Integration of Torrefaction with Steam Power Plant

Torrefaction is one of the pretreatment technologies to enhance the fuel characteristics of biomass. The efficient and continuous operation of a torrefaction reactor, in the commercial scale, demands a secure biomass supply, in addition to adequate source of heat. Biorefinery plants or biomass-fuelled steam power plants have the potential to integrate with the torrefaction reactor to exchange heat and mass, using available infrastructure and energy sources. The technical feasibility of this integration is examined in this study. A new model for the torrefaction process is introduced and verified by the available experimental data. The torrefaction model is then integrated in different steam power plants to simulate possible mass and energy exchange between the reactor and the plants. The performance of the integrated plant is investigated for different configurations and the results are compared.

Biovoimalaitoksen energiatehokkuuden parantaminen ja osakuorma-ajon optimointi

Energiatehokkuus on nykyaikana yksi tärkeimmistä energiataloudellisista tekijöistä voimalaitosten sähköntuotannossa. Varsinkin yhteistuotantolaitoksissa joissa sähkö on lämpöenergian lisänä saatava sivutuote, sähkön tuotannon optimointi voi merkitä laitostalouden ja yrityksen kannalta huomattavia lisätuloja tai -säästöjä. Kaukaan Voima Oy:n biovoimalaitos on vuonna 2009 kaupalliseen käyttöön valmistunut moderni yhteistuotantolaitos, joka sijaitsee Lappeenrannassa UPM Kaukas sellutehtaan tehdasalueella. Voimalaitos tuottaa kaukolämpöä ja sähköä Lappeenrannan kaupungille sekä prosessihöyryä ja sähköä UPM Kaukaan tehtaille. Tämän työn tavoitteena on tarkastella biovoimalaitoksen omakäyttösähkön kulutusta kuukausitasolla verrattuna laitoksella tuotettavan höyryn määrään sekä etsiä voimalaitokselta kohteita, joiden omakäyttösähkön kulutusta voidaan vähentää vaikuttamatta höyryntuotantoon ja näin parantaa laitoksen energiatehokkuutta ja hyötysuhdetta. Työ rajataan käsittelemään voimalaitoksen apulaitteiden ja -järjestelmien omakäyttösähkön kulutusta. Työssä tarkastellaan vuodenaikojen vaihtelun ja kaukolämmön sekä prosessihöyryn tarpeen muutoksen vaikutusta voimalaitoksen ajomalliin sekä höyryntuotannon ja omakäyttösähkön kulutuksen suhteisiin. Työssä esiin nousseiden kohteiden potentiaaliset sähköenergian säästöt ovat noin 2500 MWh vuodessa joka tarkoittaa keskimäärin 3,7 % vähennystä voimalaitoksen kuukausittaiseen omakäyttösähkön kulutukseen. Kohteet eivät käytännössä vaadi minkaanlaista investointirahaa, vaan uusia ajojärjestelyitä. Keskeisimmiksi säästökohteiksi valikoitui laitoksen pumppausjärjestelmien paineenalennukset.

FOOD PREFERENCE AND CONSUMPTION OF AQUATIC MACROPHYTES SUBMERGED BY SNAIL Pomacea canaliculata

ABSTRACTThe objective of this study was to evaluate the consumption potential, food preference and use of snail Pomacea canaliculata as a biocontrol agent of four submerged aquatic macrophytes (Ceratophyllumdemersum, Egeriadensa, Egerianajas and Hydrilla verticillata). Two experiments were performed. In the first experiment, the introduction of a snail took place and 10 grams of each macrophyte in plastic containers with 1 liter of water. The assessments of consumption by the snail were performed at each 48 hours, during 12 days. The second experiment was performed in 600 liters microcosms containing five snails in each experimental unit. Fifty grams of each macrophyte were offered the snails at the same time, adding the same amounts after seven, 14, 21 and 30 days. On both trials, the most consumed macrophyte by the P.canaliculata was H.verticillata (7.64 ± 1.0 g 48 h and 50 ± 0.18 g) respectively, significantly differing from the others. However, in the absence of H.verticilata, E.najas and E.densa were consumed. The preference of P.canaliculata for H.verticillata is very interesting, because this plant is exotic and problematic in Brazil, and the snail is one more tool for biological management of submerged aquatic macrophyte H.verticillata.

Influence of body mass and environmental oxygen tension on the oxygen consumption rates of an enteropneust, Glossobalanus crozieri

The present study deals with a species of enteropneust, Glossobalanus crozieri, focusing on two aspects of its respiration: a) oxygen consumption and body mass, and b) the influence of environmental oxygen tension on the respiratory rate. Preliminarily, the body water content was shown to be 85% of the whole body weight. The regression coefficient of the oxygen consumption on the wet body mass (0.578) seems to agree with the view that in enteropneusts respiration is mainly cutaneous. The respiratory rate was significantly reduced at O2 tensions from 76 mmHg downwards, suggesting conformity rather than regulation

Concentration of hydrogen peroxide and improving its energy efficiency

Distillation is a unit operation of process industry, which is used to separate a liquid mixture into two or more products and to concentrate liquid mixtures. A drawback of the distillation is its high energy consumption. An increase in energy and raw material prices has led to seeking ways to improve the energy efficiency of distillation. In this Master's Thesis, these ways are studied in connection with the concentration of hydrogen peroxide at the Solvay Voikkaa Plant. The aim of this thesis is to improve the energy efficiency of the concentration of the Voikkaa Plant. The work includes a review of hydrogen peroxide and its manufacturing. In addition, the fundamentals of distillation and its energy efficiency are reviewed. An energy analysis of the concentration unit of Solvay Voikkaa Plant is presented in the process development study part. It consists of the current and past information of energy and utility consumptions, balances, and costs. After that, the potential ways to improve the energy efficiency of the distillation unit at the factory are considered and their feasibility is evaluated technically and economically. Finally, proposals to improve the energy efficiency are suggested. Advanced process control, heat integration and energy efficient equipment are the most potential ways to carry out the energy efficient improvements of the concentration at the Solvay Voikkaa factory. Optimization of the reflux flow and the temperatures of the overhead condensers can offer immediate savings in the energy and utility costs without investments. Replacing the steam ejector system with a vacuum pump would result in savings of tens of thousands of euros per year. The heat pump solutions, such as utilizing a mechanical vapor recompression or thermal vapor recompression, are not feasible due to the high investment costs and long pay back times.

Functional, Social and Emotional Values as Determinants of Environmentally Responsible Media Consumption

The primary purpose of this research is to develop an enhanced understanding of how consumption values influence environmentally responsible consumption of print and digital media. Theoretical elaboration considers the associations of functional, social and emotional consumption values, green consumer segmentation and media consumption. Additionally, the purpose is to identify consumer perceptions of print and digital media’s environmental responsibility. Empirical analysis was based on qualitative interviews with a sample of 20 Finnish consumers categorized in two segments: young adults and middle aged consumers. Primary data collection was conducted through individual, semi-structured interviews. To analyze the respondents’ approach on the topic, the interviews disclosed themes of media consumption, perceived environmental friendliness of media, norms of behavior and consumers’ general consumption patterns. The results implicate functional value dominated the consumption decision-making process both in a general level and in media consumption. In addition to functional value, environmental responsibility does provide consumers with both emotional and social values. Analysis on perceived environmental responsibility of media demonstrated consumers generally perceive digital media as an environmentally responsible alternative because it does not create physical paper waste. Nevertheless, the perceptions of environmental responsibility and media consumption patterns lacked a consistent connection. Though, both theory and empirical results indicated an average consumer lacks a comprehensive understanding of digital and print media’s life-cycle and hence their environmental advantages and disadvantages.

Comparison of energy balances of steam explosion and torrefaction technologies

The present study introduce two pretreatment technologies which are torrefaction and steam explosion, and compare energy balance for both technologies to investigate and compare the use of these technologies to improve pelletization. In this research, torrefaction and steam explosion pretreatments were accomplished on the mixed small diameter wood (70%) with moisture content of 40 %, and logging residues (30%) with moisture content of 45 % at temperature 230 ̊C, and treatment duration 10 min. Competing methods were evaluated, and the results showed higher volumetric energy for steam explosion pellet than torrefied pellet.

Oxygen consumption of rats with broad intestinal resection

The study was performed to investigate possible alterations in oxygen consumption in an animal model with broad intestinal resection. Oxygen consumption and the thermal effect of a short meal were measured in rats subjected to short bowel syndrome. Four groups of rats were used. Group I was the control group, group II was sham operated, group III was submitted to 80% jejunum-ileum resection, and group IV was submitted to 80% jejunum-ileum resection with colon interposition. Ninety days after surgery, oxygen consumption was measured over a period of 6 h with the animals fasted overnight. The thermal effect of feeding was determined in another session of oxygen consumption measurement in animals fasted for 12 h. A 12-kcal meal was then introduced into the animal chamber and oxygen consumption was measured for a further 4 h. No differences in fasting oxygen consumption or in the thermal effect of the meal were detected among the groups studied. It is concluded that short bowel syndrome does not affect the overall energy expenditure of rats.

Low ethanol consumption increases insulin sensitivity in Wistar rats

Several human studies suggest that light-to-moderate alcohol consumption is associated with enhanced insulin sensitivity, but these studies are not free of conflicting results. To determine if ethanol-enhanced insulin sensitivity could be demonstrated in an animal model, male Wistar rats were fed a standard chow diet and received drinking water without (control) or with different ethanol concentrations (0.5, 1.5, 3, 4.5 and 7%, v/v) for 4 weeks ad libitum. Then, an intravenous insulin tolerance test (IVITT) was performed to determine insulin sensitivity. Among the ethanol groups, only the 3% ethanol group showed an increase in insulin sensitivity based on the increase of the plasma glucose disappearance rate in the IVITT (30%, P<0.05). In addition, an intravenous glucose tolerance test (IVGTT) was performed in control and 3% ethanol animals. Insulin sensitivity was confirmed in 3% ethanol rats based on the reduction of insulin secretion in the IVGTT (35%, P<0.05), despite the same glucose profile. Additionally, the 3% ethanol treatment did not impair body weight gain or plasma aspartate aminotransferase and alanine aminotransferase activities. Thus, the present study established that 3% ethanol in the drinking water for 4 weeks in normal rats is a model of increased insulin sensitivity, which can be used for further investigations of the mechanisms involved.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Effect of the consumption of tomato paste on plasma prostate-specific antigen levels in patients with benign prostate hyperplasia

The consumption of tomatoes and tomato products has been associated with a reduced risk of prostate cancer. We observed a decrease of 10.77% in prostate-specific antigen (PSA) levels in patients with benign prostate hyperplasia who were submitted to daily ingestion of tomato paste. This was an experimental rather than a controlled study with a sample of 43 men ranging in age from 45 to 75 years, all with histological diagnoses of benign prostate hyperplasia and plasma PSA levels of 4-10 ng/mL. All patients received 50 g of tomato paste once a day for 10 consecutive weeks and PSA levels were analyzed before, during and after the consumption of tomato paste. ANOVA for repeated measures was used to compare PSA levels before, during and after the consumption of tomato paste. The mean ± SD PSA level was 6.51 ± 1.48 ng/mL at baseline and 5.81 ± 1.58 ng/mL (P = 0.005) after 10 weeks. Acceptance was good in 88.3, regular in 9.3, and poor in 2.3% of the patients. Dietary ingestion of 50 g of tomato paste per day for 10 weeks significantly reduced mean plasma PSA levels in patients with benign prostate hyperplasia, probably as a result of the high amount of lycopene in tomato paste. This was not a prostate cancer prevention study, but showed some action of tomato paste in prostate biology. The development of prostate cancer is typically accompanied by an increase in plasma PSA levels, thus any intervention that affects plasma PSA levels can suggest an impact in the progression of disease.

Food consumption by young adults living in Ribeirão Preto, SP, 2002/2004

There is evidence showing a close relationship between diet and the occurrence of non-communicable chronic diseases. The present study assessed food consumption in a 2002/2004 cohort of young adults born in 1978/79 in Ribeirão Preto, SP, Brazil. The composition of the habitual diet consumed by a sample of 2063 individuals aged 23-25 years was analyzed using a validated semi-quantitative food frequency questionnaire based on studies of prevention of non-communicable chronic diseases. The Dietsys software was used for dietary calculations. In terms of WHO/2003 recommendations, there was a high mean daily consumption of energy from fat (consumption: 35.4%; recommendation: 15-30%), a low mean intake of energy from carbohydrates (47.5%; 55-75%) and a low mean consumption of total fibers (15.2 g; >25 g). Mean intake of energy from fatty acids (10%; <10%) and protein (15.6%; 10-15%) was within recommended limits. When compared to the recommendations of the food pyramid adapted to the Brazilian population, adequate intake was observed only regarding the meat group (consumption: 1.9 portions; recommended: 1-2). There was a low consumption of vegetables (2.9; 4-5), fruits (1.2; 3-5), breads (3.6; 6-9), and dairy products (1.7; 3), with excessive fat and sugar intake (5.7; 1-2). We conclude that the inadequate food consumption observed in this young population may be associated with the development of excess weight and may contribute to the triggering of non-communicable chronic diseases.