A split-pot experiment with sorghum to test a root water uptake partitioning model

Correct modeling of root water uptake partitioning over depth is an important issue in hydrological and crop growth models. Recently a physically based model to describe root water uptake was developed at single root scale and upscaled to the root system scale considering a homogeneous distribution of roots per soil layer. Root water uptake partitioning is calculated over soil layers or compartments as a function of respective soil hydraulic conditions, specifically the soil matric flux potential, root characteristics and a root system efficiency factor to compensate for within-layer root system heterogeneities. The performance of this model was tested in an experiment performed in two-compartment split-pot lysimeters with sorghum plants. The compartments were submitted to different irrigation cycles resulting in contrasting water contents over time. The root system efficiency factor was determined to be about 0.05. Release of water from roots to soil was predicted and observed on several occasions during the experiment; however, model predictions suggested root water release to occur more often and at a higher rate than observed. This may be due to not considering internal root system resistances, thus overestimating the ease with which roots can act as conductors of water. Excluding these erroneous predictions from the dataset, statistical indices show model performance to be of good quality.

A data-mining based methodology for wind forecasting

In many countries the use of renewable energy is increasing due to the introduction of new energy and environmental policies. Thus, the focus on the efficient integration of renewable energy into electric power systems is becoming extremely important. Several European countries have already achieved high penetration of wind based electricity generation and are gradually evolving towards intensive use of this generation technology. The introduction of wind based generation in power systems poses new challenges for the power system operators. This is mainly due to the variability and uncertainty in weather conditions and, consequently, in the wind based generation. In order to deal with this uncertainty and to improve the power system efficiency, adequate wind forecasting tools must be used. This paper proposes a data-mining-based methodology for very short-term wind forecasting, which is suitable to deal with large real databases. The paper includes a case study based on a real database regarding the last three years of wind speed, and results for wind speed forecasting at 5 minutes intervals.

Computational intelligence applications for future power systems

Power system planning, control and operation require an adequate use of existing resources as to increase system efficiency. The use of optimal solutions in power systems allows huge savings stressing the need of adequate optimization and control methods. These must be able to solve the envisaged optimization problems in time scales compatible with operational requirements. Power systems are complex, uncertain and changing environments that make the use of traditional optimization methodologies impracticable in most real situations. Computational intelligence methods present good characteristics to address this kind of problems and have already proved to be efficient for very diverse power system optimization problems. Evolutionary computation, fuzzy systems, swarm intelligence, artificial immune systems, neural networks, and hybrid approaches are presently seen as the most adequate methodologies to address several planning, control and operation problems in power systems. Future power systems, with intensive use of distributed generation and electricity market liberalization increase power systems complexity and bring huge challenges to the forefront of the power industry. Decentralized intelligence and decision making requires more effective optimization and control techniques techniques so that the involved players can make the most adequate use of existing resources in the new context. The application of computational intelligence methods to deal with several problems of future power systems is presented in this chapter. Four different applications are presented to illustrate the promises of computational intelligence, and illustrate their potentials.

Projecto e concepção de instalação frigorífica a NH3, para uma unidade de congelação de frangos em contínuo, na Venezuela

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Fusão de hospitais em centros hospitalares : impacto no seu desempenho operacional e financeiro

Mestrado em Contabilidade e Análise Financeira

Optimal brake specific fuel consumption trajectory for stand-alone variable speed Diesel Gen-Set

Energy efficiency plays an important role to the CO2 emissions reduction, combating climate change and improving the competitiveness of the economy. The problem presented here is related to the use of stand-alone diesel gen-sets and its high specific fuel consumptions when operates at low loads. The variable speed gen-set concept is explained as an energy-saving solution to improve this system efficiency. This paper details how an optimum fuel consumption trajectory based on experimentally Diesel engine power map is obtained.

A eficácia dos contratos-programa no setor público da saúde na região Norte de Portugal

Em Portugal o sistema de saúde assume uma importante função no desenvolvimento económico e social, na medida em que os serviços prestados pelo mesmo influenciam não só o bem-estar social como também a produtividade. O processo de contratualização alia-se ao setor público da saúde através do contrato-programa, o qual pretende estabelecer uma estratégia a seguir. O presente trabalho pretende verificar se o setor público da saúde respeita os princípios de economia, eficiência e eficácia, de um modo geral, pretende-se perceber se os contratos-programa são cumpridos na sua totalidade. Para tal procedeu-se à recolha da informação descrita nos relatórios de gestão dos quinze Hospitais que pertencem à Administração Regional de Saúde do Norte. A incerteza relacionada com os contratos-programa, a não existência de um modelo linear para a divulgação pública dos resultados no âmbito do contrato-programa, e ainda o facto de a totalidade das entidades não ser obrigada a emitir essa publicação, conduz à possibilidade de que não estejam a ser cumpridos os princípios da economia, eficácia e eficiência.

2011 Road Use Tax Fund (RUTF) Study A report to the Iowa Legislature, per 2011 Iowa Code Section 307.31

The transportation system is in demand 24/7 and 365 days a year irrespective of neither the weather nor the conditions. Iowa’s transportation system is an integral and essential part of society serving commerce and daily functions of all Iowans across the state. A high quality transportation system serves as the artery for economic activity and, the condition of the infrastructure is a key element for our future growth opportunities. A key component of Iowa’s transportation system is the public roadway system owned and maintained by the state, cities and counties. In order to regularly re-evaluate the conditions of Iowa’s public roadway infrastructure and assess the ability of existing revenues to meet the needs of the system, the Iowa Department of Transportation’s 2006 Road Use Tax Fund (RUTF) report to the legislature included a recommendation that a study be conducted every five years. That recommendation was included in legislation adopted in 2007 and signed into law. The law specifically requires the following (2011 Iowa Code Section 307.31): •“The department shall periodically review the current revenue levels of the road use tax fund and the sufficiency of those revenues for the projected construction and maintenance needs of city, county, and state governments in the future. The department shall submit a written report to the general assembly regarding its findings by December 31 every five years, beginning in 2011. The report may include recommendations concerning funding levels needed to support the future mobility and accessibility for users of Iowa's public road system.” •“The department shall evaluate alternative funding sources for road maintenance and construction and report to the general assembly at least every five years on the advantages and disadvantages and the viability of alternative funding mechanisms.” Consistent with this requirement, the Iowa Department of Transportation (DOT) has prepared this study. Recognizing the importance of actively engaging with the public and transportation stakeholders in any discussion of public roadway conditions and needs, Governor Terry E. Branstad announced on March 8, 2011, the creation of, and appointments to, the Governor’s Transportation 2020 Citizen Advisory Commission (CAC). The CAC was tasked with assisting the Iowa DOT as they assess the condition of Iowa’s roadway system and evaluate current and future funding available to best address system needs. In particular the CAC was directed to gather input from the public and stakeholders regarding the condition of Iowa’s public roadway system, the impact of that system, whether additional funding is needed to maintain/improve the system, and, if so, what funding mechanisms ought to be considered. With this input, the CAC prepared a report and recommendations that were presented to Governor Branstad and the Iowa DOT in November 2011 for use in the development of this study. The CAC’s report is available at www.iowadot.gov/transportation2020/pdfs/CAC%20REPORT%20FINAL%20110211.pdf. The CAC’s report was developed utilizing analysis and information from the Iowa DOT. Therefore, the report forms the basis for this study and the two documents are very similar. Iowa is fortunate to have an extensive public roadway system that provides access to all areas of the state and facilitates the efficient movement of goods and people. However, it is also a tremendous challenge for the state, cities and counties to maintain and improve this system given flattening revenue, lost buying power, changing demands on the system, severe weather, and an aging system. This challenge didn’t appear overnight and for the last decade many studies have been completed to look into the situation and the legislature has taken significant action to begin addressing the situation. In addition, the Iowa DOT and Iowa’s cities and counties have worked jointly and independently to increase efficiency and streamline operations. All of these actions have been successful and resulted in significant changes; however, it is apparent much more needs to be done. A well-maintained, high-quality transportation system reduces transportation costs and provides consistent and reliable service. These are all factors that are critical in the evaluation companies undertake when deciding where to expand or locate new developments. The CAC and Iowa DOT heard from many Iowans that additional investment in Iowa’s roadway system is vital to support existing jobs and continued job creation in the state of Iowa. Beginning June 2011, the CAC met regularly to review material and discuss potential recommendations to address Iowa’s roadway funding challenges. This effort included extensive public outreach with meetings held in seven locations across Iowa and through a Transportation 2020 website hosted by the Iowa DOT (www.iowadot.gov/transportation2020). Over 500 people attended the public meetings held through the months of August and September, with 198 providing verbal or written comment at the meetings or through the website. Comments were received from a wide array of individuals. The public comments demonstrated overwhelming support for increased funding for Iowa’s roads. Through the public input process, several guiding principles were established to guide the development of recommendations. Those guiding principles are: • Additional revenues are restricted for road and bridge improvements only, like 95 percent of the current state road revenue is currently. This includes the fuel tax and registration fees. • State and local governments continue to streamline and become more efficient, both individually and by looking for ways to do things collectively. • User fee concept is preserved, where those who use the roads pay for them, including non¬residents. • Revenue-generating methods equitable across users. • Increase revenue generating mechanisms that are viable now but begin to implement and set the stage for longer-term solutions that bring equity and stability to road funding. • Continue Iowa’s long standing tradition of state roadway financing coming from pay-as-you-go financing. Iowa must not fall into the situation that other states are currently facing where the majority of their new program dollars are utilized to pay the debt service of past bonding. Based on the analysis of Iowa’s public roadway needs and revenue and the extensive work of the Governor’s Transportation 2020 Citizen Advisory Commission, the Iowa DOT has identified specific recommendations. The recommendations follow very closely the recommendations of the CAC (CAC recommendations from their report are repeated in Appendix B). Following is a summary of the recommendations which are fully documented beginning on page 21. 1. Through a combination of efficiency savings and increased revenue, a minimum of $215 million of revenue per year should be generated to meet Iowa’s critical roadway needs. 2. The Code of Iowa should be changed to require the study of the sufficiency of the state’s road funds to meet the road system’s needs every two years instead of every five years to coincide with the biennial legislative budget appropriation schedule. 3.Modify the current registration fee for electric vehicles to be based on weight and value using the same formula that applies to most passenger vehicles. 4.Consistent with existing Code of Iowa requirements, new funding should go to the TIME-21 Fund up to the cap ($225 million) and remaining new funding should be distributed consistent with the Road Use Tax Fund distribution formula. 5.The CAC recommended the Iowa DOT at least annually convene meetings with cities and counties to review the operation, maintenance and improvement of Iowa’s public roadway system to identify ways to jointly increase efficiency. In direct response to this recommendation, Governor Branstad directed the Iowa DOT to begin this effort immediately with a target of identifying $50 million of efficiency savings that can be captured from the over $1 billion of state revenue already provided to the Iowa DOT and Iowa’s cities and counties to administer, maintain and improve Iowa’s public roadway system. This would build upon past joint and individual actions that have reduced administrative costs and resulted in increased funding for improvement of Iowa’s public roadway system. Efficiency actions should be quantified, measured and reported to the public on a regular basis. 6.By June 30, 2012, Iowa DOT should complete a study of vehicles and equipment that use Iowa’s public roadway system but pay no user fees or substantially lower user fees than other vehicles and equipment.

Ranking RegionalInnovation Policies: DEA-based Benchmarking in an European Setting

Seudullinen innovaatio on monimutkainen ilmiö, joka usein sijaitsee paikallisten toimijoiden keskinäisen vuorovaikutuksen kentässä. Täten sitä on perinteisesti pidetty vaikeasti mitattavana ilmiönä. Työssä sovellettiin Data Envelopment Analysis menetelmää, joka on osoittautunut aiemmin menestyksekkääksi tapauksissa, joissa mitattavien syötteiden ja tuotteiden väliset suhteet eivät ole olleet ilmeisiä. Työssä luotiin konseptuaalinen malli seudullisen innovaation syötteistä ja tuotteista, jonka perusteella valittiin 12 tilastollisen muuttujan mittaristo. Käyttäen Eurostat:ia datalähteenä, lähdedata kahdeksaan muuttujsta saatiin seudullisella tasolla, sekä mittaristoa täydennettiin yhdellä kansallisella muuttujalla. Arviointi suoritettiin lopulta 45 eurooppalaiselle seudulle. Tutkimuksen painopiste oli arvioida DEA-menetelmän soveltuvuutta innovaatio-järjestelmän mittaamiseen, sillä menetelmää ei ole aiemmin sovellettu vastaavassa tapauksessa. Ensimmäiset tulokset osoittivat ylipäätään liiallisen korkeita tehok-kuuslukuja. Korjaustoimenpiteitä erottelutarkkuuden parantamiseksi esiteltiin ja sovellettiin, jonka jälkeen saatiin realistisempia tuloksia ja ranking-lista arvioitavista seuduista. DEA-menetelmän todettiin olevan tehokas ja kiinnostava työkalu arviointikäytäntöjen ja innovaatiopolitiikan kehittämiseen, sikäli kun datan saatavuusongelmat saadaan ratkaistua sekä itse mallia tarkennettua.

Ranking Regional Innovation Policies: DEA-based Benchmarking in an European Setting

Seudullinen innovaatio on monimutkainen ilmiö, joka usein sijaitsee paikallisten toimijoiden keskinäisen vuorovaikutuksen kentässä. Täten sitä on perinteisesti pidetty vaikeasti mitattavana ilmiönä. Työssä sovellettiin Data Envelopment Analysis menetelmää, joka on osoittautunut aiemmin menestyksekkääksi tapauksissa, joissa mitattavien syötteiden ja tuotteiden väliset suhteet eivät ole olleet ilmeisiä. Työssä luotiin konseptuaalinen malli seudullisen innovaation syötteistä ja tuotteista, jonka perusteella valittiin 12 tilastollisen muuttujan mittaristo. Käyttäen Eurostat:ia datalähteenä, lähdedata kahdeksaan muuttujsta saatiin seudullisella tasolla, sekä mittaristoa täydennettiin yhdellä kansallisella muuttujalla. Arviointi suoritettiin lopulta 45 eurooppalaiselle seudulle. Tutkimuksen painopiste oli arvioida DEA-menetelmän soveltuvuutta innovaatiojärjestelmän mittaamiseen, sillä menetelmää ei ole aiemmin sovellettu vastaavassa tapauksessa. Ensimmäiset tulokset osoittivat ylipäätään liiallisen korkeita tehokkuuslukuja. Korjaustoimenpiteitä erottelutarkkuuden parantamiseksi esiteltiin ja sovellettiin, jonka jälkeen saatiin realistisempia tuloksia ja ranking-lista arvioitavista seuduista. DEA-menetelmän todettiin olevan tehokas ja kiinnostava työkalu arviointikäytäntöjen ja innovaatiopolitiikan kehittämiseen, sikäli kun datan saatavuusongelmat saadaan ratkaistua sekä itse mallia tarkennettua.

Automatització de l’estació FESTO MPS2000C

L’Escola Politècnica Superior de la Universitat de Vic disposa d’una cèl·lula de fabricació didàctica de la marca FESTO que simula un procés d’assemblatge d’una comanda. Aquesta cèl·lula esta composta per quatre estacions diferenciades que poden treballar de forma independent o de forma conjunta, l’estació palets, l’estació plaques, l’estació cinta i l’estació magatzem. Cada estació és un conjunt de sensors i actuadors controlats per mitjà d’un PLC, aquests estan interconnectats a través d’un bus industrial. L’objectiu d’aquest treball consisteix en realitzar la substitució dels PLC’s, decidir el funcionament que han de tenir les estacions, instal·lar una pantalla tàctil pel control del procés i realitzar la programació de tots els elements. Aquest projecte ha estat realitzat en cinc fases principals: 1. Estudi i coneixement de les estacions, en aquesta fase s’ha estudiat els diferents sensors i actuadors que les conformen, així com el funcionament d’aquestes amb el programa i PLC’s antics. 2. Instal·lació i cablejat dels nous PLC’s i de la pantalla tàctil. 3. Estudi sobre el nou funcionament que han de seguir les estacions. 4. Programació dels nous dispositius seguint el funcionament acordat. 5. Posada en marxa del sistema i realització de proves. 6. Realització de la memòria del projecte, on s’expliquen les característiques i el funcionament de totes les estacions i de la pantalla tàctil. La conclusió que s’ha extret d’aquest treball és que l’automatització d’un procés de fabricació tot i que suposa un esforç inicial a nivell de recursos, un cop realitzada la instal·lació suposa una millora de l’eficiència del sistema. És per això que la indústria cada cop més tendeix a automatitzar els seus processos, no només per millorar la competitivitat, sinó també per realitzar tasques que les persones no poden executar de forma eficient o segura.

Influence of EfOM on the oxidation of micropollutants by Ozone and UV/H2O2 in secondary effluents

The aim of this work was to study the influence of effluent organic matter (EfOM) on micropollutants removal by ozone and UV/H2O2. To perform the experiments, deionized water and municipal secondary effluents (SE) were artificially contaminated with atrazine (ATZ) and treated by the two proposed methods. ATZ concentration, COD and TOC were recorded along the reaction time and used to evaluate EfOM effect on the system efficiency. Results demonstrate that the presence of EfOM can significantly reduce the micropollutant removal rate due to competition of EfOM components to react with radicals and/or molecular ozone. The hydroxyl radical scavenging caused by EfOM was quantified as well as the contribution of molecular ozone and �OH radicals during the ozonation of SE. EfOM components promoted higher inhibition of ATZ oxidation by hydroxyl radicals than by molecular ozone.

Benefits of automated acclimatization during the pre-milking phase of lactating girolando cows

The aim of this paper was to evaluate the automated acclimatization effects during pre-milking of cows on thermal conditioning, physiology, milk production and cost-benefit of the automated adiabatic evaporative cooling system (AECS). The treatments 20; 30; 40 min and control consisted of exposure time of pre-milking cows to the automated AECS. Sixteen cows were used with an average daily milk yield of 19 kg, distributed in a 4 x 4 Latin square design. The Tukey's test (P<0.05) was used to compare the means. The environmental variables, dry bulb temperature (DBT, ºC) and relative humidity (RH, %), were recorded every minute, which allowed the determination of the system efficiency through the Temperature and Humidity Index (THI). The respiratory rate (RR), rectal temperature (RT) and temperature of the coat (TC) were measured before and after the acclimatization. The 40 min treatment kept the environmental variables and the comfort indexes within recommended limits. The physiological variables (RR, RT and TC) were lower in the 40 min treatment and reflected positively on milk production, which increased 3.66% compared to the control treatment. The system was profitable, having a 43 days return on investment and a monthly revenue increase of R$ 1,992.67.

Preventive diagnosis of dairy cow lameness

This research aimed to develop a Fuzzy inference based on expert system to help preventing lameness in dairy cattle. Hoof length, nutritional parameters and floor material properties (roughness) were used to build the Fuzzy inference system. The expert system architecture was defined using Unified Modelling Language (UML). Data were collected in a commercial dairy herd using two different subgroups (H1 and H2), in order to validate the Fuzzy inference functions. The numbers of True Positive (TP), False Positive (FP), True Negative (TN), and False Negative (FN) responses were used to build the classifier system up, after an established gold standard comparison. A Lesion Incidence Possibility (LIP) developed function indicates the chances of a cow becoming lame. The obtained lameness percentage in H1 and H2 was 8.40% and 1.77%, respectively. The system estimated a Lesion Incidence Possibility (LIP) of 5.00% and 2.00% in H1 and H2, respectively. The system simulation presented 3.40% difference from real cattle lameness data for H1, while for H2, it was 0.23%; indicating the system efficiency in decision-making.

Design and Material Selection of High-Speed Rotating Electrical Machines

The increasing emphasis on energy efficiency is starting to yield results in the reduction in greenhouse gas emissions; however, the effort is still far from sufficient. Therefore, new technical solutions that will enhance the efficiency of power generation systems are required to maintain the sustainable growth rate, without spoiling the environment. A reduction in greenhouse gas emissions is only possible with new low-carbon technologies, which enable high efficiencies. The role of the rotating electrical machine development is significant in the reduction of global emissions. A high proportion of the produced and consumed electrical energy is related to electrical machines. One of the technical solutions that enables high system efficiency on both the energy production and consumption sides is high-speed electrical machines. This type of electrical machines has a high system overall efficiency, a small footprint, and a high power density compared with conventional machines. Therefore, high-speed electrical machines are favoured by the manufacturers producing, for example, microturbines, compressors, gas compression applications, and air blowers. High-speed machine technology is challenging from the design point of view, and a lot of research is in progress both in academia and industry regarding the solution development. The solid technical basis is of importance in order to make an impact in the industry considering the climate change. This work describes the multidisciplinary design principles and material development in high-speed electrical machines. First, high-speed permanent magnet synchronous machines with six slots, two poles, and tooth-coil windings are discussed in this doctoral dissertation. These machines have unique features, which help in solving rotordynamic problems and reducing the manufacturing costs. Second, the materials for the high-speed machines are discussed in this work. The materials are among the key limiting factors in electrical machines, and to overcome this limit, an in-depth analysis of the material properties and behavior is required. Moreover, high-speed machines are sometimes operating in a harsh environment because they need to be as close as possible to the rotating tool and fully exploit their advantages. This sets extra requirements for the materials applied.