Influência da altura das garras dos pneus de um trator em área de plantio direto

This work was carried out to evaluate the performance of a farm tractor fitted with two sets of tires with high lugs and another set of tires with tallow lugs in straw without tillage (corn straw). The travel speeds used were approximately 4, 5, 6 and 7 km h(-1) and a constant pulling force of 25 kN was fixed. Tractor traction, forward speed, slip and consumption of fuel were measured and drawbar power, the ratio between the consumption and power and traction coefficient were calculated. It was observed that the tractor performance was similar to high and low lug tire conditions, in an area covered with corn straw.

Incorporação de resíduo de perfuração em matriz cerâmica: estabilização por solidificação

One of the waste generated during the drilling of oil wells are gravel which are impregnated of drilling fluid. This residue consists of highly toxic chemicals, including toxic metals. This study suggests an alternative process to the treatment of this waste, by incorporating it the form of raw material in the ceramic matrix , and by solidification and stabilize the metals present, Aluminum (Al), Iron (Fe), Manganese (Mn) and Zinc (Zn). The raw materials were characterized by the techniques of X ray fluorescence (FRX), X ray diffraction (DRX), laser granulometry (GL), thermogravimetry (TG) and differential thermal analysis (ADT). To evaluate the percentage of gravel effect the environmental and technological properties were obtained from formulations containing 0, 10 and 20 % by weight of gravel in the ceramic matrix. After sintering at temperatures 1080, 1120 and 1160 °C, the samples were tested for water absorption, the linear shrinkage firing, voltage of rupture and solubility. The results obtained showed that the stabilization by solidification, is a viable alternative to safe disposal of waste drilling. Ceramics products can be used in the manufacture of solid bricks

Engenharia de microestrutura em varistor à base de ZnO: evidências de homogeneidade e correlação com reações químicas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dinâmica populacional e alimentar de Stegastes fuscus, (Osteichthyes:pomacentridae) em arrecifes da praia de Búzius, no Rio Grande do Norte

The damselfish, Stegastes fuscus Cuvier, 1830 (Osteichthyes: Perciformes: Pomacentridae), is abundant in the coastal reefs of Búzios Beach, Rio Grande do Norte, Brazil and they play an important role in the reef community ecology. The present study investigated the feeding strategy of this species considering the food habits and morfo-histology of the digestive tract. Influence of the environmental correlates such as temperature, rainfall and luminosity in the tidal rock pools were studied. The fish were captured on a monthly basis from September 2004 to August 2005, during which period 842 individuals of S. fuscus were captured, 125 males, 437 females and 280 individuals without sex identification. The sex ratio observed was 1 M : 3,5 F. The total body length of males varied from 3.6 to 11.3 cm, with a mean of 7.77 cm; that of females varied from 2.9 to 11.4 cm, with a mean of 7.85 cm, and that of sex grouped individuals varied from 2.9 to 11.4 cm, with a mean of 7.83. However, there was no difference between males and females in total body length. This species presented a positive alometric growth and the equations obtained for the relation between body mass and total body length were: Wt =0,0174Lt 3,1123 for males; Wt =0,0137Lt 3,2294 for females and Wt = 0,0148Lt 3.1928 for sex grouped individuals. The relation between total body length and standard length was L t = 1 ,3223Ls + 0,1527 for sex grouped individual s. February to August was associated to a long period of gonadal resting. The fish spawned during January and in September -October. The frequency of fish with empty stomachs occurred during August to December, whereas frequency of fish with food contents i n stomachs occurred during January to July. This species is considered as a preferential herbivore based on the volume of macroalgae in its diet composition. The morfo -histological aspects of S. fuscus confirm herbivory. Among the environmental factors con sidered only rainfall showed a correlation with the feeding habits of this species

Influence of shot peening and hard chromium electroplating on the fatigue strength of 7050-T7451 aluminum alloy

Chromium electrodeposition is a technique for the production of functional coatings on engineering components. These coatings are extensively micro-cracked and present high level of hardness, resistance to corrosion and wear and low coefficient of friction. In this paper the shot peening influence on the fatigue strength of aluminum 7050-T7451 alloy chromium electroplated, was investigated.The shot peening process was carried out to create residual stresses using ceramic and glass shots. A hard chromium electroplated coating of 100 mu m thickness was performed on the base material and the shot peened base material surfaces. S-N curves were obtained in axial and bending fatigue tests and compared with the 7050-T7451 aluminum alloy. In order to study the influence of residual stresses on fatigue life, the behavior of compressive residual stress field was measured by an X-ray tensometry.An increase in the axial fatigue strength of 25% and 50% of ceramic and glass shots, respectively, was observed. The lower performance in fatigue life for ceramic-shot peening may be attributed to higher surface damage, as a consequence of the overpeening intensity performed. However, in bending fatigue the behavior was practically equivalent for both processes. Fracture surface analysis by scanning electron microscopy was used to observe crack origin sites from shot peened and chromium electroplated samples. (C) 2006 Elsevier Ltd. All rights reserved.

Effect of electroless nickel interlayer on the fatigue strength of chromium electroplated AISI 4340 steel

Deposition of wear-resistant hard chromium plating leads to a decrease in the fatigue strength of the base material. Despite the effective protection against wear and corrosion, fatigue life and environmental requirements result in pressure to identify alternatives or to improve conventional chromium electroplating mechanical characteristics. An interesting, environmentally safer and cleaner alternative for the replacement of hard chronic plating is tungsten carbide thermal spray coating, applied by high velocity oxyfuel (HVOF) process.To improve the fatigue strength of aeronautical steel chromium electroplated, shot peening is a successfully used method. Multiple lacer systems of coatings are considered to have larger resistance to crack propagation in comparison with simple layer.The aim of this study was to analyze the effect of nickel underplate on the fatigue strength of hard chromium plated AISI 4340 steel in two mechanical conditions: HRc 39 and HRc 52.Rotating bending fatigue tests results indicate that the clectroless nickel plating underlayer is responsible for the increase in fatigue strength of AISI 4340 steel chromium electroplated. This behavior may be attributed to the largest toughness/ductility and compressive residual stresses which, probably, arrested or delayed the inicrocrack propagation from the hard chromium external layer. The compressive residual stress field (CRSF) induced by the electroplating process was determined by X-ray diffraction method. The evolution of fatigue strength compressive residual stress field CRSF and crack sources are discussed and analyzed by SEM. (c) 2006 Elsevier Ltd. All rights reserved.

Effects of surface treatments on the fatigue strength of AISI 4340 aeronautical steel

Internal residual stresses significantly influence the fatigue strength of coated materials. It is well known that chromium plating is the most used electrodeposited coating for important industrial applications. However, pressure to identify alternatives or to improve the chromium electroplating process have increased in recent years, related to the reduction in fatigue strength of the base material and to environmental requirements. The high efficiency and fluoride free hard chromium electroplating there called accelerated) is an improvement to the conventional process. One environmentally safer and cleaner alternative to hard chromium plating is tungsten carbide thermal spray coating applied by the High Velocity Oxy-Fuel (HVOF) process. To increase the fatigue strength of chromium plated materials, coating thickness and microcracks density are important parameters to be controlled. Techniques as compressive residual stresses induced by shot peening and multilayers, are also used. The aim of this study was to analyse the effects on AISI 4340 steel, in the rotating bending fatigue behaviour, of the: tungsten carbide thermal spray coating applied by HP/HVOF process; chemical nickel underplate, and shot peening process applied before coating deposition, in comparison to hard chromium electroplatings. Rotating bending fatigue test results indicate better performance for the conventional hard chromium plating in relation to the accelerated hard chromium electroplating. Tungsten carbide thermal spray coating and accelerated hard chromium plate over nickel resulted in higher fatigue strength when compared to samples conventional or accelerated hard chromium plated. Shot peening showed to be an excellent alternative to increase fatigue strength of AISI 4340 steel hard chromium electroplated. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Considerations on corrosion and weld repair effects on the fatigue strength of a steel structure critical to the flight-safety

The aim of this study is to analyze the effects of corrosion and successive tungsten inert gas (TIC) welding repairs on the reverse bending fatigue strength of AISI 4130 steel used in components critical to the flight-safety. The tests were performed on hot-rolled steel plate specimens, 1.10 mm and 1.60 mm thick, by means of a SCHENK PWS equipment, with load ratio R = -1, constant amplitude, 30 Hz frequency and room temperature. It was observed that the reverse bending fatigue strength of AISI 4130 steel decreases due to the corrosion and the TIC welding and re-welding processes. (C) 2010 Elsevier Ltd. All rights reserved.

Fatigue behavior of PVD coated Ti-6Al-4V alloy

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel

Shot peening is a method widely used to improve the fatigue strength of materials. through the creation of a compressive residual stress field (CRSF) in their surface layers. In the present research the gain in fatigue life of AISI 4340 steel, Used in landing gear. is evaluated under four Shot peening conditions. Rotating bending fatigue tests were conducted and the CRSF was measured by an X-ray tensometry prior and during fatigue tests. It was observed that relaxation of the CRSF occurred due to the fatigue process. In addition, the fractured fatigue specimens were investigated using a scanning electron microscope in order to obtain information about the crack initiation points. The evaluation of fatigue life, relaxation of CRSF and crack sources are discussed. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

Internal carotid artery pseudoaneurysm after tonsillectomy treated by endovascular approach - A case report

Surgery on the head and neck region may be complicated by vascular trauma, caused by direct injury on the vascular wall. Lesions of the arteries are more dangerous than the venous one. The traumatic lesion may cause laceration of the artery wall, spasm, dissection, arteriovenous fistula, occlusion or pseudoaneurysm.We present a case of a child with a giant ICA pseudoaneurysm after tonsillectomy, manifested by pulsing mass and respiratory distress, which was treated by endovascular approach, occluding the lesion and the proximal artery with Histoacryl. We reinforce that the endovascular approach is the better way to treat most of the traumatic vascular lesions.

Comparison of progesterone-based protocols with gonadotropin-releasing hormone or estradiol benzoate for timed artificial insemination or embryo transfer in lactating dairy cows

The objective was to compare two protocols for synchronizing ovulation in lactating Holstein cows submitted to timed AI (TAI) or timed ET (TET). Within each farm (n = 8), cows (n = 883; mean +/- SEM 166.24 +/- 3.27 d postpartum, yielding 36.8 +/- 0.34 kg of milk/d) were randomly assigned to receive either: 1) an intravaginal progesterone insert (CIDR (R)) with 1.9 g of progesterone + GnRH on Day -10, CIDR (R) withdrawal + PGF2 alpha on Day -3, and 1 mg estradiol cypionate on Day -2 (treatment GP-P-E; n(TAI) = 180; n(TET) = 260); or 2) a CIDR (R) insert + 2 mg estradiol benzoate on Day -10, PGF2 alpha on Day -3, CIDR (R) withdrawal + 1 mg estradiol cypionate on Day -2 (treatment EP-P-E; n(TAI) = 174; n(TET) = 269). Cows were subsequently randomly assigned to receive either TAT on Day 0 or TET on Day 7. Serum progesterone concentration on Day -3 was greater in GP-P-E than in EP-P-E (2.89 +/- 0.15 vs 2.29 +/- 0.15 ng/mL; P < 0.01), with no significant effect of group on serum progesterone on Day 7. Compared to cows submitted to TAI, those submitted to TET had greater pregnancy rates on Day 28 (44.0% [233/5291 vs 29.7% [105/354]; p < 0.001) and on Day 60 (37.6% [199/529] vs 26.5 [94/354]; P < 0.001). However, there were no effects of treatments (GP-P-E vs EP-P-E; P > 0.10) on synchronization (87.0% [383/440] vs 85.3% [378/443]), conception (TAI: 35.3% [55/156] vs 33.8% [50/148]; TET: 50.7% [115/227] vs 51.3% [118/230]) and pregnancy rates on Days 28 (TAT: 30.5% [55/180] vs 28.7% 150/174]; TET: 44.2% [115/260] vs 43.9% [118/2691) and 60 (TAI: 27.2% [49/80] vs 25.9% [45/174]; TET: 38.8% [101/260] vs 36.4% [98/269]). In conclusion, GP-P-E increased serum progesterone concentrations on Day -3, but rates of synchronization, conception, and pregnancy were not significantly different between cows submitted to GP-P-E and EP-P-E protocols, regardless of whether they were inseminated or received an embryo. (c) 2011 Elsevier B.V. All rights reserved.

Efeito da gordura protegida sobre a produção e composição do leite em ovelhas da raça Bergamácia

Objetivou-se avaliar o efeito da gordura protegida sobre a produção e composição do leite em ovelhas da raça Bergamácia. Utilizaram-se 77 ovelhas distribuídas, por ordem de parição e idade, em duas dietas: uma composta de silagem de milho e concentrado; e outra com gordura protegida (35 g/ovelha/dia) no concentrado. As dietas foram isoenergéticas e isoproteicas e continham 70% NDT e 16% PB com base na matéria seca. Os cordeiros permaneceram com suas mães até os 45 dias de idade, quando foram desmamados. Quarenta e oito horas após o parto, deu-se início a ordenha realizada uma vez ao dia, às 7 h, para mensuração diária da produção de leite durante 60 dias. Amostras de leite foram coletadas semanalmente para análise da composição centesimal e do teor de caseína. A dieta com gordura protegida promoveu maior produção média diária de leite após a desmama (0,531 vs 0,489 kg/dia), entretanto, a produção total do período não diferiu entre controle e com gordura protegida (0,453 vs 0,468 kg/dia, respectivamente). Não foi observada influência das dietas sobre os teores de gordura do leite até a sexta semana de lactação. As diferenças ocorreram apenas após a desmama. Os teores de alfa e beta caseínas diferiram entre os grupos controle e gordura protegida (31,73 vs 18,56 Kda para alfa-caseína e 32,67 vs 26,44 Kda para beta-caseína, respectivamente). A adição de gordura protegida na dieta não altera a produção nem a composição centesimal do leite até a desmama.

PAR(2) and Temporomandibular Joint Inflammation in the Rat

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The bradycardic and hypotensive responses to serotonin are reduced by activation of GABA A receptors in the nucleus tractus solitarius of awake rats

We investigated the effects of bilateral injections of the GABA receptor agonists muscimol (GABA A) and baclofen (GABA B) into the nucleus tractus solitarius (NTS) on the bradycardia and hypotension induced by iv serotonin injections (5-HT, 2 µg/rat) in awake male Holtzman rats. 5-HT was injected in rats with stainless steel cannulas implanted bilaterally in the NTS, before and 5, 15, and 60 min after bilateral injections of muscimol or baclofen into the NTS. The responses to 5-HT were tested before and after the injection of atropine methyl bromide. Muscimol (50 pmol/50 nl, N = 8) into the NTS increased basal mean arterial pressure (MAP) from 115 ± 4 to 144 ± 6 mmHg, did not change basal heart rate (HR) and reduced the bradycardia (-40 ± 14 and -73 ± 26 bpm at 5 and 15 min, respectively, vs -180 ± 20 bpm for the control) and hypotension (-11 ± 4 and -14 ± 4 mmHg, vs -40 ± 9 mmHg for the control) elicited by 5-HT. Baclofen (12.5 pmol/50 nl, N = 7) into the NTS also increased basal MAP, but did not change basal HR, bradycardia or hypotension in response to 5-HT injections. Atropine methyl bromide (1 mg/kg body weight) injected iv reduced the bradycardic and hypotensive responses to 5-HT injections. The stimulation of GABA A receptors in the NTS of awake rats elicits a significant increase in basal MAP and decreases the cardiac Bezold-Jarisch reflex responses to iv 5-HT injections.