Self-assembly of Pd(II) pyrazolyl complexes to 1-D hydrogen-bonded coordination polymers

This work describes the synthesis and characterization of two novel Pd(II) pyrazolyl complexes of the type [PdX2(HdmPz)(2)](n) {X=SCN- (1), N-3(-) (2); HdmPz=3,5-dimethylpyrazole} that self-assemble through N-H...NCS or N-H...NNN hydrogen bonds to yield infinite one-dimensional chains, as confirmed by single crystal X-ray study on 1. The expected solid state polymeric structure for 2 is slowly broken up in CHCl3 Solution, leading to an equilibrium mixture of cis and trans-[Pd(N-3)(2)(HdmPz)(2)] monomers, as demonstrated by time-dependent IR and NMR studies. (C) 2003 Elsevier B.V. B.V. All rights reserved.

Gravitação quadrática em (2 + 1)D com e sem termo topológico de Chern-Simons

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Convergence towards asymptotic state in 1-D mappings: a scaling investigation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Eletrodinâmica de ordem superior em (2+1)D

Pós-graduação em Física - IFT

Loss of the anorexic response to systemic 5-aminoimidazole-4-carboxamide-1-β-D-ribofuranoside administration despite reducing hypothalamic AMP-activated protein kinase phosphorylation in insulin-deficient rats

This study tested whether chronic systemic administration of 5-aminoimidazole-4-carboxamide-1-β-D-ribofuranoside (AICAR) could attenuate hyperphagia, reduce lean and fat mass losses, and improve whole-body energy homeostasis in insulin-deficient rats. Male Wistar rats were first rendered diabetic through streptozotocin (STZ) administration and then intraperitoneally injected with AICAR for 7 consecutive days. Food and water intake, ambulatory activity, and energy expenditure were assessed at the end of the AICAR-treatment period. Blood was collected for circulating leptin measurement and the hypothalami were extracted for the determination of suppressor of cytokine signaling 3 (SOCS3) content, as well as the content and phosphorylation of AMP-kinase (AMPK), acetyl-CoA carboxylase (ACC), and the signal transducer and activator of transcription 3 (STAT3). Rats were thoroughly dissected for adiposity and lean body mass (LBM) determinations. In non-diabetic rats, despite reducing adiposity, AICAR increased (∼1.7-fold) circulating leptin and reduced hypothalamic SOCS3 content and food intake by 67% and 25%, respectively. The anorexic effect of AICAR was lost in diabetic rats, even though hypothalamic AMPK and ACC phosphorylation markedly decreased in these animals. Importantly, hypothalamic SOCS3 and STAT3 levels remained elevated and reduced, respectively, after treatment of insulin-deficient rats with AICAR. Diabetic rats were lethargic and displayed marked losses of fat and LBM. AICAR treatment increased ambulatory activity and whole-body energy expenditure while also attenuating diabetes-induced fat and LBM losses. In conclusion, AICAR did not reverse hyperphagia, but it promoted anti-catabolic effects on skeletal muscle and fat, enhanced spontaneous physical activity, and improved the ability of rats to cope with the diabetes-induced dysfunctional alterations in glucose metabolism and whole-body energy homeostasis.

Entanglement entropy in 1-d quantum spin chains

In questa tesi abbiamo studiato il comportamento delle entropie di Entanglement e dello spettro di Entanglement nel modello XYZ attraverso delle simulazioni numeriche. Le formule per le entropie di Von Neumann e di Renyi nel caso di una catena bipartita infinita esistevano già, ma mancavano ancora dei test numerici dettagliati. Inoltre, rispetto alla formula per l'Entropia di Entanglement di J. Cardy e P. Calabrese per sistemi non critici, tali relazioni presentano delle correzioni che non hanno ancora una spiegazione analitica: i risultati delle simulazioni numeriche ne hanno confermato la presenza. Abbiamo inoltre testato l'ipotesi che lo Schmidt Gap sia proporzionale a uno dei parametri d'ordine della teoria, e infine abbiamo simulato numericamente l'andamento delle Entropie e dello spettro di Entanglement in funzione della lunghezza della catena di spin. Ciò è stato possibile solo introducendo dei campi magnetici ''ad hoc'' nella catena, con la proprietà che l'andamento delle suddette quantità varia a seconda di come vengono disposti tali campi. Abbiamo quindi discusso i vari risultati ottenuti.

Edge states and zero modes in quadratic fermionic models on a 1-D lattice

In una formulazione rigorosa della teoria quantistica, la definizione della varietà Riemanniana spaziale su cui il sistema è vincolato gioca un ruolo fondamentale. La presenza di un bordo sottolinea l'aspetto quantistico del sistema: l'imposizione di condizioni al contorno determina la discretizzazione degli autovalori del Laplaciano, come accade con condizioni note quali quelle periodiche, di Neumann o di Dirichlet. Tuttavia, non sono le uniche possibili. Qualsiasi condizione al bordo che garantisca l'autoaggiunzione dell' operatore Hamiltoniano è ammissibile. Tutte le possibili boundary conditions possono essere catalogate a partire dalla richiesta di conservazione del flusso al bordo della varietà. Alcune possibili condizioni al contorno, permettono l'esistenza di stati legati al bordo, cioè autostati dell' Hamiltoniana con autovalori negativi, detti edge states. Lo scopo di questa tesi è quello di investigare gli effetti di bordo in sistemi unidimensionali implementati su un reticolo discreto, nella prospettiva di capire come simulare proprietà di edge in un reticolo ottico. Il primo caso considerato è un sistema di elettroni liberi. La presenza di edge states è completamente determinata dai parametri di bordo del Laplaciano discreto. Al massimo due edge states emergono, e possono essere legati all' estremità destra o sinistra della catena a seconda delle condizioni al contorno. Anche il modo in cui decadono dal bordo al bulk e completamente determinato dalla scelta delle condizioni. Ammettendo un' interazione quadratica tra siti primi vicini, un secondo tipo di stati emerge in relazione sia alle condizioni al contorno che ai parametri del bulk. Questi stati sono chiamati zero modes, in quanto esiste la possibilità che siano degeneri con lo stato fondamentale. Per implementare le più generali condizioni al contorno, specialmente nel caso interagente, è necessario utilizzare un metodo generale per la diagonalizzazione, che estende la tecnica di Lieb-Shultz-Mattis per Hamiltoniane quadratiche a matrici complesse.

Quantum simulation of (1+1)D QED via a Zn lattice Gauge theory

La simulazione di un sistema quantistico complesso rappresenta ancora oggi una sfida estremamente impegnativa a causa degli elevati costi computazionali. La dimensione dello spazio di Hilbert cresce solitamente in modo esponenziale all'aumentare della taglia, rendendo di fatto impossibile una implementazione esatta anche sui più potenti calcolatori. Nel tentativo di superare queste difficoltà, sono stati sviluppati metodi stocastici classici, i quali tuttavia non garantiscono precisione per sistemi fermionici fortemente interagenti o teorie di campo in regimi di densità finita. Di qui, la necessità di un nuovo metodo di simulazione, ovvero la simulazione quantistica. L'idea di base è molto semplice: utilizzare un sistema completamente controllabile, chiamato simulatore quantistico, per analizzarne un altro meno accessibile. Seguendo tale idea, in questo lavoro di tesi si è utilizzata una teoria di gauge discreta con simmetria Zn per una simulazione dell'elettrodinamica quantistica in (1+1)D, studiando alcuni fenomeni di attivo interesse di ricerca, come il diagramma di fase o la dinamica di string-breaking, che generalmente non sono accessibili mediante simulazioni classiche. Si propone un diagramma di fase del modello caratterizzato dalla presenza di una fase confinata, in cui emergono eccitazioni mesoniche ed antimesoniche, cioè stati legati particella-antiparticella, ed una fase deconfinata.

Filtration and oxidation characteristics of a diesel oxidation catalyst and a catalyzed particulate filter : development of a 1-D 2-layer model

The emissions, filtration and oxidation characteristics of a diesel oxidation catalyst (DOC) and a catalyzed particulate filter (CPF) in a Johnson Matthey catalyzed continuously regenerating trap (CCRT ®) were studied by using computational models. Experimental data needed to calibrate the models were obtained by characterization experiments with raw exhaust sampling from a Cummins ISM 2002 engine with variable geometry turbocharging (VGT) and programmed exhaust gas recirculation (EGR). The experiments were performed at 20, 40, 60 and 75% of full load (1120 Nm) at rated speed (2100 rpm), with and without the DOC upstream of the CPF. This was done to study the effect of temperature and CPF-inlet NO2 concentrations on particulate matter oxidation in the CCRT ®. A previously developed computational model was used to determine the kinetic parameters describing the oxidation characteristics of HCs, CO and NO in the DOC and the pressure drop across it. The model was calibrated at five temperatures in the range of 280 – 465° C, and exhaust volumetric flow rates of 0.447 – 0.843 act-m3/sec. The downstream HCs, CO and NO concentrations were predicted by the DOC model to within ±3 ppm. The HCs and CO oxidation kinetics in the temperature range of 280 - 465°C and an exhaust volumetric flow rate of 0.447 - 0.843 act-m3/sec can be represented by one ’apparent’ activation energy and pre-exponential factor. The NO oxidation kinetics in the same temperature and exhaust flow rate range can be represented by ’apparent’ activation energies and pre-exponential factors in two regimes. The DOC pressure drop was always predicted within 0.5 kPa by the model. The MTU 1-D 2-layer CPF model was enhanced in several ways to better model the performance of the CCRT ®. A model to simulate the oxidation of particulate inside the filter wall was developed. A particulate cake layer filtration model which describes particle filtration in terms of more fundamental parameters was developed and coupled to the wall oxidation model. To better model the particulate oxidation kinetics, a model to take into account the NO2 produced in the washcoat of the CPF was developed. The overall 1-D 2-layer model can be used to predict the pressure drop of the exhaust gas across the filter, the evolution of particulate mass inside the filter, the particulate mass oxidized, the filtration efficiency and the particle number distribution downstream of the CPF. The model was used to better understand the internal performance of the CCRT®, by determining the components of the total pressure drop across the filter, by classifying the total particulate matter in layer I, layer II, the filter wall, and by the means of oxidation i.e. by O2, NO2 entering the filter and by NO2 being produced in the filter. The CPF model was calibrated at four temperatures in the range of 280 – 465 °C, and exhaust volumetric flow rates of 0.447 – 0.843 act-m3/sec, in CPF-only and CCRT ® (DOC+CPF) configurations. The clean filter wall permeability was determined to be 2.00E-13 m2, which is in agreement with values in the literature for cordierite filters. The particulate packing density in the filter wall had values between 2.92 kg/m3 - 3.95 kg/m3 for all the loads. The mean pore size of the catalyst loaded filter wall was found to be 11.0 µm. The particulate cake packing densities and permeabilities, ranged from 131 kg/m3 - 134 kg/m3, and 0.42E-14 m2 and 2.00E-14 m2 respectively, and are in agreement with the Peclet number correlations in the literature. Particulate cake layer porosities determined from the particulate cake layer filtration model ranged between 0.841 and 0.814 and decreased with load, which is about 0.1 lower than experimental and more complex discrete particle simulations in the literature. The thickness of layer I was kept constant at 20 µm. The model kinetics in the CPF-only and CCRT ® configurations, showed that no ’catalyst effect’ with O2 was present. The kinetic parameters for the NO2-assisted oxidation of particulate in the CPF were determined from the simulation of transient temperature programmed oxidation data in the literature. It was determined that the thermal and NO2 kinetic parameters do not change with temperature, exhaust flow rate or NO2 concentrations. However, different kinetic parameters are used for particulate oxidation in the wall and on the wall. Model results showed that oxidation of particulate in the pores of the filter wall can cause disproportionate decreases in the filter pressure drop with respect to particulate mass. The wall oxidation model along with the particulate cake filtration model were developed to model the sudden and rapid decreases in pressure drop across the CPF. The particulate cake and wall filtration models result in higher particulate filtration efficiencies than with just the wall filtration model, with overall filtration efficiencies of 98-99% being predicted by the model. The pre-exponential factors for oxidation by NO2 did not change with temperature or NO2 concentrations because of the NO2 wall production model. In both CPF-only and CCRT ® configurations, the model showed NO2 and layer I to be the dominant means and dominant physical location of particulate oxidation respectively. However, at temperatures of 280 °C, NO2 is not a significant oxidizer of particulate matter, which is in agreement with studies in the literature. The model showed that 8.6 and 81.6% of the CPF-inlet particulate matter was oxidized after 5 hours at 20 and 75% load in CCRT® configuration. In CPF-only configuration at the same loads, the model showed that after 5 hours, 4.4 and 64.8% of the inlet particulate matter was oxidized. The increase in NO2 concentrations across the DOC contributes significantly to the oxidation of particulate in the CPF and is supplemented by the oxidation of NO to NO2 by the catalyst in the CPF, which increases the particulate oxidation rates. From the model, it was determined that the catalyst in the CPF modeslty increases the particulate oxidation rates in the range of 4.5 – 8.3% in the CCRT® configuration. Hence, the catalyst loading in the CPF of the CCRT® could possibly be reduced without significantly decreasing particulate oxidation rates leading to catalyst cost savings and better engine performance due to lower exhaust backpressures.

MODELING DYNAMICS OF OZONE AND NITROGEN OXIDES AT SUMMIT, GREENLAND WITH A 1-D PROCESS-SCALE MODEL

This work presents a 1-D process scale model used to investigate the chemical dynamics and temporal variability of nitrogen oxides (NOx) and ozone (O3) within and above snowpack at Summit, Greenland for March-May 2009 and estimates surface exchange of NOx between the snowpack and surface layer in April-May 2009. The model assumes the surface of snowflakes have a Liquid Like Layer (LLL) where aqueous chemistry occurs and interacts with the interstitial air of the snowpack. Model parameters and initialization are physically and chemically representative of snowpack at Summit, Greenland and model results are compared to measurements of NOx and O3 collected by our group at Summit, Greenland from 2008-2010. The model paired with measurements confirmed the main hypothesis in literature that photolysis of nitrate on the surface of snowflakes is responsible for nitrogen dioxide (NO2) production in the top ~50 cm of the snowpack at solar noon for March – May time periods in 2009. Nighttime peaks of NO2 in the snowpack for April and May were reproduced with aqueous formation of peroxynitric acid (HNO4) in the top ~50 cm of the snowpack with subsequent mass transfer to the gas phase, decomposition to form NO2 at nighttime, and transportation of the NO2 to depths of 2 meters. Modeled production of HNO4 was hindered in March 2009 due to the low production of its precursor, hydroperoxy radical, resulting in underestimation of nighttime NO2 in the snowpack for March 2009. The aqueous reaction of O3 with formic acid was the major sync of O3 in the snowpack for March-May, 2009. Nitrogen monoxide (NO) production in the top ~50 cm of the snowpack is related to the photolysis of NO2, which underrepresents NO in May of 2009. Modeled surface exchange of NOx in April and May are on the order of 1011 molecules m-2 s-1. Removal of measured downward fluxes of NO and NO2 in measured fluxes resulted in agreement between measured NOx fluxes and modeled surface exchange in April and an order of magnitude deviation in May. Modeled transport of NOx above the snowpack in May shows an order of magnitude increase of NOx fluxes in the first 50 cm of the snowpack and is attributed to the production of NO2 during the day from the thermal decomposition and photolysis of peroxynitric acid with minor contributions of NO from HONO photolysis in the early morning.

The (2 + 1)-d U (1) quantum link model masquerading as deconfined criticality

The (2 + 1)-d U(1) quantum link model is a gauge theory, amenable to quantum simulation, with a spontaneously broken SO(2) symmetry emerging at a quantum phase transition. Its low-energy physics is described by a (2 + 1)-d RP(1) effective field theory, perturbed by an SO(2) breaking operator, which prevents the interpretation of the emergent pseudo-Goldstone boson as a dual photon. At the quantum phase transition, the model mimics some features of deconfined quantum criticality, but remains linearly confining. Deconfinement only sets in at high temperature.

Proclamation: Im Nachhange zu dem Proclam Sr. Durchlaucht des Herrn Feldmarschalls Fürsten zu Windisch-Grätz vom 1. d. M., und auf hochdessen Befehl wird von Seite des Stadt-Commando Folgendes kund gemacht: Bei der am 7. October verübten Plünderung ...

Welsch (Projektbearbeiter): Aufruf zur Rückgabe der am 7. Oktober 1848 aus dem Wiener Zeughaus geraubten Gegenstände und Warnung, die anläßlich von Hausdurchsuchungen festgestellten Besitzer dieses Raubguts nach dem Militärgesetz als Hehler zu bestrafen

Cálculo de estructuras continuas: V. 1. Métodos generales : estructuras 1-D y 2-D

Estas notas, que se publican en dos volúmenes, surgen como resultado de las clases de doctorado que, durante el curso académico 1979-80, impartió Avelino Samartín en la Escuela Técnica Superior de Ingenieros de Caminos, Canales y Puertos de la Universidad de Santander. El objetivo del curso era ambicioso ya que se intentaban presentar, de un modo panorámico, los distintos procedimientos analíticos y semianalíticos de Cálculo de Estructuras así como su aplicación al análisis efectivo de diferentes casos prácticos: vigas, placas y láminas. La publicación que se presenta es el volumen uno, que corresponde a la primera parte del curso, referente a los métodos generales de cálculo y su aplicación a casos sencillos : estructuras 1-D y 2-D. También se incluye, en el capítulo 5, una combinación natural de elementos 2-D - laja y placa-, correspondiente a la lámina plegada. Se deja para un segundo volumen el estudio de otras estructuras laminares específicas, así como la introducción a la teoría general de láminas. A lo largo del curso -y en estas notas se refleja- se ha intentado mostrar la identidad de la metodología existente en todo el cálculo estructural , desde la estructura más simple -columna- a la más compleja -lámina-, tanto en su planteamiento como en su resolución. Con esta publicación se desea -aparte de cubrir un evidente vacío bibliográfico, en nuestra lengua, sobre el tema- impulsar el uso de los diferentes métodos analíticos que actualmente existen y que, por causas bien conocidas - facilidad de computación - han sido, en opinión de los autores, inmerecidamente relegados al olvido, cuando podrían, muchas veces, sustituir , o al menos complementar, otras técnicas numéricas más potentes.

Some consistent finite element formulations of 1-D beam models: a comparative study

A consistent Finite Element formulation was developed for four classical 1-D beam models. This formulation is based upon the solution of the homogeneous differential equation (or equations) associated with each model. Results such as the shape functions, stiffness matrices and consistent force vectors for the constant section beam were found. Some of these results were compared with the corresponding ones obtained by the standard Finite Element Method (i.e. using polynomial expansions for the field variables). Some of the difficulties reported in the literature concerning some of these models may be avoided by this technique and some numerical sensitivity analysis on this subject are presented.