Annealing response of the intermetallic alloy Ti-22Al-25Nb

A hot rolled two-phase Ti-22Al-25Nb (at.%) alloy containing the orthorhombic (O) and beta(B2) phases was subjected to thermal treatment under different conditions. The experiment was aimed to examine the recrystallization response of the beta(B2) phase (static and dynamic) to microstructure and crystallographic texture evolution using scanning electron microscopy coupled with electron backscattered diffraction (SEM-EBSD). Specimens rolled in the two-phase (O + beta(B2)) region consisted of highly deformed beta(B2) grains. The texture was close to that of the typical bcc deformation texture with a few additional texture components. A subsequent heat treatment of these rolled specimens in single beta(B2) phase region was characterized by static recrystallized beta(B2) grains with the final texture partly inherited from as-rolled material. In contrast, specimens rolled in the single beta(B2) region produced beta(B2) grains with the texture similar to that of completely dynamic recrystallized one. (C) 2010 Elsevier Ltd. All rights reserved.

Effect of interface friction on the mechanics of indentation of a finite layer resting on a rigid substrate

Copper strips of 2.5 mm thickness resting on stainless steel anvils were normally indented by wedges under nominal plane strain conditions. Inflections in the hardness-penetration characteristics were identified. Inflections separate stages where each stage has typical mechanics of deformation. These are arrived at by studying the distortion of 0.125 mm spaced grids inscribed on the deformation plane of the strip. The sensitivity of hardness and deformation mechanics to wedge angle and the interfacial friction between strip and anvil were investigated within the framework of existing slip line field models of indentation of semi-infinite and finite blocks.

Studies on helium flow in experimental loops with different impedances operated with fountain effect pumps

An experimental flow loop with He II flow driven by fountain effect pumps (FEPs) is studied with respect to operation at different flow impedances and with thermal loads applied at different positions. The measured values of temperature, flow rate and pressure drop are compared with calculations resulting from a simplified model which assumes ideal performance of the porous plug and of the heat exchangers and which does not take into account Gorter-Mellink (GM) conduction. The main features of the loop are shown to be well described by this model. Refined calculations with a more complex model, including GM conduction of the He II, are only required for predicting the temperature distribution in some discrete regions of the loop.

An electron-spin-resonance study of MN2+ doped calcium hydrazine carboxylate monohydrate

Single crystals of calcium hydrazine carboxylate, monohydrate have been studied by ESR of Mn2+ doped in the calcium sites. X-band ESR indicated a large crystal field splitting necessitating experiments at Q band. The analysis shows two magnetically inequivalent (but chemically equivalent) sites with g(xx) = 2.0042+/-0.0038, g(yy) = 2.0076 +/-00029, g(zz) =2.0314+/-0.001, A(zz) = 0.0099+/-0.0002 cm(-1), A(xx) = 0.0099+/-0.0002 cm(-1), A(yy) = 0.0082+/-0.0002cm(-1), D = 3/2D(zz) = 0.0558+/-0.0006cm(-1), and E = 1/2(D-xx-D-yy) = 0.0127+/-0.0002 cm(-1).One of the principal components of the crystal field, (D-zz), is found to be along the Ca<->Ca direction in the structure and a second one, (D-xx), along the perpendicular to the plane of the triangle formed by three neighbouring calciums. The A tensor is found to have an orientation different from that of the g and D tensors reflecting the low symmetry of the Ca2+ sites.

Enhancement in Bath Mixing and Plume area in a New Degassing Process - A Computational Fluid Dynamic Study

Reaction between the various species in slag and metal phase is usually mass transfer controlled. There have been continuous efforts to increase the reaction efficiency in slag-metal system, especially during decarburization of steel to produce the ultra low carbon steel (ULCS) in secondary steelmaking. It has been found that the surface reaction is a dominant factor in the final stage of decarburization. In the initial stage, the inner site reaction is major factor in the refining process. The mixing of bath affects the later reaction. However, the former reaction (surface reaction) is affected by the plume size area at the top of the metal surface. Therefore, a computational study has been made to understand the fluid dynamics of a new secondary steelmaking process called Revolutionary Degasser Activator (REDA) to study the bath mixing and plume area. REDA process has been considered as it is claimed that this process can reduce the carbon content in steel below 10ppm in a less time than the other existing processes such as RH and Tank degasser. This study shows that both bath mixing and plume area are increased in REDA process facilitating it to give the desired carbon content in less time. Qualitative comments are made on slag-metal reaction system based on this finding.

The 2D Coulomb gas on a 1D lattice

The statistical mechanics of a two-dimensional Coulomb gas confined to one dimension is studied, wherein hard core particles move on a ring. Exact self-duality is shown for a version of the sine-Gordon model arising in this context, thereby locating the transition temperature exactly. We present asymptotically exact results for the correlations in the model and characterize the low- and high-temperature phases. Numerical simulations provide support to these renormalization group calculations. Connections with other interesting problems, such as the quantum Brownian motion of a panicle in a periodic potential and impurity problems, are pointed out.

Studies on a new high-intensity low-emission burner

This paper presents computational and experimental results on a new burner configuration with a mild combustion concept with heat release rates up to 10 MW/m(3). The burner configuration is shown to achieve mild combustion by using air at ambient temperature at high recirculation rates (similar to250%-290%) both experimentally and computationally. The principal features of the configuration are: (1) a burner with forward exit for exhaust gases; (2) injection of gaseous fuel and air as multiple, alternate, peripheral highspeed jets at the bottom at ambient temperature, thus creating high enough recirculation rates of the hot combustion products into fresh incoming reactants; and (3) use of a suitable geometric artifice-a frustum of a cone to help recirculation. The computational studies have been used to reveal the details of the flow and to optimize the combustor geometry based on recirculation rates. Measures, involving root mean square temperature fluctuations, distribution of temperature and oxidizer concentration inside the proposed burner, and a classical turbulent diffusion jet flame, are used to distinguish between them quantitatively. The system, operated at heat release rates of 2 to 10 MW/m(3) (compared to 0.02 to 0.32 MW/m(3) in the earlier studies), shows a 10-15 dB reduction in noise in the mild combustion mode compared to a simple open-top burner and exhaust NOx emission below 10 ppm for a 3 kW burner with 10% excess air. The peak temperature is measured around 1750 K, approximately 300 K lower than the peak temperature in a conventional burner.

Fracture and R-curves in high volume fraction Al2O3/Al composites

Fracture toughness and fracture mechanisms in Al2O3/Al composites are described. The unique flexibility offered by pressureless infiltration of molten Al alloys into porous alumina preforms was utilized to investigate the effect of microstructural scale and matrix properties on the fracture toughness and the shape of the crack resistance curves (R-curves). The results indicate that the observed increment in toughness is due to crack bridging by intact matrix ligaments behind the crack tip. The deformation behavior of the matrix, which is shown to be dependent on the microstructural constraints, is the key parameter that influences both the steady-state toughness and the shape of the R-curves. Previously proposed models based on crack bridging by intact ductile particles in a ceramic matrix have been modified by the inclusion of an experimentally determined plastic constraint factor (P) that determines the deformation of the ductile phase and are shown to be adequate in predicting the toughness increment in the composites. Micromechanical models to predict the crack tip profile and the bridge lengths (L) correlate well with the observed behavior and indicate that the composites can be classified as (i) short-range toughened and (ii) long-range toughened on the basis of their microstructural characteristics.

Quantum capacitance in bilayer graphene nanoribbon

We address a physically based analytical model of quantum capacitance (C-Q) in a bilayer graphene nanoribbon (BGN) under the application of an external longitudinal static bias. We demonstrate that as the gap (Delta) about the Dirac point increases, a phenomenological population inversion of the carriers in the two sets of subbands occurs. This results in a periodic and composite oscillatory behavior in the C-Q with the channel potential, which also decreases with increase in Delta. We also study the quantum size effects on the C-Q, which signatures heavy spatial oscillations due to the occurrence of van Hove singularities in the total density-of-states function of both the sets of subbands. All the mathematical results as derived in this paper converge to the corresponding well-known solution of graphene under certain limiting conditions and this compatibility is an indirect test of our theoretical formalism. (C) 2012 Elsevier By. All rights reserved.

Assessing resilience and state-transition models with historical records of cheatgrass Bromus tectorum invasion in North American sagebrush-steppe

1. Resilience-based approaches are increasingly being called upon to inform ecosystem management, particularly in arid and semi-arid regions. This requires management frameworks that can assess ecosystem dynamics, both within and between alternative states, at relevant time scales. 2. We analysed long-term vegetation records from two representative sites in the North American sagebrush-steppe ecosystem, spanning nine decades, to determine if empirical patterns were consistent with resilience theory, and to determine if cheatgrass Bromus tectorum invasion led to thresholds as currently envisioned by expert-based state-and-transition models (STM). These data span the entire history of cheatgrass invasion at these sites and provide a unique opportunity to assess the impacts of biotic invasion on ecosystem resilience. 3. We used univariate and multivariate statistical tools to identify unique plant communities and document the magnitude, frequency and directionality of community transitions through time. Community transitions were characterized by 37-47% dissimilarity in species composition, they were not evenly distributed through time, their frequency was not correlated with precipitation, and they could not be readily attributed to fire or grazing. Instead, at both sites, the majority of community transitions occurred within an 8-10year period of increasing cheatgrass density, became infrequent after cheatgrass density peaked, and thereafter transition frequency declined. 4. Greater cheatgrass density, replacement of native species and indication of asymmetry in community transitions suggest that thresholds may have been exceeded in response to cheatgrass invasion at one site (more arid), but not at the other site (less arid). Asymmetry in the direction of community transitions also identified communities that were at-risk' of cheatgrass invasion, as well as potential restoration pathways for recovery of pre-invasion states. 5. Synthesis and applications. These results illustrate the complexities associated with threshold identification, and indicate that criteria describing the frequency, magnitude, directionality and temporal scale of community transitions may provide greater insight into resilience theory and its application for ecosystem management. These criteria are likely to vary across biogeographic regions that are susceptible to cheatgrass invasion, and necessitate more in-depth assessments of thresholds and alternative states, than currently available.

A comparative study of room temperature ferromagnetism in MgO films deposited by rf/dc sputtering using high purity Mg and MgO targets

Thin films of nanocrystalline MgO were deposited on glass/Si substrates by rf/dc sputtering from metallic Mg, and ceramic MgO targets. The purpose of this study is to identify the differences in the properties, magnetic in particular, of MgO films obtained on sputter deposition from 99.99% pure metallic Mg target in a controlled Nitrogen + Oxygen partial pressure (O(2)pp)] atmosphere as against those deposited using an equally pure ceramic MgO target in argon + identical oxygen ambience conditions while maintaining the same total pressure in the chamber in both cases. Characterization of the films was carried out by X-ray diffraction, focussed ion beam cross sectioning, atomic force microscopy and SQUID-magnetometry. The `as-obtained' films from pure Mg target are found to be predominantly X-ray amorphous, while the ceramic MgO target gives crystalline films, (002) oriented with respect to the film plane. The films consisted of nano-crystalline grains of size in the range of about 0.4 to 4.15 nm with the films from metallic target being more homogeneous and consisting of mostly subnanometer grains. Both the types of films are found to be ferromagnetic to much above room temperature. We observe unusually high maximum saturation magnetization (MS) values of 13.75 emu/g and similar to 4.2 emu/g, respectively for the MgO films prepared from Mg, and MgO targets. The origin of magnetism in MgO films is attributed to Mg vacancy (V-Mg), and 2p holes localized on oxygen sites. The role of nitrogen in enhancing the magnetic moments is also discussed.

Effect of structural relaxation on deformation behaviour of Zr-based metallic glass

Structural relaxation through isothermal annealing at tempertature below glass transition is conducted on Zr46.75Ti8.25Cu7.5Ni10Be27.5 (Vitreloy-4) bulk metallic glass. Defect concentration is correlated with the annealing time t according to differential scanning calorimetry thermalgrams. The effects of structural relaxation on mechanical properties and deformation behaviour are investigated by using instrumented nanoindentation. It is found that as-cast alloy exhibits pronounced serration flow during the loading process of nanoindentation, and the size and number of serrations decrease with the annealing time. The change of the deformation behaviour with structural relaxation is explained using a free volume model.

La gestión del conocimiento científico-técnico en la universidad: un caso y un proyecto

[ES] Actualmente, las universidades se enfrentan a aumentos en sus necesidades de financiación, cuando el criterio predominante es que los poderes públicos tengan una menor presencia en la misma. Por otra parte, algunos investigadores indican que la Universidad parece estar perdiendo posiciones como centro de generación de conocimiento, el cual, como recurso en s. mismo, este siendo objeto de creciente atención por parte de las empresas y los gobiernos, considerándose le el recurso clave en la consecución de ventajas competitivas. En estas circunstancias, estimamos que la Universidad debe hacer mayores esfuerzos en orientar su investigación a la aplicación del conocimiento científico-técnico, en colaboración con las empresas y las administraciones públicas, como indica el modelo de la triple hélice de Etzkowitz y Leydesdorff. En este trabajo se presenta también como se afronta en la Universidad del País Vasco/Euskal Herriko Unibertsitatea la gestión del conocimiento científico técnico, as. como un proyecto de investigación cuya finalidad consiste en la búsqueda de un modelo de gestión de este conocimiento en el contexto descrito.

La influencia del factor dimensión en la pertenencia a centrales de compra por parte del pequeño comercio

[ES] Desde hace varios años, el pequeño comercio en España y en otros países europeos viene enfrentándose a un entorno de creciente concurrencia, con la irrupción de nuevas formas comerciales más integradas vertical u horizontalmente, y mejor preparadas para competir en precio y variedad. Ante este hecho, las centrales de compra se ofrecen como una alternativa tendente a acortar distancias en estas dos cuestiones, a la vez que buscan la prestación de ciertos servicios que ayuden al pequeño comerciante a gestionar más eficaz y eficientemente su negocio.