sr=0.704, 143Nd/144Nd=0.5127, 206Pb/204Pb=18.70 and 207Pb/204Pb=15.65. Differentiated dioritic and granitic units may be linked to the gabbroic cumulates series, with 20-50% trapped interstitial melt, through fractionation of olivine-bearing gabbronorite or hornblende-gabbro fractionation The relative homogeneity of the isotopic compositions indicate that only small amounts of assimilation occurred. Two-pyroxenes thermometry, clinopyroxene barometry and amphibole-plagioclase thermometry was used to estimate pressure and temperature conditions. The early fractionation of ultramafic cumulates occurs at mid to lower crustal conditions, at temperatures exceeding 900°C. In contrast, the TPIC emplacement conditions have been estimated to ~0.7±0.5kbar and 790±60°C.Based on field and microtextural observations and geochemical modelling, fractionation of basaltic-trachyandesitic liquids at intermediate to lower crustal levels, has led to the formation of the Torres del Paine granites. Repetitive replenishment of basaltic trachy- andesitic liquid in crustal reservoirs led to mixed magmas that will ascend via the feeder zone, and crystallize into a laccolith, in the form of successive dioritic and gabbroic sills. Dynamic fractionation during emplacement concentrated hornblende rich cumulates in the center of individual sills. Variable degrees.of post-emplacement compaction led to the expulsion of felsic liquids that preferentially concentrated at the top of the sills. Incremental sills amalgamation of the entire Torres del Paine Intrusive Complex has lasted for ~160ka.RESUME SCIENTIFIQUE - VERSION FRANÇAISEGéométrie, pétrologie et croissance d'un laccolite peu profond : Le complexe ma- fique du Torres del Paine (Patagonie)Le Complexe Intrusif du Torres del Paine (CITP) est une intrusion bimodale, d'environ 70km2, appartenant à une chaîne de plutons Miocènes isolés, dans le sud de la Patago-nie. Leur position est intermédiaire entre le batholite patagonien calco-alcalin, à l'Ouest, mis en place au Mesozoïque-Cenozoïque dans un contexte de subduction, et les basal-tes andésitiques et trachybasaltes alcalins de plateau, plus jeune, à l'Est, lié à l'ouverture d'un arrière-arc.A son extrémité Est, le CITP est une succession de sills de gabbro à Hbl et de diorite, sur une épaisseur de ~250m, avec des évidences de mélange. Les contacts avec les sills de granite au-dessus, formant des parois de plus de 1000m, sont cassants. Ce laccolite est connecté, dans sa partie Ouest, à une zone d'alimentation, avec des intrusions sub-ver- ticales de gabbronorite litée et de gabbro à Hbl, en alternance. Celles-ci sont traversées et entourées par des diorites. Les zircons des gabbros de la zone d'alimentation, datés par ID-TIMS, ont cristallisés à 12.593±0.009Ma et 12.587±0.009Ma, ce qui correspond au plus vieux granite daté à ce jour par Michel et al. (2008). A l'inverse, les roches manques du laccolite se sont mises en place entre 12.472±0.009Ma et 12.431 ±0.006Ma, par sous-plaquage successifs à l'interface avec le granite le plus jeune daté à ce jour (12.50±0.02Ma).La séquence de cristallisation des gabbronorites est dominée par Ol, Plg, Cpx et Opx, alors que la Hbl est un cristal interstitiel. Elle est identique dans les gabbros à Hbl de la zone d'alimentation, avec ~30%vol de Hbl. Les gabbros de la zone d'alimentation montrent des anomalies positives en Eu et Sr distinctes. Dans le laccolite, le gabbro à Hbl inférieur évolue le long d'une série shoshonitique, riche en éléments incompatibles. Sa concentration en Al203, Ti02, Na20, K20, Ba et Sr est très variable et augmente rapide-ment jusqu'à ~50wt% Si02. Il est caractérisé par la présence de coeurs résorbés de kaer- sutite, entourés de Bt, et contenant des inclusions d'OI, Cpx et Opx, ou alors d'Ap et de rares Plg (An70). Hbl et Cpx ont cristallisés à partir d'un liquide de composition similaire aux dykes trachy-andesite basaltique du CITP. La matrice, cristallisée in-situ à partir d'un liquide pauvre en Ba et Sr, est composée d'oligoclase zoné de façon simple, de Mg-Hbl, Bt, llm ainsi que de rares Qtz et KF. Le gabbro à Hbl supérieur, quant à lui, appartient à une suite chimique calco-alcaline riche en K. Des coeurs poecilitiques de pargasite con-tiennent de nombreuses inclusions de Plg (An70) automorphe, ainsi que des Ol, Cpx et Opx. La composition de la matrice est identique à celle des gabbros à Hbl inférieurs et toutes deux sont similaires à la minéralogie des diorites. Les analyses sur roches totales de diorites montrent la même variabilité que celles de gabbros à Hbl, mais avec une ten-eur en Si02 plus élevée.La composition isotopique des liquides primitifs du CITP a été mesurée à 87Sr/86Sr=0.704, 143Nd/144Nd=0.5127, 206Pb/204Pb=18.70 et 207Pb/204Pb=15.65. Les granites et diorites différenciés peuvent être reliés à des cumulais gabbronoritiques (F=0.74 pour les granites et F=1-0.5 pour les diorites) et gabbroïques à Hbl (fractionnement supplémentaire pour les granites, avec F=0.3). La cristallisation de 20 à 50%vol de liquide interstitiel piégé dans les gabbros du CITP explique leur signature géochimique. Seules de faibles quantités de croûte continentale ont été assimilées. La température et la pression de fractionnement ont été estimées, sur la base des thermobaromètres Opx-Cpx, Hbl-Plg et Cpx, à plus de 900°C et une profondeur correspondant à la croûte inférieure-moyenne. A l'inverse, les conditions de cristallisation de la matrice des gabbros et diorites du laccolite ont été estimées à 790±60°C et ~0.7±0.5kbar.Je propose que les liquides felsiques du CITP se soient formés par cristallisation frac-tionnée en profondeur des assemblages minéralogiques observés dans les gabbros du CITP, à partir d'un liquide trachy-andesite basaltique. La percolation de magma dans les cristaux accumulés permet la remontée du mélange à travers la zone d'alimentation, vers le laccolite, où des sills se mettent en place successivement. L'amalgamation de sills dans le CITP a duré ~160ka.Le CITP s'est formé durant une reconfiguration importante du contexte géodynamique en Patagonie, avec un changement du magmatisme d'arc vers un volcanisme d'arrière- arc. Ce changement est certainement lié à la subduction de la ride du Chili.RESUME GRAND PUBLIC - VERSION FRANÇAISEGéométrie, pétrologie et croissance d'une chambre magmatique peu profonde : Le complexe mafique du Torres del Paine (Patagonie)Le pourtour de l'Océan Pacifique est caractérisé par une zone de convergence de plaques tectoniques, appelée zone de subduction, avec le plongement de croûte océa-nique sous les Andes dans le cas de la Patagonie. De nombreux volcans y sont associés, formant la ceinture de feu. Mais seuls quelques pourcents de tout le magma traversant la croûte terrestre parviennent à la surface et la majeure partie cristallise en profondeur, dans des chambres magmatiques. Quelles est leur forme, croissance, cristallisation et durée de vie ? Le complexe magmatique du Torres del Paine représente l'un des meilleurs endroits au monde pour répondre à ces questions. Il se situe au sud de la Patagonie, formant un massif de 70km2. Des réponses peuvent être trouvées à différentes échelles, variant de la montagne à des minéraux de quelques 1000ème de millimètres.Il est possible de distinguer trois types de roches : des gabbros et des diorites sur une épaisseur de 250m, surmontées par des parois de granite de plus de 1000m. Les contacts entre ces roches sont tous horizontaux. Entre granites et gabbro-diorite, le contact est net, indiquant que le second magma s'est mis en place au contact avec un magma plus ancien, totalement solidifié. Entre gabbros et diorites, les contacts sont diffus, souvent non-linéaires, indiquant à l'inverse la mise en contact de magmas encore partiellement liquides. Dans la partie Ouest de cette chambre magmatique, les contacts entre roches sont verticaux. Il s'agit certainement du lieu de remplissage de la chambre magmatique.Lors du refroidissement d'un magma, différents cristaux vont se former. Leur stabilité et leur composition varient en fonction de la pression, de la température ou de la chimie du magma. La séquence de cristallisation peut être définie sur la base d'observations microscopiques et de la composition chimique des minéraux. Différents gabbros sont ainsi distingués : le gabbro à la base est riche en hornblende, d'une taille de ~5mm, sans inclusion de plagioclase mais avec des cristaux d'olivine, clinopyroxene et orthopyroxene inclus ; le gabbro supérieur est lui-aussi riche en hornblende (~5mm), avec les mêmes inclusions additionnées de plagioclase. Ces cristaux se sont formés à une température supérieure à 900°C et une profondeur correspondant à la croûte moyenne ou inférieure. Les minéraux plus fin, se trouvant hors des cristaux de hornblende des deux gabbros, sont similaires à ceux des diorites : plagioclase, biotite, hornblende, apatite, quartz et feldspath alcalin. Ces minéraux sont caractéristiques des granites. Ils ont cristallisé à ~790°C et ~2km de profondeur.La cristallisation des minéraux et leur extraction du magma par gravité provoque un changement progressif de la composition de ce dernier. Ainsi, après extraction d'olivine et d'orthopyroxene riches en Mg, de clinopyroxene riche en Ca, de plagioclase riche en Ca et Al et d'hornblende riche en Ca, Al et Mg, le liquide final sera appauvri en ces élé-ments. Un lien peut ainsi être proposé entre les diorites dont la composition est proche du liquide de départ, les granites dont la composition est similaire au liquide final, et les gabbros dont la minéralogie correspond aux minéraux extraits.L'utilisation de zircons, un minéral riche en U dont les atomes se transforment en Pb par décomposition radioactive au cours de millions d'années, permet de dater le refroidissement des roches qui les contiennent. Ainsi, il a été observé que les roches de la zone d'alimentation, à l'Ouest du complexe magmatique, ont cristallisés il y a 12.59±0.01 Ma, en même temps que les granites les plus vieux, se trouvant au sommet de la chambre magmatique, datés par Michel et al. (2008). Les deux roches pourraient donc avoir la même origine. A l'inverse, les gabbros et diorites de la chambre magmatique ont cristallisé entre 12.47±0.01Ma et 12.43±0.01Ma, les roches les plus vieilles étant à la base.En comparant la composition des roches du Torres del Paine avec celles d'autres en-tités géologiques de Patagonie, les causes du magmatisme peuvent être recherchées. A l'Ouest, on trouve en effet des intrusions granitiques, plus anciennes, caractéristiques de zones de convergence de plaque tectonique, alors qu'à l'Est, des laves basaltiques plus jeunes sont caractéristiques d'une dynamique d'extension. Sur la base des compositions chimiques des roches de ces différentes entités, l'évolution progressive de l'une à l'autre a pu être démontrée. Elle est certainement due à l'arrivée d'une dorsale océanique (zone d'extension crustale et de création de croûte océanique par la remontée de magma) dans la zone de subduction, le long des Andes.Je propose que, dans un premier temps, des magmas granitiques sont remontés dans la chambre magmatique, laissant d'importants volumes de cristaux dans la croûte pro-fonde. Dans un second épisode, les cristaux formés en profondeur ont été transportés à travers la croûte continentale, suite au mélange avec un nouveau magma injecté. Ces magmas chargés de cristaux ont traversé la zone d'alimentation avant de s'injecter dans la chambre magmatique. Différents puises ont été distingués, injectés dans la chambre magmatique du sommet à la base concernant les granites, puis à la base du granite le plus jeune pour les gabbros et diorites. Le complexe magmatique du Torres del Paine s'est construit sur une période totale de 160'000±20'000 ans.

The use of the vac in complex wounds - does it work and how?

Background: Complex wounds pose a major challenge in reconstructive and trauma surgery. Several approaches to increase the healing process have been proposed in the last decades. In this study we study the mechanism of action of the Vacuum Assisted Closure device in diabetic wounds. Methods: Full-thickness wounds were excised in diabetic mice and treated with the VAC device or its isolated components: an occlusive dressing (OD) alone, subathmospheric pressure at 125 mm Hg (Suction), and a polyurethane foam without (Foam) and with (Foamc) downward compression of approximately 125 mm Hg. The last goups were treated with either the complete VAC device (VAC) or with a silicne interface that alows fluid removel (Mepithel-VAC). The effects of the treatment modes on the wound surface were quantified by a two-dimensional immunohistochemical staging system based on vasculature, as defined by blood vessel density (CD31) and cell proliferation (defined by ki67 positivity), 7 days post wounding. Finite element modelling was used to predict wound surface deformation under dressing modes and cross sections of in situ fixed tissues were used to measure actual microstrain. Results: The foam-wound interface of the Vacuum Assisted Closure device causes significant wound stains (60%) causing a deformation of the single cell level leading to a profound upregulation of cell proliferation (4-fold) and angiogenisis (2.2-fold) compared to OD treated wounds. Polyurethane foam exposure itself causes a frather unspecific angiogenic response (Foamc, 2 - fold, Foam, 2.2 - fold) without changes of the cell proliferation rate of the wound bed. Suction alone without a specific interface does not have an effect on meassured parameters, showing similar results to untreated wounds. A perforated silicone interface caused a significant lower microdeforamtion of the wound bed correlating to changes of the wound tissues. Conclusion: The Vacuum Assisted Closure device induce significanttissue growth in diabetic wounds. The wound foam interface under suction causes profound macrodeformation that stimulates tissue growth by angiogenesis and cell proliferation. It needs to be taken in consideration that in the clinical setting different wound types may profit from different elements of this suction device.

Automated formulation of optimisation models for steel beam structures

Over 70% of the total costs of an end product are consequences of decisions that are made during the design process. A search for optimal cross-sections will often have only a marginal effect on the amount of material used if the geometry of a structure is fixed and if the cross-sectional characteristics of its elements are property designed by conventional methods. In recent years, optimalgeometry has become a central area of research in the automated design of structures. It is generally accepted that no single optimisation algorithm is suitable for all engineering design problems. An appropriate algorithm, therefore, mustbe selected individually for each optimisation situation. Modelling is the mosttime consuming phase in the optimisation of steel and metal structures. In thisresearch, the goal was to develop a method and computer program, which reduces the modelling and optimisation time for structural design. The program needed anoptimisation algorithm that is suitable for various engineering design problems. Because Finite Element modelling is commonly used in the design of steel and metal structures, the interaction between a finite element tool and optimisation tool needed a practical solution. The developed method and computer programs were tested with standard optimisation tests and practical design optimisation cases. Three generations of computer programs are developed. The programs combine anoptimisation problem modelling tool and FE-modelling program using three alternate methdos. The modelling and optimisation was demonstrated in the design of a new boom construction and steel structures of flat and ridge roofs. This thesis demonstrates that the most time consuming modelling time is significantly reduced. Modelling errors are reduced and the results are more reliable. A new selection rule for the evolution algorithm, which eliminates the need for constraint weight factors is tested with optimisation cases of the steel structures that include hundreds of constraints. It is seen that the tested algorithm can be used nearly as a black box without parameter settings and penalty factors of the constraints.

Pyörivän keskiökärjen rakenteen kehittäminen työstövärähtelyjen välttämiseksi sorvauksessa

Tässä diplomityössä käsitellään sorvauksen työstövärähtelyjen ja sorvin keskiökärjen rakenteen yhteyttä. Työ on osa Lappeenrannan teknillisen yliopiston VMAX-projektia, ja sen taustalla on pyrkimys uudenlaisen, sorvin kärkipylkän puristusvoiman ajonaikaiseen säätämiseen perustuvan työstövärähtelyjen välttämismenetelmän kehittämiseen. Tämän menetelmän toiminnan todentaminen oli työn ensimmäinen tavoite. Menetelmän toteuttaminen asettaa kuitenkin käytetyn keskiökärjen rakenteelle tiettyjä vaatimuksia. Työn toisena tavoitteena oli nämä vaatimukset täyttävän keskiökärjen prototyypin kehittäminen. Tutkimus eteni seuraavasti. Ensimmäiseksi ongelma määriteltiin tutustumalla työn teoreettiseen taustaan ja aiheeseen liittyvään tutkimukseen Lappeenrannan teknillisestä yliopistosta ja muualta. Myös keskiökärkiä valmistavien yritysten tuotekatalogeja tarkasteltiin. Seuraavaksi siirryttiin alustavaan suunnitteluvaiheeseen, jossa verifioitiin menetelmän toiminta ja luotiin konsepteja keskiökärjen rakenteen kehittämistä varten. Tämän alustavan vaiheen jälkeen suoritettiin suunnitteluprosessi keskiökärjen prototyypille. Lopuksi, suunnitellun prototyypin rakenteen käyttäytymistä arvioitiin tietokonemallinnuksen avulla. Lisätuloksena tutkimuksen aikana johdettiin yksinkertaistettu elementtimenetelmään perustuva laskentamalli järjestelmän ominaistaajuuksien selvittämiseksi. Laskentamallin tarkkuutta arvoitiin. Suunnitteluprosessin tuloksena saatiin kaikki menetelmän toiminnan sekä normaalin käytön asettamat vaatimukset täyttävä rakenne keskiökärjen prototyypille. Myös johdetun laskentamallin tulokset ovat varsin lähellä 3D-elementtimallinnuksen antamia tuloksia. Tutkimuksen tavoitteiden voidaan siis sanoa toteutuneen. Koska prototyyppiä ja laskentamallia ei kuitenkaan ole vielä kokeellisesti verifioitu, tämä ei ole täysin varmaa.