Assessment of the ozone sensitivity of 22 native plant species from mediterranean annual pastures based on visible injury

Ozone (O3) phytototoxicity has been reported on a wide range of plantspecies, inducing the appearance of specific foliar injury or increasing leaf senescence. No information regarding the sensitivity of plantspecies from dehesa Mediterranean grasslands has been provided in spite of their great biological diversity. A screening study was carried out in open-top chambers (OTCs) to assess the O3-sensitivity of 22 representative therophytes of these ecosystems based on the appearance and extent of foliar injury. A distinction was made between specific O3injury and non-specific discolorations. Three O3 treatments (charcoal-filtered air, non-filtered air and non-filtered air supplemented with 40 nl l−1 O3 during 5 days per week) and three OTCs per treatment were used. The Papilionaceae species were more sensitive to O3 than the Poaceae species involved in the experiment since ambient levels induced foliar symptoms in 67% and 27%, respectively, of both plant families. An O3-sensitivity ranking of the species involved in the assessment is provided, which could be useful for bioindication programmes in Mediterranean areas. The assessed Trifoliumspecies were particularly sensitive since foliar symptoms were apparent in association with O3 accumulated exposures well below the current critical level for the prevention of this kind of effect. The exposure indices involving lower cut-off values (i.e. 30 nl l−1) were best related with the extent of O3-induced injury on these species.

Refining predictions of iberian plant distribution: lessons from p. nigra and p. sylvestris palaeoecological-based habitat suitability models

In recent years, challenged by the climate scenarios put forward by the IPCC and its potential impact on plant distribution, numerous predictive techniques -including the so called habitat suitability models (HSM)- have been developed. Yet, as the output of the different methods produces different distribution areas, developing validation tools are strong needs to reduce uncertainties. Focused in the Iberian Peninsula, we propose a palaeo-based method to increase the robustness of the HSM, by developing an ecological approach to understand the mismatches between the palaeoecological information and the projections of the HSMs. Here, we present the result of (1) investigating causal relationships between environmental variables and presence of Pinus sylvestris L. and P. nigra Arn. available from the 3rd Spanish Forest Inventory, (2) developing present and past presence-predictions through the MaxEnt model for 6 and 21 kyr BP, and (3) assessing these models through comparisons with biomized palaeoecological data available from the European Pollen Database for the Iberian Peninsula.

Responses of riparian guilds to flowalterations in a Mediterranean stream

Questions: Do Mediterranean riparian guilds show distinct responses to stream water declines? If observed,which are the most sensitive and resilient guilds and theirmost affected attributes? Location: Tie¿tar river below the Rosarito dam, central-western Spain. Methods: We identified riparian guilds based on key woody species features and species distribution within this Mediterranean river corridor, and evaluated similarity of their responses to long-term flow alteration (i.e. stream water declines since dam construction in 1959). Hierarchical cluster analysis was used to group surveyed vegetation bands according to species composition. The groups were designated as riparian guilds where each vegetation group comprising a guild: (1) contains species sharing similar features (using PCA); and (2) shares a similar environment (using DCA). Changes in several guild attributes (i.e. dominance and species composition, diversity and establishment patterns) during the regulated period were compared statistically. We used pre- and post-dam established vegetation bands identified based on old (1956) and modern (2006) aerial photographs and field measurements of woody species diameter. Results: Responses to flow alterations varied between guilds according to ecological requirements of their species. The ability to survive water stress (i.e. ?Xeric? guilds) and drag forces caused by floods (?Torrential? guilds) allowed certain pioneer shrub-dominated guilds (e.g. Flueggea tinctoria and Salix salviifolia) to spread on newly emerged surfaces downward to the main channel after flow alterations, although new shrubland had less species diversity than pre-dam shrubland. In contrast, new hydromorphological conditions following damming limited recruitment of native late-successional tree guilds sensitive to floods (to drag forces, inundation and anoxia; i.e. ?Slow-water? and ?Flood-sensitive?, respectively) and those with greater water requirements (i.e. ?Hydric?) (e.g. Alnus glutinosa and Celtis australis), although species diversity increased in this mature forest through co-existence of remaining riparian species and new arrival of upland species. Conclusions: Changes in several riparian attributes after flow alterations differed between guilds. Stream water declines after damming caused shifts in species-poor pioneer shrubland downwards to the watered channel, resulting in severe declines ofmaturenative forest.Understanding vegetation guild responses provides information about general trends in plant populations and assemblage structures expected to occur during river development and flow regulation, increasing our capacity to detect and synthesize complex flowalteration?riparian ecosystem response relationships, and anticipate irreversible impacts.

On the spatial distribution of woody plant species in a tropical montane cloud forest

Abstract The cloud forest is a special type of forest ecosystem that depends on suitable conditions of humidity and temperature to exist; hence, it is a very fragile ecosystem. The cloud forest is also one of the richest ecosystems in terms of species diversity and rate of endemism. However, today, it is one of the most threatened ecosystems in the world. Little is known about tree species distribution and coexistence among cloud forest trees. Trees are essential to understanding ecosystem functioning and maintenance because they support the ecosystem in important ways. For this dissertation, an analysis of woody plant species distribution at a small scale in a north-Peruvian Andean cloud forest was performed, and some of the factors implicated in the observed patterns were identified. Towards that end, different natural factors acting on species distribution within the forest were investigated: (i) intra-specific arrangements, (ii) heterospecific spatial relationships and (iii) relationships with external environmental factors. These analyses were conducted first on standing woody plants and then on seedlings. The woody plants were found to be clumped in the forest, either considering all the species together or each species separately. However, each species presented a specific pattern and specific spatial relationship among different-age individuals. Dispersal mode, growth form and shade tolerance played roles in the final distribution of the species. Furthermore, spatial associations among species, either positive or negative, were observed. These associations were more numerous when considering individuals of the interacting species at different developmental stages, i.e., younger individuals from one species and older individuals from another. Accordingly, competition and facilitation are asymmetric processes and vary throughout the life of an individual. Moreover, some species appear to prefer certain habitat conditions and avoid other habitats. The habitat definition that best explains species distribution is that which includes both environmental and stand characteristics; thus, a combination of these factors is necessary to understanding species' niche preferences. Seedling distribution was also associated with habitat conditions, but these conditions explained less than the 30% of the spatial variation. The position of conspecific adult individuals also affected seedling distribution; although the seedlings of many tree species avoid the vicinity of conspecifics, a few species appeared to prefer the formation of cohorts around their parent trees. The importance of habitat conditions and distance dependence with conspecifics varied among regions within the forest as well as on the developmental stage of the stand. The results from this thesis suggest that different species can coexist within a given space, forming a “puzzle” of species as a result of the intra- and interspecific spatial relationships along with niche preferences and adaptations that operate at different scales. These factors not only affect each species in a different way, but specific preferences also vary throughout species' lifespans. Resumen Resumen El bosque de niebla es uno de los ecosistemas más amenazados del mundo además de ser uno de los más frágiles. Son formaciones azonales que dependen de la existencia de unas condiciones de humedad y temperatura que permitan la formación de nubes que cubran el bosque; lo que dificulta en gran medida su conservación. También es uno de los ecosistemas con mayor riqueza de especies además de tener uno de los mayores porcentajes de endemismos. Uno de los aspectos más importantes para entender el ecosistema, es identificar y entender los elementos que lo componen y los mecanismos que regulan las relaciones entre ellos. Los árboles son el soporte del ecosistema. Sin embargo, apenas hay información sobre la distribución y coexistencia de los árboles en los bosques de niebla. Esta tesis presenta un análisis de la distribución a pequeña escala de las plantas leñosas en un bosque de niebla situado en la cordillera andina del norte de Perú; así como el análisis de algunos de los factores que pueden estar implicados en que se origine la distribución observada. Para este propósito se estudia cómo influyen factores de diferente naturaleza en la distribución de las especies (i) organización intra-específica (ii) relaciones espaciales heterospecíficas y (iii) relación con factores ambientales externos. En estos análisis se estudiaron primero las plantas jóvenes y las adultas, y después las plántulas. Los árboles aparecieron agregados en el bosque, tanto considerando todos a la vez como cuando se estudió cada especie por separado. Sin embargo, cada especie mostró un patrón distinto así como una particular relación espacial entre individuos jóvenes y adultos. El modo de dispersión, la forma de vida y la tolerancia de la especies estuvieron relacionados con el patrón general observado. Se vio también que ciertas especies aparecían relacionadas con otras, tanto de forma positiva (compartiendo zonas) como negativa (apareciendo en áreas distintas). Las asociaciones fueron mucho más numerosas cuando se consideraron los pares de especies en diferente estado de desarrollo, es decir, individuos jóvenes de una especie e individuos mayores de la otra. Eso indicaría que los procesos de competencia y facilitación son asimétricos y además varían durante la vida de la planta. Por otro lado, algunas especies aparecen preferentemente bajo ciertas condiciones de hábitat y evitan otras. La definición de hábitat a la que mejor responden las especies es cuando se incluyen tanto variables ambientales como de masa; así que ambos tipos de variables son necesarias para entender la preferencia de las especies por ciertos nichos. La distribución de las plántulas también estuvo relacionada con condiciones de hábitat, pero eso sólo llegaba a explicar hasta un 30% de la variabilidad espacial. La posición de los adultos de la misma especie también afectó a la distribución de las plántulas. En bastantes especies las plántulas evitan la cercanía de adultos de su misma especie, padres potenciales, aunque algunas especies aisladas mostraron el patrón contrario y aparecieron preferentemente en las mismas áreas que sus padres. La importancia de las condiciones de hábitat y posición de los adultos en la disposición de las plántulas varía de una zona a otra del bosque y además también varía según el estado de desarrollo de la masa.

Estimation of the solubility parameters of model plant surfaces and agrochemicals: a valuable tool for understanding plant surface interactions

Background Most aerial plant parts are covered with a hydrophobic lipid-rich cuticle, which is the interface between the plant organs and the surrounding environment. Plant surfaces may have a high degree of hydrophobicity because of the combined effects of surface chemistry and roughness. The physical and chemical complexity of the plant cuticle limits the development of models that explain its internal structure and interactions with surface-applied agrochemicals. In this article we introduce a thermodynamic method for estimating the solubilities of model plant surface constituents and relating them to the effects of agrochemicals. Results Following the van Krevelen and Hoftyzer method, we calculated the solubility parameters of three model plant species and eight compounds that differ in hydrophobicity and polarity. In addition, intact tissues were examined by scanning electron microscopy and the surface free energy, polarity, solubility parameter and work of adhesion of each were calculated from contact angle measurements of three liquids with different polarities. By comparing the affinities between plant surface constituents and agrochemicals derived from (a) theoretical calculations and (b) contact angle measurements we were able to distinguish the physical effect of surface roughness from the effect of the chemical nature of the epicuticular waxes. A solubility parameter model for plant surfaces is proposed on the basis of an increasing gradient from the cuticular surface towards the underlying cell wall. Conclusions The procedure enabled us to predict the interactions among agrochemicals, plant surfaces, and cuticular and cell wall components, and promises to be a useful tool for improving our understanding of biological surface interactions.

Estimation of the solubility parameters of model plant surfaces and agrochemicals: a valuable tool for understanding plant surface interactions

Background Most aerial plant parts are covered with a hydrophobic lipid-rich cuticle, which is the interface between the plant organs and the surrounding environment. Plant surfaces may have a high degree of hydrophobicity because of the combined effects of surface chemistry and roughness. The physical and chemical complexity of the plant cuticle limits the development of models that explain its internal structure and interactions with surface-applied agrochemicals. In this article we introduce a thermodynamic method for estimating the solubilities of model plant surface constituents and relating them to the effects of agrochemicals. Results Following the van Krevelen and Hoftyzer method, we calculated the solubility parameters of three model plant species and eight compounds that differ in hydrophobicity and polarity. In addition, intact tissues were examined by scanning electron microscopy and the surface free energy, polarity, solubility parameter and work of adhesion of each were calculated from contact angle measurements of three liquids with different polarities. By comparing the affinities between plant surface constituents and agrochemicals derived from (a) theoretical calculations and (b) contact angle measurements we were able to distinguish the physical effect of surface roughness from the effect of the chemical nature of the epicuticular waxes. A solubility parameter model for plant surfaces is proposed on the basis of an increasing gradient from the cuticular surface towards the underlying cell wall. Conclusions The procedure enabled us to predict the interactions among agrochemicals, plant surfaces, and cuticular and cell wall components, and promises to be a useful tool for improving our understanding of biological surface interactions.

Ground cover and leaf area index relationship in a grass, legume and crucifer crop

Canopy characterization is essential for describing the interaction of a crop with its environment. The goal of this work was to determine the relationship between leaf area index (LAI) and ground cover (GC) in a grass, a legume and a crucifer crop, and to assess the feasibility of using these relationships as well as LAI-2000 readings to estimate LAI. Twelve plots were sown with either barley (Hordeum vulgare L.), vetch (Vicia sativa L.), or rape (Brassica napus L.). On 10 sampling dates the LAI (both direct and LAI-2000 estimations), fraction intercepted of photosynthetically active radiation (FIPAR) and GC were measured. Linear and quadratic models fitted to the relationship between the GC and LAI for all of the crops, but they reached a plateau in the grass when the LAI mayor que 4. Before reaching full cover, the slope of the linear relationship between both variables was within the range of 0.025 to 0.030. The LAI-2000 readings were linearly correlated with the LAI but they tended to overestimation. Corrections based on the clumping effect reduced the root mean square error of the estimated LAI from the LAI-2000 readings from 1.2 to less than 0.50 for the crucifer and the legume, but were not effective for barley.

Assessing agriculture-water relationships: a Pan-European multidimensional modelling approach.

This paper aims at developing a simulation framework to jointly assess agricultural and water issues. While the strong linkages between water, food, and the environment call for an integrated and multidisciplinary modelling approach, a complete and consistent modelling system to evaluate food-water relationships in Europe was missing so far. The spatial economic simulation model for agriculture CAPRI, which comprises a set of environmental indicators to assess food-environment interrelations within European regions, has been extended to account for food-water links. This modelling framework enables simulating the potential impact of climate change and water availability on agricultural production at the EU regional level, as well as looking at the sustainable use of water, the implementation of water policies or the integration of water issues in the Common Agricultural Policy

Real time power plant simulation platform for training on Electrical Protections and Automatic Voltage Regulators

Electrical Protection systems and Automatic Voltage Regulators (AVR) are essential components of actual power plants. Its installation and setting is performed during the commissioning, and it needs extensive experience since any failure in this process or in the setting, may entails some risk not only for the generator of the power plant, but also for the reliability of the power grid. In this paper, a real time power plant simulation platform is presented as a tool for improving the training and learning process on electrical protections and automatic voltage regulators. The activities of the commissioning procedure which can be practiced are described, and the applicability of this tool for improving the comprehension of this important part of the power plants is discussed. A commercial AVR and a multifunction protective relay have been tested with satisfactory results.

Validation Study of the Use of Matlab/Simulink Synchronous-Machine Block for Accurate Power-Plant Stability Studies

This paper presents results of the validity study of the use of MATLAB/Simulink synchronous-machine block for power-system stability studies. Firstly, the waveforms of the theoretical synchronous-generator short-circuit currents are described. Thereafter, the comparison between the currents obtained through the simulation model in the sudden short-circuit test, are compared to the theoretical ones. Finally, the factory tests of two commercial generating units are compared to the response of the synchronous generator simulation block during sudden short-circuit, set with the same real data, with satisfactory results. This results show the validity of the use of this generator block for power plant simulation.

Modeling GHG emissions, N and C dynamics in Spanish agricultural soils.

To date, only few initiatives have been carried out in Spain in order to use mathematical models (e.g. DNDC, DayCent, FASSET y SIMSNIC) to estimate nitrogen (N) and carbon (C) dynamics as well as greenhouse gases (GHG) in Spanish agrosystems. Modeling at this level may allow to gain insight on both the complex relationships between biological and physicochemical processes, controlling the processes leading to GHG production and consumption in soils (e.g. nitrification, denitrification, decomposing, etc.), and the interactions between C and N cycles within the different components of the continuum plant-soil-environment. Additionally, these models can simulate the processes behind production, consumition and transport of GHG (e.g. nitrous oxide, N2O, and carbon dioxide, CO2) in the short and medium term and at different scales. Other sources of potential pollution from soils can be identified and quantified using these process-based models (e.g. NO3 y NH3).

Contribution to Load-Frequency Regulation of a Hydropower Plant with Long Tail-Race Tunnel

In this paper, a hydroelectric power plant with long tail-race tunnel has been modelled for assessing its contribution to secondary regulation reserve. Cavitation problems, caused by the discharge conduit length, are expected downstream the turbine where low pressure appears during regulation manoeuvres. Therefore, governor's gains should be selected taking into account these phenomena. On the other hand, regulation services bidden by the plant operator should fulfil TSO (Transmission System Operator) quality requirements. A methodology for tuning governor PI gains is proposed and applied to a Hydro power plant in pre-design phase in northwest area of Spain. The PI gains adjustment proposed provides a proper plant response, according to some established indexes, while avoiding cavitation phenomena.

3D Maize Plant Reconstruction Based on Georeferenced Overlapping LiDAR Point Clouds

3D crop reconstruction with a high temporal resolution and by the use of non-destructive measuring technologies can support the automation of plant phenotyping processes. Thereby, the availability of such 3D data can give valuable information about the plant development and the interaction of the plant genotype with the environment. This article presents a new methodology for georeferenced 3D reconstruction of maize plant structure. For this purpose a total station, an IMU, and several 2D LiDARs with different orientations were mounted on an autonomous vehicle. By the multistep methodology presented, based on the application of the ICP algorithm for point cloud fusion, it was possible to perform the georeferenced point clouds overlapping. The overlapping point cloud algorithm showed that the aerial points (corresponding mainly to plant parts) were reduced to 1.5%–9% of the total registered data. The remaining were redundant or ground points. Through the inclusion of different LiDAR point of views of the scene, a more realistic representation of the surrounding is obtained by the incorporation of new useful information but also of noise. The use of georeferenced 3D maize plant reconstruction at different growth stages, combined with the total station accuracy could be highly useful when performing precision agriculture at the crop plant level.

Factores anatómicos, dendrométricos y climáticos implicados en la producción de resina de Pinus pinaster AIT. : aplicación a la mejora de los métodos de resinación

Pinus pinaster Ait. es la conífera con mayor área de distribución en la Península Ibérica y es, a día de hoy, la única especie resinada en nuestro país. La inducción del flujo de resina al exterior para su recolección a través de distintos tipos de heridas ha sido practicada desde hace miles de años por distintas culturas. En todos los casos, las técnicas desarrolladas se basan en la estimulación del característico sistema de defensa de las pináceas. En los últimos siete años se viene observando una tendencia de incremento sustancial de la superficie resinada en España, acompañada por avances tecnológicos dirigidos a la mecanización y mejora de estimulantes. El aprovechamiento resinero se perfila como un sector estratégico en la generación de empleo rural y la conservación de ecosistemas. La industria resinera demanda métodos de extracción más eficaces, una selvicultura adecuada y actualizada, y condiciones laborales de los resineros más dignas con objeto de llegar a ser competitiva en el mercado internacional. Este trabajo se centra en ampliar el conocimiento sobre el sistema de defensa de P. pinaster, concretamente sobre las estructuras y procesos que pueden afectar a la producción de resina. Se analizan las relaciones entre las características anatómicas del xilema, destacando las relacionadas con los canales resiníferos, las variables dendrométricas y dasométricas de la masa y el flujo de resina (objetivo 1). Se estudia cómo estas relaciones son moduladas por las heridas de resinación dependiendo de la técnica de resinación aplicada (objetivo 2), el clima y el balance hídrico del suelo (objetivo 3). El material vegetal, las muestras de suelo y los datos de producción de resina y climáticos usados en esta tesis han sido recogidos en tres montes de utilidad pública; MUP 101 en Armuña, MUP 108 en Melque de Cercos y MUP 117 en Nieva (en esta última solo se recogieron los datos de producciones), todos ellos pinares monoespecíficos de P. pinaster localizados en la denominada Tierra de Pinares Segoviana. En los árboles de nuestro estudio se han aplicado cuatro métodos de resinación: método de pica de corteza con estimulante y método mecanizado con estimulante, ambos en sentido ascendente y descendente. En los trabajos realizados para el análisis de la influencia de la anatomía constitutiva en la producción de resina (objetivo 1) y el efecto del clima (objetivo 3), se obtuvieron muestras del xilema de 26 árboles resinados en Melque de Cercos y Armuña y 12 árboles control sin resinar. Para caracterizar los pies estudiados, se midió la altura, diámetro normal y porcentaje de copa viva. Las muestras de tejido fueron recogidas en una zona del tronco a una distancia del límite de la herida considerada en la bibliografía como no afectada (anatomía constitutiva). Para el análisis de las alteraciones anatómicas inducidas por la herida (objetivo 2), se recogieron muestras en ocho de los individuos en los que se habían realizado los distintos métodos de resinación descritos y en cinco árboles control. Se obtuvieron ocho muestras de tejido distribuidas en la parte superior, inferior, lateral y centro de la herida de cada uno de los árboles resinados. Para establecer las diferencias en la producción de resina según el método de resinación, se analizaron las producciones de 561 árboles resinados en 2012 con estos cuatro métodos en Nieva. Los principales resultados de estos trabajos muestran que la producción de resina está ligada al volumen de canales (axiales y radiales) y a la frecuencia de canales radiales existentes en el árbol antes de efectuar ninguna herida (sistema constitutivo). De esta manera, los árboles grandes productores de resina mostraron una red de canales más densa que aquellos con producciones medias. Una vez realizada la herida de resinación, observamos una disminución del ancho del anillo de crecimiento y del tamaño medio de los canales axiales a la vez que se incrementaba la frecuencia y área ocupada por mm2 de anillo de estos canales. Estos cambios perduraron en el árbol durante al menos tres años y fueron distintos dependiendo de la localización en el entorno de la herida y del método de resinación. Las respuestas más intensas a la herida se observaron el año siguiente a la realización de la misma, en dirección axial, para las distancias más próximas al límite de la herida y para los métodos de resinación en sentido ascendente. Además, se ha constatado que como consecuencia de las heridas de resinación se produjeron cambios en la anatomía del xilema en zonas alejadas de la herida, tanto en el año de la herida como años posteriores. Es decir, se observó una respuesta sistémica del árbol. Respecto al papel del clima como regulador de la respuesta del árbol, se ha evidenciado que la temperatura, la radiación y la ETP influyeron en la producción de resina, no solo durante la campaña de resinación, sino también durante los meses anteriores. El déficit hídrico favoreció la producción y la formación de canales axiales pero, a partir de un determinado umbral, esa relación se invirtió y las lluvias estivales incrementaron la producción. Algunas de estas variables climáticas se asociaron a cambios en el tamaño y frecuencia de las estructuras secretoras, las cuales posiblemente modulan la respuesta defensiva de la planta. La dendrometría del árbol (evaluada a través del diámetro normal, altura y porcentaje de copa viva), la densidad de la masa y el tipo de suelo influyeron en el potencial de producción de resina de P. pinaster. Árboles más vigorosos, parcelas con menores densidades y suelos con más capacidad para la retención de agua y nutrientes presentaron producciones mayores. Estos trabajos se complementan en anexos con una caracterización del sistema socio-ecológico del pinar en resinación. En ese trabajo se identifican sus potenciales servicios ecosistémicos y se evalúa su grado de vinculación con el aprovechamiento resinero con objeto de valorar su funcionalidad y aproximar una valoración económica de modo que sea posible apreciar la importancia económica de los mismos. Para concluir, podemos resaltar que son necesarios más trabajos de carácter científico para avanzar en la comprensión de los procesos anatómicos y fisiológicos que regulan la secreción de resina en P. pinaster y sus interacciones con el medio. Esto permitiría avances certeros hacia el desarrollo de métodos de extracción más eficaces, una selvicultura óptima, el reconocimiento de los beneficios socio-ecológicos y económicos del aprovechamiento y, de manera general, una bibliografía amplia y fiable para la consulta y desarrollo de futuras mejoras que posibiliten la reactivación y conservación de la resinación como aprovechamiento rentable. ABSTRACT Pinus pinaster Ait. is the most widespread conifer in Spain and is now the only species tapped for its oleoresin. External induction of resin secretion, based on the defense system of Pinus trees, has been performed by humans since Classical times through various methods. The socio-economic implication of this practice in Spain justifies a new approach to improve tapping methodology and understand the effects of this activity on the tree. In the last five years, sharp increases in the price of natural resins, accompanied by technological advances directed toward mechanization, have made resin tapping a strategic activity for rural development and forest conservation. The resin industry demands more efficient tapping methods and forest management plans as a way to increase competitiveness in a global market. In this way, this work focuses on the study of the defense system of P. pinaster, with the aim to understand the effects of anatomical and physiological characteristics and environmental conditions on resin yield. The relationships between anatomical variables -with special focus on resin canals-, dendrometric and dasometric variables, and resin yield will be evaluated (objective 1). The tapping wound effects (objective 2) and the intra- and inter-annual variability of climate conditions and soil water availability influence (objective 3) on resin yield will be also studied. The plant and soil material and the resin yield and climatic data used in this thesis have been collected in stands of three public forests of P. pinaster; Armuña, Melque de Cercos and Nieva, located in Segovia (Central Spain). Trees were tapped using two different methods: mechanized or traditional tool, in both upwards and downwards direction. Twenty-six tapped trees of contrasting resin yield classes and twelve non-tapped (control) trees, growing in two locations (Armuña y Melque de Cercos) with the same climate but different stand density and soil characteristics, were selected for studying the role of tree size, xylem anatomy at distal parts aside from the tapping wound (objective 1) and climate influence (objective 3) on resin yield. Concerning the tree defenses induced by the tapping wound (objective 2), the xylem of eight trees, tapped with the two described methods in both upwards and downwards direction, were analyzed. From each tapped tree, eight cores were collected at different locations and varying distances from the tapping wound. In each core, a histological analysis was made. Growth ring width, earlywood and latewood width, and axial canal frequency, area, mean size and location were measured. The effect of the tapping method on resin yield was assessed in 561 P. pinaster tapped trees in a stand in Nieva. In tissues not affected by the tapping wound, the frequency of radial resin canals and the total volume of resin canals were related to resin yield. The frequency of radial canals and the resin yield were strongly related to tree diameter and percentage of live crown. High area of axial resin canals per mm2 was related to high yielding trees, but only in the location with higher plant density and poorer soil quality. In tapped trees, an increase in axial canal frequency and area was found during the three years following the start of tapping activity, suggesting that canal formation is a systemic induced response to wounding. The highest mean annual resin yield was found using the traditional tool in upwards direction, which also induced the highest increase in axial canal frequency and area. The lowest yield was found for mechanized tapping, which showed no differences between the upwards and downwards directions. The strongest induction of systemic induced responses in terms of resin canal frequency and area was detected one year after tapping for upwards tapping. This suggests the involvement of signaling processes that spread mainly upwards, and the importance of adaptive processes as a defense against periodic insect attacks. Intra-annual variation in resin yield was strongly correlated with temperature, solar radiation, potential evapotranspiration and soil water deficit. Inter-annual variation in resin yield and resin canal abundance were correlated with temperature and water deficit in spring, but above a certain threshold of cumulated water deficit in summer rainfall favored resin yield. Under adverse climate scenarios where resource optimization is desirable, a reduced tapping season during the warmest months (June–September) would be advisable, assuming a very small production loss relative to traditional tapping season. Similarly, in years with a rainy summer and/or dry spring, a slightly longer tapping season could be suggested, as resin yield increases after these events. Tree diameter and percentage of live crown, and radial resin canal frequency could be useful criteria for estimating resin yields in P. pinaster. Vigorous trees in lower density stands and growing up in good quality soils will be the most productive. These conclusions could be applied to improve tapping management and breeding programs. These works are complemented with socio-ecological characterization, the identification of the main ecosystem services and an assessment of the possible economic impact derived from the tapping practice. To conclude, more scientific studies are necessary for understanding the anatomical and physiological processes behind resin synthesis and their interactions with the environment. This would afford further progresses towards an extensive and reliable bibliography and improved tapping methods and optimal selvicultural guide lines.

The interspecific mass–density relationship and plant geometry

We present an a priori theoretical framework for the interspecific allometric relationship between stand mass and plant population density. Our model predicts a slope of −\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \setlength{\oddsidemargin}{-69pt} \begin{document} \begin{equation*}\frac{1}{3}\end{equation*}\end{document} between the logarithm of stand mass and the logarithm of stand density, thus conflicting with a previously assumed slope of −½. Our model rests on a heuristic separation of resource-limited living mass and structural mass in the plant body. We point out that because of similar resource requirements among plants of different sizes, a nonzero plant mass–density slope is primarily defined by structural mass. Specifically, the slope is a result of (i) the physical size-dependent relationship between stem width and height, (ii) foliage-dependent demands of conductance, and (iii) the cumulative nature of structural mass. The data support our model, both when the potential sampling bias of taxonomic relatedness is accounted for and when it is not. Independent contrasts analyses show that observed relationships among variables are not significantly different from the assumptions made to build the model or from its a priori predictions. We note that the dependence of the plant mass–density slope on the functions of structural mass provides a cause for the difference from the zero slope found in the animal population mass–density relationship; for the most part, animals do not have a comparable cumulative tissue type.