957 resultados para Castro Silva, José Vicente


Relevância:

100.00% 100.00%

Publicador:

Resumo:

The red pottery industry in Piauí state is well developed and stands out at the national context for the technical quality of its products. The floor and wall tile industry, however, is little developed since the state has only one company that produces red clay-based ceramic tiles. This thesis aims at using the predominantly illitic basic mass of the above mentioned industry, with the addition of feldspar and/or kaolin residue in order to obtain products of higher technical quality. Kaolin residue consists basically of kaolinite, muscovite mica and quartz; the feldspar used was potassic. In this experiment, basic mass (MB) was used for experimental control and fifteen formulations codified as follows: F2, F4, F8, F16, F32, FR2, FR4, FR8, FR16, FR32, R2, R4, R8, R16 and R32. All raw materials were dry-milled, classified, formulated and then humidified to 10% water. Thereafter, test samples were produced by unixial pressing process in a rectangular steel matrix (60.0 x 20.0 x 5.0) mm3 at (25 MPa). They were fired at four temperatures: 1080°C, 1120°C, 1160°C, with a heating rate of 10°C/min during up to 10 min in an electric oven, and the last one in an industrial oven with a peak of 1140°C, aim ing to confirm the results found in laboratory and, finally, technological tests were performed: MEA, RL, AA, PA, TRF and PF. The results revealed that the residue under study can be considered a raw material with large potential in the industry of red clay-based ceramic tiles, since the results found both in laboratory and in the industry have shown that the test samples produced from the formulations with up to 4% feldspar and those produced with up to 8% feldspar and residue permitted a reduction in the water absorption rate and an increase in the mechanical resistance while those samples produced with up to 4% residue had an increase in the mechanical resistance when compared to those produced from the basic mass and that the formulation with 2% feldspar and residue presented the best technological properties, lowering the sintering temperature down to 1120°C

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Dois experimentos foram realizados para avaliar a interação fósforo disponível (Pd) × fitase (UF) da dieta sobre o desempenho, os níveis plasmáticos de fósforo e os parâmetros ósseos de poedeiras. No experimento 1, utilizaram-se 240 aves com 40 semanas de idade distribuídas em esquema fatorial 5 × 2, composto de cinco níveis de fósforo disponível (0,094; 0,194; 0,294; 0,394 e 0,494%) e dois de fitase (0 e 300 unidades de fitase - UF). No experimento 2, utilizaram-se 288 aves com 44 semanas de idade, distribuídas também em esquema fatorial 3 × 4, composto de três níveis de fósforo disponível (0,094; 0,294 e 0,494%) e quatro de fitase (0; 300; 600 e 1.200 UF). No experimento 1, não houve interação fósforo disponível × fitase, mas o nível de fósforo disponível influenciou, de forma quadrática, a produção (PR) e a massa (MO) de ovos, os níveis plasmáticos de fósforo e a conversão por massa de ovos (CMO) e, de forma linear, o teor de cinzas na tíbia (CT) e a resistência óssea (RO). A adição de 300 UF elevou a disponibilidade do fósforo (de 4,034 para 4,784 mg/dL), o teor de CT (de 41,55 para 42,90%) e a resistência óssea (de 9,678 para 11,135 kgf/mm). No experimento 2, a produção aumentou de forma linear com os níveis de fósforo disponível da ração, que aumentaram linearmente com o aumento do nível de fitase. Os teores de cinzas na tíbia aumentaram até o nível de 567 UF. O aumento do fósforo disponível no nível de 600 UF melhorou de forma linear a massa de ovos, a conversão por massa de ovos e a conversão por dúzia de ovos. A suplementação da ração com menor teor de fósforo disponível (0,094%) com 300 a 1.200 UF melhorou a resistência óssea das aves. Poedeiras exigem em média 0,31 a 0,34% Pd. A adição de 300 UF ou o aumento do fósforo disponível em rações com 600 UF melhora a conversão por massa de ovos. A suplementação de rações deficientes em fósforo disponível com pelo menos 300 UF aumenta os níveis plasmáticos de fósforo, os teores de cinzas na tíbia e a resistência óssea de poedeiras comerciais.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The present study presents an investigation concerning the factors that, in the perception of the extension of Emater/RN they affect the competitiveness of the productive chain of the coconut in Rio Grande do Norte. For so much it is used of a theory structured starting from the several aspects that delineate the competitiveness and your respective factors, besides the aspects that compose the productive chain of the coconut in Rio Grande do Norte. The research was accomplished at the mesorregião Leste Potiguar of Rio Grande do Norte, territory of larger index of coconut production in the state. The used methodological approach was the one of descriptive exploratory research together to the conduction of a rising type Survey. The field research obtained 35 valid questionnaires, whose interviewees were the extension of Emater/RN in performance in the municipal districts that compose the mesorregião Leste Potiguar of Rio Grande do Norte. The results allow to end that in the perception of the extension, the level of competitiveness of the productive chain of the coconut in Rio Grande do Norte is still low, presenting as larger fetter the low price of the coconut and the high costs of the productive process, being recommended a larger support to the producing of coconut in relation to technical attendance, incentive actions to the quality, understanding with relationship to the benefits of the creation of partnerships, associations and cooperatives, as well as the promotion of the knowledge of the productive chain of the coconut in Rio Grande do Norte for subsequent ends of all the agents' of that chain training with relationship to the importance of the development of competitive advantages

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Lithium (Li) is a chemical element with atomic number 3 and it is among the lightest known elements in the universe. In general, the Lithium is found in the nature under the form of two stable isotopes, the 6Li and 7Li. This last one is the most dominant and responds for about 93% of the Li found in the Universe. Due to its fragileness this element is largely used in the astrophysics, especially in what refers to the understanding of the physical process that has occurred since the Big Bang going through the evolution of the galaxies and stars. In the primordial nucleosynthesis in the Big Bang moment (BBN), the theoretical calculation forecasts a Li production along with all the light elements such as Deuterium and Beryllium. To the Li the BNB theory reviews a primordial abundance of Log log ǫ(Li) =2.72 dex in a logarithmic scale related to the H. The abundance of Li found on the poor metal stars, or pop II stars type, is called as being the abundance of Li primordial and is the measure as being log ǫ(Li) =2.27 dex. In the ISM (Interstellar medium), that reflects the current value, the abundance of Lithium is log ǫ(Li) = 3.2 dex. This value has great importance for our comprehension on the chemical evolution of the galaxy. The process responsible for the increasing of the primordial value present in the Li is not clearly understood until nowadays. In fact there is a real contribution of Li from the giant stars of little mass and this contribution needs to be well streamed if we want to understand our galaxy. The main objection in this logical sequence is the appearing of some giant stars with little mass of G and K spectral types which atmosphere is highly enriched with Li. Such elevated values are exactly the opposite of what could happen with the typical abundance of giant low mass stars, where convective envelops pass through a mass deepening in which all the Li should be diluted and present abundances around log ǫ(Li) ∼1.4 dex following the model of stellar evolution. In the Literature three suggestions are found that try to reconcile the values of the abundance of Li theoretical and observed in these rich in Li giants, but any of them bring conclusive answers. In the present work, we propose a qualitative study of the evolutionary state of the rich in Li stars in the literature along with the recent discovery of the first star rich in Li observed by the Kepler Satellite. The main objective of this work is to promote a solid discussion about the evolutionary state based on the characteristic obtained from the seismic analysis of the object observed by Kepler. We used evolutionary traces and simulation done with the population synthesis code TRILEGAL intending to evaluate as precisely as possible the evolutionary state of the internal structure of these groups of stars. The results indicate a very short characteristic time when compared to the evolutionary scale related to the enrichment of these stars

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Tireóide ectópica é qualquer tecido tireoideano localizado fora de sua topografia habitual, podendo apresentar-se na linha mediana do pescoço ou, mais raramente, na região cervical lateral. Algumas teorias tentam explicar a origem do tecido tireoideano ectópico: 1. falha na descida da glândula; 2. seqüestro de nódulos tireoideanos; 3. presença de tecido tireoideano na cápsula de linfonodos cervicais; 4. formação teratomatosa; 5. Secundário a anomalias branquiais. Na abordagem diagnóstica, diversos exames têm sido utilizados, sendo o diagnóstico definitivo algumas vezes fornecido apenas pelo estudo histopatológico. Apesar das controvérsias em relação às abordagens terapêuticas apresentadas na literatura, é necessário um planejamento rigoroso para evitar iatrogenias. Conclui-se que a presença de tecido tireoideano ectópico deve ser lembrada no diagnóstico diferencial de massas cervicais laterais, e sua origem histológica considerada, sendo na maioria das vezes metástase de um carcinoma tireoideano oculto. Os autores relatam um caso de tecido tireoideano ectópico lateral no pescoço, em paciente do sexo feminino com bócio colóide mergulhante. Foram realizadas considerações importantes sobre dismorfogênese tireoideana, métodos diagnósticos e opções de tratamento, com revisão da literatura das últimas cinco décadas.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Relevância:

100.00% 100.00%

Publicador:

Resumo:

O resultado pós-operatório das tireoidectomias é imputado a fatores relativos ao paciente, à tireopatia e ao cirurgião. OBJETIVO: Analisar a experiência de um serviço quanto a complicações com a tireoidectomia. Desenho do estudo: coorte histórica com corte transversal. MATERIAL E MÉTODO: Foram avaliados os prontuários de 228 pacientes submetidos à tireoidectomia, entre 1991 e 2004. Foram estudadas as complicações transitórias, definitivas e totais, persistência e recidiva da tireopatia de base, em relação a fatores clínico-laboratoriais. RESULTADOS: Ocorreram 34,65% de complicações totais, 18,86% de complicações transitórias (9,21% hipocalcemia, 0,44% paralisia de cordas vocais, 4,82% outras), associadas aos primeiros anos de cirurgia no serviço e queixas compressivas, e 17,98% de complicações definitivas (8,77% hipoparatireoidismo, 1,75% paralisia de cordas vocais, 0,44% rouquidão), associadas à malignidade e cirurgias mais radicais. Houve persistência da doença de base em 17,98% dos casos, associada à idade, e recidiva em 10,96%, associada aos primeiros anos de cirurgia, benignidade e cirurgias menos radicais. CONCLUSÃO: Complicações pós-operatórias se associaram a queixas compressivas, história curta, malignidade e cirurgias mais radicais. A recidiva se associou aos primeiros anos de cirurgia no serviço, tireopatias benignas e cirurgias menos radicais. A persistência da doença se associou à maior idade.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The study of solar neutrinos is very important to a better comprehension of the set of nuclear reactions that occurs inside the Sun and in solar type stars. The ux of neutrinos provides a better comprehension of the stellar structure as a whole. In this dissertation we study the ux of neutrinos in a solar model, addressing the neutrino oscillation, analyzing with the intention of determining and verify the distribution from a statistical point of view, since this ux depends on the particles intrinsic velocity distributions in stellar plasma. The main tool for this analysis was the Toulouse-Geneva Stellar Evolution Code, or TGEC, which allow us to obtain the neutrino ux values per reaction and per layer inside the Sun, allowing us to compare the observational results for the neutrino ux detected on experiments based on Cl37 (Homestake), Ga71 (SAGE, Gallex/GNO) and water (SNO). Our results show the nal distribution for neutrino ux as a function of the depth using the coordinates of mass and radius. The dissertation also shows that the equations for this ux are present in TGEC.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A osteomalacia oncogênica é um diagnóstico clínico desafiador, caracterizado pela perda renal de fosfato e baixos níveis de 1,25-di-hidroxivitamina D3, ocorrendo na presença de um tumor produtor de altos níveis de fator de crescimento de fibroblasto 23. No entanto, é possível que se trate muito mais de uma falha de diagnóstico clínico do que propriamente uma doença rara. Os autores relatam o caso de um homem de 42 anos com histórico de fraqueza muscular progressiva por cinco anos e restrição à cadeira de rodas, sem diagnóstico. Seus exames laboratoriais evidenciavam baixos níveis de fósforo. A remoção cirúrgica de um hemangiopericitoma detectado previamente em cavidade nasal levou à resolução completa dos sintomas. Os autores enfatizam que, mesmo com a etiologia já evidenciada, o paciente consultou diversos clínicos no decorrer dos cinco anos até que fossem instituídos o diagnóstico e o tratamento adequados. Arq Bras Endocrinol Metab. 2012;56(8):570-3

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The sedimentary Curitiba basin is located in the Central-Southern part of the first Parananense plateau, and comprises Curitiba (PR), and part of the neighbour Municipalities (fig.1). It is supposed to be of Plio-Pleistocene age. It has a shallow sedimentary fulfillment, represented by the Guabirotuba formation (BIGARELLA and SALAMUNI, 1962) which is dristributed over a large area of about 3.000km2. The internal geometry, not entirely known yet, is actually object of detailed research, that shows its geological evolution to Cenozoic tectonic movements. For the purpose of this study the definition of the structural contour of the basement and their depo-centers is fundamental. This paper presents the results of the integration of surface and subsurface data, processed by statistical methods, which allowed a more precise definition of the morphostructural framework of the basement. For the analysis of the geological spacial data, specific softwares were used for statistical processing for trend surfaces analysis. The data used in this study are of following types: a) drilling logs for ground water; b) description of surface points of geological maps (CRPM, 1977); c) description of points of geotechnical drillings and down geological survey. The data of 223 drilling logs for ground water were selected out of 770 wells. The description files of 700 outcrops, as well as planialtimetric field data, were used for the localization of the basement outcrop. Thus, a matrix with five columns was set up: utm E-W (x) and utm N-S (y); surface altitude (z); altimetric cote of the contact between sedimentary rocks and the basement (k); isopachs (l). For the study of the basement limits, the analysis of surface trends of 2(nd) and 3(rd) degree polinomial for the altimetric data (figs. 2 and 3) were used. For the residuals the method of the inverse of the square of the distance (fig.4) was used. The adjustments and the explanations of the surfaces were made with the aid of multiple linear regressions. The analysis of 3rd degree polinomial trend surface (fig.3) confirmed that the basement tends to be more exposed towards NNW-SSE explaining better the data trend through an ellipse, which striking NE-SW and dipping SW axis coincides with the trough of the basin observed in the trending surface of the basement. The performed analysis and the respective images offer a good degree of certainty of the geometric model of the Curitiba Basin and of the morphostructure of its basement. The surface trend allows to sketch with a greater degree of confidence the structural contour of the topgraphic surface (figs. 5 and 6) and of the basement (figs. 7 and 8), as well as the delimitation of intermediate structural heights, which were responsible for isolated and assymmetric depocenters. These details are shown in the map of figures 9 and 10. Thus, the Curitiba Basin is made up by a structural trough stretching NE-SW, with maximum preserved depths of about 80m, which are separated by heights and depocenters striking NW-SE (fig. 11). These structural features seems to have been controlled by tectonic reactivation during the Tertiary (HASUI, 1990) and which younger dissection was conditioned by neotectonic processes (SALAMUNI and EBERT, 1994).

Relevância:

100.00% 100.00%

Publicador:

Resumo:

It is presented two study cases about the approach in root analysis at field and laboratory conditions based on digital image analysis. Grapevine (Vitis vinifera L.) and date palm (Phoenix dactylifera L.) root systems were analyzed by both the monolith and trench wall method aided by digital image analysis. Correlation between root parameters and their fractional distribution over the soil profile were obtained, as well as the root diameter estimation. Results have shown the feasibility of digital image analysis for evaluation of root distribution.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Global interest in sugarcane has increased significantly in recent years due to its economic impact on sustainable energy production. Sugarcane breeding and better agronomic practices have contributed to a huge increase in sugarcane yield in the last 30 years. Additional increases in sugarcane yield are expected to result from the use of biotechnology tools in the near future. Genetically modified (GM) sugarcane that incorporates genes to increase resistance to biotic and abiotic stresses could play a major role in achieving this goal. However, to bring GM sugarcane to the market, it is necessary to follow a regulatory process that will evaluate the environmental and health impacts of this crop. The regulatory review process is usually accomplished through a comparison of the biology and composition of the GM cultivar and a non-GM counterpart. This review intends to provide information on non-GM sugarcane biology, genetics, breeding, agronomic management, processing, products and byproducts, as well as the current technologies used to develop GM sugarcane, with the aim of assisting regulators in the decision-making process regarding the commercial release of GM sugarcane cultivars. © 2011 The Author(s).