Nutrient loss in composting of agroindustrial residues

The management of composting may influence the characteristics of the produced compounds. The experiment used three frequencies of plowing, combined with the conditions: with and without coverage of the composting patio, with and without the use of commercial inoculant, resulting in 12 furrows, installed on the Experimental Center of Agricultural Engineering (NEEA), of the STATE UNIVERSITY OF WEST PARANÁ (UNIOESTE), Campus of Cascavel city - state of Paraná (PR), in Brazil. The waste and quantities used in kg were: corn cob (7.5); hatchery residue (5); floater sludge (31); ash (1); wheat cleaning residue (120); wheat pre-cleaning residue (120); corn peel (7.5); solid fraction of wash trucks used to transport chickens (2); solid fraction of pig manure (1) and coal (5), totaling 300kg of natural matter. The aim of this study was to evaluate the influence of plowings, patio coverage and inoculation in losses of N, P, K, Ca, Mg, Na, Cu, Zn, Mn, Fe. The furrows plowed three times a week in the first month showed significant higher losses of N (p<0.05). The coverage of the composting patio influenced significantly the losses of N, K, Mg and Na (p<0.05). The produced compounds had a high agronomic value in relation to macro and micronutrients. It is recommended the use of patio coverage and plowing twice a week in the first month and once a week in the subsequent months for a compound with higher concentrations of nutrients.

Weed interference on growth and yield of transgenic maize

Plants kept under competition tend to modify their morphology to optimize the use of production factors. This study aimed to evaluate the effects of competition between transgenic maize and five weed species on the growth and yield of transgenic maize hybrid. The experiment used a randomized block design with four replicates in a factorial 5 x 2 + 6 scheme consisting of a combination of maize under competition with five weed species (Bidens pilosa, Commelina benghalensis, Brachiaria brizantha, Sorghum arundinaceum and Ipomoea triloba) in two weed densities (15 or 30 plants m-2) plus six treatments corresponding to maize and weed species without competition. All the means for dry matter accumulated by maize plants in the stem and leaf in the density of 15 plants m ² were higher than the means for plants in coexistence with 30 plants m-². Number of kernels, diameter and length of cob were not affected by competition with weeds. The weeds that most interfered with maize biomass production were S.arundinaceum and B.brizantha. Leaf dry mass accumulation was more sensitive than the production of stem. It was observed that maize was usually very competitive with weeds, and there was a strong decrease in dry matter accumulation of all the weeds in the study when in coexistence with the crop.

GROWTH AND YIELD RESPONSE OF MAIZE (Zea mays) TO INTER AND INTRA-ROW WEED COMPETITION UNDER DIFFERENT FERTILIZER APPLICATION METHODS

A field experiment was conducted for two consecutive years to study the effect of fertilizer application methods and inter and intra-row weed-crop competition durations on density and biomass of different weeds and growth, grain yield and yield components of maize. The experimental treatments comprised of two fertilizer application methods (side placement and below seed placement) and inter and intra-row weed-crop competition durations each for 15, 30, 45, and 60 days after emergence, as well as through the crop growing period. Fertilizer application method didn't affect weed density, biomass, and grain yield of maize. Below seed fertilizer placement generally resulted in less mean weed dry weight and more crop leaf area index, growth rate, grain weight per cob and 1000 grain weight. Minimum number of weeds and dry weight were recorded in inter-row or intra-row weed-crop competition for 15 DAE. Number of cobs per plant, grain weight per cob, 1000 grain weight and grain yield decreased with an increase in both inter-row and intra-row weed-crop competition durations. Maximum mean grain yield of 6.35 and 6.33 tha-1 were recorded in inter-row and intra-row weed competition for 15 DAE, respectively.

Home Made Cars: An insight on Consumer Ethnocentrism – Case Saab

Saab outstands in the history of the Finnish car manufacturing. This is not only due to that these cars have been manufactured in Finland more than other passenger vehicles altogether. Finns also have a special emotional attachment to the “Finnish Saabs”. Findings from previous studies show that consumers connect cars well to the origin of the brand (COB). They are however rarely aware of the Country of Manufacturing (COM). Domestic brands are often popular in the COB, but research from situations in which the domestic origin is limited to the COM is rare. The case of this study is a phenomenon, in which the products origin is two dimensional and divided into domestic COM and foreign COB. The aim is to understand the phenomenon’s effect on consumer behavior. The research problem is approached with two sub questions: • Which country do consumers perceive as the origin country of the car? • What is the role of this origin in the consumers’ product perception and purchasing decision of the car? The theoretical framework of this study applies previous findings of two areas of interest: Country of Origin effect and Consumer Ethnocentrism. This is followed by feasibility studies that present and discuss the history and current state of Finnish car manufacturing. Based on the findings of earlier stages of the study, the role of the domestic COM on consumer behavior is presumed high. This expectation is confirmed by the experts and also by the first consumer respondent, who states domestic origin having been the main motivation to his car choice. All further consumer respondents do however not connect Saab to the home country, but discuss it as a Nordic car. This unexpected finding means that they do not perceive the origin to be neither the COM nor COB, but a geographical area that includes both countries. In other words, consumers have widened their in-group in a way that is in this thesis explained with reference group theory. The consumers’ perceived origin of the car is in this research found to be an important factor to the consumers’ product perception and purchasing decision. Being fit for the yields of the local environment is discovered to have been the most important factor to Finnish consumers purchasing choice of a Saab and the Nordic origin has been an indicator of this fit to them.

Cuadrados mágicos, instrumentos de cálculo. Primera parte.

Este trabajo, fruto de una investigación matemática didáctica realizada durante los años 1995 a 1997 por un grupo de maestros de escuela y profesores de Bachillerato, trabaja sobre la deducción de la fórmula para cuadrados mágicos de 4x4 y otros mayores y también su aplicación a la enseñanza y práctica de las operaciones matemáticas básicas. El objetivo es dar a conocer los cuadrados mágicos y los procedimientos de su obtención así como las posibilidades didácticas que encierran para la práctica del cálculo numérico en la clase. Contiene una serie de fichas ilustradas de diferentes niveles de dificultad y un disquete de 3 1/2 (EXCEL 5.0 y WORD 6.0). Este trabajo no está publicado.

El Cubo de la Ciencia.

Resumen tomado de la publicación

Guía práctica de acceso a la información en la biblioteca escolar : de la pregunta al documento.

Resumen basado en el de la publicación

Atividades Biológicas De Xilana De Sabugo De Milho

The corn cob is an agricultural by-product still little used, this in part due to the low knowledge of the biotechnological potential of their molecules. Xylan from corn cobs (XSM) is a polysaccharide present in greater quantity in the structure of plant and its biotechnology potential is little known. This study aimed to the extraction, chemical characterization and evaluation of biological activities of xylan from corn cobs. To this end, corncobs were cleaned, cut, dried and crushed, resulting in flour. This was subjected to a methodology that combines the use of alkaline conditions with waves of ultrasound. After methanol precipitation, centrifugation and drying was obtained a yield of 40% (g/g flour). Chemical analysis indicated a high percentage of polysaccharides in the sample (60%) and low contamination by protein (0.4%) and phenolic compounds (> 0.01%). Analysis of monosaccharide composition indicated the presence of xylose:glucose:arabinose:galactose:mannose:glucuronic acid in a molar ratio 50:20:15:10:2.5:2.5. The presence of xylan in the sample was confirmed by nuclear magnetic resonance (¹H and ¹³C) and infrared spectroscopy (IR). Tests were conducted to evaluate the antioxidant potential of XSM. This showed a total antioxidant capacity of 48.45 EAA/g sample. However, did not show scavenging activity of superoxide and hydroxyl radical and also reducing power. But, showing a high capacity chelating iron ions with 70% with about 2 mg/mL. The ability to XSM to influence cell proliferation in culture was also evaluated. This polymer did not influence the proliferation of normal fibroblast cells (3T3), however, decreased the rate of proliferation of tumor cells (HeLa) in a dose-dependent, reaching an inhibition of about 50% with a concentration around 2 mg/mL. Analyzing proteins related to cell death, by immunoblotting, XSM increases the amount of Bax, Bcl-2 decrease, increase cytochrome c and AIF, and reduce pro-caspase-3, indicating the induction of cell death induced apoptosis dependent and independent of caspase. XSM did not show anticoagulant activity in the PT test. However, the test of activated partial thromboplastin time (aPTT), XSM increased clotting time at about 5 times with 600 μg of sample compared with the negative control. The presence of sulfate on the XSM was discarded by agarose gel electrophoresis and IR. After carboxyl-reduction of XSM the anticoagulant activity decreased dramatically. The data of this study demonstrate that XSM has potential as antioxidant, antiproliferative and anticoagulant compound. Future studies to characterize these activities of XSM will help to increase knowledge about this molecule extracted from corn and allow their use in functional foods, pharmaceuticals and chemical industries.

Associação de bioensaios e caracterização molecular para seleção de novos isolados de Bacillus thuringiensis efetivos contra Spodoptera frugiperda (J.E. Smith) (Lepidoptera: Noctuidae)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evaluation of corn cultivars harvested at two cutting heights for ensilage

Objetivou-se neste estudo avaliar as características agronômicas, a composição químico-bromatológica e a digestibilidade de 11 cultivares de milho (Zea mays) colhido em duas alturas de corte. As cultivares D 766, D 657, D 1000, P 3021, P 3041, C 805, C 333, AG 5011, FO 01, CO 9621 e BR 205 foram avaliadas quando colhidas 5 cm acima do solo (baixa) e 5 cm abaixo da inserção da primeira espiga (alta). O experimento foi delineado como blocos casualizados, com três repetições, arranjados em esquema fatorial 11 x 2. Os cultivares apresentaram produções semelhantes de matéria seca de forragem e de grãos. As porcentagens das frações colmo, folha, palha, sabugo e grão diferiram entre os cultivares, assim como os teores de matéria seca da planta inteira no momento da colheita. Considerando a planta inteira, apenas os teores de energia bruta, nitrogênio da fração fibra em detergente neutro e a digestibilidade in vitro da fibra em detergente neutro e detergente ácido não diferiram entre os cultivares. O aumento da altura de corte melhorou a qualidade da forragem, devido à redução das frações colmo e folha e dos teores dos constituintes da parede celular.

Avaliação da queima e da adição de milho desintegrado com palha e sabugo na ensilagem de cana-de-açúcar

Neste trabalho, avaliou-se a fermentação da cana-de-açúcar queimada, ensilada com ou sem uso de aditivo seco. Os tratamentos (seis no total) consistiram da silagem de cana crua ou queimada, adicionada de 0, 50 ou 100 g/kg de milho desintegrado com palha e sabugo (MDPS), com base no peso verde da forragem. Foram determinados os teores de MS, PB, nitrogênio insolúvel em detergente ácido (NIDA), FDN, FDA, celulose, hemicelulose e lignina. Na avaliação das características fermentativas, foram determinados os valores de carboidratos solúveis, o poder tamponante, o pH e as concentrações de nitrogênio amoniacal e etanol. Como características microbiológicas, avaliou-se o desenvolvimento de leveduras. A inclusão de MDPS elevou os teores de MS e reduziu discretamente os teores de N-NH3 e etanol das silagens, não ocasionando efeito nos valores de pH e na população de leveduras. A presença do fogo reduziu a concentração de MS das silagens, elevou os teores de etanol e leveduras e diminuiu os teores de N-NH3. A fermentação etanólica durante a ensilagem não foi controlada com a inclusão de aditivo seco ou com o uso do fogo.

Densidades populacionais de milho em arranjos espaciais convencional e equidistante entre plantas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Seletividade do nicosulfuron em três estádios fenológicos de milho-pipoca

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bromatological evaluation of eleven corn cultivars harvested at two cutting heights

The objective of this study was to evaluate the chemical composition and dry matter in vitro digestibility of stem, leaf, straw, cob and kernel fractions of eleven corn (Zea mays) cultivars, harvested at two cutting heights. The experiment was designed as randomized blocks, with three replicates, in a 2 × 11 factorial arrangement (eleven cultivars and two cutting heights). The corn cultivars evaluated were D 766, D 657, D 1000, P 3021, P 3041, C 805, C 333, AG 5011, FOR 01, CO 9621 and BR 205, harvested at a low cutting height (5 cm above ground) and a high cutting height (5 cm below the first ear insertion). Cutting height influenced the dry matter content of the stem fraction, which was lower (23.95%) in plants harvested at the low, than in plants harvested at the high cutting height (26.28%). The kernel fraction had the highest dry matter in vitro digestibility (85.13%), while cultivars did not differ between each other. Cob and straw were the fractions with the highest level of neutral detergent fiber (80.74 and 79.77%, respectively) and the lowest level of crude protein (3.84% and 3.69%, respectively). The leaf fraction had the highest crude protein content, both for plants of low and high cuttings (15.55% and 16.20%, respectively). The increase in the plant cutting height enhanced the dry matter content and dry matter in vitro digestibility of stem fraction, but did not affect the DM content of the leaf fraction.

Xylanolytic complex from Aspergillus giganteus: production and characterization

An Aspergillus giganteus strain was isolated as an excellent producer of xylanase associated with low levels of cellulase. Optimal xylanase production was obtained in liquid VOGEL medium containing xylan as carbon source, pH 6.5 to 7.0, at 25degreesC and. under shaking at 120 rpm during 84h. Among the several carbon sources tested, higher xylanase production was verified in xylan, xylose, sugar-cane bagasse, wheat bran and corn cob cultures, respectively. Optimal conditions for activity determination were 50degreesC and pH 6.0. The xylanolytic complex of A. giganteus showed low thermal stability with T-50 of 2 h, 13 min and I min when it was incubated at 40, 50 and 60degreesC, respectively, and high stability from pH 4.5 to 10.5, with the best interval between 7.0 to 7.5. This broad range of stability in alkali pH indicates a potential applicability in some industrial processes, which require such condition. Xylanolytic activity of A. giganteus was totally inhibited by Hg+2, Cu+2 and SDS at 10 mm. The analysis of the products from the oat spelts xylan hydrolysis through thin-layer chromatography indicated endoxylanase activity, lack of debranching enzymes and P-xylosidase activity in assay conditions.