Load Adapted Solar Thermal Combisystems - Optical Analysis and Systems Optimization

In a northern European climate a typical solar combisystem for a single family house normally saves between 10 and 30 % of the auxiliary energy needed for space heating and domestic water heating. It is considered uneconomical to dimension systems for higher energy savings. Overheating problems may also occur. One way of avoiding these problems is to use a collector that is designed so that it has a low optical efficiency in summer, when the solar elevation is high and the load is small, and a high optical efficiency in early spring and late fall when the solar elevation is low and the load is large.The study investigates the possibilities to design the system and, in particular, the collector optics, in order to match the system performance with the yearly variations of the heating load and the solar irradiation. It seems possible to design practically viable load adapted collectors, and to use them for whole roofs ( 40 m2) without causing more overheating stress on the system than with a standard 10 m2 system. The load adapted collectors collect roughly as much energy per unit area as flat plate collectors, but they may be produced at a lower cost due to lower material costs. There is an additional potential for a cost reduction since it is possible to design the load adapted collector for low stagnation temperatures making it possible to use less expensive materials. One and the same collector design is suitable for a wide range of system sizes and roof inclinations. The report contains descriptions of optimized collector designs, properties of realistic collectors, and results of calculations of system output, stagnation performance and cost performance. Appropriate computer tools for optical analysis, optimization of collectors in systems and a very fast simulation model have been developed.

TCA Evaluation : Lab Measurements, Modelling and System Simulations

The study reported here is part of a large project for evaluation of the Thermo-Chemical Accumulator (TCA), a technology under development by the Swedish company ClimateWell AB. The studies concentrate on the use of the technology for comfort cooling. This report concentrates on measurements in the laboratory, modelling and system simulation. The TCA is a three-phase absorption heat pump that stores energy in the form of crystallised salt, in this case Lithium Chloride (LiCl) with water being the other substance. The process requires vacuum conditions as with standard absorption chillers using LiBr/water. Measurements were carried out in the laboratories at the Solar Energy Research Center SERC, at Högskolan Dalarna as well as at ClimateWell AB. The measurements at SERC were performed on a prototype version 7:1 and showed that this prototype had several problems resulting in poor and unreliable performance. The main results were that: there was significant corrosion leading to non-condensable gases that in turn caused very poor performance; unwanted crystallisation caused blockages as well as inconsistent behaviour; poor wetting of the heat exchangers resulted in relatively high temperature drops there. A measured thermal COP for cooling of 0.46 was found, which is significantly lower than the theoretical value. These findings resulted in a thorough redesign for the new prototype, called ClimateWell 10 (CW10), which was tested briefly by the authors at ClimateWell. The data collected here was not large, but enough to show that the machine worked consistently with no noticeable vacuum problems. It was also sufficient for identifying the main parameters in a simulation model developed for the TRNSYS simulation environment, but not enough to verify the model properly. This model was shown to be able to simulate the dynamic as well as static performance of the CW10, and was then used in a series of system simulations. A single system model was developed as the basis of the system simulations, consisting of a CW10 machine, 30 m2 flat plate solar collectors with backup boiler and an office with a design cooling load in Stockholm of 50 W/m2, resulting in a 7.5 kW design load for the 150 m2 floor area. Two base cases were defined based on this: one for Stockholm using a dry cooler with design cooling rate of 30 kW; one for Madrid with a cooling tower with design cooling rate of 34 kW. A number of parametric studies were performed based on these two base cases. These showed that the temperature lift is a limiting factor for cooling for higher ambient temperatures and for charging with fixed temperature source such as district heating. The simulated evacuated tube collector performs only marginally better than a good flat plate collector if considering the gross area, the margin being greater for larger solar fractions. For 30 m2 collector a solar faction of 49% and 67% were achieved for the Stockholm and Madrid base cases respectively. The average annual efficiency of the collector in Stockholm (12%) was much lower than that in Madrid (19%). The thermal COP was simulated to be approximately 0.70, but has not been possible to verify with measured data. The annual electrical COP was shown to be very dependent on the cooling load as a large proportion of electrical use is for components that are permanently on. For the cooling loads studied, the annual electrical COP ranged from 2.2 for a 2000 kWh cooling load to 18.0 for a 21000 kWh cooling load. There is however a potential to reduce the electricity consumption in the machine, which would improve these figures significantly. It was shown that a cooling tower is necessary for the Madrid climate, whereas a dry cooler is sufficient for Stockholm although a cooling tower does improve performance. The simulation study was very shallow and has shown a number of areas that are important to study in more depth. One such area is advanced control strategy, which is necessary to mitigate the weakness of the technology (low temperature lift for cooling) and to optimally use its strength (storage).

Technology diffusion: analysing the diffusion of agent technologies

Despite several examples of deployed agent systems, there remain barriers to the large-scale adoption of agent technologies. In order to understand these barriers, this paper considers aspects of marketing theory which deal with diffusion of innovations and their relevance to the agents domain and the current state of diffusion of agent technologies. In particular, the paper examines the role of standards in the adoption of new technologies, describes the agent standards landscape, and compares the development and diffusion of agent technologies with that of object-oriented programming. The paper also reports on a simulation model developed in order to consider different trajectories for the adoption of agent technologies, with trajectories based on various assumptions regarding industry structure and the existence of competing technology standards. We present details of the simulation model and its assumptions, along with the results of the simulation exercises.

Sistema de produção sincronizado : uma aplicação em processos produtivos de propriedade contínuos segundo a teoria das restrições

Este trabalho de conclusão investiga o efeito da geração de estoques intermediários nos indicadores principais empregados na Teoria das Restrições (Ganho, Despesa Operacional e Inventário) em uma unidade industrial de processo produtivo de Propriedade contínuo, que emprega embalagens, matérias-primas obtidas em larga escala e cadeias logísticas de longo curso. Este tipo de indústria produz bens de consumo imediato, com pouca variabilidade, de modo “empurrado”. A principal conseqüência é a perda do sincronismo na cadeia logística, resultando em uma grande quantidade de estoques intermediários e custos crescentes, relacionados principalmente ao custo de manutenção destes estoques. Através dos cinco passos de focalização e das ferramentas lógicas da Teoria das Restrições, propõe-se uma alternativa gerencial, que inclui o algoritmo Tambor-Pulmão-Corda e insere a organização em um processo de melhoria contínua, cujos impactos são avaliados por simulação computacional. Através de técnicas estatísticas e software apropriados, constrói-se um modelo de simulação computacional baseado em dados reais de uma planta produtora de cimento. A partir deste modelo, diferentes cenários são testados, descobrindo-se a condição ótima. Chega-se a uma conclusão, considerando a mudança na política de geração de estoques intermediários e seus impactos na redução de custos e riscos.

Avaliação dos impactos de uma proposta de escalonamento de horários em um campus universitário

O trabalho apresenta uma avaliação dos prováveis impactos do escalonamento dos horários das aulas noturnas em uma Universidade. Neste trabalho foi investigada, a preferência dos usuários quanto às possíveis alterações nos horários de entrada de aulas, e os impactos do escalonamento na rede viária no entorno do campus. O trabalho envolveu a construção de diversos cenários de alterações nos horários de início das aulas. Os cenários foram construídos visando atender as preferências da população universitária e reduzir a interferência do pico de chegada de alunos no sistema viário. A avaliação dos impactos destes cenários no tráfego foi realizada através de simulação, com a utilização do modelo TSIS/NETSIM. As análises foram baseadas em dois indicadores de desempenho: a velocidade média e o tempo de atraso médio na rede.

O uso da volatilidade realizada na simulação histórica ajustada para cálculo do VaR

O presente trabalho propõe para o cálculo VaR o modelo de simulação histórica, com os retornos atualizados pela volatilidade realizada calculada a partir de dados intradiários. A base de dados consiste de cinco ações entre as mais líquidas do Ibovespa de distintos segmentos. Para a metodologia proposta utilizamos duas teorias da literatura empírica – simulação histórica ajustada e volatilidade realizada. Para análise e verificação do desempenho da metodologia proposta utilizamos o Teste de Kupiec e o Teste de Christoffersen.

A Modular and digitally programmable interface based on band-pass sigma-delta modulator for mixed-signal systems-on-chip

The focus of this thesis is to discuss the development and modeling of an interface architecture to be employed for interfacing analog signals in mixed-signal SOC. We claim that the approach that is going to be presented is able to achieve wide frequency range, and covers a large range of applications with constant performance, allied to digital configuration compatibility. Our primary assumptions are to use a fixed analog block and to promote application configurability in the digital domain, which leads to a mixed-signal interface. The use of a fixed analog block avoids the performance loss common to configurable analog blocks. The usage of configurability on the digital domain makes possible the use of all existing tools for high level design, simulation and synthesis to implement the target application, with very good performance prediction. The proposed approach utilizes the concept of frequency translation (mixing) of the input signal followed by its conversion to the ΣΔ domain, which makes possible the use of a fairly constant analog block, and also, a uniform treatment of input signal from DC to high frequencies. The programmability is performed in the ΣΔ digital domain where performance can be closely achieved according to application specification. The interface performance theoretical and simulation model are developed for design space exploration and for physical design support. Two prototypes are built and characterized to validate the proposed model and to implement some application examples. The usage of this interface as a multi-band parametric ADC and as a two channels analog multiplier and adder are shown. The multi-channel analog interface architecture is also presented. The characterization measurements support the main advantages of the approach proposed.

Predicting Amazon Deforestation through the deterninants of demand for agricultural land

This paper develops a model of deforestation pressure in the Amazon. It is based on the determinants of demand for agricultural land, i.e. the interactions between population dynamics, urbanization and the growth of local markets, land prices, and government spending and policies. The mo deI is estimated using data from the period 1970 - 1985, and predictions for the period 1985 - 2010 are made under explicit assumptions about the underlying factors of deforestation. The predictions indicate that economic growth in the Amazon is likely to continue at high rates even if the federal government abandons its aggressive development policy. Deforestation will be much smaller if they do, though, since the active development policies tend to promote wasteful use of land.

Análise econômica da reforma fiscal do PIS e da COFINS: integrando um modelo de micro-simulação com um modelo de equilíbrio geral computável

Neste texto é apresentado o relatório final do projeto 561/06, “Análise Econômica da Reforma Fiscal do PIS-COFINS: Integrando um modelo de micro-simulação com um Modelo de Equilíbrio Geral Computável”. Essencialmente trata-se de uma extensão metodológica do projeto 461/04, visando um aprimoramento da quantificação dos impactos sobre indicadores de bem estar, particularmente pobreza e desigualdade. Além do modelo de Equilíbrio Geral, busca-se uma integração com um modelo de micro-simulação, baseado nas pesquisas domiciliares com o intuito de aprofundar e identificar o impacto que a reforma fiscal teve sobre indivíduos e famílias brasileiras, fazendo com estes sejam identificados com uma precisão muito maior, na medida em que a pesquisa anterior permitia apenas a identificação de um agrupamento representativo da população brasileira, enquanto esta permite a integração no modelo das amostras individuais presentes na PNAD. Os resultados apresentados são sensíveis a nova metodologia utilizada.

Contagion in financial networks: a network theory and agent-based approaches to modeling the spread of risk in financial systems

Esta dissertação estuda a propagação de crises sobre o sistema financeiro. Mais especi- ficamente, busca-se desenvolver modelos que permitam simular como um determinado choque econômico atinge determinados agentes do sistema financeiro e apartir dele se propagam, transformando-se em um problema sistêmico. A dissertação é dividida em dois capítulos,além da introdução. O primeiro capítulo desenvolve um modelo de propa- gação de crises em fundos de investimento baseado em ciência das redes.Combinando dois modelos de propagação em redes financeiras, um simulando a propagação de perdas em redes bipartites de ativos e agentes financeiros e o outro simulando a propagação de perdas em uma rede de investimentos diretos em quotas de outros agentes, desenvolve-se um algoritmo para simular a propagação de perdas através de ambos os mecanismos e utiliza-se este algoritmo para simular uma crise no mercado brasileiro de fundos de investimento. No capítulo 2,desenvolve-se um modelo de simulação baseado em agentes, com agentes financeiros, para simular propagação de um choque que afeta o mercado de operações compromissadas.Criamos também um mercado artificial composto por bancos, hedge funds e fundos de curto prazo e simulamos a propagação de um choque de liquidez sobre um ativo de risco securitizando utilizado para colateralizar operações compromissadas dos bancos.

Estudo do processo de combustão in-situ em reservatórios maduros de óleos médios e leves (high pressure air injection)

Nearly 3 x 1011 m3 of medium and light oils will remain in reservoirs worldwide after conventional recovery methods have been exhausted and much of this volume would be recovered by Enhanced Oil Recovery (EOR) methods. The in-situ combustion (ISC) is an EOR method in which an oxygen-containing gas is injected into a reservoir where it reacts with the crude oil to create a high-temperature combustion front that is propagated through the reservoir. The High Pressure Air Injection (HPAI) method is a particular denomination of the air injection process applied in light oil reservoirs, for which the combustion reactions are dominant between 150 and 300°C and the generation of flue gas is the main factor to the oil displacement. A simulation model of a homogeneous reservoir was built to study, which was initially undergone to primary production, for 3 years, next by a waterflooding process for 21 more years. At this point, with the mature condition established into the reservoir, three variations of this model were selected, according to the recovery factors (RF) reached, for study the in-situ combustion (HPAI) technique. Next to this, a sensitivity analysis on the RF of characteristic operational parameters of the method was carried out: air injection rate per well, oxygen concentration into the injected gas, patterns of air injection and wells perforations configuration. This analysis, for 10 more years of production time, was performed with assistance of the central composite design. The reservoir behavior and the impacts of chemical reactions parameters and of reservoir particularities on the RF were also evaluated. An economic analysis and a study to maximize the RF of the process were also carried out. The simulation runs were performed in the simulator of thermal processes in reservoirs STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modelling Group). The results showed the incremental RF were small and the net present value (NPV) is affected by high initial investments to compress the air. It was noticed that the adoption of high oxygen concentration into the injected gas and of the five spot pattern tends to improve the RF, and the wells perforations configuration has more influence with the increase of the oil thickness. Simulated cases relating to the reservoir particularities showed that smaller residual oil saturations to gas lead to greater RF and the presence of heterogeneities results in important variations on the RF and on the production curves

Análise de viabilidade de injeção de fluidos alternativos ao vapor em reservatórios de óleo pesado

Many of hydrocarbon reserves existing in the world are formed by heavy oils (°API between 10 and 20). Moreover, several heavy oil fields are mature and, thus, offer great challenges for oil industry. Among the thermal methods used to recover these resources, steamflooding has been the main economically viable alternative. Latent heat carried by steam heats the reservoir, reducing oil viscosity and facilitating the production. This method has many variations and has been studied both theoretically and experimentally (in pilot projects and in full field applications). In order to increase oil recovery and reduce steam injection costs, the injection of alternative fluid has been used on three main ways: alternately, co-injected with steam and after steam injection interruption. The main objective of these injection systems is to reduce the amount of heat supplied to the reservoir, using cheaper fluids and maintaining the same oil production levels. This works discusses the use of carbon dioxide, nitrogen, methane and water as an alternative fluid to the steam. The analyzed parameters were oil recoveries and net cumulative oil productions. The reservoir simulation model corresponds to an oil reservoir of 100 m x 100 m x 28 m size, on a Cartesian coordinates system (x, y and z directions). It is a semi synthetic model with some reservoir data similar to those found in Brazilian Potiguar Basin. All studied cases were done using the simulator STARS from CMG (Computer Modelling Group, version 2009.10). It was found that waterflood after steam injection interruption achieved the highest net cumulative oil compared to other fluids injection. Moreover, it was observed that steam and alternative fluids, co-injected and alternately, did not present increase on profitability project compared with steamflooding

Modelo em dinâmica de sistemas para gestão de aeroportos brasileiros

The importance of the airport sector in the development of a country refers to the need for studies on management of airports, to aid the process of decision making. In Brazil, growth in passenger demand is why investments in order to balance the capacity of an airport with air demand. Thus, the study aims to develop a model for Dynamic Systems able to assist airport management in Brazilian sizing subsystems an airport (Passenger Terminal, Runway and Patio). The methodology of this work consists in the steps of defining the problem, formulating the hypothesis dynamic building simulation model, and validation experiments. Finally, we examined the status of each subsystem in thirteen Brazilian airports in scenarios current, most likely and optimistic for air passenger demand

PCJ River Basins' Water Availability Caused by Water Diversion Scenarios to Supply Metropolitan Areas of So Paulo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A gestão da qualidade nos cursos de graduação a distância da UFRN/SEDIS : a percepção dos discentes

The management of water resources in the river basin level, as it defines the Law nº 9433/97, requires the effective knowledge of the processes of hydrological basin, resulting from studies based on consistent series of hydrological data that reflect the characteristics of the basin. In this context, the objective of this work was to develop the modeling of catchment basin of the river Jundiaí - RN and carry out the study of attenuation of a flood of the dam Tabatinga, by means of a monitoring project of hydrological data and climatology of the basin, with a view to promoting the development of research activities by applying methodologies unified and appropriate for the assessment of hydrological studies in the transition region of the semiarid and the forest zone on the coast of Rio Grande do Norte. For the study of the hydrological characteristics of the basin was conducted the automatic design of the basin of the river Jundiaí, with the aid of programs of geoprocessing, was adopted a hydrological model daily, the NRCS, which is a model determined and concentrated. For the use of this model was necessary to determine some parameters that are used in this model, as the Curve Number. Having in mind that this is the first study that is being conducted in the basin with the employment of this model, it was made sensitivity analysis of the results of this model from the adoption of different values of CN, situated within a range appropriate to the conditions of use, occupation and the nature of the soil of this basin. As the objective of this study was also developing a simulation model of the operation of the Tabatinga dam and with this flood control caused in the city of Macaíba, it was developed a mathematical model of fluid balance, developed to be used in Microsoft Excel. The simulation was conducted in two phases: the first step was promoted the water balance daily that allowed the analysis of the sensitivity of the model in relation to the volume of waiting, as well as the determination of the period of greatest discharges daily averages. From this point, it was assumed for the second stage, which was in the determination of the hydrograph of discharges effluent slots, that was determined by means of the fluid balance time, on the basis of the discharges effluents generated by a mathematical equation whose parameters were adjusted according to the hydrograph daily. Through the analyzes it was realized that the dam Tabatinga only has how to carry out the attenuation of floods through the regularization of the volume of waiting, with this there is a loss of approximately 56.5% on storage capacity of this dam, because for causing the attenuation effect of filled the shell of this dam has to remain more than 5m below the level of the sill, representing at least 50.582.927m3. The results obtained with the modeling represents a first step in the direction of improving the level of hydrological information about the behavior of the basins of the semiarid. In order to monitor quantitatively the hydrographic basin of the river Jundiaí will be necessary to install a rain gauge register, next to the Tabatinga dam and a pressure transducer, for regular measurements of flow in the reservoir of the dam. The climatological data will be collected in full automatic weather station installed in Agricultural School Jundiaí