Characterization of CPV arrays based on differences on their thermal resistances

Thermal characterization of Concentrating Photovoltaics (CPV) modules and Arrays is needed to determine their performance and modelling of energy forecast. Module-ambient thermal resistance is easily obtained from its definition but the cell-module thermal resistant needs to be estimated from indirect procedures, two of them are presented in this paper. In addition, an equivalent parameter is defined, the Concentrator Nominal Operating Module/Cell Temperature (CNOMT/CNOCT), the temperature at Concentrator Standard Operating Conditions (CSOC). Definitions and expression to relate (CNOMT/CNOCT) to thermal resistances are presented, plus several examples of estimations from real operating arrays.

Experimental study of the thermal-energy performance of an insulated vegetal facade under summer conditions in a continental mediterranean climate

The use of vegetal systems in facades affects the reduction of the buildings' energy demand, the attenuation of the urban heat island (UHI) and the filtration of pollutants present in the air. Even so, up to now the knowledge about the effect of this type of systems on the thermal performance of insulated facades is limited. This article presents the results of an experimental study carried out in a vegetal facade located in a continental Mediterranean climate zone. The objective is to study the effect of a vegetal finishing, formed by plants and substrate, on the thermal-energy performance of an insulated facade under summer conditions. To this effect, the thermal data obtained from two full-scale experimental mock-ups of the same dimensions and composition of the enclosure and only different in the south facade's enclosure where one incorporates a vegetation layer are compared and analysed. The results show that, in spite of the high thermal resistance of the enclosure, the effect of the vegetation is very positive, particularly in the warmer hours of the day. Therefore, vegetal facades can be used as a passive cooling strategy, reducing the consumption of energy for refrigeration and improving the comfort conditions of the users. (C) 2014 Elsevier Ltd. All rights reserved.

(Table 1) Thermal conductivities of lithified core samples from ODP Leg 166 sites

The geothermal regime of the western margin of the Great Bahama Bank was examined using the bottom hole temperature and thermal conductivity measurements obtained during and after Ocean Drilling Program (ODP) Leg 166. This study focuses on the data from the drilling transect of Sites 1003 through 1007. These data reveal two important observational characteristics. First, temperature vs. cumulative thermal resistance profiles from all the drill sites show significant curvature in the depth range of 40 to 100 mbsf. They tend to be of concave-upward shape. Second, the conductive background heat-flow values for these five drill sites, determined from deep, linear parts of the geothermal profiles, show a systematic variation along the drilling transect. Heat flow is 43-45 mW/m**2 on the seafloor away from the bank and decreases upslope to ~35 mW/m**2. We examine three mechanisms as potential causes for the curved geothermal profiles. They are: (1) a recent increase in sedimentation rate, (2) influx of seawater into shallow sediments, and (3) temporal fluctuation of the bottom water temperature (BWT). Our analysis shows that the first mechanism is negligible. The second mechanism may explain the data from Sites 1004 and 1005. The temperature profile of Site 1006 is most easily explained by the third mechanism. We reconstruct the history of BWT at this site by solving the inverse heat conduction problem. The inversion result indicates gradual warming throughout this century by ~1°C and is agreeable to other hydrographic and climatic data from the western subtropic Atlantic. However, data from Sites 1003 and 1007 do not seem to show such trends. Therefore, none of the three mechanisms tested here explain the observations from all the drill sites. As for the lateral variation of the background heat flow along the drill transect, we believe that much of it is caused by the thermal effect of the topographic variation. We model this effect by obtaining a two-dimensional analytical solution. The model suggests that the background heat flow of this area is ~43 mW/m**2, a value similar to the background heat flow determined for the Gulf of Mexico in the opposite side of the Florida carbonate platform.

Multiobjective design optimization of IGBT power modules considering power cycling and thermal cycling

Insulated-gate bipolar transistor (IGBT) power modules find widespread use in numerous power conversion applications where their reliability is of significant concern. Standard IGBT modules are fabricated for general-purpose applications while little has been designed for bespoke applications. However, conventional design of IGBTs can be improved by the multiobjective optimization technique. This paper proposes a novel design method to consider die-attachment solder failures induced by short power cycling and baseplate solder fatigue induced by the thermal cycling which are among major failure mechanisms of IGBTs. Thermal resistance is calculated analytically and the plastic work design is obtained with a high-fidelity finite-element model, which has been validated experimentally. The objective of minimizing the plastic work and constrain functions is formulated by the surrogate model. The nondominated sorting genetic algorithm-II is used to search for the Pareto-optimal solutions and the best design. The result of this combination generates an effective approach to optimize the physical structure of power electronic modules, taking account of historical environmental and operational conditions in the field.

Real-time temperature estimation for power MOSFETs considering thermal ageing effects

This paper presents a novel real-time power-device temperature estimation method that monitors the power MOSFET's junction temperature shift arising from thermal aging effects and incorporates the updated electrothermal models of power modules into digital controllers. Currently, the real-time estimator is emerging as an important tool for active control of device junction temperature as well as online health monitoring for power electronic systems, but its thermal model fails to address the device's ongoing degradation. Because of a mismatch of coefficients of thermal expansion between layers of power devices, repetitive thermal cycling will cause cracks, voids, and even delamination within the device components, particularly in the solder and thermal grease layers. Consequently, the thermal resistance of power devices will increase, making it possible to use thermal resistance (and junction temperature) as key indicators for condition monitoring and control purposes. In this paper, the predicted device temperature via threshold voltage measurements is compared with the real-time estimated ones, and the difference is attributed to the aging of the device. The thermal models in digital controllers are frequently updated to correct the shift caused by thermal aging effects. Experimental results on three power MOSFETs confirm that the proposed methodologies are effective to incorporate the thermal aging effects in the power-device temperature estimator with good accuracy. The developed adaptive technologies can be applied to other power devices such as IGBTs and SiC MOSFETs, and have significant economic implications.

Embedded heat pipes in cofired ceramic substrates for enhanced thermal management of electronics

A novel and new thermal management technology for advanced ceramic microelectronic packages has been developed incorporating miniature heat pipes embedded in the ceramic substrate. The heat pipes use an axially grooved wick structure and water as the working fluid. Prototype substrate/heat pipe systems were fabricated using high temperature co-fired ceramic (alumina). The heat pipes were nominally 81 mm in length, 10 mm in width, and 4 mm in height, and were charged with approximately 50–80 μL of water. Platinum thick film heaters were fabricated on the surface of the substrate to simulate heat dissipating electronic components. Several thermocouples were affixed to the substrate to monitor temperature. One end of the substrate was affixed to a heat sink maintained at constant temperature. The prototypes were tested and shown to successful and reliably operate with thermal loads over 20 Watts, with thermal input from single and multiple sources along the surface of the substrate. Temperature distributions are discussed for the various configurations and the effective thermal resistance of the substrate/heat pipe system is calculated. Finite element analysis was used to support the experimental findings and better understand the sources of the system's thermal resistance. ^

Embedded Heat Pipes in Cofired Ceramic Substrates for Enhanced Thermal Management of Electronics

A novel and new thermal management technology for advanced ceramic microelectronic packages has been developed incorporating miniature heat pipes embedded in the ceramic substrate. The heat pipes use an axially grooved wick structure and water as the working fluid. Prototype substrate/heat pipe systems were fabricated using high temperature co-fired ceramic (alumina). The heat pipes were nominally 81 mm in length, 10 mm in width, and 4 mm in height, and were charged with approximately 50-80 mL of water. Platinum thick film heaters were fabricated on the surface of the substrate to simulate heat dissipating electronic components. Several thermocouples were affixed to the substrate to monitor temperature. One end of the substrate was affixed to a heat sink maintained at constant temperature. The prototypes were tested and shown to successful and reliably operate with thermal loads over 20 Watts, with thermal input from single and multiple sources along the surface of the substrate. Temperature distributions are discussed for the various configurations and the effective thermal resistance of the substrate/heat pipe system is calculated. Finite element analysis was used to support the experimental findings and better understand the sources of the system's thermal resistance.

Densificação e microestrutura de um compósito Mo-Cu preparado a partir de um pó de heptamolibidato de amônia e cobre

The Cu-Mo system is a composite used in the electrical industry as material for electrical contact and resistance welding electrode as well as the heat sink and microwave absorber in microelectronic devices. The use of this material in such applications is due to the excellent properties of thermal and electrical conductivity and the possibility of adjustment of its coefficient of thermal expansion to meet those of materials used as substrates in the semiconductor micoreletrônic industry. Powder metallurgy through the processes of milling, pressing shaping and sintering is a viable technique for consolidation of such material. However, the mutual insolubility of both phases and the low wettability of liquid Cu on Mo impede its densification. However, the mutual insolubility of both phases and the low wettability of liquid Cu on Mo impede its densification. The mechanical alloying is a technique for preparation of powders used to produce nanocrystalline composite powder with amorphous phase or extended solid solution, which increases the sinterability immiscible systems such as the Mo-Cu. This paper investigates the influence of ammonium heptamolybdate (HMA) and the mechanical alloying in the preparation of a composite powder HMA-20% Cu and the effect of this preparation on densification and structure of MoCu composite produced. HMA and Cu powders in the proportion of 20% by weight of Cu were prepared by the techniques of mechanical mixing and mechanical alloying in a planetary mill. These were milled for 50 hours. To observe the evolution of the characteristics of the particles, powder samples were taken after 2, 10, 15, 20, 30 and 40 hours of milling. Cylindrical samples 5 to 8 mm in diameter and 3 to 4 mm thickness were obtained by pressing at 200 MPa to the mixed powders so as to ground. These samples were sintered at 1200 ° C for 60 minutes under an atmosphere of H2. To determine the effect of heating rate on the structure of the material during the decomposition and reduction of HMA, rates of 2, 5 and 10 ° C / min were used .. The post and the structures of the sintered samples were characterized by SEM and EDS. The density of the green and sintered bodies was measured using the geometric method (weight / volume). Vickers microhardness with a load of 1 N for 15 s were performed on sintered structures. The density of the sintered structures 10 ° C / min. reached 99% of theoretical density, how the density of sintered structures to 2 ° C / min. reached only 90% of the theoretical density

Underground power cable environment on-line monitoring and analysis

Knowledge of cable parameters has been well established but a better knowledge of the environment in which the cables are buried lags behind. Research in Queensland University of Technology has been aimed at obtaining and analysing actual daily field values of thermal resistivity and diffusivity of the soil around power cables. On-line monitoring systems have been developed and installed with a data logger system and buried spheres that use an improved technique to measure thermal resistivity and diffusivity over a short period. Results based on long term continuous field data are given. A probabilistic approach is developed to establish the correlation between the measured field thermal resistivity values and rainfall data from weather bureau records. This data from field studies can reduce the risk in cable rating decisions and provide a basis for reliable prediction of “hot spot” of an existing cable circuit

Exploiting the facile oxidation of evaporated gold films to drive electroless silver deposition for the creation of bimetallic Au/Ag surfaces

Gold is often considered as an inert material but it has been unequivocally demonstrated that it possesses unique electronic, optical, catalytic and electrocatalytic properties when in a nanostructured form.[1] For the latter the electrochemical behaviour of gold in aqueous media has been widely studied on a plethora of gold samples, including bulk polycrystalline and single-crystal electrodes, nanoparticles, evaporated films as well as electrodeposited nanostructures, particles and thin films.[1b, 2] It is now well-established that the electrochemical behaviour of gold is not as simple as an extended double-layer charging region followed by a monolayer oxide-formation/-removal process. In fact the so-called double-layer region of gold is significantly more complicated and has been investigated with a variety of electrochemical and surface science techniques. Burke and others[3] have demonstrated that significant processes due to the oxidation of low lattice stabilised atoms or clusters of atoms occur in this region at thermally and electrochemically treated electrodes which were confirmed later by Bond[4] to be Faradaic in nature via large-amplitude Fourier transformed ac voltammetric experiments. Supporting evidence for the oxidation of gold in the double-layer region was provided by Bard,[5] who used a surface interrogation mode of scanning electrochemical microscopy to quantify the extent of this process that forms incipient oxides on the surface. These were estimated to be as high as 20% of a monolayer. This correlated with contact electrode resistance measurements,[6] capacitance measurements[7] and also electroreflection techniques...

Theoretical Maximum Limits on Power-Handling Capacity of HVDC Cables

In the case of an ac cable, power transmission is limited by the length of the cable due to the capacitive reactive current component. It is well known that high-voltage direct current (HVDC) cables do not have such limitations. However, insulation-related thermal problems pose a limitation on the power capability of HVDC cables. The author presents a viable theoretical development, a logical extension to Whitehead's theory on thermal limitations of the insulation. The computation of the maximum power-carrying capability of HVDC cables subject to limits on the maximum operable temperature of the insulation is presented. The limitation on the power-carrying capability is closely associated with the electrothermal insulation failure. The effect of environmental interaction by way of external thermal resistance, an important aspect, is also considered in the formulations. The Lagrange multiplier method has been used to handle the ensuing optimization problem. The theory is based on an accepted theory of thermal breakdown in insulation and is an important and a coherent extension of great significance.

Avaliação das propriedades de barreira a gases de membranas obtidas a partir de dispersões aquosas à base de poliuretanos e argila

Materiais nanoestruturados têm recebido destaque na comunidade científica, destacando-se, dentre eles, os nanocompósitos à base de polímeros e argila. Quando esses materiais são obtidos no estado líquido, ressalta-se também o uso de água em substituição a solventes orgânicos, devido a questões ambientais. Neste trabalho foram sintetizadas dispersões aquosas à base de poliuretanos (WPUs) e argila hidrofílica do tipo montimorilonita (MMT) de natureza sódica, com o objetivo de avaliar as propriedades de barreira a gases conferidas pela presença de argila e pela variação nas proporções entre os segmentos flexíveis poli(glicol propilênico) (PPG) e o copolímero em bloco à base de poli(glicol etilênico) e poli(glicol propilênico) (EG-b-PG). Os monômeros empregados na síntese foram: poli(glicol propilênico) (PPG); copolímero em bloco à base de poli(glicol etilênico) e poli(glicol propilênico) (EG-b-PG), com teor de 7% de EG; ácido dimetilolpropiônico (DMPA), diisocianato de isoforona (IPDI) e etilenodiamina (EDA), como extensor de cadeia. Foram sintetizadas dispersões aquosas com e sem a presença de argila, fixando-se a razão entre o número de equivalentes-grama de grupos diisocianato e hidroxila (razão NCO/OH) em 1,5. Nas formulações foi variado também o teor de argila em relação à massa de prepolímero em 0,5% e 1%. Foi adicionada uma etapa de agitação adicional com dispersor Turrax em algumas formulações. A argila foi previamente deslaminada em água deionizada e incorporada à formulação na etapa da dispersão do prepolímero. As dispersões foram avaliadas, quanto ao teor de sólidos totais, tamanho médio de partícula e viscosidade aparente. Os filmes vazados a partir das dispersões foram caracterizados por espectrometria na região do infravermelho (FTIR) e permeabilidade ao CO2. A resistência térmica dos filmes foi determinada por termogravimetria (TG). Foram observadas modificações nas propriedades dos filmes obtidos com a inserção da argila e com a variação no teor de segmentos à base de poli(glicol etilênico). A inserção da argila promoveu uma melhoria na resistência térmica das membranas bem como uma redução na permeabilidade das mesmas. Foi observado um aumento na permeabilidade das membranas obtidas a partir das formulações com maior percentual de copolímero (EG-b-PG), com e sem argila.

高硅氧发光玻璃的制备及其荧光性能

abstract {Silica glass is an attractive host matrix for the emission ions of rare earth and transition metal ions because it has small thermal expansion coefficient, strong thermal resistance, large fracture strength and good chemical durability and so on. However, a major obstacle to using it as the host matrix is a phenomenon of concentration quenching. In this paper, we introduces a novel method to restrain the concentration quenching by using a porous glass with SiO₂ content > 95% (in mass) and prepare intense fluorescence high-SiO₂ glasses and high-SiO₂ laser glass. The porous glass with high-SiO₂ content was impregnated with rare-earth and transition metal ions, and consequently sintered into a compact non-porous glass in reduction or oxidization atmospheres. Various intense fluorescence glasses with high emission yields, a vacuum ultraviolet-excited intensely luminescent glass, high silica glass containing high concentration of Er³⁺ ion, ultrabroad infrared luminescent Bi-doped high silica glass and Nd³⁺-doped silica microchip laser glass were obtained by this method. The porous glass is also favorable for co-impregnating multi-active-ions. It can bring effective energy transferring between various active ions in the glass and increases luminescent intensity and extend range of excitation spectrum. The luminescent active ions-doped high-SiO₂ glasses are potential host materials for high power solid-state lasers and new transparent fluorescence materials.}

Preparação e caracterização de microesferas poliméricas à base de poli(ácido metacrílico-co-divinilbenzeno) obtidas por polimerização por precipitação

Neste trabalho foi feito um estudo sobre a preparação e caracterização de microesferas poliméricas à base de poli(ácido metacrílico-co-divinilbenzeno) por polimerização por precipitação. As partículas foram sintetizadas e analisadas em diferentes condições de reação. Partículas esféricas políméricas foram sintetizadas na faixa de 1,66 - 8,41 m, assim como partículas no estado de microgel. As partículas foram caracterizadas pelas técnicas de espalhamento de luz dinâmica (DLS), análise termogravimétrica (TGA), espectroscopia na região do infravermelho (FTIR), adsorção de nitrogênio pelos métodos BET (Brunauer, Emmett e Teller) e BJH (Barret, Joyner e Halenda), microscopia ótica, microscopia eletrônica de varredura, e testes de razão de inchamento. A análise das partículas foi feita para verificar a influência da mudança na composição de comonômeros, grau de reticulação, relação de monômeros totais/diluentes em massa/volume (g/100 mL), e quanto à relação volumétrica de diluentes. Verificou-se que houve um aumento no tamanho das partículas e da resistência térmica com a diminuição da fração molar de MAA (ácido metacrílico). Na preparação de partículas com fração molar de 50% de MAA, e relação volumétrica acetonitrila/tolueno de 75/25, quanto maior a relação de monômeros totais/diluentes (g/100 mL), maior o tamanho e o rendimento das partículas. Com a mudança da relação volumétrica de diluentes, houve mudança nas características de porosidade, tamanho das partículas, e grau de inchamento das partículas, sendo que na relação volumétrica acetonitrila/tolueno de 50/50, houve formação de microgel

Preparação e avaliação de hidrogéis nanocompósitos à base de alginato na remoção de Cu (II) e Zn (II) de soluções aquosas

Esta dissertação teve como objetivo, a preparação de hidrogéis à base de alginato contendo argila e material magnético em sua estrutura. Foram analisadas as modificações nas características físico-químicas dos hidrogéis preparados com diferentes reticulantes (CaCl2 e FeCl3) e diferentes concentrações de material magnético (1 e 3 % m/m) e argila (1, 5 e 10 %). Após isso, os hidrogéis foram avaliados quanto à capacidade de remoção de íons Cu2+ e Zn2+ de soluções aquosas. As amostras foram caracterizadas quanto à composição química por espectroscopia na região do infravermelho (FTIR), quanto à morfologia por microscopia óptica e microscopia eletrônica de varredura (SEM) e quanto às propriedades magnéticas por magnetometria de amostra vibrante (VSM). Através da técnica de difratometria de raios-X (XRD), foi possível verificar a natureza do material magnético e a dispersão da argila nos hidrogéis. A estabilidade térmica das amostras foi analisada por análise termogravimétrica (TGA). Os resultados mostraram que tanto a argila como o material magnético ficaram bem dispersos nas amostras. De forma geral, foram preparados hidrogéis com morfologia esférica, sendo que os hidrogéis de alginato de cálcio tenderam a apresentar maior resistência térmica do que os hidrogéis de alginato de ferro. Todas as amostras magnéticas apresentaram comportamento superparamagnético, porém as amostras de alginato de ferro mostraram-se quebradiças após o intumescimento em água. O tempo médio de equilíbrio de intumescimento foi de 240 minutos. Os resultados de cinética de adsorção mostraram que os hidrogéis de alginato de cálcio preparados nas condições avaliadas nesta Dissertação foram eficientes na remoção dos íons Cu2+ e Zn2+, sendo que o cobre apresentou maior afinidade pelo hidrogel do que o zinco