Avaliação da atividade antimicrobiana de sistemas emulsionados contendo óleos naturais para o tratamento de infecções cutâneas

Natural oils have shown a scientific importance due to its pharmacological activity and renewable character. The copaiba (Copaifera langsdorffii) and Bullfrog (Rana catesbeiana Shaw) oils are used in folk medicine particularly because the anti-inflammatory and antimicrobial activities. Emulsion could be eligible systems to improve the palatability and fragrance, enhance the pharmacological activities and reduce the toxicological effects of these oils. The aim of this work was to investigate the antimicrobial activity of emulsions based on copaiba (resin-oil and essential-oil) and bullfrog oils against fungi and bacteria which cause skin diseases. Firstly, the essential oil was extracted from copaiba oil-resin and the oils were characterized by gas chromatography coupled to a mass spectrometry (GC-MS). Secondly, emulsion systems were produced. A microbiological screening test with all products was performed followed (the minimum inhibitory concentration, the bioautography method and the antibiofilm determination). Staphylococcus aureus, S. epidermidis, Pseudomonas aeruginosa, Candida albicans, C. parapsilosis, C. glabrata, C. krusei and C. tropicalis American Type Culture Collection (ATCC) and clinical samples were used. The emulsions based on copaiba oil-resin and essential oil improved the antimicrobial activity of the pure oils, especially against Staphylococcus e Candida resistant to azoles. The bullfrog oil emulsion and the pure bullfrog oil showed a lower effect on the microorganisms when compared to the copaiba samples. All the emulsions showed a significant antibiofilm activity by inhibiting the cell adhesion. Thus, it may be concluded that emulsions based on copaiba and bullfrog oils are promising candidates to treatment of fungal and bacterial skin infections

Efeito da adição de óleos mineral e vegetal a acaricidas no controle do ácaro-da-leprose dos citros Brevipalpus phoenicis (Geijskes) (Acari: Tenuipalpide)

Com a finalidade de esclarecer os efeitos da adição de óleo vegetal e mineral aos acaricidas foi conduzido um ensaio de campo em 1994 no município de Viradouro, SP, utilizando-se de Assist, Triona e Natur'l Óleo, na dosagem de 500 mL por 100 litros de água, adicionados aos acaricidas: pyridaben nas formulações 200 CE e 750 PM, nas dosagens de 75 mL e 20 g; propargite 720 CE a 100 mL; óxido de fenbutatina 500 SC a 80 mL e cyhexatin 500 PM a 50 g. O delineamento estatístico adotado foi o de blocos casualizados. As aplicações foram feitas com pulverizador tipo pistola. Após a preparação da calda, foi determinado o pH. Empregou-se máquina de varredura e microscópio estereoscópico para as avaliações da população acarina. A adição de Natur'l Óleo pode afetar negativamente a eficiência do pyridaben 200 CE e 750 PM e cyhexatin 500 PM, no controle do ácaro-da-leprose. Triona e Assist não afetaram as eficiências dos acaricidas testados. Pelo índice de iodo, mediu-se o grau de insaturação das misturas dos acaricidas com Natur'l Óleo, concluindo-se que houve incorporação das moléculas dos acaricidas pelas ligações insaturadas do óleo; porém, isto não explica o diferente comportamento dos produtos no controle do ácaro da leprose dos citros.

Efeito do uso de óleos vegetais, associados ou não a inseticida, no controle de bemisia tabaci (gennadius, 1889) e thrips tabaci (lindeman, 1888), em feijoeiro, na época das águas

The objective of this experiments was evaluate the control of Bemisia tabaci and Thrips tabaci, through the use of plant oils associated or not to insecticide in bean plants, besides verifying the consequences on yield. The experiment was carried out in the period of rainy seasons, by utilizing Carioca variety. The statistical design was the randomized blocks, by employing a 6x2 factorial scheme ( plant oil versus insecticide), totalizing 12 treatments and four replications. It was concluded thet application of plant oils without insecticide can be utilized on the control of the B. tabaci biotipo B, since their population and the symptoms of golden mosaic was similar to the treatment plant oils plus insecticide; among the plant oils Agrex (R) plant oil promoted a higher control of white fly. For T. tabaci the application of plant oil associated to insecticide provide with a smaller population index when compared to the treatments without this association. The yield was not affected by the population of B. tabaci biotipo B and T. tabaci when plant oils were utilized, associated or not to the insecticide.

Efeito da adição de óleos ao acaricida cyhexatin sobre o ácaro Brevipalpus phoenicis e na retenção de calda por folhas de citros

A adição de óleos à calda de pulverização, muitas vezes, é utilizada a campo sem o adequado conhecimento sobre a absorção do produto fitossanitário pelo alvo, retenção de calda e até mesmo sobre a praga e a cultura. O objetivo do trabalho foi avaliar o efeito da adição de óleos ao acaricida cyhexatin sobre o ácaro Brevipalpus phoenicis e na retenção de calda por folhas de citros. Avaliou-se a mortalidade de ácaros, utilizando-se de frutos de laranja com uma arena circundada com cola entomológica para confinar os ácaros. Adotou-se o delineamento inteiramente casualizado, em esquema fatorial, constituído pelos fatores: duas formulações de cyhexatin (WG e SC), dois tipos de óleo (mineral e vegetal) e duas concentrações dos óleos (0,5 e 1,0%), e mais dois tratamentos adicionais (acaricidas não adicionados de óleo) e uma testemunha sem aplicação. A aplicação dos produtos foi realizada sobre frutos de laranja até além do ponto de escorrimento. Logo após a aplicação, transferiram-se 10 ácaros B. phoenicis para cada fruto.A contagem dos ácaros vivos, mortos e retidos na barreira adesiva foi realizada um dia após a aplicação. Para a determinação da quantidade de calda retida, utilizaram-se folhas de laranjeira, que foram pulverizadas até além do ponto de escorrimento, adotando-se os mesmos tratamentos e o delineamento estatístico mencionados para a avaliação da mortalidade de ácaros, com exceção da testemunha sem aplicação. Determinou-se a massa de líquido retido após a aplicação dos produtos por folha, com auxílio de balança de precisão. Verificou-se que um dia após a aplicação dos produtos, todos os tratamentos apresentaram mortalidade de B. phoenicis acima de 99%. Dessa forma, a adição de óleo, seja mineral, seja vegetal, ao acaricida cyhexatin não afetou a eficácia biológica deste acaricida nas formulações SC e WG. A maior fuga de B. phoenicis para a barreira de cola foi verificada nos tratamentos com adição de óleos, em comparação ao cyhexatin aplicado isoladamente. A adição de óleo, seja mineral, seja vegetal, ao cyhexatin na calda de pulverização reduziu a quantidade máxima de líquido retido pelas folhas de citros, podendo contribuir para a redução da quantidade de calda necessária para uma boa cobertura da planta.

Ação de tinturas e óleos essenciais de plantas medicinais sobre o crestamento bacteriano comum do feijoeiro e na produção de proteínas de indução de resistência

A exploração da atividade biológica de compostos secundários presentes nas tinturas ou em óleos essenciais de plantas podem representar, ao lado da indução de resistência, mais uma forma potencial de controle de doenças em plantas cultivadas. O presente trabalho objetivou avaliar o potencial de tinturas de Lippia alba, Lippia sidoides, Mikania glomerata, Equisetum sp. e Hedera helix e óleos essenciais de Rosmarinus officinalis e Cinnamomum zeylanicum nas atividades in vitro, in vivo e na produção de proteínas na indução de resistência, em plantas de feijão vagem cultivar Bragança. Os resultados obtidos demonstraram que as tinturas de L. alba e L. sidoides e os óleos essenciais (R. officinalis e C. zeylanicum) apresentaram atividade in vitro aos isolados de Xanthomonas axonopodis pv. phaseoli. Todas as tinturas ensaiadas apresentaram menores valores do progresso da doença (AACPD), em relação à testemunha, merecendo destaque a tintura de L. alba, que estavam correlacionadas com os maiores teores de polifenoloxidase, peroxidase e proteínas solúveis totais, evidenciando uma possível indução de resistência. Os óleos essenciais não apresentaram diferença na AACPD e nem na indução de proteínas.

Tensão superficial estática de soluções aquosas com óleos minerais e vegetais utilizados na agricultura

O trabalho teve como objetivo avaliar a tensão superficial estática de soluções aquosas com formulações de óleos minerais e vegetais emulsionáveis utilizados como adjuvantes na agricultura. Os óleos minerais e vegetais, quando adicionados aos produtos fitossanitários, podem imprimir características desejáveis à calda de pulverização, como reduzir a tensão superficial em soluções aquosas, possibilitar maior contato da calda com a superfície vegetal ou reduzir o potencial de deriva durante as pulverizações. Foram testados os seguintes produtos comerciais: óleos minerais (Assist, Attach, Dytrol, Iharol, Mineral Oil, Spinner, Sunspray-E e Triona) e óleos vegetais (Agrex'oil Vegetal, Crop Oil, Natur'l Óleo, Óleo Vegetal Nortox e Veget Oil), todos com registro de uso na agricultura. A tensão superficial das soluções aquosas foi avaliada em 11 concentrações para cada produto (0,025; 0,05; 0,1; 0,25; 0,5; 0,75; 1,0; 1,5; 2,0; 2,5 e 3,0% v/v). Essa propriedade dos óleos minerais e dos óleos vegetais foi estimada medindo-se a massa das gotas formadas na extremidade de uma bureta. Ao conjunto de dados obtidos para cada produto, na avaliação da tensão superficial, foram determinadas as análises de variância e de regressão, ajustando-se os dados ao Modelo de Mitscherlich. Entre os óleos minerais, destacaram-se os produtos: Assist, Dytrol, Iharol e Mineral Oil por apresentarem as menores tensões superficiais mínimas estimadas pelo Modelo, respectivamente, 29,255; 28,442; 26,097 e 28,584 mN m-1. Os óleos vegetais que apresentaram os menores valores de tensão superficial mínima estimados pelo Modelo, foram: Agrex' oil Vegetal (27,716 mN m-1), Natur'l óleo (28,216 mN m-1), Veget Oil (27,308 mN m-1) e Crop Oil (29,964 mN m-1).

Constribuição técnica de um sistema de emulsão inversa a base de óleos vegetais para fluidos de perfuração

The developments in formulating drilling fluids to apply in petroleum fields are based on new technologies and environmental challenges, where the technical performance of a developed drilling fluid is used to produce a minimum environmental impact, showing great economy in costs. It is well known that the potential use of oil-based drilling fluids is limited because these fluids when discharged in the sea do not disperse as much as water-based ones and may form waterproof films in the seabed, having a profound effect on plants and animals living in this environment. The current works have been made in investigating fluids called pseudofluids, which are synthetic ester-based, n-paraffin-based and other fluids formed from inverse emulsion. In this research the principal parameters involved in inverse emulsion process were studied, in laboratory scale, using esters as main component. Others commercial drilling fluids were used as comparative samples, as well as samples from laboratory and field where these drilling fluids are being applied. Concentrations of emulsifier and organophilic clay, which are viscosity donor, were varied to verify the influence of these parameters, in different oil/water ratios (55/45, 60/40, 65/35, 70/30, and 75/25). The salt concentration (NaCl) is an indicative parameter of stability and activity of an esterbased fluid. In this research the salt concentration was varied in 10,000, 20,000, and 50,000 ppm of NaCl. Some rheological properties of the produced fluids were studied, such as: initial gel, plastic viscosity, yield point, and apparent viscosity. Through the obtained rheological measures, the existence of two systems could be verified: fluid and flocculated. It could be noticed that the systems were influenced, directly, by the oil/water ratio and emulsifier, organophilic clay and NaCl concentrations. This study showed the viability to use an ester obtained from a regional vegetable product babaçu coconut oil to obtain an efficient and environmental safe drilling fluid

Remoção do cobre de efluente galvânico aplicando tensoativos derivado de óleos vegetais

Copper is one of the most used metals in platingprocesses of galvanic industries. The presence of copper, a heavy metal, in galvanic effluents is harmful to the environment.The main objective of this researchwas the removal ofcopperfromgalvanic effluents, using for this purpose anionic surfactants. The removal process is based on the interaction between the polar head group of the anionic surfactant and the divalent copper in solution. The surfactants used in this study were derived from soybean oil (OSS), coconut oil (OCS), and sunflower oil (OGS). It was used a copper synthetic solution (280 ppm Cu+2) simulating the rinse water from a copper acid bath of a galvanic industry. It were developed 23and 32 factorial designs to evaluate the parameters that have influence in theremoval process. For each surfactant (OSS, OCS, and OGS), the independent variables evaluated were: surfactant concentration (1.25 to 3.75 g/L), pH (5 to 9) and the presence of an anionic polymer (0 to 0.0125 g/L).From the results obtained in the 23 factorial design and in the calculus for estimatingthe stoichiometric relationship between surfactants and copper in solution, it were developed new experimental tests, varying surfactant concentration in the range of 1.25 to 6.8 g/L (32 factorial design).The results obtained in the experimental designs were subjected to statistical evaluations to obtain Pareto charts and mathematical modelsfor Copper removal efficiency (%). The statistical evaluation of the 23 and 32factorial designs, using saponifiedcoconut oil (OCS), presented the mathematical model that best described the copper removal process.It can be concluded that OCS was the most efficient anionic surfactant, removing 100% of the copper present in the synthetic galvanic solution

Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Extração de metais pesados de efluentes da indústria do petróleo utilizando derivados de óleos vegetais como extratantes

The study of a promising alternative for the treatment of produced water from the oil industry envisaging its reuse was the focus of this work. Millions of liters of water are generated per day, containing heavy metals in low concentrations (< 0,15 mg/L for Pb, <0,04 mg/L for Cd, <0,04 mg/L for Ni). The technology applied to extract these metals from aqueous phase was the solvent extraction and the extratants used were vegetable oils originated from coconut oil. They can be used in natural form or as derivatives, known as MAC - Mixture of Carboxílics Acids. The determination of the heavy metal con¬centrations in a complex matrix was made by using the atomic absorption spectrometry technique (AAS). On the bench tests using synthetics aqueous solutions containing metals, vegetable oils showed no power to extract the metals studied. The extractant MAC was selective for the Pb> Cd> Ni, in the concentration of 8% in the same organic phase. In this condition, the lower efficiency of extraction obtained was 92% for the Pb, 69% for the Cd, in the range of pH ranging from 6 to 8. An experimental planning was conducted for continuous tests. The device used was called MDIF Misturador-Decantador à Inversão de Fases and the aqueous phase was produced water from Pólo Indutrial de Guamaré/RN . No correlation between the studied variables (concentration of metal, concentration of extratant and agitation in the mixing chamer) could be obtained, because of possible factors which occurred as: variation in the composition of the studied sample, phenomena of precipitation and complexation of metals in the reservoir of feed, solubility of extratant

Formulação de novos combustíveis base diesel: avaliação de desempenho e emissões

The industry, over the years, has been working to improve the efficiency of diesel engines. More recently, it was observed the need to reduce pollutant emissions to conform to the stringent environmental regulations. This has attached a great interest to develop researches in order to replace the petroleum-based fuels by several types of less polluting fuels, such as blends of diesel oil with vegetable oil esters and diesel fuel with vegetable oils and alcohol, emulsions, and also microemulsions. The main objective of this work was the development of microemulsion systems using nonionic surfactants that belong to the Nonylphenols ethoxylated group and Lauric ethoxylated alcohol group, ethanol/diesel blends, and diesel/biodiesel blends for use in diesel engines. First, in order to select the microemulsion systems, ternary phase diagrams of the used blends were obtained. The systems were composed by: nonionic surfactants, water as polar phase, and diesel fuel or diesel/biodiesel blends as apolar phase. The microemulsion systems and blends, which represent the studied fuels, were characterized by density, viscosity, cetane number and flash point. It was also evaluated the effect of temperature in the stability of microemulsion systems, the performance of the engine, and the emissions of carbon monoxide, nitrogen oxides, unburned hydrocarbons, and smoke for all studied blends. Tests of specific fuel consumption as a function of engine power were accomplished in a cycle diesel engine on a dynamometer bench and the emissions were evaluated using a GreenLine 8000 analyzer. The obtained results showed a slight increase in fuel consumption when microemulsion systems and diesel/biodiesel blends were burned, but it was observed a reduction in the emission of nitrogen oxides, unburned hydrocarbons, smoke index and f sulfur oxides

Integração dos processos de flotação e foto-fenton para redução de óleos e graxas de água produzida em campos de petróleo

During production of oil and gas, there is also the production of an aqueous effluent called produced water. This byproduct has in its composition salts, organic compounds, gases and heavy metals. This research aimed to evaluate the integration of processes Induced Air Flotation (IAF) and photo-Fenton for reducing the Total Oils and Greases (TOG) present in produced water. Experiments were performed with synthetic wastewater prepared from the dispersion of crude oil in saline solution. The system was stirred for 25 min at 33,000 rpm and then allowed to stand for 50 min to allow free oil separation. The initial oil concentration in synthetic wastewater was 300 ppm and 35 ppm for the flotation and the photo-Fenton steps, respectively. These values of initial oil concentration were established based on average values of primary processing units in Potiguar Basin. The processes were studied individually and then the integration was performed considering the best experimental conditions found in each individual step. The separation by flotation showed high removal rate of oil with first-order kinetic behavior. The flotation kinetics was dependent on both the concentration and the hydrophilic-lipophilic balance (HLB) of the surfactant. The best result was obtained for the concentration of 4.06.10-3 mM (k = 0.7719 min-1) of surfactant EO 2, which represents 86% of reduction in TOG after 4 min. For series of surfactants evaluated, the separation efficiency was found to be improved by the use of surfactants with low HLB. Regarding the TOG reduction step by photo-Fenton, the largest oil removal reached was 84% after 45 min of reaction, using 0.44 mM and 10 mM of ferrous ions and hydrogen peroxide, respectively. The best experimental conditions encountered in the integrated process was 10 min of flotation followed by 45 min of photo-Fenton with overall TOG reduction of 99%, which represents 5 ppm of TOG in the treated effluent. The integration of processes flotation and photo-Fenton proved to be highly effective in reducing TOG of produced water in oilfields

Síntese e caracterização de materiais nanoporosos para pirólise catalítica de óleos pesados

The present work reports the study of nanoporous structures, aiming at their use in research directed to the current demand of the petroleum industry to value heavy oil. Initially, two ways were chosen for the synthesis of porous structures from the molecular sieves of type Si-MCM-41. In the first way, the structure MCM-41 is precursory for heteroatom substitutes of silicon, generating catalyst of the type Al-MCM-41 from two different methods of incorporation of the metal. This variation of the incorporation method of Aluminum in the structure of Si-MCM-41 was carried out through the conventional procedure, where the aluminum source was incorporated to the gel of synthesis, and the procedure post-synthesis, where the Aluminum source was incorporated in catalyst after the synthesis of Si-MCM-41. In the second way, the MCM-41 acts as a support for growth of nanocrystals of zeolite embedded in their mesoporous, resulting in hybrid MCM-41/ZSM-5 catalyst. A comparative analysis was carried through characterizations by XRD, FTIR, measures of acidity through n-butylamine adsorption for TGA, SEM-XRF and N2 adsorption. Also crystalline aluminosilicate with zeolitic structure MFI of type ZSM-5 was synthesized without using organic templates. Methodologies to the preparation of these materials are related by literature using conventionally reactants that supply oxides of necessary silicon and aluminum, as well as a template agent, and in some cases co-template. The search for new routes of preparation for the ZSM-5 aimed at, above all, the optimization of the same as for the time and the temperature of synthesis, and mainly the elimination of the use of organic templates, that are material of high cost and generally very toxic. The current study is based on the use of the H2O and Na+ cations playing the role of structural template and charge compensation in the structure. Characterizations by XRD, FTIR, SEM-XRF and N2 adsorption were also conducted for this material in order to compare the samples of ZSM-5 synthesized in the absence of template and those used industrially and synthesized using structuring

Síntese de catalisadores nanoporosos na ausência total e parcial de direcionadores orgânicos para pirólise catalítica de óleos pesados e intermediários

The processing of heavy oil produced in Brazil is an emergency action and a strategic plan to obtain self-sufficiency and economic surpluses. Seen in these terms, it is indispensable to invest in research to obtain new catalysts for obtaining light fraction of hydrocarbons from heavy fractions of petroleum. This dissertation for the degree of Doctor of Philosophy reports the materials preparation that combine the high catalytic activity of zeolites with the greater accessibility of the mesoporosity, more particularly the HZSM-5/MCM-41 hybrid, done by synthesis processes with less environmental impact than conventional ones. Innovative methodologies were developed for the synthesis of micro-mesoporous hybrid material by dual templating mechanism and from crystalline zeolitic aluminosilicate in the absence of organic template. The synthesis of hybrid with pore bimodal distribution took place from one-single organic directing agent aimed to eliminate the use of organic templates, acids of any kind or organic solvents like templating agent of crystalline zeolitic aluminosilicate together with temperature-programmed microwave-assisted, making the experimental procedures of preparation most practical and easy, with good reproducibility and low cost. The study about crystalline zeolitic aluminosilicate in the absence of organic template, especially MFI type, is based on use of H2O and Na+ cation playing a structural directing role in place of an organic template. Advanced characterization techniques such as X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Highresolution Transmission Electron Microscopy (HRTEM), Adsorption of N2 and CO2, kinetic studies by Thermogravimetric Analysis (TGA) and Pyrolysis coupled to Gas Chromatography/Mass Spectrometry (Pyrolysis-GC/MS) were employed in order to evaluate the synthesized materials. Achieve the proposed objectives, has made available a set of new methodologies for the synthesis of zeolite and hybrid micro-mesoporous material, these suitable for catalytic pyrolysis of heavy oils aimed at producing light fraction

Hematologia de tilápias-do-nilo alimentadas com dietas com óleos vegetais e estimuladas pelo frio

O objetivo deste trabalho foi avaliar os efeitos de dietas com diferentes relações entre ácidos graxos poliinsaturados ômega-6 e ômega-3 nos parâmetros hematológicos e lipídeos plasmáticos de tilápias-do-nilo, antes e após estímulo pelo frio. Foram utilizados 320 alevinos invertidos para macho (±7,5 g), distribuídos aleatoriamente em 40 tanques (250 L) e alimentados com oito dietas: basal (sem adição de óleo), 6% de óleo de girassol (OG), 5% de OG + 1% de óleo de linhaça (OL), 4% de OG + 2% OL, 3% de OG + 3% de OL, 2% de OG + 4% de OL, 1% de OG + 5% de OL e 6% de OL. Os parâmetros hematológicos e os lipídeos plasmáticos foram determinados ao final de 85 dias de cultivo e após três dias de estímulo pelo frio. Não houve efeito das dietas sobre nenhuma das variáveis analisadas no período anterior ao estímulo. O número de leucócitos foi reduzido em peixes alimentados com a dieta 6% de OL, após estímulo pelo frio. O estímulo pelo frio provocou um declínio do estado geral de saúde, como leucopenia. Tilápias-do-nilo alimentadas com dietas com 6% de OL apresentaram menor resistência ao frio.