Modeling, optimizing and simulating robot calibration with accuracy improvement

This work describes techniques for modeling, optimizing and simulating calibration processes of robots using off-line programming. The identification of geometric parameters of the nominal kinematic model is optimized using techniques of numerical optimization of the mathematical model. The simulation of the actual robot and the measurement system is achieved by introducing random errors representing their physical behavior and its statistical repeatability. An evaluation of the corrected nominal kinematic model brings about a clear perception of the influence of distinct variables involved in the process for a suitable planning, and indicates a considerable accuracy improvement when the optimized model is compared to the non-optimized one.

Control of a one-legged robot with energy savings

This paper presents a new strategy to control an one-legged robot aiming to reduce the energy expended by the system. To validate this algorithm, a classic method as benchmark was used. This method has been extensively validated by simulations and experimental prototypes in the literature. For simplicity reasons, the work is restricted to the two dimensional case due to simplicity reasons. This new method is compared to the classic one with respect to performance and energy expended by the system. The model consists on a springy leg, a simple body, and an actuated hinge-type hip. The new control strategy is composed of three parts, considering the hopping height, the forward speed, and the body orientation separately. The method exploits the system passive dynamics, defined as non-forced response of the system. In this case, the model is modified adding a spring to the hip. The method defines a desired leg trajectory close to the passive hip swing movement. Simulation results for both methods are analyzed and compared.

Speed Control of an Autonomous Mobile Robot: Comparison between a PID Control and a Control Using Fuzzy Logic

An Autonomous Mobile Robot battery driven, with two traction wheels and a steering wheel is being developed. This Robot central control is regulated by an IPC, which controls every function of security, steering, positioning localization and driving. Each traction wheel is operated by a DC motor with independent control system. This system is made up of a chopper, an encoder and a microcomputer. The IPC transmits the velocity values and acceleration ramp references to the PIC microcontrollers. As each traction wheel control is independent, it's possible to obtain different speed values for each wheel. This process facilities the direction and drive changes. Two different strategies for speed velocity control were implemented; one works with PID, and the other with fuzzy logic. There were no changes in circuits and feedback control, except for the PIC microcontroller software. Comparing the two different speed control strategies the results were equivalent. However, in relation to the development and implementation of these strategies, the difficulties were bigger to implement the PID control.

A Test Bed Applied Mobile Robot Navigation

It is presented a test bed applied to studies on dynamics, control, and navigation of mobile robots. A cargo ship scale model was chosen, which can be radio-controlled or operated autonomously through an embedded control system. A control program, which manages on board mission execution, is implemented on a microcontroller. Navigation is based on an electronic compass, which includes automatic compensation for pitch and roll motions. Heading control loop is based on this sensor, and on a rudder positioning system. A propulsion control system is also implemented. Typical manoeuvres as the turning test and "zig-zag", were implemented and tested. They are included on a manoeuvre library, and can be accessed independently or in combined modes. The embedded system is also in charge of signal acquisition and storing during the missions. It is possible to analyse experiments on identification of ship dynamics, control, and navigation, through the data transferred to a PC by serial communication. Navigation is going to be improved by including inertial sensors on board, and a DGPS. Preliminary tests are aimed to ship identification, and manoeuvrability, using free model tests. Future steps include extending this system for developing other mobile robots as, ROVs, AUVs, and aerial vehicles.

Experimental validation of a 3-D vision-based measurement system applied to robot calibration

One of the problems that slows the development of off-line programming is the low static and dynamic positioning accuracy of robots. Robot calibration improves the positioning accuracy and can also be used as a diagnostic tool in robot production and maintenance. A large number of robot measurement systems are now available commercially. Yet, there is a dearth of systems that are portable, accurate and low cost. In this work a measurement system that can fill this gap in local calibration is presented. The measurement system consists of a single CCD camera mounted on the robot tool flange with a wide angle lens, and uses space resection models to measure the end-effector pose relative to a world coordinate system, considering radial distortions. Scale factors and image center are obtained with innovative techniques, making use of a multiview approach. The target plate consists of a grid of white dots impressed on a black photographic paper, and mounted on the sides of a 90-degree angle plate. Results show that the achieved average accuracy varies from 0.2mm to 0.4mm, at distances from the target from 600mm to 1000mm respectively, with different camera orientations.

Experimental study applied to an industrial robot by using variable structure controllers and friction compensation

Control of an industrial robot is mainly a problem of dynamics. It includes non-linearities, uncertainties and external perturbations that should be considered in the design of control laws. In this work, two control strategies based on variable structure controllers (VSC) and a PD control algorithm are compared in relation to the tracking errors considering friction. The controller's performances are evaluated by adding an static friction model. Simulations and experimental results show it is possible to diminish tracking errors by using a model based friction compensation scheme. A SCARA robot is used to illustrate the conclusions of this paper.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Effect of age of a sorghum-sudangrass hybrid on its allelopathic action

Hybrids of Sorghum sudanensis (sudangrass) and Sorghum bicolor genotypes can produce high amounts of biomass, sorgoleone (a long chain hydroquinone), and other phytotoxic substances. Shoots and roots of a sorghum-sudangrass hybrid (cv. Trudan 8) were collected 10, 20, 30, 40, and 50 days after emergence. Four concentrations of aqueous extracts from the shoots and roots (0, 0.4, 2, and 10 g L-1, w/v) were used to treat seeds of lettuce (Lactuca sativa), tomato (Lycopersicum sculentum), purslane (Portulaca oleracea), and pigweed (Amaranthus retroflexus). Seed germination of lettuce, tomato, and pigweed was inhibited by extracts from sorghum-sudangrass shoots at 10 g L-1 when made from sorghum-sudangrass plants 20 days or less in age. Seed germination of purslane was not inhibited by any sorghum-sudangrass extract. Growth of the four species evaluated were systematically inhibited when treated with 10 g L-1 extracts from sorghum-sudangrass shoots harvested up to 10 days after emergence.

Victims’ status at international and hybrid criminal courts : victims’ status as witnesses, victim participants/civil parties and reparations claimants

Bestraffning av internationella brott vid internationella och hybrida straffrättsliga domstolar har traditionellt och huvudsakligen grundat sig på principen om retributiv (vedergällande) rättvisa och ackusatorisk process snarare än återuppbyggande rättvisa och en inkvisitorisk modell. Därav har brottsoffrens ställning vid dessa straffrättsliga domstolar begränsat sig till den som innehas av vittnen vid Tribunalen som behandlar brott som begåtts i det forna Jugoslavien (ICTY), Internationella krigsförbrytartribunalen för Rwanda (ICTR) och Specialdomstolen för Sierra Leone (SCSL). Internationella brottmålsdomstolen (ICC), å sin sida, har medfört en viktig förändring gällande brottsoffrens ställning i internationella straffrättsliga fora, vilket innebär att de från att ha betraktats endast i egenskap av vittnen nu även har en rätt att delta och lämna sina synpunkter (i egenskap av brottsofferdeltagare) samt kräva gottgörelse. Denna trend har fortsatt inom området för internationell straffrätt, vilket manifesterats vid hybridtribunaler som tillsatts efter ICC såsom Kambodjadomstolen (ECCC) vid vilken brottsoffer kan agera civilrättsliga parter och Specialdomstolen för Libanon (STL) där brottsoffer kan inneha en deltagande roll. Den föreliggande studien behandlar två huvudsakliga frågeställningar, av vilka den första lyder: Vilken ställning tillskrivs brottsoffren vid internationella domstolar och hybridtribunaler? I detta hänseende argumenterar författaren, sammanfattningsvis, för att brottsoffrens ställning vid internationella straffrättsliga domstolar och hybridtribunaler huvudsakligen tar sig uttryck på tre sätt, d.v.s. som brottsoffer i egenskap av vittnen, som brottsoffer i egenskap av deltagande brottsoffer/civilrättsliga parter samt som brottsoffer som kräver gottgörelse. Den andra frågeställningen för denna studie lyder: På vilket sätt fungerar brottsoffrens ställning som vittnen, brottsofferdeltagande/civilrättsliga parter och gottgörelsekrävande vid internationella och hybrida straffrättsliga domstolar? -------------------------------------------------------------------------------------------------------------------------------------------------- Kansainvälisten rikosten rankaiseminen kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa on perinteisesti enimmäkseen perustunut retributiivisen oikeuden ja akkusatorisen menetelmän soveltamiseen pikemmin kuin restoratiivisen oikeuden ja inkvisitorisen menetelmän soveltamiseen. Niinpä uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa on rajoittunut todistajan asemaan entisen Jugoslavian kansainvälisessä sotarikostuomioistuimessa (ICTY), Ruandan kansainvälisessä sotarikostuomioistuimessa (ICTR) ja Sierra Leonen erikoistuomioistuimessa (SCSL). Kansainvälisen rikostuomioistuimen (ICC) perustaminen on kuitenkin merkinnyt tärkeää muutosta uhrien asemaan kansainvälisen rikosoikeuden alalla siten, että kun uhrit aiemmin nähtiin vain todistajina, heillä on nyt myös mahdollisuus tuoda esiin omat näkökantansa (osallistumisoikeus) ja vaatia hyvitystä. Tämä suuntaus on jatkunut kansainvälisen rikosoikeuden alalla ICC:n jälkeen perustetuissa hybridituomioistuimissa, kuten Kambodzhan erityistuomioistuimessa (ECCC), missä uhrit voivat olla asianosaisen asemassa, sekä Libanonin erityistuomioistuimessa (STL), missä uhrit voivat osallistua prosessiin. Tämä tutkimus käsittelee kahta keskeistä kysymystä. Ensinnäkin: Mikä on rikoksen uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa? Tutkimuksessa päädytään mm. siihen, että uhrien asema kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa voi koostua pääosin kolmesta ulottuvuudesta eli uhrit todistajina, uhrit prosessiin osallistujina/asianosaisina ja uhrit hyvityksen hakijoina. Tutkimuksen toinen keskeinen kysymys on: Miten uhrien asema todistajina, prosessiin osallistujina/ asianosaisina ja hyvityksen hakijoina toimii kansainvälisissä rikostuomioistuimissa ja hybridituomioistuimissa?

Photosynthetic characteristics of hybrid and conventional rice plants as a function of plant competition

The objective of this work was to evaluate the characteristics related to the photosynthetic ability of hybrid and inbred rice varieties, as a way to assess which of the two presented higher potential to stand out under conditions of competition. The trial was set in a greenhouse in completely randomized block design and 2 x 6 factorial scheme with four replications. Factor A consisted of rice varieties (hybrid or inbred) and factor B by competition levels. Treatments consisted in maintaining one plant of either BRS Pelota (inbred) or Inov (hybrid) variety at the center of the plot, under competition with 0, 1, 2, 3, 4 or 5 plants of the variety BRS Pelota at the periphery of the experimental unit, according to the treatment. Fifty days after emergence (DAE), sub-stomatal CO2 concentration (Ci - mmol mol-1), photosynthetic rate (A - mmol m-2 s-1) and CO2 consumed (DC - mmol mol-1) were quantified, as well as shoot dry mass(SDM).Hybrid plants present higher photosynthesis capacity than inbred plants, when competing with up to 3 times its own density. When under the same competitive intensity, hybrid plants surpass the inbred. However, it should be emphasized that, when in farm condition, the lower competitive capacity with weeds often attributed to the hybrid varieties, probably is due to their lower planting density, but if weed competition is kept at low levels, hybrid rice plants may perform in the same way or usually better than inbred plants.

Energy and Dynamics of the solar agricultural robot "SolarSprayer"

The main objective of the present study was to design an agricultural robot, which work is based on the generation of the electricity by the solar panel. To achieve the proper operation of the robot according to the assumed working cycle the detailed design of the main equipment was made. By analysing the possible areas of implementation together with developments, the economic forecast was held. As a result a decision about possibility of such device working in agricultural sector was made and the probable topics of the further study were found out.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

Use of RAPD-PCR to identify true hybrid plants from crosses between closely related progenitors

RAPD-PCR molecular markers were used to identify common bean and soybean hybrid plants derived from crosses between closely related progenitors, with no apparent phenotypic differences. Primers OP-F12 and OP-0O3 were used to identify true hybrids derived from crosses between common bean cultivars Rudá (A 285) and AN 910408, and soybean cultivars Cristalina and Bossier, respectively. Each primer generated one polymorphic DNA band which was present in the male progenitor and absent in the female progenitor. As RAPD bands are normally inherited as dominant characters, the presence of these bands in the F1 plants confirmed their status.

Multivariate genetic divergence and hybrid performance of cacao (Theobroma cacao L.)

Genetic distances among cacao cultivars were calculated through multivariate analysis, using the D2 statistic, to examine racial group classification and to assess heterotic hybrids. A 5 x 5 complete diallel was evaluated. Over a five-year period (1986-1990), five cultivars of the S1 generation, pertaining to the Lower Amazon Forastero and Trinitario racial groups and 20 crosses between the corresponding S0 parents were analyzed, based upon five yield components - number of healthy and collected fruits per plant (NHFP and NCFP), wet seed weight per plant and per fruit (WSWP and WSWF), and percentage of diseased fruits per plant (PDFP). The diversity analysis suggested a close relationship between the Trinitario and Lower Amazon Forastero groups. A correlation coefficient (r) was calculated to determine the association between genetic diversity and heterosis. Genetic distance of parents by D2 was found to be linearly related to average performance of hybrids for WSWP and WSWF (r = 0.68, P < 0.05 and r = 0.76, P < 0.05, respectively). The heterotic performance for the same components was also correlated with D2, both with r = 0.66 (P < 0.05). A relationship between genetic divergence and combining ability effects was suggested because the most divergent cultivar exhibited a high general combining ability, generating the best performing hybrids. Results indicated that genetic diversity estimates can be useful in selecting parents for crosses and in assessing relationships among cacao racial groups.

Polysiloxane/PVA-glutaraldehyde hybrid composite as solid phase for immunodetections by ELISA

We developed an efficient method to prepare a hybrid inorganic-organic composite based on polyvinyl alcohol (PVA) and polysiloxane using the sol-gel disc technique. Antigen obtained from Yersinia pestis was covalently immobilized onto these discs with glutaraldehyde and used as solid phase in ELISA for antibody detection in serum of rabbits experimentally immunized with plague. Using 1.25 µg antigen per disc, a peroxidase conjugate dilution of 1:4,000 and a serum dilution of 1:200 were adequate for the establishment of the procedure. These values are similar to those used for PVA-glutaraldehyde discs, plasticized filter paper discs and the polyaniline-Dacron composite discs. This procedure is comparable to that which utilizes the adsorption of the antigen to conventional PVC plates, with the amount of antigen being one fourth that employed in conventional PVC plates (5 µg/well). In addition to the performance of the polysiloxane/PVA-glutaraldehyde disc as a matrix for immunodetection, its easy synthesis and low cost are additional advantages for commercial application.