Treatment effects produced by the Bionator appliance. Comparison with an untreated Class II sample

The purpose of this retrospective investigation was to evaluate the dentoalveolar and skeletal cephalometric changes of the Bionator appliance on individuals with a Class II division 1 malocclusion. Lateral cephalograms of 44 patients were divided into two equal groups. The control group comprised 22 untreated Class II children (11 males, 11 females), with an initial mean age of 8 years 7 months who were followed without treatment for a period of 13 months. The Bionator group (111 males, 11 females) had an initial mean age of 10 years 8 months, and were treated for a mean period of 16 months. Lateral cephalometric headfilms were obtained of each patient and control at the beginning and end of treatment.The results showed that there were no changes in forward growth of the maxilla in the experimental group compared with the control group. However, the Bionator treatment produced a statistically significant increase in mandibular protrusion, and in total mandibular and body lengths. There were no statistically significant differences in craniofacial growth direction between the Bionator group and the control group, although the treated patients demonstrated a greater increase in posterior face height. The Bionator appliance produced labial tipping of the lower incisors and lingual inclination of the upper incisors, as well as a significant increase (P < 0.01) in mandibular posterior dentoalveolar height. The major effects of the Bionator appliance were dentoalveolar, with a smaller significant skeletal effect. The results indicate that the correction of a Class II division 1 malocclusion with the Bionator appliance is achieved not only by a combination of mandibular skeletal effects, but also by significant dentoalveolar changes.

Whole-body protein turnover in malnourished patients with child class B and C cirrhosis on diets low to high in protein energy

The purpose of this study was to determine the rate of whole-body protein turnover in moderately and severely alcoholic, malnourished, cirrhotic patients fed with different amounts of protein or energy. Six male patients (Child classes B and C) and four age- and sex-matched healthy control subjects were studied for 18 d in fasting and feeding states; a single oral dose of [N-15]glycine was used as a tracer and urinary ammonia was the end product. The kinetic study showed that patients had higher protein catabolism while fasting (patients: 3.14 +/- 1.2 g of lean body mass/9 h; controls: 1.8 +/- 0.3 g of lean body mass/9 h: P<0.02). Although not statistically significant, protein catabolism (grams of lean body mass/9 h) was lower with the hyperproreic/hyperenergetic diet when compared with fasting. Nitrogen retention was consistent with the lower protein-catabolism rate; a statistically significant increase in nitrogen balance was observed when patients were fed with the hyperproteic/hyperenergetic diet compared with fasting 14.3 +/- 3.2 g of nitrogen/d and -2.2 +/- 1.9 g of nitrogen/d, respectively; P < 0.01). These data indicate that Child class B and C cirrhotic patients are hypercatabolic and that Long-term nutritional intervention with a hyperproteic/hyperenergetic diet is likely needed to improve their clinical and nutritional status. Nutrition 2001;17:239-242. (C) Elsevier B.V. 2001.

Polymerization shrinkage: effects of boundary conditions and filling technique of resin composite restorations

Objective: To evaluate the linear polymerization shrinkage (LPS) and the effect of polymerization shrinkage of a resin composite and resin-dentin bond strength under different boundary conditions and filling techniques.Methods: Two cavities (4 x 4 x 2 MM) were prepared in bovine incisors (n = 30). The teeth were divided into three groups, according to boundary conditions: In group TE, the total-etch technique was used. In group EE, only enamel was conditioned, and in group NE, none of the watts of the cavities were conditioned. A two-step adhesive system was applied to all cavities. The resin composite was inserted in one (B) or three increments (1), and tight-cured with 600 mW/cm(2) (80 s). The LPS (%) was measured in the top-bottom direction, by placing a probe in contact with resin composite during curing. Enamel and total mean gap widths were measured (400 x) in three slices obtained after sectioning the restorations. Then, the slices were sectioned again, either to obtain sticks from the adhesive interface from the bottom of the cavity or to obtain resin composite sticks (0.8 mm(2)) to be tested for tensile strength (Kratos machine, 0.5 mm/min). The data was subjected to a two-way repeated measures ANOVA and Tukey's test for comparison of the means (alpha = 0.05).Results: the highest percentage of LPS was found for the TE when bulk fitted, and the lowest percentage of LPS was found in the Hand NE when incrementally fitted. The resin dentin bond strength was higher and the total mean gap width was tower for TE group; no significant effect was detected for the main factor fitting techniques. No difference was detected for the tensile strength of resin composite among the experimental groups.Conclusions: the filling technique is not able to minimize effects of the polymerization shrinkage, and bonding to the cavity watts is necessary to assure reduced mean gap width and high bond strength values. (C) 2004 Elsevier Ltd. All rights reserved.

Periodic orbits for a class of reversible quadratic vector field on R-3

For a class of reversible quadratic vector fields on R-3 we study the periodic orbits that bifurcate from a heteroclinic loop having two singular points at infinity connected by an invariant straight line in the finite part and another straight line at infinity in the local chart U-2. More specifically, we prove that for all n is an element of N, there exists epsilon(n) > 0 such that the reversible quadratic polynomial differential systemx = a(0) + a(1y) + a(3y)(2) + a(4Y)(2) + epsilon(a(2x)(2) + a(3xz)),y = b(1z) + b(3yz) + epsilon b(2xy),z = c(1y) +c(4az)(2) + epsilon c(2xz)in R-3, with a(0) < 0, b(1)c(1) < 0, a(2) < 0, b(2) < a(2), a(4) > 0, c(2) < a(2) and b(3) is not an element of (c(4), 4c(4)), for epsilon is an element of (0, epsilon(n)) has at least n periodic orbits near the heteroclinic loop. (c) 2007 Elsevier B.V. All rights reserved.