Islamic contributions to the International Organization for Science and Technology Education (IOSTE)

This presentation introduces the International Organization for Science and Technology Education (IOSTE), outlining its history, structure, principles and activities. It discusses the role of IOSTE as a values-oriented STE research organization established in response to cold war ideologies with the aim of encouraging dialogue and academic exchange. The presentation then highlights the recent engagement of IOSTE with STE in predominantly Muslim countries. It examines quantitatively and qualitatively the increasing contributions from researchers in these countries, and outlines possible future engagements which could lead to closer research collaborations and relationships between STE academics in Muslim and non-Muslim countries.

Development of optical ray tracing model of a standard parabolic trough collector

Parabolic trough concentrator collector is the most matured, proven and widespread technology for the exploitation of the solar energy on a large scale for middle temperature applications. The assessment of the opportunities and the possibilities of the collector system are relied on its optical performance. A reliable Monte Carlo ray tracing model of a parabolic trough collector is developed by using Zemax software. The optical performance of an ideal collector depends on the solar spectral distribution and the sunshape, and the spectral selectivity of the associated components. Therefore, each step of the model, including the spectral distribution of the solar energy, trough reflectance, glazing anti-reflection coating and the absorber selective coating is explained and verified. Radiation flux distribution around the receiver, and the optical efficiency are two basic aspects of optical simulation are calculated using the model, and verified with widely accepted analytical profile and measured values respectively. Reasonably very good agreement is obtained. Further investigations are carried out to analyse the characteristics of radiation distribution around the receiver tube at different insolation, envelop conditions, and selective coating on the receiver; and the impact of scattered light from the receiver surface on the efficiency. However, the model has the capability to analyse the optical performance at variable sunshape, tracking error, collector imperfections including absorber misalignment with focal line and de-focal effect of the absorber, different rim angles, and geometric concentrations. The current optical model can play a significant role in understanding the optical aspects of a trough collector, and can be employed to extract useful information on the optical performance. In the long run, this optical model will pave the way for the construction of low cost standalone photovoltaic and thermal hybrid collector in Australia for small scale domestic hot water and electricity production.

Corporate sustainability reporting of major commercial banks in line with GRI : Bangladesh evidence

Purpose – This paper aims to examine the tendencies of sustainability reporting by major commercial banks in Bangladesh in comparison with global sustainability reporting indicators outlined in the GRI framework together with banks' predilection toward reporting 16 GRI financial service sector (FSS) specific performance indicators. Design/methodology/approach – Based on the GRI G3 guidelines, the paper investigated banks' reporting in five broad areas of sustainability, such as environment, labour practices and decent works, product responsibility, human rights and society. The 2008/2009 annual reports of 12 major commercial banks listed on Dhaka stock exchange were analysed and coded using a content-based technique. Findings – The results show that information on society is addressed most extensively with regard to extent of reporting. This is followed by the disclosures prepared on decent works and labour practices and environmental issues. Furthermore, the disclosures of product responsibility information and the information for human rights are rather scarce in banks' reporting; on the subject of FSS-specific disclosures, only seven items out of 16 are disclosed by all sample banks. Research limitations/implications – The findings of the study indicate that Bangladeshi commercial banks' social disclosures could develop in this style to become more holistic and over time (in association with the country's central bank involvement) to resemble a type of structured reporting to the point where they are properly labelled per se. Originality/value – The study contributes to the social disclosure literature, in particular in a developing countries banking sector context, seeing as it disseminates evidence of the standing on social disclosures practices at the level of GRI with developing countries' banks data.

Disclosures of social value creation : a case study of three global social enterprises

This study seeks to fill in gap in the existing literature by looking at how and whether disclosure of social value creation becomes a part of legitimation strategies of social enterprises. By using legitimacy reasoning, this study informs that three global social organizations, Grameen Bank, Charity Water, and the Bill and Melinda Gates Foundation provide evidence of the use of disclosures of social value creation in order to conform with the expectations of the broader community—the community that wants to see poverty and injustice free world.

Evaluation of a pilot-scale oil extraction from microalgae for biodiesel production

Biodiesel derived from microalgae is one of a suite of potential solutions to meet the increasing demand for a renewable, carbon-neutral energy source. However, there are numerous challenges that must be addressed before algae biodiesel can become commercially viable. These challenges include the economic feasibility of harvesting and dewatering the biomass and the extraction of lipids and their conversion into biodiesel. Therefore, it is essential to find a suitable extraction process given these processes presently contribute significantly to the total production costs which, at this stage, inhibit the ability of biodiesel to compete financially with petroleum diesel. This study focuses on pilot-scale (100 kg dried microalgae) solvent extraction of lipids from microalgae and subsequent transesterification to biodiesel. Three different solvents (hexane, isopropanol (IPA) and hexane + IPA (1:1)) were used with two different extraction methods (static and Soxhlet) at bench-scale to find the most suitable solvent extraction process for the pilot-scale. The Soxhlet method extracted only 4.2% more lipid compared to the static method. However, the fatty acid profiles of different extraction methods with different solvents are similar, suggesting that none of the solvents or extraction processes were biased for extraction of particular fatty acids. Considering the cost and availability of the solvents, hexane was chosen for pilot-scale extraction using static extraction. At pilot-scale the lipid yield was found to be 20.3% of total biomass which is 2.5% less than from bench scale. Extracted fatty acids were dominated by polyunsaturated fatty acids (PUFAs) (68.94±0.17%) including 47.7±0.43 and 17.86±0.42% being docosahexaenoic acid (DHA) (C22:6) and docosapentaenoic acid (DPA) (C22:5, ω-3), respectively. These high amounts of long chain poly unsaturated fatty acids are unique to some marine microalgae and protists and vary with environmental conditions, culture age and nutrient status, as well as with cultivation process. Calculated physical and chemical properties of density, viscosity of transesterified fatty acid methyl esters (FAMEs) were within the limits of the biodiesel standard specifications as per ASTM D6751-2012 and EN 14214. The calculated cetane number was, however, significantly lower (17.8~18.6) compared to ASTM D6751-2012 or EN 14214-specified minimal requirements. We conclude that the obtained microalgal biodiesel would likely only be suitable for blending with petroleum diesel to a maximum of 5 to 20%.

Privacy by design for social networks

This research has established a new privacy framework, privacy model, and privacy architecture to create more transparent privacy for social networking users. The architecture is designed into three levels: Business, Data, and Technology, which is based on The Open Group Architecture Framework (TOGAF®). This framework and architecture provides a novel platform for investigating privacy in Social Networks (SNs). This approach mitigates many current SN privacy issues, and leads to a more controlled form of privacy assessment. Ultimately, more privacy will encourage more connections between people across SN services.

Crushed tablets : does the administration of food vehicles and thickened fluids to aid medication swallowing alter drug release?

Purpose. To evaluate the influence of co-administered vehicles on in vitro dissolution in simulated gastric fluid of crushed immediate release tablets as an indicator for potential drug bioavailability compromise. Methods. Release and dissolution of crushed amlodipine, atenolol, carbamazepine and warfarin tablets were tested with six foods and drinks that are frequently used in the clinical setting as mixers for crushed medications (water, orange juice, honey, yoghurt, strawberry jam and water thickened with Easythick powder) in comparison to whole tablets. Five commercial thickening agents (Easythick Advanced, Janbak F, Karicare, Nutilis, Viscaid) at three thickness levels were tested for their effect on the dissolution of crushed atenolol tablets. Results. Atenolol dissolution was unaffected by mixing crushed tablets with thin fluids or food mixers in comparison to whole tablets or crushed tablets in water, but amlodipine was delayed by mixing with jam. Mixing crushed warfarin and carbamazepine tablets with honey, jam or yoghurt caused them to resemble the slow dissolution of whole tablets rather than the faster dissolution of crushed tablets in water or orange juice. Crushing and mixing any of the four medications with thickened water caused a significant delay in dissolution. When tested with atenolol, all types of thickening agents at the greatest thickness significantly restricted dissolution, and products that are primarily based on xanthan gum also delayed dissolution at the intermediate thickness level. Conclusions. Dissolution testing, while simplistic, is a widely used and accepted method for comparing drug release from different formulations as an indicator for in vivo bioavailability. Thickened fluids have the potential to retard drug dissolution when used at the thickest levels. These findings highlight potential clinical implications of the addition of these agents to medications for the purpose of dose delivery and indicate that further investigation of thickened fluids and their potential to influence therapeutic outcomes is warranted.

A variant of the breast cancer type 2 susceptibility protein (BRC) repeat is essential for the RECQL5 Helicase to interact with RAD51 Recombinase for genome stabilization

The BRC repeat is a structural motif in the tumor suppressor BRCA2 (breast cancer type 2 susceptibility protein), which promotes homologous recombination (HR) by regulating RAD51 recombinase activity. To date, the BRC repeat has not been observed in other proteins, so that its role in HR is inferred only in the context of BRCA2. Here, we identified a BRC repeat variant, named BRCv, in the RECQL5 helicase, which possesses anti-recombinase activity in vitro and suppresses HR and promotes cellular resistance to camptothecin-induced replication stress in vivo. RECQL5-BRCv interacted with RAD51 through two conserved motifs similar to those in the BRCA2-BRC repeat. Mutations of either motif compromised functions of RECQL5, including association with RAD51, inhibition of RAD51-mediated D-loop formation, suppression of sister chromatid exchange, and resistance to camptothecin-induced replication stress. Potential BRCvs were also found in other HR regulatory proteins, including Srs2 and Sgs1, which possess anti-recombinase activities similar to that of RECQL5. A point mutation in the predicted Srs2-BRCv disrupted the ability of the protein to bind RAD51 and to inhibit D-loop formation. Thus, BRC is a common RAD51 interaction module that can be utilized by different proteins to either promote HR, as in the case of BRCA2, or to suppress HR, as in RECQL5.

What I want for my Social Network privacy

Social Networks (SN) users have various privacy requirements to protect their information; to address this issue, a six-stage thematic analysis of scholarly articles related to SN user privacy concerns were synthesized. Then this research combines mixed methods research employing the strengths of quantitative and qualitative research to investigate general SN users, and thus construct a new set of ?ve primary and Twenty-?ve secondary SN user privacy requirements. Such an approach has been rarely used to examine the privacy requirements. Factor analysis results show superior agreement with theoretical predictions and signi?cant improvement over previous alternative models of SN user privacy requirements. This research presented here has the potential to provide for the development of more sophisticated privacy controls which will increase the ability of SN users to: specify their rights in SNs and to determine the protection of their own SN data.

Effect of temperature and moisture on high pressure lipid/oil extraction from microalgae

Commercially viable carbon–neutral biodiesel production from microalgae has potential for replacing depleting petroleum diesel. The process of biodiesel production from microalgae involves harvesting, drying and extraction of lipids which are energy- and cost-intensive processes. The development of effective large-scale lipid extraction processes which overcome the complexity of microalgae cell structure is considered one of the most vital requirements for commercial production. Thus the aim of this work was to investigate suitable extraction methods with optimised conditions to progress opportunities for sustainable microalgal biodiesel production. In this study, the green microalgal species consortium, Tarong polyculture was used to investigate lipid extraction with hexane (solvent) under high pressure and variable temperature and biomass moisture conditions using an Accelerated Solvent Extraction (ASE) method. The performance of high pressure solvent extraction was examined over a range of different process and sample conditions (dry biomass to water ratios (DBWRs): 100%, 75%, 50% and 25% and temperatures from 70 to 120 ºC, process time 5–15 min). Maximum total lipid yields were achieved at 50% and 75% sample dryness at temperatures of 90–120 ºC. We show that individual fatty acids (Palmitic acid C16:0; Stearic acid C18:0; Oleic acid C18:1; Linolenic acid C18:3) extraction optima are influenced by temperature and sample dryness, consequently affecting microalgal biodiesel quality parameters. Higher heating values and kinematic viscosity were compliant with biodiesel quality standards under all extraction conditions used. Our results indicate that biodiesel quality can be positively manipulated by selecting process extraction conditions that favour extraction of saturated and mono-unsaturated fatty acids over optimal extraction conditions for polyunsaturated fatty acids, yielding positive effects on cetane number and iodine values. Exceeding biodiesel standards for these two parameters opens blending opportunities with biodiesels that fall outside the minimal cetane and maximal iodine values.

Factors affecting new project delays in Saudi Arabian manufacturing organisations

Delay in the delivery of manufacturing projects is a major problem in manufacturing industries. This research investigates the factors that influence the lead time of new projects in manufacturing organisations. Employing a questionnaire survey and interview methodologies, this study collected data from five leading manufacturing organisations as well as their suppliers and contractors in Saudi Arabia to examine what, how and why the new project implementation delay occurs. Results show that the main factors contributing to manufacturing delays are related to people and material. On the other hand, social, political and cultural factors were the least significant factors as per the outcome of this study. Views of manufacturers, suppliers and contractors regarding causes of delays have also been analysed.

Synthesis and toxicological evaluation of a chitosan‑L‑leucine conjugate for pulmonary drug delivery applications

Herein are reported the synthesis of a conjugate of chitosan with L-leucine, the preparation of nanoparticles from both chitosan and the conjugate for use in pulmonary drug delivery, and the in vitro evaluation of toxicity and inflammatory effects of both the polymers and their nanoparticles on the bronchial epithelial cell line, BEAS-2B. The nanoparticles, successfully prepared both from chitosan and the conjugate, had a diameter in the range of 10−30 nm. The polymers and their nanoparticles were tested for their effects on cell viability by MTT assay, on trans-epithelial permeability by using sodium fluorescein as a fluid phase marker, and on IL-8 secretion by ELISA. The conjugate nanoparticles had a low overall toxicity (IC50 = 2 mg/mL following 48 h exposure; no induction of IL-8 release at 0.5 mg/mL concentration), suggesting that they may be safe for pulmonary drug delivery applications.

Colloidal drug probe : Method development and validation for adhesion force measurement using Atomic Force Microscopy

This study demonstrates a novel technique of preparing drug colloid probes to determine the adhesion force between a model drug salbutamol sulphate (SS) and the surfaces of polymer microparticles to be used as carriers for the dispersion of drug particles from dry powder inhaler (DPI) formulations. Model silica probes of approximately 4 lm size, similar to a drug particle used in DPI formulations, were coated with a saturated SS solution with the aid of capillary forces acting between the silica probe and the drug solution. The developed method of ensuring a smooth and uniform layer of SS on the silica probe was validated using X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Using the same technique, silica microspheres pre-attached on the AFM cantilever were coated with SS. The adhesion forces between the silica probe and drug coated silica (drug probe) and polymer surfaces (hydrophilic and hydrophobic) were determined. Our experimental results showed that the technique for preparing the drug probe was robust and can be used to determine the adhesion force between hydrophilic/ hydrophobic drug probe and carrier surfaces to gain a better understanding on drug carrier adhesion forces in DPI formulations.