Phosphate fertilization and phosphorus forms in an Oxisol under no-till

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Medição da densidade óssea através de ondas eletromagnéticas e classificação por MVS

This work holds the purpose of presenting an auxiliary way of bone density measurement through the attenuation of electromagnetic waves. In order to do so, an arrangement of two microstrip antennas with rectangular configuration has been used, operating in a frequency of 2,49 GHz, and fed by a microstrip line on a substrate of fiberglass with permissiveness of 4.4 and height of 0,9 cm. Simulations were done with silica, bone meal, silica and gypsum blocks samples to prove the variation on the attenuation level of different combinations. Because of their good reproduction of the human beings anomaly aspects, samples of bovine bone were used. They were subjected to weighing, measurement and microwave radiation. The samples had their masses altered after mischaracterization and the process was repeated. The obtained data were inserted in a neural network and its training was proceeded with the best results gathered by correct classification on 100% of the samples. It comes to the conclusion that through only one non-ionizing wave in the 2,49 GHz zone it is possible to evaluate the attenuation level in the bone tissue, and that with the appliance of neural network fed with obtained characteristics in the experiment it is possible to classify a sample as having low or high bone density

Desempenho mecânico de compósitos híbridos de fibras naturais e poliéster não saturado

With the objective to promote sustainable development, the fibres found in nature in abundance, which are biodegradable, of low cost in comparison to synthetic fibres are being used in the manufacture of composites. The mechanical behavior of the curauá and pineapple leaf fibre (PALF) composites in different proportions, 25% x 75% (P1), 50% x 50% (P2) e 75% x 25% (P3) were respectively studied, being initially treated with a 2% aqueous solution of sodium hydroxide. Mechanical analyses indicated that with respect to studies of traction, for the combination of P1 and P3, better results of 22.17 MPa and 16.98 MPa, were obtained respectively, which are higher than that of the combination P2. The results of the same pattern were obtained for analysis of bending resistance where P1 is 1.21% and P3 represents 0.96%. In the case of resistance to bending, best results were obtained for the combination P1 at 49.07 MPa. However, when Young's modulus values were calculated, the values were different to the pattern of the results of other tests, where the combination P2 with the value of 4.06 GPa is greater than the other combinations. This shows that the PALF had a greater influence in relation to curauá fibre. The analysis of the results generally shows that in combinations of two vegetable fibers of cellulosic origin, the fiber which shows higher percentage (75%) is the best option than to the composition of 50%/50%. In the meantime, according to the results obtained in this study, in the case where the application should withstand bending loads, the better composition would be 50%/50%

Análise topológica experimental por perfilometria cíclica indutiva de superficies de paredes estruturais

To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies

Beneficiamento de sementes de café e efeitos na qualidade física

A pesquisa foi realizada com o objetivo de verificar a possibilidade de uso da máquina de pré-limpeza, da máquina de limpeza e classificação (ventiladores e peneiras) e da mesa densimétrica para o beneficiamento de sementes de café e, paralelamente, avaliar seus efeitos na qualidade física do lote. Para essa finalidade, um lote de sementes de café arábica 'Catuaí Amarelo IAC 62' foi submetido ao beneficiamento nesses três equipamentos, em diversas combinações. As frações retidas pelas peneiras 22/64 e 20/64 avos de polegada, na máquina de ventiladores e peneiras, constituíram a maior parte do lote e foram processadas, separadamente, em mesa densimétrica. Foram realizadas avaliações de pureza física, massa de mil sementes, peso hectolítrico, teor de água, tipos de sementes predominantes e integridade do endocarpo. Observou-se que: a) A máquina de pré-limpeza, a máquina de ventiladores e peneiras e a mesa densimétrica foram eficientes para a homogeneização do lote de sementes de café, proporcionando obtenção de melhor qualidade física na seqüência operacional em que foram utilizadas de forma conjugada; b) O uso de peneiras com crivos oblongos e crivos circulares, intercaladas na máquina de ventiladores e peneiras, possibilitou a separação de sementes mocas, de sementes com resíduos de exocarpo aderidos ao endocarpo e de sementes desprovidas de endocarpo, melhorando a aparência do lote; c) A mesa densimétrica foi o equipamento que proporcionou melhor separação de sementes com endocarpo danificado, bem como alterações favoráveis à qualidade física do lote; d) As sementes pequenas, retidas nas menores peneiras da máquina de ventiladores e peneiras, e as sementes de menor massa específica, classificadas ou não por tamanho e coletadas na descarga inferior da mesa densimétrica, foram as de baixa qualidade física.

Beneficiamento de sementes de café e efeitos na qualidade fisiológica

Considerando-se a escassez de informações sobre o beneficiamento mecanizado de sementes de café, realizou-se este trabalho para estudar seus efeitos na qualidade fisiológica das sementes de café arábica. Um lote de sementes de 'Catuaí Amarelo IAC 62' foi submetido à ação de máquina de pré-limpeza, máquina de ventiladores e peneiras e mesa densimétrica, em diversas combinações, e as sementes foram avaliadas quanto à germinação e ao vigor (envelhecimento acelerado, emergência de plântulas, altura e massa de matéria seca de plântulas e mudas). O teor de água das sementes também foi determinado. Utilizou-se o delineamento estatístico de blocos ao acaso, com quatro repetições, e o teste de Tukey a 5% para comparação de médias. Concluiu-se que: a) a qualidade fisiológica das sementes foi aprimorada à medida que o lote passou por equipamentos específicos no beneficiamento, culminando com a melhor qualidade na seqüência operacional em que o lote foi submetido à ação da máquina de ventiladores e peneiras e mesa densimétrica; b) a mesa densimétrica, associada à máquina de ventiladores e peneiras, foi o equipamento que proporcionou a melhor separação de materiais que interferem negativamente na qualidade fisiológica das sementes; c) as sementes maiores e/ou mais pesadas tiveram qualidade fisiológica superior, e as sementes mocas graúdas, qualidade fisiológica similar à das sementes chatas graúdas; d) o descarte das frações do lote constituídas por sementes pequenas ou de menor densidade possibilitou a obtenção de lotes homogêneos e com alta qualidade fisiológica, favorecendo a obtenção de mudas mais vigorosas.

Teste de condutividade elétrica em função do número de sementes e da quantidade de água para sementes de milheto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Depósitos de calda de pulverização nas faces adaxial e abaxial de folhas de Eichhornia crassipes dispostas em diferentes ângulos

Estudos foram conduzidos com o objetivo de avaliar os depósitos de gotas pulverizadas através de dois tipos de pontas sobre as faces adaxial e abaxial de folhas de Eichhornia crassipes dispostas em diferentes ângulos. No primeiro estudo, os tratamentos foram dispostos no esquema fatorial 2x4x7: dois tipos de pontas (TX12 e XR11002VS), quatro ângulos verticais (0º, 30º, 60º e 90º) e sete ângulos horizontais (0º, 15º, 30º, 45º, 60º, 75º e 90º). No ângulo vertical de 90º a lâmina foliar foi posicionada paralelamente ao sentido de deslocamento do jato de pulverização; e no ângulo horizontal de 90º a folha foi posicionada perpendicularmente ao plano do solo. Como traçadores, foram utilizadas soluções de 1.000 ppm do corante Azul FDC-1 e 3.500 ppm do corante Amarelo Tartrasina para as pontas tipo leque e cone, respectivamente. No segundo estudo, os tratamentos foram dispostos no esquema fatorial 2x2x3: dois tipos de pontas (TX12 e XR11002VS), dois tipos de calda (com e sem Aterbane BR a 0,5%) e três ângulos horizontais (0º, 45º e 90º). Adotou-se o ângulo vertical de 90º como padrão para todos os tratamentos. Soluções de 1.000 ppm do corante Azul FDC-1 e 3.500 ppm do corante Amarelo Tartrasina foram utilizadas como traçadores para a calda com e sem surfatante, respectivamente. Os resultados do primeiro estudo revelaram que os depósitos observados em toda a folha e na face adaxial das lâminas foliares de aguapé diminuíram à medida que se aumentou a angulação vertical, independentemente da ponta utilizada. Os menores depósitos sempre estiveram relacionados ao ângulo vertical de 90º, independentemente do ângulo horizontal utilizado. Não foi detectado nenhum depósito na face abaxial das folhas de aguapé em todas as combinações dos fatores estudados. No segundo estudo também foram observados os mesmos decréscimos no volume de calda depositado em toda a folha e na face adaxial à medida que se aumentou a angulação vertical das lâminas foliares. As duas pontas proporcionaram depósitos nulos na face abaxial quando o surfatante não foi utilizado; entretanto, a adição do surfatante à calda incrementou significativamente os depósitos nesta face da folha do aguapé.

Comparação da precisão dos resultados do teste de tetrazolio usando a metodologia alternativa e a tradicional em sementes de soja

The use of tetrazolium testing is recognized in the soybean seed quality control due to the large amount of data which it provides. Although it is considered a quick test, in 1998 an alternative methodology was proposed for the seed preconditioning, which allows 10 hours of time saving in seeds preparation. The objective of this research is to compare the accuracy of the new and the traditional tetrazolium testing. Three soybean seed genotypes were used, Conquista, Garantia and M-soy 8400, all 2000/2001 crop. The seeds were evaluated in relation to germination, evaluated with the traditional (TZt) and the alternative (Tza) tetrazolium test as well as with the accelerated aging performed in two different conditions (45 degrees C 24h(-1) and 45 degrees C 72h(-1)). After aging, the seeds too were submitted to TZt and Tza testing. The experimental design was a randomized blocks, with four replicates the 50 seeds per genotype in every evaluation, with exception only for tetrazolium test, with two replicates. The averages were compared in the Tukey test level of 5% probability. The comparison between the two methodologies in relation to level of vigor (class 1 to 3) and germination potential (class 1 to 5) indicated no statistical discrepancies, for aged non-aged seeds. This, the use of the alternative tetrazolium test is recommend in case a reduced seed preparation time is needed.

Estudo da desidratação de tomates em pedaços com pré-tratamento osmótico

Vegetables drying plays an important role in the field of food dehydration, being a very old practice that was originated from sun drying items of food in order to preserve them to be consumed during the periods of scarcity. One of these vegetables is the tomato, that was originally grown in South America. Tomatoes are easily perishable after being picked up from the tree and this makes the process of tomato dehydration a challenge due to the high amount of water (95%) contained in them. The present research work was mainly intended to develop alternative processes for tomato conservation, by drying slices of skinned and unskinned tomatoes in the in natura form or in the osmotically pre-dehydrated form. Firstly, the best conditions of the osmotic pre-dehydration process were defined including temperature, immersion time and concentration of the osmotic solution, based on the results of water loss, solids gain and weigh reduction of the pre-dehydration tomatoes at different processing conditions. The osmotic solution used was made up of NaCl (5 and 10%) and sucrose (25 and 35%) at different combinations. For a fixed conditions of osmotic pre-dehydration, the drying tests of the pre-processed and in natura tomatoes were carried out in a stove with air circulation and a convective dryer with trays, at two levels of temperature. The sensorial analysis of the osmotically pre-treated and unskinned dehydrated tomatoes was carried out as well as a study on the their shelf-live. The results obtained showed that the drying of the tomatoes took place as a result of the internal control of the water transport, and did not show a constant rate, while two distinct periods of the decreasing phase were observed. The osmotic pre treatment substancially reduced the initial amount of humidity in the tomatoes, thus reducing the necessary time for the product to attain levels of intermediate humidity. The impermeability of the tomato skin was identified as well as the unfavorable influence of the pre-treatment on the unskinned tomatoes, whose solid gain brought about a decrease in the water activity with subsequent reduction of the drying rate. Despite the various simplifications carried out during the development of this study, the proposed diffusive model adjusted to the experimental data satisfactorily, thus making it possible to determine the effective coefficients of diffusion, whose results were consistent and compatible with those found in the current literature. Concerning the higher rates of evaporation and the lowest processing time, the best results were obtained in the drying of the unskinned, in natura tomatoes and of the skinned, pre-dehydrated tomatoes, at 60ºC, both processed in the convective drier. The results of the sensorial analysis of the unskinned and pre-treated product did not prove to be satisfactory. Regarding the shelf-live of the tomatoes, for a period of 45 days, no physicochemical or microbiological alteration of the product was noted

Indução do florescimento e crescimento de tangerineira 'Poncã' (Citrus reticulata Blanco) em função da irrigação e da aplicação de paclobutrazol

O experimento foi conduzido na Faculdade de Ciências Agronômicas - UNESP/Câmpus de Botucatu (SP), com o objetivo de avaliar o florescimento fora de época e o crescimento vegetativo da tangerineira 'Poncã'. Nesse contexto, adotou-se o delineamento estatístico em blocos casualizados, em parcelas subdivididas, com duas repetições, na instalação do ensaio. Os dois tratamentos de -0,03 e -0,05 MPa, como potenciais mínimos da água no solo, constituíram as parcelas e as quatro doses de paclobutrazol: 0; 4; 8 e 12 g por planta, nas subparcelas. No segundo ano de pesquisa, foram mantidas as mesmas parcelas e foram aplicadas nas plantas das subparcelas as doses de 0; 500; 1000 e 2000 mg l-1 de paclobutrazol, via foliar. Cada parcela foi constituída de 16 plantas, sendo oito destinadas à avaliação. Utilizou-se, em ambas as combinações, de um tratamento sem irrigação (-0,07 MPa) e sem aplicação de paclobutrazol, como testemunha. Foram avaliados parâmetros, como a altura, diâmetro médio, volume e área de projeção da copa e condutância estomática para caracterizar a resposta das plantas aos tratamentos empregados. Concluiu-se que a aplicação do paclobutrazol e a variação do potencial da água no solo não proporcionaram a indução do florescimento fora de época das tangerineiras, e que os níveis de paclobutrazol influenciaram no desenvolvimento das plantas.

Recuperação e purificação de proteínas do soro de queijo tipo coalho usando cromatografia de troca iônica e interação hidrofóbica em leito na forma expandida

Expanded Bed Adsorption plays an important role in the downstream processing mainly for reducing costs as well as steps besides could handling cells homogenates or fermentation broth. In this work Expanded Bed Adsorption was used to recover and purify whey proteins from coalho cheese manufacture using Streamline DEAE and Streamline SP both ionic resins as well as a hydrophobic resin Streamline Phenyl. A column of 2.6 cm inner diameter with 30 cm in height was coupled to a peristaltic pump. Hydrodynamics study was carried out with the three resins using Tris-HCl buffer in concentration of 30, 50 and 70 mM, with pH ranging from 7.0 to 8.0. In this case, assays of the expansion degree as well as Residence Time Distribution (RTD) were carried out. For the recovery and purification steps, a whey sample of 200 mL, was submitted to a column with 25mL of resin previously equilibrated with Tris/HCl (50 mM, pH 7.0) using a expanded bed. After washing, elution was carried out according the technique used. For ionic adsorption elution was carried out using 100 mL of Tris/HCl (50 mM, pH 7.0 in 1M NaCl). For Hydrophobyc interaction elution was carried out using Tris/HCl (50 mM, pH 7.0). Adsorption runs were carried out using the three resins as well as theirs combination. Results showed that for hydrodynamics studies a linear fit was observed for the three resins with a correlation coefficient (R2) about 0.9. In this case, Streamline Phenyl showed highest expansion degree reaching an expansion degree (H0/H) of 2.2. Bed porosity was of 0.7 when both resins Streamline DEAE and Streamline SP were used with StremLine Phenyl showing the highest bed porosity about 0.75. The number of theorical plates were 109, 41.5 and 17.8 and the axial dipersion coefficient (Daxial) were 0.5, 1.4 and 3.7 x 10-6 m2/s, for Streamline DEAE, Streamline SP and Streamline Phenyl, respectively. Whey proteins were adsorved fastly for the three resins with equilibrium reached in 10 minutes. Breakthrough curves showed that most of proteins stays in flowthrough as well as washing steps with 84, 77 and 96%, for Streamline DEAE, Streamline SP and Streamline Phenyl, respectively. It was observed protein peaks during elution for the three resins used. According to these peaks were identified 6 protein bands that could probably be albumin (69 KDa), lactoferrin (76 KDa), lactoperoxidase (89 KDa), β-lactoglobulin (18,3 KDa) e α-lactoalbumin (14 KDa), as well as the dimer of beta-lactoglobulin. The combined system compound for the elution of Streamline DEAE applied to the Streamline SP showed the best purification of whey proteins, mainly of the α-lactoalbumina

Integração de imagem aérea de alta resolução e dados de varredura a laser na classificação de cenas urbanas para detectar regiões de via

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Pré-fabricados lingüísticos: estrutura e funcionamento de sintagmas verbais idiomatizados - por uma abordagem cognitivo-funcional em sala de aula

This work aims at under the cognitive-functional perspective describing, inside the vast domain of the linguistic prefabs, the structure and the functioning of the Idiomatic Verb Phrases (SVIs), produced by speakers of the Portuguese from Brazil, located in Natal (RN). From the functionalist presupposition that the language is used essentially to assist to communicative demands, it is observed that its morphologic-syntactic structure is conditioned to the inherent pragmatic vicissitudes to the verbal interaction of subjects, socially heterogeneous and historically established. It is focalized, in the composition of SVIs, the relationships VT + OD (transitive verb + direct object), characterizing the syntactic-semantic nature of the verb and of the respective verbal complement. Those verb combinations + complement can be interpreted as lexical structures, reflexes of the idiomaticity inherent to conventional constructions already systematized in the users' of the language cultural repertoire. It is sought, still, to glimpse the cognitive and discursive motivations pertinent to that linguistic phenomenon. In the investigative process, are analyzed exclusive data of speech collected in Corpus Discurso & Gramática a lingua falada e escrita na cidade do Natal, organized by Furtado da Cunha (1998). The adopted methodological procedures configure as methods of empiric analysis and use of the intuition, being emphasized the qualitative approach (explanatory) of the data with quantitative support of statistical indicators. It shows, finally, a grating of didactic suggestions on SVIs, for Portuguese's classes, as subsidies to the educational practice in the Medium Teaching and in the course of Letters.

Propagação de danos em sistemas cooperativos: propriedades termodinâmicas

High-precision calculations of the correlation functions and order parameters were performed in order to investigate the critical properties of several two-dimensional ferro- magnetic systems: (i) the q-state Potts model; (ii) the Ashkin-Teller isotropic model; (iii) the spin-1 Ising model. We deduced exact relations connecting specific damages (the difference between two microscopic configurations of a model) and the above mentioned thermodynamic quanti- ties which permit its numerical calculation, by computer simulation and using any ergodic dynamics. The results obtained (critical temperature and exponents) reproduced all the known values, with an agreement up to several significant figures; of particular relevance were the estimates along the Baxter critical line (Ashkin-Teller model) where the exponents have a continuous variation. We also showed that this approach is less sensitive to the finite-size effects than the standard Monte-Carlo method. This analysis shows that the present approach produces equal or more accurate results, as compared to the usual Monte Carlo simulation, and can be useful to investigate these models in circumstances for which their behavior is not yet fully understood